Gimbals for Mikrokopter, Droidworx, ArduPilot : ERCmarket radio controlled aircrafts: aerial photography video
2-Axis Tilt-Roll Camera Mount Kit built to accommodate most medium size SLR-like camera. inside is up to 145mm wide
Unassembled 2-Axis Tilt-Roll Camera Mount Kit x 1
Pan-Roll is for RC Heli or Drone Camera Mount Kit , allow 2-Axis control system.
2-Axis Pan-Roll Camera Mount Upgrade Un-assembled Kit
It can also be installed on any aircraft like a Quad-Copter or RC Heli's generally through cable ties.
Brushless Gimbal For Nex / GH camera type, 2-Axis
Included with 2 axis controller, allow this gimbal to work independent regardless the drone its installed on.
can be also mounted on manual handle.
Vibrations isolation dampening pad is included.
3-Axis Aerial Version DSLR Brushless Gimbal for large SLR cameras such Canon D5, D800, fit other SLRs as well
this is a demo model, it was only used for demo purpose, but never used. comes assembled.
Included with Alexmos 3 axis controller, allow this gimbal to work independent regardless the drone or application its installed on.
The Gimbal’s tri-axial rotating parts are made of aluminum , on large flange bearings to reduce the stress on the motor, allowing the motors to rotate smoothly.
Three high-power professional Gimbal motors. The Yaw Axis motor shaft is hollow shaft, allowing wiring through the middle of the motor, reducing twisting during continuous rotation. The motor’s center hole diameter is 12.5 mm, allows 12 wire Slip ring installation.
The Gimbal tube clamps are made of 25mm diameter made from FR-PA thermal injection molded plastic. These clamps have very good elasticity and grip strength while holding carbon tubes, avoiding slips, and scratching the carbon tubes.
Brushless motor direct drive;
When it comes to brushless gimbals whether you are a pro-cinematographer or a multi-rotor hobbyist there is no question AlexMos controllers with Basecam (SimpleBGC) has set the mark in the industry for performance, ease of use and a host of user definable options.\
3 AXIS controller set.
Align G2 gimbal is specially designed for GoPro and Align action camera (Camera not included). G2 gimbal features advanced control system with superior computational power and the high precision brushless motors provide excellent agility and stability as well as powerful functionality. Support the use of satellite receivers and S.BUS/X.BUS receivers and supports programmability through PC interface, or connectivity to iOS/Android smartphones through Bluetooth. Enable you to enjoy aerial photography.
Maximum Control Rotation Rate:
Temperature Range: -20~80°C
3-axis gimbal system for Panasonic GH series or similar sized camera systems. Features strong brushless mtors which makes camera balance less critical. Built in HDMI to AV converter allows live video output into the optional video transmitter.
This gimbal system is a stand-alone design independent of the flight controller.
Align G3-GH gimbal features an advanced control system with superior computational power. The highly integrated design allows for quick conversion between multicopter use and hand held use. Adjustable balance point on all 3 axis for greater camera compatibility, while the high precision brushless motors provide excellent agility and stability. Built in HDMI/AV converter and RC receiver connectivity. Supports programmability through PC interface, or connectivity to iOS/Android smartphones through Bluetooth. Equipped with automatic calibration function during power up. Supports single RC transmitter mode through APS-M, or independent remote control of the gimbal through a dedicated RC transmitter, as well as remote shutter trigger and video start/stop control to capture the optimal footage through precise framing.
Note: camera is not included.
Align PCU Update Connector HEBPCU02.
The gimbal supported 2-Axis brushless motors and is adjustable, so it can be balanced perfectly.
Brushless Gimbal is a midi size, designed for Camcorder, and size of NEX5/7 compact SLR , similar or smaller cameras. It features zero noise, easy adjustment and nearly full range of camera compatibility.
Gimbals 100% produced in Europe, with locally re-winded BL-motors, and with Alex mos type controller.
This gimbal delivered PRE-installed, and as "ready to fly". must be tuned for device
Weight is 250 gr- VERY lightweight gimbal compared to rest of market.
Please note the gimbal can be different from the image, we can optimise the gimbal per customer need, e.g to fit it 100% for camera,or camcorder.
Damping Mount Kit for DJI Phantom 76061004
DJI Focus Wireless Follow Focus System
DJI's Focus is a wireless follow focus that integrates natively with the Zenmuse Z5 series of camera/gimbals systems and can be mounted on rigs equipped with 15mm or 19mm rods - including the Ronin and Ronin-M gimbals. The Focus features a handheld remote controller (transmitter) with a focus knob to give to the feel of a traditional mechanical follow focus. The wireless system sports a range of up to 330' line-of-sight with a delay of only 14ms.
Control accuracy of ±0.002°
DJI Phantom 4 Gimbal Camera 4K
HIGH PERFORMANCE CAMERA
PROFESSIONAL POST PRODUCTION
The Ronin-M 3-Axis Handheld Gimbal Stabilizer from DJI is a camera stabilization system designed to give the operator close to the freedom of unencumbered handheld shooting but without the hand-shake. Suitable for most camera types and configurations up to 8 pounds, the Ronin-M uses brushless motors that work on three axes: one for side-to-side "roll" - keeping the horizon level - one for tilt, and one for pan. The system is computer-controlled and features a tilt range of 105⁰ up / 165⁰ down plus a roll range of ±110⁰. Furthermore, the system boasts a precision of control of ±0.02°, enabling precise camera moves and stability correction against even very fine movements. In addition to handheld shooting, the gimbal can be used in vehicle mounting scenarios and other contexts where vibrations or other abrupt movements would make tripods and rigid camera support systems unsuitable.
The Ronin-M supports dual-operator shooting, much like working with a jib that has a motorized pan/tilt head. In this mode, a second operator would use the included transmitter (radio controller) to manually control camera pan and tilt independently of which way the Ronin-M itself moves. The included transmitter/receiver system operates on 2.4 GHz and is proprietary. If you prefer to use a third-party transmitter there is a D-Bus port on the Ronin-M to install your own receiver.
As with sled and vest style stabilizers, motorized gimbal systems require balancing before use. Once balanced, you can configure the Ronin-M for your particular camera arrangement using the Assistant Software for compatible iOS and Windows (Desktop) devices with Bluetooth. Because every camera and lens combination has a different mass and weight distribution, there is an ATS (Auto Tune Stability) procedure in which each axis will adjust individually, repeating the process until all three are aligned. A gimbal tuning stand is provided so you won't have to hand-hold the rig during this process.
The included 4S lithium-polymer battery powers the Ronin-M for up to six hours. It is a "smart" battery, meaning power regulation and protection circuitry is built-in and there is no separate balancing lead, unlike many lithium-polymer batteries. A charger is also included, and it is important to always use chargers designed for the Ronin-M battery because of the smart circuitry. Two 12V DC PowerTaps and one USB power port on the camera base allow you to power on-camera accessories directly from the Ronin-M battery to simplify your charging regime and avoid unnecessary added weight.
For Cameras Up to 8 lb
Underslung (Suspended) Operation Mode
The software can interface via USB or wirelessly over Bluetooth
DJI Zenmuse Gimbal is a milestone gimbal system which is developed for professional filming, aerial photography for commercial use. Even if aircrafts are in a fast-speed flight, it can still stabilize and control the camera equipment precisely with highest stability. The precision of control angle is within the range of ±0.05°, so picture or video output can reach the best effect.
In order to make the gimbal function the best, DJI provides the customized Gimbal according to the type of camera. For example, the Zenmuse Z15 supports two types of camera, which are Sony Nex5/7 and Panasonic GH2. One type of Gimbal can only support one series of camera. When users want to use a different series of camera, they need purchase the related additional accessories.
Zenmuse gimbal system has three types of control modes, which are Orientation-locked control mode, Non Orientation-locked control mode and Back to Mid-point mode (Horizontal mode). The three types of modes can be switched quickly from one mode to another to meet the different requirements of aerial photography. With the perfect mode and easy operation of the stable 3-axis Zenmuse gimbal, users can take excellent aerial works.
The 3-axis Zenmuse gimbal system has creative design for its mechanical structure design. The slip rings inside avoid the complicated wiring. All the wires of the power and signal lines are integrated into pipes of the Gimbal , which means the axis can rotate without any limitation. The Yaw control could reach ±360°, the Pitch control could reach ±360° and the Roll control could reach ±40° (±360° mechanic continuous rotation).
Due to years of dedication, DJI have achieved for their UAV autopilot systems a perfect attitude-stabilized algorithm, which, together with the high-precise induction device, can perfect performance of attitude control. Without the requirement of extra installation and connection of extra wires, it is also easy to assemble and it can maintain stable when flying.
The separate controller available for the gimbal is connected by the CAN wires with the main controller of DJI autopilot system. According to gimbal attitude feedback, it can control the rotation directions and angles high precisely and also communicate and receive real-time control orders from the main controller of the autopilot system.
In order to minimize the payload of aircraft, the video output module with expanded features like camera shutter is customized to transform HDMI signal to AV with neat wiring, which ensures the smooth and free movement of the 3 axial Gimbal.
The module supports most transmitters and receivers in the market. It provides the Futaba S-Bus receiver with support and it is user-friendly
Zenmuse Gimbal 3-axis rotation controlling function is simple and easy to apply. Stick range corresponds with rotation speed of gimbal axis. Excellent control algorithm guarantees high precision performance of the axis rotation. Zenmuse gimbal rotation speed will not be influenced even when the aircraft is in high-speed spin or quick ascent.
DJI Zenmuse X5 & X5R Vibration Absorbing Board
When using the Zenmuse X5 Series cameras, it is necessary to replace the original vibration absorbing board designed for the Inspire 1’s standard Zenmuse X3 camera.
(The Zenmuse X5 Vibration Absorbing Board is included in the Inspire 1 Pro kit. It is not included with the Zenmuse X5 kit and needs to be purchased separately.)
DJI Zenmuse X5 Camera and gimbal w/out lens
DJI Zenmuse X5 Camera and gimbal with MFT DJI 15mm. lens
DJI Zenmuse X5R RAW DJI Camera and gimbal w/out lens
DJI Zenmuse X5R RAW DJI Camera and gimbal with MFT15MM lens
390* Versatile FPV Pan module + Tilt Module
Camera is not included
Align G3-5D gimbal features an advanced control system with superior computational power. The highly integrated design allows for quick conversion between multicopter use and hand held use. Adjustable balance point on all 3 axis for greater camera compatibility, while the high precision brushless motors provide excellent agility and stability. Built in HDMI/AV converter and RC receiver connectivity. Supports programmability through PC interface, or connectivity to iOS/Android smartphones through Bluetooth. Equipped with automatic calibration function during power up. Supports single RC transmitter mode through APS-M, or independent remote control of the gimbal through a dedicated RC transmitter, as well as remote shutter trigger and video start/stop control to capture the optimal footage through precise framing.
G3-5D Gimbal Specification:
● Weight: Approx. 1250g
Gimbal Controller Specification:
● Input Voltage: DC 12V(3S)
HDMI-AV(Digital to Analog) Converter Specification:
● Input Voltage: DC 12V(3S)
Align G800 gimbal is an upgrade product catered specifically for the needs of aerial photography. The included GS800 gimbal controller features high power computing capability, and various control modes to precisely lock into the shooting object, as well as meet the needs of various other aerial photography needs, allowing optimal imagery to be obtained easily.
This system recommended to be used in conjunction with Align's APS, 3GX and T-Rex 800E. 3k carbon composite material matched with high strength aluminum alloy to form the gimbal backbone, featuring high precision, high stability, capable of high payload, and is able to sustain hard landing of helicopter. When paired with 540 degrees DS815 servo and belt transmission design, the gimbal is capable of wider turning angles with higher precision.
Specification(GS800 CONTROLLER) :
Mini Brushless Gimbal for Gopro 2-3-4 models, 2 axis
This gimbal is designed and produced in EU
Very easy to mount with 2 plates, to be mounted in front as FPV or Photo gimbal.
Controller not included.
Copyright © 2000-2020 eRCMarket. All Rights Reserved.