eRCmarket

Build your Multi rotor in a NASA way, by experts.

Building a Drone is not a straight forward. Proper installation is a  hassle, especially cheap motors and electronics are very simplified, and require a lot of "Know how".

Non experienced people can take up to hundred hours to build one model and still suffer from bad Vibrations, programming complexes, Tuning, and much more.

We are offering "One stop" service for all your needs.

All the service explained HERE

Using our own components, we have tested over 200 machines, and over 2000 Flying hours, we will deliver :

1-Complete building of the frame, mechanically and electronic wise.

2- All motors and props are Fully Dynamic balanced

3- Controllers (ESC) and Flight controller are fully programmed per your needs

4- With your radio we will set up and make the machine ready to fly

5- Live flight ( Basic setup) demonstration on delivery

Optional: if you need other components such camera, GPS , we can also program all for your custom needs.

Finished machine is ready to fly, without any vibrations, so you can enjoy your Drone flying  and start Working with it for professional or Hobby use.

Customers who located abroad of  Belgium can send us their own radios and we will return all together after proper packaging and flight tests.
Video will be provided to demonstrate the machine in flight

Delivery time is vary.

Extra components Such gimbal, FPV, Telemetry and all extrras over the Drone installation installation can be done on demand, not included in the price. Fees are vary, please contact us for more detailed Quote.

This is the best Insurance to Fly Safe and to keep your Lipo packs goinf Under charge and inflate..

Lithium Battery monitor showing your battery status in use, When the voltage of battery will drop TO SAFE LEVEL, the monitor will start to show it Visually . With the help of this monitor you can detect end of Flight, or any problems in your heli or airplane, and will help you to land safe.

Special Light led seen from long distance.

This product designed to work with ALL lipos 4s 14.8n

Working status as following:

- 14.8 v+ Blue light shines
- 14.8~13.6v Blue light flashs
- 13.6~13.2v, Red light shines
- Below 13.2v, Red light flashing
  From this time, you have around 30 seconds to land ( More then enough time )

This is the best Insurance to Fly Safe and to keep your Lipo packs goinf Under charge and inflate..

Lithium Battery monitor showing your battery status in use, When the voltage of battery will drop TO SAFE LEVEL, the monitor will start to show it Visually and also audible with High DB Piezo buzzer. With the help of this monitor you can detect end of Flight, or any problems in your heli or airplane, and will help you to land safe.

Special Light led and sound will be heard / seen from long distance.

This product designed to work with ALL lipos 6S- 22.2V

Working status as following:

- 22.2 v + Blue light shines
- 22.2~20.4 v Blue light flash
- 20.4~19.8 v, Red light shines
- Below 19.8 v, Red light flashing & Beep
  From this time, you have around 30 seconds to land ( More then enough time )

This is the best Insurance to Fly Safe and to keep your Lipo packs goinf Under charge and inflate..

Lithium Battery monitor showing your battery status in use, When the voltage of battery will drop TO SAFE LEVEL, the monitor will start to show it Visually and also audible with High DB Piezo buzzer. With the help of this monitor you can detect end of Flight, or any problems in your heli or airplane, and will help you to land safe.

Special Light led and sound will be heard / seen from long distance.

This product designed to work with ALL lipos 2S - 7.4v

Working status as following:

- 7.4 v+ Blue light shines
- 7.4~6.8v Blue light flashs
- 6.8~6.6v, Red light shines
- Below 6.6v, Red light flashing & Beep
   From this time, you have around 30 seconds to land ( More then enough time )

Personalize your transmitter with these colorful aluminum switch nuts. Fits  Futaba 12 MZ/FG, 14MZ
Full set including 8 pcs and Removal/installation tool.
You'll notice that the upper rim of the nut is smooth. Some Transmitters have the slots cut in the nuts had sharp corners. If you using to put the fingers between the switches, this got to be very irritating. Those nuts have smooth rim.
Color is Green

24 Bright white circle LED 1.5W DC12V. 140-160LM (1pc)

Specification:
 

• Beam angle: 120°
• Power consumption： 1.7W
• Voltage： DC 12V
• Lumens: 140-160LM
• SMD : 2835 (24 LED)
• Size: 30 (dia) x 40mm (total lenght)

Material:
 

• Composite

 
Instructions:

• High precision CNC cutting
• Light, and more strength.

Specifications:

• Material:High impact Aluminum Alloy
• Weight: 3.3g (approx.)

  Appliable for: RC Quadcopter, helicopter, multicopter,car,boat and airplane,1S-8S / Lipo / Li-ion / Li Mn / Li-Fe battery.

• Use for 1-8s Lipl/Li-ion/LiMn/Li-Fe.
• Voltage detection pricision: 0.01V.
• Unit voltage display range: 0.5V-4.5V.
• Total voltage display range: 0.5V-36V.
• 1S test mode voltage range: 3.7v-30v.
• Low voltage alarm mode for 2-8S.
• Alarm set value range: OFF-2.7V-3.8V.
• When the voltage is below the set value,it will buzzer with red LED light,pre-set value 3.3V.
• Push key which can change the voltage settings and save.
• Size: 3.9cm x 2.4cm x 0.9cm.

Features:

-This product is using for detecting 1S-8S lithium battery
-Detect the voltage of each battery core automatically, support reverse connection protection.
-To know the working state of your battery anytime, protect the battery from overcharge and over discharge.
-The red LED will flash,the buzzer will beeping when the voltage is below the set point.
-The factory default setting is 3.3V, press the button to change the voltage setting, and it will save your current setting automatically.

Carbon Boom support, with CNC caps

Metal Servo arm for heavy duty applications,  Airplanes, cars and Boats.- do not use on helicopters.

Use it where you need extreme reinforcement for your servo, eliminating any slope !

Set including 4 arms with hardware, 40mm length.

GLASS FILAMENT TAPE

Economical filament tape is tough and strong. Contains glass yarn filaments for up to 300 lbs. in tensile strength.

These adhesive tapes feature a longitudinal reinforcement consisting of glass fibre strips. The tape is very strong and has strong adhesive power. It is also extremely resistant to tearing.

Roll of 50 meters, perfect to use on Shock flyers, and other airplanes as a hinges.

Specification:

• Width: 25 mm
• Adhesive power: 7.2 N / cm
• Tear strength: 260 N / m

This block is to use in Robbe helicopters, as third block supporting the main shaft. This will prevent any free flex between the frames.

Helping Hand with Magnifier

Component holder from nickel-plated steel with 2 flexible clip terminals, magnifier (2.5-times) and heavy screw feet.
Helping Hand with Magnifier Big Image

You will have a third hand, e.g. to clamp a board, while you do your work with the component.

• 6 lockable hinges
• Nickel-plated steel
• Heavy screw feet
• Magnifier with 2.5-times enlargement
• 2 clip terminals

• Beam angle: 360°
• Power consumption： 1.5W
• Voltage： DC12V
• Lumens: 140-160LM
• Size: 25x13mm

• Aluminum cage

• Beam angle: 360°
• Power consumption： 2.2W
• Voltage： DC12V
• Lumens: 180-200LM
• Size: 35x19mm

• Aluminum cage

For some servos such as Futaba servo models 9241, 9251, 9253, 9254, 9255, 9256 and other digital servos are not capable of handling 6V, please connect a 5.1V step-down voltage regulator to the rudder servo, or connect it between BEC (ex. RCE-B6X) and the receiver for all servos. It could avoid the servos overloading and damaged.

Specifications

Max continuous current: 5A
Length:104mm
Weight:4.2g

5.8G Helical Antenna (Right) for Receiver SMA

Helical Antenna 12dBi, 5.8GHz, Right hand circular polarization, SMA connector.
The circular polarization directional antenna, high gain, ideal for use in the video receiver when intending long ranges. The antennas are right hand circular polarization. Supplied with SMA connector and including a coaxial cable with SMA or PR-SMA (see spc).
 
Specification:
 

• Frequency: 5.8G
• Sliver plated line and 24K golden interface
• Used for receiver, with three-blade antenna on Tx.
• Suit for video receiver
• Right Hand Circular Polarization
• Interface: Please check pictures (please note the connector type you need when place an order) 

Package:
 

• 5.8G Helical Antenna x 1
• 15cm coaxial cable x 1

Made from stainless steel, this extremely strong and straight tubes can be used to create your own tail drive.Those tubes made from special stainless tubes, they have a bending tolerance of 0.01mm /1 meter.Supplied as a Piece of 1 meter long

FF9/ 9C Transmitter SWITCH NUTS

Full set including 8 pcs and Removal/installation tool. For Futaba FF9/9C
You'll notice that the upper rim of the nut is smooth. Some Transmitters have the slots cut in the nuts had sharp corners. If you using to put the fingers between the switches, this got to be very irritating. Those nuts have smooth rim.
The colors are just a bonus

ABS M3 Round Standoff , Non-threaded Spacer 3,5,6,8mm

made for M3 screws, non threaded , size is 3.2mm(ID), 7mm(OD)

Set of 10 pcs

Sizes avaliable( THICKNESS/HEIGHT)

3/5/6/8mm long

This fast mounting set was designed for most on market 500~800 class helicopters with M3 screw holes canopy mounts. WHITE.

Specifications:

• Base length is 14mm
• Add the Nylon Collars to adjust to 20mm, 22mm, 24mm,
• Cut the Nylon Collars to require length.
• Canopy Rubber Grommet openings diameter 7.2~7.5mm

Includes:

• 2x Fast Mounting Canopy Mount
• 2x M3x20 Set Screw
• 2x M3x16 Set Screw
• 2x Rubber Grommet
• 2x 7x6MM Nylon Collar
• 2x 7x8MM Nylon Collar
• 2x 7x10MM Nylon Collar

Best way to properly fasten your battery packs is to use Self Adhesive Velcro on the battery (loop side) and Self adhesive Velcro (hook side) on battery tray.
Also works well in attaching Receivers as it absorbs some of the vibrations.
Set of Both sides, Hook and Loop, 1 meter each. 25mm wide,Black color

Adjustable Digital Soldering Station Esd 48W With Accessories

The ZD 931 Soldering Station is ideal for hobby electronics, school, workshop, service and labor.
Heat Settings are using the up/down button in 1 ° and 5 °C increments.
The soldering iron is connected using the 5 pin connector on the docking station.
With Soldering Iron Stand and viscose cleaning sponge in the drawer/Compact, robust and protective insulation housing/Station and COB HOLDERS Getrennt position/Rapid switching the soldering tip
Large LCD display with and is value/Temperature Control with electronic sensor/Quick heating time thanks to generously dimensioned power supply; high-performance 48 W SOLDERING IRON FOR A WIDE RANGE OF USES
Temperature Range from 145 and 450 °C/Optical and acoustic error message at malfunction/Surge Protection

Technical Data:

• Operating Voltage: 230 V (220 – 240 V), 50 Hz
• Soldering Iron Power: 48 W
• Device mains fuse: T 1 A/250 V
• 150 °C – 450 °C Temperature Range in 1 °C increments
• Display precision: 5%
• LC Display with the 3 1/2 Points
• Max. Power consumption: approx. Power
• Average Service Life of the heating element in soldering iron: approx. 500 hours
• Cable Length Between piston and plug: 1100 mm
• Dimensions (W x H x D): 185X100X150 MM
• Weight: Approx. 2.0 kg

Box Contents:

• Soldering Station ZD 931 with soldering iron holder and drawer with cleaning sponge
• Helping Hand with Magnifying Glass
• DESOLDERING PUMP
• Solder Wire, 1 mm, 10g in dispenser
• 2x Brush/Scraper 

AeroSIM RC Training Simulator, this is the latest version and the download will update it to always last version avaliable

This high quality RC flight simulator includes a CD with software and user manual in electronic format, and a USB interface with an adapter to fit the transmitter of your choice.

The USB interface is fitted with a 3.5 mono jack that can be directly used with JR/Spektrum/HitecAurora/Turnigy/GraupnerMX. An adapter is required for other transmiters (sold separately), consisting on a short cable with a female 3.5 mono jack on on one end, and the right type of connector for the particular transmitter on the other end. Available connectors include: Futaba Square Plug, DIN6 for Futaba Round Plug and Hitec, Multiplex (DIN5, compatible with DIN7 and DIN8), Graupner with Trainer Socket (jack 3.5mm stereo), and ESky/WFly/Storm (minDIN4).

Upgrade policy:

The latest full version of the software can be freely downloaded from the download page at www.aerosimrc.com. Try it out before you buy it!!!

Without the original USB cable, the flying time is limited to two minutes after which the model stops flying and a message inviting to purchase the simulator is displayed.

The upgrade policy is that all future software updates, including new functions, models and scenarios will be free to download.

FPV features:

The simulator is quite popular among FPV enthusiasts for its unique FPV features. The on-board FPV Camera in all models can be controlled from the transmitter (or even from a Head Tracker), and several types of OSD present the GPS and flight data in a realistic way. There are also customers interested in practicing FPV over their actual flying site, and the simulator includes a Scenario Generator to build new scenarios from satellite imagery, captured, for instance, from Google Earth.

Multicopter Models:

It also includes several MikroKopter models that have been tested by the creator Holger Buss, and MK users are finding very attractive the simulator in order to protect their investment by learning to fly them first in the simulator. Also the GAUI 330X-S is included.

Video:

• Training Programs
• There are two Training Programs: (1) Airplane, and (2) Helicopter/Multicopter.
• The Training Programs are designed for those with no experience at all on RC, and we are getting very good feedback from the users who try them.

Minimum Requirements:

• Pentium III or compatible at 1GHz
• Graphic Card with at least 32MB RAM with OpenGL driver.
• 512 MB RAM
• 200MB hard disk space
• CD-ROM Player
• Sound card compatible with DirectX
• Free USB port to connect the transmitter
• Compatible Radio Transmitter Futaba/Sanwa/Hitec/Multiplex/JR/Spektrum with trainer connector.
• Windows 7 (32 and 64 bits), Windows Vista, Windows XP or Windows 2000

Recommended Requirements:

• Pentium 4 or compatible at 2GHz
• Graphic card ATI or NVIDIA with 128MB and with OpenGL driver

When it comes to brushless gimbals whether you are a pro-cinematographer or a multi-rotor hobbyist there is no question AlexMos controllers with Basecam (SimpleBGC) has set the mark in the industry for performance, ease of use and a host of user definable options.\

3 AXIS controller set.

Align Metal Head Stopper t-rex 450 PRO#H45018

INCLUDED: Metal head stopper x 1
Socket screw x 1(M2x5mm)

Align T-Rex 700XN Super Combo with Engine, Muffler & FREE Fuel 4x5 Litres!

Content:

• T-REX 700XN Dominator Super Combo NEW 2018 model - RH70N11X
• 1 x FREE box of 4x5 Litres Optifuel OPTIMIX-20 or 25SLV Ready fuel

included

Engine:

• OS 105 HZ

Muffler:

Stock dependent( power boost, etc)

Not included: FBL unit, radio, recevier, bec, battery

Curved tip specially designed to cut easily different materials, such as polycarbonate and more.

These can also be used for airplane canopies, helicopter windshields and other plastics.
Strong plastic handle for comfort and control.
Lazer made Stainless steel cutting blades

Boom Servo Mounting set ,for Different Helis (See size options) choose your Boom diameter .
Cnc made. Hardware included

Fits for Booms with diameter

21mm
22mm
24mm

Mount your servo on the side or on wing of the heli, airplane and other applications.
CNC made, very light construction.

Material: aluminium 6061-T6 (anodized)
Weight: 20g
Servo: FUTABA, HITEC, JR, SAVOX
Servo not included

Avaliable in Red or Blue( Stock depending)

Aluminium Blade holders fit Millenium, Nova, Cuatro, Dyna-x tail rotors, and increases the precision and rigidity of the tail, it also looks superb. Contents: Set of 2 blade holders

Futaba - Savox 25T Servo Horn/ Aluminum Alloy Locking Reinforced Servo Arm

available in Black

Set inclusive 1pcs Arm Black

Futaba - Savox 25T Servo Horn/ Aluminum Alloy Reinforced Servo Arm

Set including : 1 servo arm

Futaba - Savox 25T Servo Horn/ Aluminum Alloy Reinforced Servo Arm

available in Red/Black and Gold/Black

Set inclusive -1pcs (choose your color)

Aluminum CNC Magnetic Transmitter Stand - Orange

• Fits most transmitter with a flat surface at the back (45mm30mm flat area)
• Easy installation with double side tape
• To creat a angled control panel for setting up your models
• Auto magnetic folded stand

Contents:

• Magnetic Transmitter Stand (Orange)x1
• Double side tape x2
• Hinge shaft x1
• M23 set screws x2
• Carbon fiber stand plate x1
• M23 round head screw x2