AVIZAR

Multicopter T-motor style (flat center) Pair of 16x5.5 Carbon Fiber Propellers CW/CCW

Specifications:

• Material: Carbon fiber
• Epoxy resin cover
• Size: 16x5.5 cw, 16x5.5 ccw
• High gloss 3K finish
• Very strong and light weight
• Included : Pair: 1 CW, 1 CCW

 

The most common form of radially fitted circlips for shafts with grooves. Provide a large shoulder on a relatively small shaft diameter. The three prongs of the E-Clip make contact with the bottom of the groove and provide a shoulder for effective retention of the assemblies.

Standard material: Carbon Spring Steel SAE 1060-109
Standard Finish: Phosphate and Oil Benefits
Cost effective replacement, durable, removable.

Assortment of E-Clips. Pack of 10 pcs, Sizes of #2-2.5-3-4-5-6 ( Size sometimes shown as # symbol )

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those  Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

•   Technology : 3K Matte Twill Matte
  
•   Size:15mm OD/ 13mm ID
•   Length: 1000mm
•   Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those  Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

•   Technology : 3K Matte Twill Matte
  
•   Size:20mm OD/ 18mm ID
•   Length: 1000mm
•   Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

• Technology : 3K Matte Twill Matte
  
• Size:22mm OD/ 20mm ID
• Length: 900-1000mm
• Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

• Technology : 3K Matte Twill Matte
  
• Size:24mm OD/ 22mm ID
• Length: 1000mm
• Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

• Technology : 3K Matte Twill Matte
  
• Size:25mm OD/ 23mm ID
• Length: 1000mm
• Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

• Technology : 3K Matte Twill Matte
• Size:35mm OD/ 33mm ID
• Length: 1000mm
• Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Can be used as replacement for Boom, Sky hero tubes and more.

Specifications:

• Technology : 3K Matte Twill Matte
• Size:40mm OD/ 37mm ID
• Length: 1000mm
• Quantity: 1pc

Our carbon tubes also used in Light aviation and UAV, the tubes are tested into Bending force.

Those Roll wrapped carbon fiber tubes are manufactured by wrapping multiple layers of 12k UD and 3k twill carbon fibre pre-pregs around a metal mold and then cured at high temperature. The UD pre-pregs are used in core layers whereas the twill is on the surface.

Carbon Fiber 3k Roll wrapped high strength carbon fiber tubes matte twill tube finish.

Specifications:

•  Technology : 3K Matte Twill Matte
•  Size: 8mm OD / 6mm ID
•  Length: 1000mm
•  Quantity: 1pc

Power Distribution  Board for CC3D flight controller

Features:

• Mini size,Light weight.(only 3.5g)
• The same size  and hole location as CC3D
• Integrated 2 switch to control LED and FPV equipments

Package included:

1 x CC3D flight controller  Distribution Power Board

Century Servo Mount set with Wire lock and Pushrod extension

Included in the set
10 x Servo Mount set
2 x  Servo wire mounting lock
1 Pushrod extension for  2-3mm

CFK fork servo lever 25mm Futaba

Specifications:

• Fork servo lever with precise teeth (variant).
• Gap servo driven ball center to 25mm.
• Fork opening 5 mm.
• Weight 0.8g.
• Comes with built-in ball joint and M2 screw with lock nut.
• The high torque of modern digital servos must be free of play and smoothly to the driven element f/exp Rudderblades.
• The redesign of our fork servo lever is designed for ruggedness.
• The power dissipation occurs in the middle of the servo gearing.
• The execution of a fork lever effectively prevents misjudged the servo drive output.
• The servo gear will last longer.
• Our servo arms are made of highly compressed carbon fiber plastic ago (nylon with 45% carbon fiber content).
• At 300 ° C and under high pressure (1800 bar) the leverage to get their appearance in hardened steel molds.
• Since this method has similarities with the manufacture of highly stressed components in large aircraft, we have taken it for making our servo arm.
• The result is a high strength component which need not fear comparison with Duralaluminium.
• However, it is lighter and vibration resistant.
• All servo lever are manufactured in Germany using the latest CNC machines.

 

CFK fork servo lever 30mm Futaba

Specifications:

• Fork servo lever with precise teeth (variant).
• Gap servo driven ball center to 30mm.
• Fork opening 5 mm.
• Weight 1.5g.
• Comes with built-in ball joint and M2 screw with lock nut.
• The high torque of modern digital servos must be free of play and smoothly to the driven element f/exp Rudderblades.
• The redesign of our fork servo lever is designed for ruggedness.
• The power dissipation occurs in the middle of the servo gearing.
• The execution of a fork lever effectively prevents misjudged the servo drive output.
• The servo gear will last longer.
• Our servo arms are made of highly compressed carbon fiber plastic ago (nylon with 45% carbon fiber content).
• At 300 ° C and under high pressure (1800 bar) the leverage to get their appearance in hardened steel molds.
• Since this method has similarities with the manufacture of highly stressed components in large aircraft, we have taken it for making our servo arm.
• The result is a high strength component which need not fear comparison with Duralaluminium.
• However, it is lighter and vibration resistant.
• All servo lever are manufactured in Germany using the latest CNC machines.

 

CFK fork servo lever 38mm Futaba

Specifications:

• Gap servo driven ball center to 38mm.
• Fork opening 6mm.
• Fork hole for M3 thread. Weight 3g.
• Comes with built-in ball joint
• The high torque of modern digital servos must be free of play and smoothly to the driven element (f/exp Rudder).
• The redesign of our fork servo lever is designed for ruggedness.
• The power dissipation occurs in the middle of the servo gearing.
• The execution of a fork lever effectively prevents misjudged the servo drive output.
• The servo gear will last longer.
• Our Servohebel we manufacture of highly compressed carbon fiber plastic.
• At 300 ° C and under high pressure, the levers get their appearance in hardened steel molds.
• Since this method has similarities with the manufacture of highly stressed components in large aircraft, we have taken it for making our servo arm.
• The result is a high strength component which need not fear comparison with Duralaluminium.
• However, it is lighter and vibration resistant.
• All servo lever are manufactured in Germany using the latest CNC machines.

 

CFK fork servo lever 46mm Futaba

Specifications:

• Gap servo driven ball center to 46mm.
• Fork opening 6mm.
• Fork hole for M3 thread. Weight 3.5g.
• Comes with built-in ball joint
• The high torque of modern digital servos must be free of play and smoothly to the driven element (f/exp Rudder).
• The redesign of our fork servo lever is designed for ruggedness.
• The power dissipation occurs in the middle of the servo gearing.
• The execution of a fork lever effectively prevents misjudged the servo drive output.
• The servo gear will last longer.
• Our Servohebel we manufacture of highly compressed carbon fiber plastic.
• At 300 ° C and under high pressure, the levers get their appearance in hardened steel molds.
• Since this method has similarities with the manufacture of highly stressed components in large aircraft, we have taken it for making our servo arm.
• The result is a high strength component which need not fear comparison with Duralaluminium.
• However, it is lighter and vibration resistant.
• All servo lever are manufactured in Germany using the latest CNC machines.

 

Our main charge leads are constructed from the highest quality materials to ensure that you get the best connection possible every time you charge your batteries.

This unique design serves as both a charging and balancing cable for your 2S battery pack. Connect to your battery with the JST-XH connector, as used in the T-Rex 150. Connect to the charger's main output with 4mm banana plugs, and to the balance port with a standard 2S JST-XH balance connector. Top-quality silicone wire gives you the flexibility you need to easily get everything connected.

Specifications

•   Input Charge Connector: Male 4mm Banana Plug
•   Input Balance Connector: Male 2S JST-XH
•   Output Connector: Female 2S JST-XH
•   Wire Type: 22 AWG Silicone
•   Length: 20CM

SPECIAL Charging cable adapter for blade MCPX, handling 6 batteries .

Insure you use same capacity batteries to charge sufficiently.
produced from 18 awg silicone cables for best quality and low resistance.

Our main charge leads are constructed from the highest quality materials to ensure that you get the best connection possible every time you charge your batteries.

Directly connect to your charger with Banana 4mm bullet connectors, and bare wires to connect any of your desired connectors.
50cm of heavy-duty 12 AWG silicone wire gives you the flexibility to work in any charging setup.

Specifications

•   Input Connector: Male 4mm Banana Plug
•   Output Connector: Bare wires
•   Wire Type: 12 AWG Silicone
•   Length: 50cm

The next V2 generation of our 11 IN 1 Multi- Adapter, This adaptor is "All in one" features 4mm banana plugs that fit most chargers,
And its nicely split into 11 different types of plugs on the other end.

Includes the following connectors:
 

• EC3 gold connector
• T- male deans
• Futaba RX connector
• JR/Spektrum RX
• EC3.5 Connector
• XT90 connector
• JST 2 pin connector
• EC5 gold connector
• XT60 connector
• QS8 connector 4mm wires
• BARE leads- connect any of your..

Take the mess out of your charging with this charger adaptor.

The next generation of our 12 IN 1 Multi- Adapter, This adaptor is "All in one" features 4mm banana plugs that fit most chargers,
And its nicely split into 12 different types of plugs on the other end.

Includes the following connectors:

4mm Silicone Wire with Banana connector towards the charger, splitted to 12 different connectors:

• EC3 gold connector
• T- male mini deans
• Futaba TX connector
• JR/Spektrum TX connector
• Futaba RX connector
• JR/ Spektrum RX connector
• JST 2 pin connector
• EC5 gold connector
• XT60 connector
• 6mm Gold connector
• 4mm Gold connector
• BARE leads- connect any of your..

Take the mess out of your charging with this charger adaptor.

The parallel charge leads allow you to charge up to six battery packs simultaneously.
Constructed from the highest quality materials, they give you the best connection possible every time you charge your batteries.

This unique design serves as both a charging and balancing cable for up to 6 of your 2S battery packs. Connect to your batteries with the connectors, as used in the Blade 130X, Beast UMX or Sbach 342 UMX. Connect to the charger's main output with 4mm banana plugs, and to the balance port with a standard 2S JST-XH balance connector. 10cm of top-quality silicone wire gives you the flexibility you need to easily get everything connected.

Charging adapter XT60 Female to BANANA 4mm female

This extending adapter is very helpful when you need to connect a charging cable ( with Banana 4mm) to Charger which using XT60 connector as Output

Charging adapter XT60 Female to XT30 Male

This extending adapter is very helpful when you need to convert a charging cable XT60 to Battery XT30 plug

Charging adapter XT60 «-» XT30 1,5mm² 30cm

This extending adapter is very helpful when you need to connect a charging cable from XT60 to XT30

These are GREAT working pliers! Soft grip handle, curved end of jaws, spring loaded open.
Not only the best we've used, also the best value!

High quality chrome vanadium steel material , Slip-resistant handle, easy to hold it and operate.
Suits for RC helicopter DIY

Specifications:
Material: Chrome vanadium steel
Size: 16.7*7.5*1cm
Weight: 180g

Deluxe type, ball link plier, multi purpose tool.

These are GREAT working pliers! Soft grip handle, curved end of jaws, spring loaded open. Not only the best we've used, also the best value!

CL-58 5.8GHz Clover-Leaf Spyro Circular Polarized Antenna set, 2 pcs, TX+RX.

Designed for FPV applications.
This offers better looks and excellent protection.
Easy to setup and use standard SMA and RP-SMA connectors.

Description:
SWR≤1.5   
Weight:13g   
Connect: SMA(needle inside) or RP-SMA(hole inside)
Size: TX 8cm,  RX 12cm

POWERZIP strip, 15mm wide, 1meter long, 2mm thick

Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).

There is a red easy-peel liner one one side of the tape. Once the liner is removed, the tape is completely clear & ideal for glass/perspex where an invisible fixing/fastening is required.

Also, ideal for fastening things to any surface, Anti vibration.

 

The best you can allow- CNC tuning Arms set for Logo helicopters. Now you can fly complete Alu CNC head.

Produced in Europe, made from 7075 material, in black anodized finish to fit the existing Mikado logo head.

Those arms will use existing bearings and hardware, all you need will be included in the set.
 

What is the advantage of CNC metal over plastic? Tests reports pointed on mainly those advantages:

•  Less flex , means more precise flying performance.
•  No influence of weather, e.g hot weather will not make the grips softer and vice versa.
•  Silent- been smaller than Plastic, less drag and better flying noise, Efficiency..

Stainless inserts will insure perfect support for blade screws by removing inertia load.

This arm set for Mikado Logo 500-550 series. Set include 2 Grips with Hardware.
Bearing and other items to be used from stock head.

DYI : Make your drone with retractable Arms.D30 CNC Aluminium Folding Arm Joint Fitting (suit for D30mm Tube) W/ up-tilt angle - Auto Edition (Black) V2.

Specification:

• Suitable for 30mm Tube
• 5 degree dip angle to help to enhance stability
• Spring Type Automatic, ease and simple to use!
• DIY necessary! suitable for Quadcopter/Hexacopter/Octacopter
• Material: aluminum alloy
• Color: Black
• Weight: 116 g

CNC Aluminium Fuel line end cap (set of 2)

Made in Korea, from 7075 Alu

CNC Aluminum Quick Release Self-Tightening Prop Adapters for 20-24" props, 10mm hole- set of 2.

If you have large props on your multi copter 20-24" and find it particularly hard to store then the quick release prop adaptors will help, as it allows you to quickly and easily attach and remove your propellers from your multi copter motors without any tools. This new design is 200% lighter than the old version and can now support 20-24 inch props.

These prop adapters are self-locking and you will receive two clockwise and two counter clockwise threaded adapters to use with the corresponding motors. It’s important to make sure that the adapter corresponds to your motor direction.

Suitable for various types of UAV motors using 15mm/M3 or 20mm / M4 three or five hole carbon fiber propellers and motors. The two hole pitches are suitable for different propellers and motors, and can be used in a wider range. The paddle seat distinguishes between color and forward and reverse. Red is forward rotation (motor counterclockwise), Black is reverse rotation (motor clockwise). compatible with commonly used 3 or 5 hole carbon fiber propellers and 98% brushless motors on the market.

Specification:
Direction of rotation: CW / CCW
color: Red and Black(1 pair)
Product Weight: 27g
Screw pitch: 15mm / M3, and 20mm /M10 hole
Material: Space aluminum

CNC Aluminum Quick Release Self-Tightening Prop Adapters for 20-24" props, 4mm hole- set of 2.

If you have large props on your multi copter 20-24" and find it particularly hard to store then the quick release prop adaptors will help, as it allows you to quickly and easily attach and remove your propellers from your multi copter motors without any tools. This new design is 200% lighter than the old version and can now support 20-24 inch props.

These prop adapters are self-locking and you will receive two clockwise and two counter clockwise threaded adapters to use with the corresponding motors. It’s important to make sure that the adapter corresponds to your motor direction.

Suitable for various types of UAV motors using 15mm/M3 or 20mm / M4 three or five hole carbon fiber propellers and motors. The two hole pitches are suitable for different propellers and motors, and can be used in a wider range. The paddle seat distinguishes between color and forward and reverse. Red is forward rotation (motor counterclockwise), Black is reverse rotation (motor clockwise). compatible with commonly used 3 or 5 hole carbon fiber propellers and 98% brushless motors on the market.

Specification:
Direction of rotation: CW / CCW
color: Red and Black(1 pair)
Product Weight: 27g
Screw pitch: 15mm / M3, and 20mm /M4 hole
Material: Space aluminum

CNC Aluminum Quick Release Self-Tightening Prop Adapters for 20-24" props, 6mm hole- set of 2.

If you have large props on your multi copter 20-24" and find it particularly hard to store then the quick release prop adaptors will help, as it allows you to quickly and easily attach and remove your propellers from your multi copter motors without any tools. This new design is 200% lighter than the old version and can now support 20-24 inch props.

These prop adapters are self-locking and you will receive two clockwise and two counter clockwise threaded adapters to use with the corresponding motors. It’s important to make sure that the adapter corresponds to your motor direction.

Suitable for various types of UAV motors using 15mm/M3 or 20mm / M4 three or five hole carbon fiber propellers and motors. The two hole pitches are suitable for different propellers and motors, and can be used in a wider range. The paddle seat distinguishes between color and forward and reverse. Red is forward rotation (motor counterclockwise), Black is reverse rotation (motor clockwise). compatible with commonly used 3 or 5 hole carbon fiber propellers and 98% brushless motors on the market. The hole pitch is 15 / 20mm.

Specification:
Direction of rotation: CW / CCW
color: Black-silver
Product Weight: 27g
Screw pitch: 15mm / M3, and 20mm / M4
Material: Space aluminum

CNC Aluminum Quick Release Self-Tightening Prop Adapters Set - RED (CCW) (1pc)

Mounting the prop on the adapter and the base to the motor and a flick of the prop will thread its self on.

Specification:
Direction of rotation: CW / CCW
color: red
Product Weight: 7g
Screw pitch: 12mm
Screw Size: M3
Material: Space aluminum