Canopy Accessories

This retractable undercarriage kit has been developed specifically for the Bell 222 and Airwolf fuselage kit.
The tricycle undercarriage is operated by a single or double central servo, and the retract units lock mechanically at both end-points.

This set fit 30-60 size fuselages, Rubber Wheels Not included ( Original from the kit should be used)

Picture

Designed for the serious 3D pilot who demands a failproof grommet system that can withstand hundreds of flights without having to worry about canopy grommet failure.

This 3pc system is made to work with on any Nitro Helicopter that uses the RCBooya Quick Release Canopy Mount and has a option to enlarge the canopy holes to 7/16 diameter.

IMPORTANT

Made for use with canopies that measure 1mm in thickness

Kit Includes

4- Booya Tuff ™ Snap Grommets

4- Fuel Proof VITON ™ O-Rings

Installation Instructions

Enlarge the canopy grommet holes to 7/16 diameter

Take apart the two halves of the grommet

Place CA onto the grommet area that comes into contact with the canopy

Install into canopy,white recess on the outside of the canopy,0-ring to the inside of the canopy

Snap the two halves togather and allow CA to setup

Install Quick Release Pin into Booya Tuff ™ Grommet

ENJOY !

Canopy Clips 10pcs

Protect your canopy edges, or use it as wire protection against carbon frames, use it combined with fuel tanks.. and much more.
this Strip including U shape EPDM. the profile is U shape and its 1.2mm wall thick, fits perfectly 1-2 mm frames.
See images for exact dimensions and sizes.

Protect your canopy edges, or use it as wire protection against carbon frames, use it combined with fuel tanks.. and much more.

• this Strip including round U shape EPDM.
• the profile is U shape and its 5.5mm diameter, with cut to fit perfectly 1-2 mm frames.
• See images for exact dimensions and sizes.

Edge 'U' protector transparent rubber (1 M)

For carbon sheets from 1.0mm - 2.0mm.

Edge protector for carbon sheets from 1.0mm - 2.0mm.

Goblin 380/420 MAGNETIC QUICK RELEASE CANOPY SET

Expedites the installation and removal of the canopy

Includes:
 

• Canopy possition x 2pcs
• Magnet Canopy Pin x 2pcs

Use for:

Goblin 380/420
 

4- Fuel Resistant Anti Vibration Pads w/3M™ Adhesive Heli Team Tip: To protect the adhesive from fuel add a band of CA around the outside of the anti vibration pad. WORKS GREAT !

Scale Cockpit set for Blue Thunder fuselage Fuselage

Quick Release Canopy system mount features a custom locking push/pull pin design made to fit your Helicopter

Standoff is made from 6061-T6 Aluminum ,Silver Anodized
Quick Release pin is made from all stainless steel construction and is designed to stay connected to the canopy when not in use

Kit Includes:

• Quick Release Pin x 2
• Quick Release Standoff x 2
• Preinstalled Grommets x 2
• ABS standoff 3mm x 2
• ABS standoff 5mm x 2
• ABS standoff 6mm x 2
• ABS standoff 8mm x 2
• Screws M3 x 2

Standoff length is 30mm, supplied ABS spacers allow to adapt to different lengths.

NOTE: Use of this kit required you to increase the canopy mounting hole

Magnetic Canopy Mount in Black

Pack - 1 x Magnet, 1 x Washer, 2 x Fitting Screws

Ultra Quick Fit / Release Magnetic canopy mounting system for the Trex 600 NITRO

This new canopy mounting system uses ultra powerful Neodymium N42 rare earth magnets to secure the canopy. Each pair of magnets provide approx 2kg (4.5lbs) of retaining force per side, a central locating pin ensures a positive fit that is super quick both to fit and release.

The kit comprises of two pylons each fitted with an N42 magnet which attach to the heli chassis and two smaller N42 mag mounts that attach to the canopy with a pair of flush fit finishers. Once fitted, there are no screws to undo, no clips to take out and no pins to depress....simply offer up the canopy and let the magnets do the rest, removal is a simple case of pulling away from the mounts...fitting and removal in seconds !

For use with original Align canopy grommets. Black color

Ultra Quick Fit / Release Magnetic canopy mounting system for the Trex 600 Electric

This new canopy mounting system uses ultra powerful Neodymium N42 rare earth magnets to secure the canopy. Each pair of magnets provide approx 2kg (4.5lbs) of retaining force per side, a central locating pin ensures a positive fit that is super quick both tp fit and release.

The kit comprises of two pylons each fitted with an N42 magnet which attach to the heli chassis and two smaller N42 mag mounts that attach to the canopy with a pair of flush fit finishers. Once fitted, there are no screws to undo, no clips to take out and no pins to depress....simply offer up the canopy and let the magnets do the rest, removal is a simple case of pulling away from the mounts...fitting and removal in seconds !

For use with original Align canopy grommets, Available in Black