Multi-Rotor Frames

Align M470L Multicopter Quadcopter Super Combo

After times of researches and development, Align R&D team dedicated all of its technical expertise and experiences into the development of a brand new aerial photography platform, to give birth to the brand new.

Moisture resistant shape at the pinnacle of power and beauty, industrial and structural design. Encompass stability control system, features light weight, strong payload, and long flight time.
Superior in both high speed agility and static stability, this multi-purposed professional multicopter exceeds in all areas such as aerial photography or as leisurely sports flyer; yet its light weight allows for easy transport anywhere.

Align G2 gimbal is specially designed for GoPro. G2 gimbal features advanced control system with superior computational power and the high precision brushless motors provide excellent agility and stability as well as powerful functionality.
Support the use of satellite receivers and S.BUS/X.BUS receivers and supports programmability through PC interface, or connectivity to iOS/Android smartphones through Bluetooth. Enable you to enjoy aerial photography.

Specification

• Airframe Diameter: 710mm
• Height: 266mm
• Main Blade Length: 179mm
• Main Rotor Diameter: 391mm
• Flying Weight(without battery): 2500g

Standard Equipment

• Multicopter Canopy x 1
• 7 Inch Main Rotor x 4 Sets
• External Status LED x 1
• BL4213(370KV) Brushless Motor x 4
• Multicopter Brushless ESC x 4
• PCU Power Control Unit x 1
• APS-M Multicopter Controller x 1
• Multicopter GPS Sensor x 1

APS-M Flight Control System Specification

• Input Voltage:DC 4.5~8.4V
• Operating Current Consumption:<250mA @ 4.8V
• Operating Frequency：400Hz
• Operating Temperature：-20℃~65℃
• Hovering Precision (Depending on Satellite Status)：Horizontal ±1m Vertical ±1m
• Maximum Flight Speed：Horizontal 15m/sec Vertical 6m/sec
• Maximum Altitude Restriction：700m(2297ft) above the takeoff point
• Maximum Angular Speed：
• Aileron 115°/sec
• Elevator 115°/sec
• Rudder 145°/sec
• Maximum Tilting Angle：30 degrees
• Supports External Peripherals："G2/ G3 Gimbal、OSD+FPV Video Transmitter "
• Supports Multicopter Configurations："4 rotors +, 4 rotors X, 6 rotors +, 6 rotors X, 8 rotors +, 8 rotors X."
• Dimension：49x34.3x20mm

PCU Power Control Unit

• Input Voltage：13.2V~25.2V(4S~6S Li-Po)
• Operating Frequency：500KHz
• Dimension：62x35x26mm

BL4213 Motor 370KV(RPM/V)

• Input Voltage：DC 22.2V
• Max Continuous Current：25A
• Max Continuous Power：550W
• Stator Arms：12
• Magnet Poles：14
• Dimension/Weight：4x52x33mm / 185g

Motor ESC

• Input Voltage：13.2V~25.2V(4S~6S Li-Po)
• Max Continuous Current：40A
• Dimension：74.2x27x12.7mm

• It`s made from extra strong patented technology carbon fiber plates and tubes, using our own technologies and equipment.
  It`s build to provide very smooth and stable flight with extra-heavy up 5kg payloads .
• This frame is foldable - it`s very comfortable for transport . You`ll be need to release 12pcs of wing nuts to fold the motor arms and landing gears to put your copter into the storage place.
• Two big li-po shelves allow the use of two-four LiPos to increase flying time and make their replacement easy and in correct CG.
• The protection cage will keep the copter`s electronic equipment in cases of overflips, protecting expensive electronics.
• Ultimate camera mount adaptor plate is specialy designed to reduce vibration on camera . It`s compatible with all camera mounts .
• The holes to mount standard controllers and also the MikroKopter electronics are already foreseen on the centerplate, as the ones necessary for the distribution board with the speed controllers.
• This machine including a large foldable landing gear (350mm of clearance).
• The frame is delivered partially assembled, so building is faster and easier.
• Diameter of the frame +- 1100mm.

This is an Extended hexacopter combo set - main frame, landing gear and camera mount. Size is +- 900mm. Frame complete weight ~960gr.

This product can be supplied as Frame only, with landing gear, and with camera mount. all per customer choice.

Main Highlights!

=Produced In Europe, with highest Grade Carbon fiber for Maximum strength and performace.

=The 900 frame can be equipped in each arm with 1 or 2 motors, e.g 6 motors and if added also pusher motors, it can be 12.

=Max pick up weight is up to 5.5 kg ( nett Pickup weight, excluding the own weight of the frame/electronics)

=Foldable Arms, Landing gear, camera mount, for easy transportation and carriage. can fit all in Supermarket Bag

Technical Data

- main frame`s weight ~620 gr,
- size between motor axes ~900mm
- equipped with Dual-battery slider system ( Recommended 2 x 3s 5000 lipo), two battery mount plates are included.

-- camera mount is is producing in two options :1- compatible with pocket-size cameras - like Canon Ixus ,SONY and others pocket size. and second - for GoPro.

Any of mounts are equipped with two servos TGY930. Every Axe supported by Dual ball bearings
Working angles : ailerons +-30 degrees, elevator -90 /+10degrees.
Camera mount`s weight ~230gr.

- Sliding battery trays, for easy battery replacement.

-Landing gear, Height is 205mm, width between skids = 400mm. Weight ~110gr.

All other electronic parts/ Motors and camera are not included in the set

New Innovative design Multicopter- Spy, Produced in Belgium. this machine is 600 or 750 or 900mm wide(choice)

This product is a Y6 Combo,means you have 6 motors on the machine.This setup is made for 4S lipos, 6S setups also possible as option

Combo delivered with the following:

          Sky hero Spy kit

• 6 x Avizar MC3536 710kv or 380kv
• 6 x ESC 40A SimonK programmed, Special size to enter the SKY HERO tube arms
• 6 x Fully balanced props (choice of Graupner E, APC/ MR/ WOOOD ) size of prop will be delivered based on machine size.
• 1 x Power distribution Board or Distribution wire..
• 1 x Canopy of choice, stock dependent.

To complete the combo you will need your radio, Flight controller, and Lipo battery.

* If 6s setup chosen, 380 kv will be delivered, together with larger propellers - to suit 6S setups.

- Build your Multi rotor in a NASA way, by experts.

Building a Drone is not a straight forward. Proper installation is a  hassle, especially cheap motors and electronics are very simplified, and require a lot of "Know how".

Non experienced people can take up to hundred hours to build one model and still suffer from bad Vibrations, programming complexes, Tuning, and much more.

We are offering "One stop" service for all your needs.

Please ask us for this option cost.

New Innovative design Multicopter- Spyder, Produced in Belgium. this machine is 700 or 850 or 1000mm wide(choice)

This product is a X8 Combo,means you have 8 motors on the machine.This setup is made for 4S lipos, 6S setups also possible as option.

Combo delivered with the following:

           Sky hero Spyder Frame kit

• 8 x Avizar MC3536-710KV(4s) or 380KV (6s)or T-motor motors
• 8 x ESC 40-60A SimonK 2-6S lipo, programmed, Optimized and size will enter the arms of Spyder.
• 8 x Fully balanced props 11-14" ( choice of Graupner E, APC, Wood ) size of prop will be delivered based on machine size.
• 1 x Power distribution Board 80amp
• Canopy of choice( Stock dependent)

To complete the combo you will need your radio, Flight controller, and Lipo battery.

* If 6s setup chosen, 380 kv will be delivered, together with larger propellers - to suit 6S setups.

Movie showing MC3536 motors and 40A esc

- Build your Multi rotor in a NASA way, by experts.

Building a Drone is not a straight forward. Proper installation is a  hassle, especially cheap motors and electronics are very simplified, and require a lot of "Know how".

Non experienced people can take up to hundred hours to build one model and still suffer from bad Vibrations, programming complexes, Tuning, and much more.

We are offering "One stop" service for all your needs.

Please ask us for extra charges

This is a Y6 Combo set with all you need to complete( NO RADIO/.LIPO) included, please note that the frame is Pre-built, and components are NOT installed.

We deliver a quality controller which is perfect to fly and train, and can be expanded with GPS and other add ons.

Frame is made from Carbon. This machine is produced in Europe. Same frame can be found under other brands for higher cost.

Included:

-1 x MWC or KK flight controller
-6 x BL Motors Avizar suitable for this frame configuration.
-6 x APC or equal props suitable for this configuration
-6 x 20-30 Amps Speed controllers( For expert-possible to have programmable)
-1 x Led strip for easy orientation
-6 x Prop Adaptor

This product can be supplied as Frame only, with landing gear, and with camera mount. all per customer choice.

Main Highlights!

=Produced In Europe, with highest Grade Carbon fiber for Maximum strength and performance.

=The 650 frame can be equipped in each arm with 1 or 2 motors per Arm.

=Max pick up weight is up to 2.9 kg ( net Pickup weight, excluding the own weight of the frame/electronics)

=Foldable Arms, Landing gear, camera mount, for easy transportation and carriage. can fit all in Supermarket Bag

Technical Data

- main frame`s weight ~420gr,
- size between motor axes ~650mm
- equipped with single-battery slider system (it`s possible to fit till to 4s 6000mAh lipo), two battery mount plates are included.

-- camera mount is is producing in two options :1- compatible with pocket-size cameras - like Canon Ixus ,SONY and others pocket size. and second - for GoPro.

Any of mounts are equipped with two servos . Every Axe supported by Dual ball bearings
Working angles : ailerons +-30 degrees, elevator -90 /+10degrees.
Camera mount`s weight ~230gr.

- Sliding battery tray, for easy battery replacement.

-Landing gear, Height is 300 mm, width between skids = 400mm. Weight ~110gr.