Motor Accessories

Accessories for Brushless motors, mounts, prop adaptors, and more

Page of 2
3mm shaft

3mm shaft

3mm shaft for ALU gear box

€1.27

Inc. VAT
Quantity
Brushless Motor Mount

Brushless Motor Mount

Brushless Motor Mount : Out-runner

€6.00

Inc. VAT
Quantity
Bullet spinner cone for FPV motor CCW (Silver)

Bullet spinner cone for FPV motor CCW (Silver)

Bullet spinner Holder for FPV motor CCW (Silver)

fits most 1806-2208 motors with 5mm treads

€3.50

Inc. VAT
Quantity
Bullet spinner cone for FPV motor CW (Black)

Bullet spinner cone for FPV motor CW (Black)

Bullet spinner Holder for FPV motor CW (Black)

fits most 1806-2208 motors with 5mm treads

€3.50

Inc. VAT
Quantity
Carbon Prop Cover T-Motor  for MN18XX, MN22XX

Carbon Prop Cover T-Motor for MN18XX, MN22XX

Tiger Motor - Carbon Prop Cover - for MN18XX, MN22XX

€2.00

Inc. VAT
Quantity
Gear box

Gear box

Gear box-ratio 3.75:1 / 5.43

€29.00

Inc. VAT
Quantity
Gearbox motor  mount

Gearbox motor mount

Gearbox motor mount

€15.00

Inc. VAT
Quantity
Heat Shrink 6.4mm, 2:1 rate, 1 meter, red or black

Heat Shrink 6.4mm, 2:1 rate, 1 meter, red or black

Avaliable in Red or Black for easy wires identification.
made in Germany, Shrink up to 50% ( 2:1) of its size.excellent for any electric application.
Use in places where isolation needed. Price per 1meter

Size- 6.4mm.

€3.00

Inc. VAT
Quantity
Heat Shrink 6mm with Glue inside, 3:1 rate, 1 meter BLACK

Heat Shrink 6mm with Glue inside, 3:1 rate, 1 meter BLACK

Heat Shrink 6mm with Glue inside, 2:1 rate, 1 meter BLACK

Made in Germany, Shrink up to 75% ( 3:1) of its size.excellent for any electric application.
Use in places where isolation needed. Price per 1meter

Size- 6mm.

€3.00

Inc. VAT
Quantity
Heat Shrink 8mm with Glue inside, 4:1 rate, 1 meter BLACK

Heat Shrink 8mm with Glue inside, 4:1 rate, 1 meter BLACK

Heat Shrink 8mm with Glue inside, 2:1 rate, 1 meter BLACK

Made in Germany, Shrink up to 80% ( 4:1) of its size.excellent for any electric application.
Use in places where isolation needed. Price per 1meter

Size- 8mm.

€4.50

Inc. VAT
Quantity
Heat Shrink 9mm, red or black, 2:1 shrinking, 1 meter

Heat Shrink 9mm, red or black, 2:1 shrinking, 1 meter

Avaliable in Red or Black for easy wires identification.
made in Germany, Shrink up to 50% of its size.excellent for any electric application.
Use in places where isolation needed.  Price per 1meter

Size : 9mm

€3.00

Inc. VAT
Quantity
Heat Shrink Transparent clear 12.7 mm, 2:1 rate, 1 meter

Heat Shrink Transparent clear 12.7 mm, 2:1 rate, 1 meter

Heat Shrink Transparent clear 6.4mm, 2:1 rate, 1 meter
made in Germany, Shrink up to 50% ( 2:1) of its size.excellent for any electric application.
Use in places where isolation needed.

  • Size- 12.7 mm
  • 1 meter
  • Transparent

€3.00

Inc. VAT
Quantity
Heat Shrink Transparent clear 6.4mm, 2:1 rate, 1 meter

Heat Shrink Transparent clear 6.4mm, 2:1 rate, 1 meter

Heat Shrink Transparent clear 6.4mm, 2:1 rate, 1 meter
made in Germany, Shrink up to 50% ( 2:1) of its size.excellent for any electric application.
Use in places where isolation needed.

  • Size- 6.4mm.
  • 1 meter
  • Transparent

€3.00

Inc. VAT
Quantity
Heat Shrink Tube 2.4mm, 1meter long, Red or black

Heat Shrink Tube 2.4mm, 1meter long, Red or black

Heat Shrink 2.4mm, can shrink up to 50%( 2:1)  to use in servo wires,extensions , batteries, and any other application
Pack of 1 meter
Color black or Red

€2.50

Inc. VAT
Quantity
Heat Shrink Tube 3.2mm, 1meter long, Red or black

Heat Shrink Tube 3.2mm, 1meter long, Red or black

Heat Shrink 3.2mm, can shrink up to 50%( 2:1)  to use in servo wires,extensions , batteries, and any other application
Pack of 1 meter
Color black or Red

€2.50

Inc. VAT
Quantity
HK-4525 Shaft Kit XL (6mm 55mm) Mikado Logo 700

HK-4525 Shaft Kit XL (6mm 55mm) Mikado Logo 700

HK-4525 Shaft Kit XL (6mm 55mm) Mikado Logo 700 special.

The Scorpion HK-4525 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4525 series Scorpion Helicopter Motors.

This extended shaft for the HK-4525 series motors measures 10mm in diameter, and is 112.3mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

€29.90

Inc. VAT
Quantity
HKII-42 & HK-45 Series Bearing Maintenance Kit

HKII-42 & HK-45 Series Bearing Maintenance Kit

The Scorpion HKII-42 & HK-45 Series Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HKII-42 & HK-45 Series Motor.

€24.99

Inc. VAT
Quantity
KNY motor turbo Cooler by Kenny Ko

KNY motor turbo Cooler by Kenny Ko

This motor cooler from Align World Champion Helicopter pilot ‘Kenny Ko’ is designed to cool down the 700/800 class motors between flights.

Note this requires a 3 Cell Lipo with a JST style connector

€31.00

Inc. VAT
Quantity
Large Heat Shrink( heatshrink) PVC, flat ,Made in germany

Large Heat Shrink( heatshrink) PVC, flat ,Made in germany

Thise Shrink is to use as a holding over a battery pack, or wrapping over larger items, like receiver pack and more.

Sizes (flat) avaliable:

33 mm fits diameters from 15 till 21 mm
40 mm fits diameters from 17 till 25 mm
69 mm fits diameters from 21 till 42 mm
90mm fits diameters from 25 till 60 mm
95 mm fits diameters from 32 till 69 mm
115 mm fits diameters from 33 till 75 mm
120 mm fits diameters from 37 till 78 mm
165 mm fits diameters from 80 till 115mm

included PVC of 1 meter

€3.00

Inc. VAT
Quantity
Outrunner accessory set D28

Outrunner accessory set D28

Outrunner accessory set D28, Prop mount, motor mount, etc..
The set is suitable for motor shaft diameters of 3.17 mm.

€7.50

Inc. VAT
Quantity
Pinion gear

Pinion gear

Pinion gear for ALU Gear box 10/12/14/16T

€4.00

Inc. VAT
Quantity
Prop Adaptor 4mm

Prop Adaptor 4mm

Machined from High-Quality Aluminum bar stock, it is designed to fit on a 4mm motor shaft, and has a 6mm threaded prop shaft.

€5.00

Inc. VAT
Quantity
Prop Adaptor 5mm

Prop Adaptor 5mm

Machined from High-Quality Aluminum bar stock, it is designed to fit on a 5mm motor shaft, and has a 8mm threaded prop shaft.

€5.00

Inc. VAT
Quantity
PropSaver

PropSaver

Prop adaptor which also act as a Saver. Suiatable for 2.3/3/3.2/4mm shafts

€5.00

Inc. VAT
Quantity
Scorpion HK-3026 Bearing Maintenance Kit

Scorpion HK-3026 Bearing Maintenance Kit

The Scorpion HK-3026 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HK-30 Series Motor.

€19.99

Inc. VAT
Quantity
Scorpion HK-40 Motor Bearing Kit

Scorpion HK-40 Motor Bearing Kit

Scorpion HK-40 Motor Bearing Kit.

In order to keep your motor in top running condition, you need a good set of bearings. Occasionally, after a crash or landing in the dirt, the bearings can become damaged and need to be replaced.
The Scorpion HK-40mm Motor Bearing Kit includes a pair of original equipment replacement bearings to fit the Scorpion HK-40 & HKIII-40 Series motors.(Except HK-4015)

Please note, the bearings are an exact fit into the motor housings, so they do fit snugly. When removing the old bearings, you may need to gently tap them out. However, when installing the new bearings, do not tap them in with anything, as this can dent the ball races and ruin the bearings.
When installing ball bearings they need to be pressed in by the outer part of the race. Never apply pressure to the inner race, as this can damage the bearing and lead to premature failure.

€8.50

Inc. VAT
Quantity
Scorpion HK-5020 Motor Shaft Kit (6mm 43mm)

Scorpion HK-5020 Motor Shaft Kit (6mm 43mm)

The Scorpion HK-5020 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-5020 series Scorpion Helicopter Motors.

The shaft for the HK-5020 series motors measures 10mm in diameter, and is 84.6mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

€42.99

Inc. VAT
Quantity
Scorpion HKII-2221 Bearing Maintenance Kit

Scorpion HKII-2221 Bearing Maintenance Kit

The Scorpion HKII-2221 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HKII-22 Series Motor.

€19.99

Inc. VAT
Quantity
Scorpion HKIII-4025 Shaft Kit XL (6mm)

Scorpion HKIII-4025 Shaft Kit XL (6mm)

The Scorpion HK-4025 & HKIII-4025 series motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4025 & HKIII-4025 series Scorpion Helicopter Motors.

This shaft kit is for the HK-4025 & HKIII-4025 series motors that used in newer T-600 Heli. It measures 8mm in diameter, and is 88.5mm in length. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 6mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

Included in the Box:

  • HKIII-4025 Motor Shaft Kit (6mm) -XL x1
  • Washer x 1
  • C-Clip x 2

€18.00

Inc. VAT
Quantity
Scorpion HKIII-4035 Bearing Maintenance Kit

Scorpion HKIII-4035 Bearing Maintenance Kit

The Scorpion HK-4035 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HK-40 & HKIII-40 Series Motor, except the HK-4015 Series.

€19.99

Inc. VAT
Scorpion motor  Shaft HKII-4530 8mm 55mm

Scorpion motor Shaft HKII-4530 8mm 55mm

The Scorpion HK-4530 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4530 series Scorpion Helicopter Motors.

The shaft for the HK-4530 series motors measures 10mm in diameter. The pinion end of this shaft is ground down to 8mm to allow the user to install 8mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

€36.00

Inc. VAT
Quantity
Scorpion motor  Shaft HKII-4540 8mm 55mm

Scorpion motor Shaft HKII-4540 8mm 55mm

The Scorpion HK-4540 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4540 series Scorpion Helicopter Motors.

This extended shaft for the HK-4535 series motors measures 10mm in diameter, and is 127mm in long. The pinion end of this shaft is ground down to 8mm to allow the user to install 8mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

€35.00

Inc. VAT
Quantity
Scorpion Motor Bearing Lubrication Kit (23ml) (Alu cap)

Scorpion Motor Bearing Lubrication Kit (23ml) (Alu cap)

The Scorpion Motor Bearing Lubrication Kit will help you maintain the bearings in your Scorpion brushless electric motor. Today's brushless motors, especially the helicopter motors, can be pretty hard on the bearings. In an average flight, the motor in a 450 size helicopter spins around almost a quarter million times! Without proper lubrication, the balls in the bearings can wear out quickly, leading to premature failure. At these speeds, the oil can get thrown out of the bearings in as little as 10-15 flights. Once the bearings loose their lubrication, they can heat up and wear out very quickly. A small drop placed on each bearing about once every 10-15 flights is enough to maintain proper lubrication to insure the longest possible life for your motor bearings.

The oil included in this kit contains everything necessary to keep your motor bearings in top condition. The specially designed oil not only lubricates, it also bonds to the metal parts, displaces moisture and prevents corrosion to extend the life of your motor bearings.

The oil is safe for use on Acrylics, Polyester, Nylon, Vinyl, Delrin, Teflon, Formica, Polyethylene and Polypropylene. It is also safe on most painted surfaces. There is no visible effect on Buna-N, Viton or Neoprene rubber products, so it is safe around most fuel lines, O-rings and other rubber products.

The Scorpion Motor Bearing Lubrication Kit contains a 23ml bottle of bearing lubricant, a leak-proof twist-on cap, and a needle point applicator (19.5mm in length, 1.3mm in diameter) with protective cover. You have to remove the screw inside the Aluminum cap before use.

€9.99

Inc. VAT
Quantity
Scorpion Motor HK-4525 Shaft Kit XL (6mm 50mm)

Scorpion Motor HK-4525 Shaft Kit XL (6mm 50mm)

The Scorpion HK-4525 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4525 series Scorpion Helicopter Motors.

This extended shaft for the HK-4525 series motors measures 10mm in diameter, and is 104mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

€29.00

Inc. VAT
Quantity
Scorpion motor HK-4530 Shaft Kit XL (6mm 37mm)

Scorpion motor HK-4530 Shaft Kit XL (6mm 37mm)

The Scorpion HK-4530 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4530 series Scorpion Helicopter Motors.

The shaft for the HK-4530 series motors measures 10mm in diameter, and is 100mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

€38.00

Inc. VAT
Quantity
Scorpion motor HK-4530 Shaft Kit XL (6mm 55mm) Logo 700

Scorpion motor HK-4530 Shaft Kit XL (6mm 55mm) Logo 700

The Scorpion HK-4530 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4530 series Scorpion Helicopter Motors.

This extended shaft for the HK-4530 series motors measures 10mm in diameter, and is 117mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

€38.00

Inc. VAT
Quantity
Page of 2