Video TX & RX

Video TX & RX

All related to FPV, video transmission, Antennas and more

Page of 2
5.8G FPV DIPOLE Mini whip unbreakable 2.8 DBI  TX/RX Racing Antenna

5.8G FPV DIPOLE Mini whip unbreakable 2.8 DBI TX/RX Racing Antenna

5.8G FPV DIPOLE Mini whip unbreakable 2.8 DBI  TX/RX Racing Antenna

This super strong antenna is not easy to break!

Specifications:

  • Connector type: SMA
  • Stopping wave ratio: 1.22-1.51
  • Transmitting efficiency: About 95%
  • Gain: 3.5db
  • Lenght: 73 mm
  • Weight: 6.8g

€10.00

Inc. VAT
Quantity
5.8G Receiver Helical Antenna with protective case SMA

5.8G Receiver Helical Antenna with protective case SMA

5.8G Helical Antenna (Right) for Receiver SMA

Helical Antenna 12dBi, 5.8GHz, Right hand circular polarization, SMA connector.
The circular polarization directional antenna, high gain, ideal for use in the video receiver when intending long ranges. The antennas are right hand circular polarization. Supplied with SMA connector and including a coaxial cable with SMA or PR-SMA (see spc).
 
Specification:
 

  • Frequency: 5.8G
  • Sliver plated line and 24K golden interface
  • Used for receiver, with three-blade antenna on Tx.
  • Suit for video receiver
  • Right Hand Circular Polarization
  • Interface: Please check pictures (please note the connector type you need when place an order) 

Package:
 

  • 5.8G Helical Antenna x 1
  • 15cm coaxial cable x 1

 

€9.90

Inc. VAT
Quantity
5.8GHz Spiro Circular Polarized Antenna Set RP-SMA

5.8GHz Spiro Circular Polarized Antenna Set RP-SMA

Hot of the press, literally, the Circularly Polarized SpiroNet antennas are without doubt the best replacement available for your stock whip antennas. Manufactured to extremely high tolerances and 100% tested on a Rhode & Schwartz analyzer, these antennas yield unparalleled results when compared to hand made variants or DIY antennas.

Left-hand circular polarization or (RHCP) have well and truly been established as the antenna of choice for 5.8GHz FPV use and now you can enjoy the benefits without the head scratching involved in making them yourself. The Antennas include standard SMA connector. The Hard case enclosure will ensure that your antennas are never damaged or bent out of shape while handling or after a ruff landing while the flexible cable ensures easy positioning for optimum performance. 

Specifications:

  • Clover (TX) weight: 7.7g
  • Skew (RX) Weight: 8.6g
  • Connector: SMA 
  • Case size: 33.5m(w) 16mm(h)
  • Cable Length: 73mm(skew) 33.5mm(clover)

 

€18.00

Inc. VAT
Quantity
5.8GHz Spiro Circular Polarized Antenna Set SMA

5.8GHz Spiro Circular Polarized Antenna Set SMA

Hot of the press, literally, the Circularly Polarized SpiroNet antennas are without doubt the best replacement available for your stock whip antennas. Manufactured to extremely high tolerances and 100% tested on a Rhode & Schwartz analyzer, these antennas yield unparalleled results when compared to hand made variants or DIY antennas.

Left-hand circular polarization or (RHCP) have well and truly been established as the antenna of choice for 5.8GHz FPV use and now you can enjoy the benefits without the head scratching involved in making them yourself. The Antennas include standard SMA connector. The Hard case enclosure will ensure that your antennas are never damaged or bent out of shape while handling or after a ruff landing while the flexible cable ensures easy positioning for optimum performance. 

Specifications:

  • Clover (TX) weight: 7.7g
  • Skew (RX) Weight: 8.6g
  • Connector: SMA 
  • Case size: 33.5m(w) 16mm(h)
  • Cable Length: 73mm(skew) 33.5mm(clover)

 

€18.00

Inc. VAT
Quantity
AOMWAY 5.8G RP-SMA Male Tx/VRx FPV Antenna

AOMWAY 5.8G RP-SMA Male Tx/VRx FPV Antenna

AOMWAY 5.8G RP-SMA Male Tx/VRx FPV Antenna

€9.00

Inc. VAT
Quantity
CL-58 5.8GHz Clover-Leaf Spyro Circular Polarized Antenna set

CL-58 5.8GHz Clover-Leaf Spyro Circular Polarized Antenna set

CL-58 5.8GHz Clover-Leaf Spyro Circular Polarized Antenna set, 2 pcs, TX+RX.

Designed for FPV applications.
This offers better looks and excellent protection.
Easy to setup and use standard SMA and RP-SMA connectors.

Description:
SWR≤1.5   
Weight:13g   
Connect: SMA(needle inside) or RP-SMA(hole inside)
Size: TX 8cm,  RX 12cm

€18.00

Inc. VAT
Quantity
Clover Leaf Antenna 5.8GHz TX-RX

Clover Leaf Antenna 5.8GHz TX-RX

Circular Polarization is one of the biggest step forward in the progression of the FPV experience of the last few years. It has improved signal reception on all bands and brought 5.8Ghz video from one of the least practical systems to now one of the best.

This is a 5.8Ghz Cloverleaf antenna for your transmitter and receiver.  A plastic enclosure is included to stop the antenna from being bent or damaged.  The connection on this antenna is a SMA type connector.

A cloverleaf antenna has 3 distinct lobes on it.  Is is usually used to connect to your transmitter unit that is onboard your multicopter or aircraft.  This is an omni-directional antenna so you might have some signal loss when you are flying directly above the receiver as this antenna does not rediate directly below or above the antenna axis.  However overall the cloverleaf antenna is the best type to use for your transmitter.
Cloverleaf Antenna Specifications

Set of TX and RX antennas Included!

  •   Gain: 5dBi
  •   Antenna connector: SMA Plug
  •   Standing wave ratio(SWR): <1.5
  •   Length: 8cm
  •   Weight: 12.5g

€18.00

Inc. VAT
Quantity
DUO Diversity 5.8GHz 48CH (RaceBand) receiver RD945 with auto Scan ,LCD screen

DUO Diversity 5.8GHz 48CH (RaceBand) receiver RD945 with auto Scan ,LCD screen

The Boscam RD945 is  one of the best FPV receivers on the market and now it has been made even better thanks to its recent upgrade, which provided an additional 8 channels to make it RaceBand compatible. Note that it still offers all of the 32 traditional FPV channels, so it's fully compatible with other 5.8Ghz gear on the market including Fatshark & ImmersionRC gear.

In addition to the RD945's wide range of frequencies, it also boasts many other features including, a true 40 channel diversity receiver with dual AV outputs which can be used to feed a monitor or goggles; auto channel search at the push of a button, and a clear LCD display that shows band/channel and the actual frequency number. It also supports a wide input voltage range 6-28v making it compatible with most power sources, including LiPo batteries. Finally, we're also impressed with the construction of the RD945. The Rx is contained within a durable metal case, which also acts to shield the receiver increasing its sensitivity.

Why do I need a diversity reciever?

A diversity receiver is essentially two receivers all in one. In essence, it allows you two mix and match antennas for a solid video link. So it might be that you select a circular polarised omnidirectional antenna, which will provide good reception in all directions in the near field, and a directional high gain patch antenna for long distance flights. The diversity receiver is clever in that it will seamlessly switch between the receiver with the strongest signal.

What is RaceBand?

RaceBand was first pioneered by ImmersionRC to allow more pilots to race together without interferance. Essentially, RaceBand is just another set of 5.8Ghz frequencies, to be specific they are: 5658, 5695, 5732, 5769, 5806, 5843, 5880, 5917. The difference between the RaceBand and the other 5.8Ghz bands is that RaceBand frequencies are more spread out across its band (37mhz separation) thus allowing more pilots to fly FPV together without their video feeds causing interference with each others.

Note that many shops are still selling the the old FR632 32-channel version, which does not support RaceBand.

Features:

  •     48 channels / 6 Bands - includes Race Band channels compatible with Fatshark & ImmersionRC gear
  •     Auto channel scan and lock on
  •     True 5.8GHz 32CH diversity system with indicator
  •     Dual buffered AV output for DVR or second monitor
  •     LCD display, frequency and channel synchronous display
  •     Power off channel memory

RECEIVER Frequency:

    FR1 to FR6 Bands
 

For best range and video link stability we recommend using circular-polarized, Patch or Helical Antenna Set (SMA), see 'related products' below.

€79.90

Inc. VAT
Quantity
Extension Cable for Antenna RP SMA Male to RP Female-20CM

Extension Cable for Antenna RP SMA Male to RP Female-20CM

Extension Cable for Antenna RP SMA Male to RP Female-20CM  - Flexibility Your FPV System Deserves!

An easy way to add the flexibility you need, this flexible adapter cable is an easy and effective way to adapt your FPV system with simplicity & ease.

Utilizing a flexible cable system, this cable allows you to bend your antenna to the most optimal angle, allowing your FPV experience to be maximized with effective range.

Easy to use and a great way to adapt your differing SMA connector types, use this flexible system for a quick and easy solution that gives your FPV system the flexibility it deserves!

Length 20cm

€6.00

Inc. VAT
Quantity
Extension Cable for Antenna RP-SMA jack to RP-SMA plug, 5cm, 90 Degrees

Extension Cable for Antenna RP-SMA jack to RP-SMA plug, 5cm, 90 Degrees

Extension Cable for Antenna RP-SMA jack to RP-SMA plug, 5cm, 90 Degrees - Flexibility Your FPV System Deserves!

An easy way to add the flexibility you need, this flexible adapter cable is an easy and effective way to adapt your FPV system with simplicity & ease.

Utilizing a flexible cable system, this cable allows you to bend your antenna to the most optimal angle, allowing your FPV experience to be maximized with effective range.

Easy to use and a great way to adapt your differing SMA connector types, use this flexible system for a quick and easy solution that gives your FPV system the flexibility it deserves!

Length 5cm

€6.00

Inc. VAT
Quantity
Extension Cable for Antenna SMA jack to SMA plug, 5cm, 90 Degrees

Extension Cable for Antenna SMA jack to SMA plug, 5cm, 90 Degrees

Extension Cable for Antenna SMA jack to SMA plug, 5cm, 90 Degrees - Flexibility Your FPV System Deserves!

An easy way to add the flexibility you need, this flexible adapter cable is an easy and effective way to adapt your FPV system with simplicity & ease.

Utilizing a flexible cable system, this cable allows you to bend your antenna to the most optimal angle, allowing your FPV experience to be maximized with effective range.

Easy to use and a great way to adapt your differing SMA connector types, use this flexible system for a quick and easy solution that gives your FPV system the flexibility it deserves!

Length 5cm

€6.00

Inc. VAT
Quantity
Extension Cable for Antenna SMA jack to SMA plug,10cm, 90 Degrees

Extension Cable for Antenna SMA jack to SMA plug,10cm, 90 Degrees

Extension Cable for Antenna SMA jack to SMA plug, 10cm , 90 Degrees - Flexibility Your FPV System Deserves!

An easy way to add the flexibility you need, this flexible adapter cable is an easy and effective way to adapt your FPV system with simplicity & ease.

Utilizing a flexible cable system, this cable allows you to bend your antenna to the most optimal angle, allowing your FPV experience to be maximized with effective range.

Easy to use and a great way to adapt your differing SMA connector types, use this flexible system for a quick and easy solution that gives your FPV system the flexibility it deserves!

Length 10cm

€6.00

Inc. VAT
Quantity
Extension Cable for Antenna SMA Male to Female-20CM

Extension Cable for Antenna SMA Male to Female-20CM

Antenna extension - Extension Cable for Antenna SMA Male to Female,20CM  - Flexibility Your FPV System Deserves!

An easy way to add the flexibility you need, this flexible adapter cable is an easy and effective way to adapt your FPV system with simplicity & ease.

Utilizing a flexible cable system, this cable allows you to bend your antenna to the most optimal angle, allowing your FPV experience to be maximized with effective range.

Easy to use and a great way to adapt your differing SMA connector types, use this flexible system for a quick and easy solution that gives your FPV system the flexibility it deserves!

Length 20cm

€6.00

Inc. VAT
Quantity
Fpv Complete set, Monitor, TX, Antennas, Camera

Fpv Complete set, Monitor, TX, Antennas, Camera

 This is the set you will need to fly FPV,

Set Included:

  • Diversity receiver monitor 7 or 10" ( choice) with built in Battery, Sunshade, Charger
  • Video-Audio 5.8 GHZ, 25mw receiver CEE approved
  • Set of Spyro Antennas, for TX, RX and Coil Antenna for Diversity receiver
  • 600-700TVL Sony CCD FPV camera

 

€299.00

Inc. VAT
Quantity
Frsky Super 8 High Gain 3dBi Antenna for R9M / R9M Lite Module

Frsky Super 8 High Gain 3dBi Antenna for R9M / R9M Lite Module

The super 8 antenna from Frsky will make your R9M module even better and guaranteed to increase range over the stock duck antenna. Using a specialized antenna design in the figure of 8, this antenna is made to send your RF signals with high efficiency to improve your range and signal quality. TO fit this super 8 antenna, you simply just unscrew the stock one and screw the new one on via the SMA connector.

Specifications

Brand: FrSky

Item Name: FrSky Super 8 Antenna

Frequency Range: 860 – 930MHz ( LBT)

Peak Gain: 3dBi@900Mhz

Feed Impedance: 50 ohm

RF Cable: RG405 Semi-flexible

Connector: SMA internal screw hole

Compatible with modules: R9M / R9M Lite

Kit Contents

1 x FrSky Super 8 Antenna

€15.95

Inc. VAT
Quantity
IPEX Convert Coax wire to SMA/RPSMA ( with adaptor )

IPEX Convert Coax wire to SMA/RPSMA ( with adaptor )

Cable Ipex converter to SMA/RPSMA( optional adaptor )- sometimes can be delivered with SMA connector 90 degrees for easy installation

Features:

  • Name:SMA cable to IPEX
  • Interface Type:external screw internal pin
  • Cable Length:RG1.13 silver plating

Application Fields:

  • WIFI module
  • Network card
  • Desk computer
  • PAD
  • Model airplane remote control
  • Bluetooth
  • Network monitoring
  • Wireless camera
  • Intelligent household
  • Network set-top box
  • Wireless router
  • Optical
  • Interchanger
  • Laptop

€5.90

Inc. VAT
Quantity
MenaceRC Stubby 5.8Ghz Omni LHCP FPV Antenna SMA

MenaceRC Stubby 5.8Ghz Omni LHCP FPV Antenna SMA

Stubby Antenna 5.8Ghz Omni LHCP SMA

The STUBBY RAPTOR antenna NOW even smaller compact Omni less chance of getting it caught on that racing gate or tree.

No compromise in performance, just like its bigger brother, the STUBBY RAPTOR delivers a smooth radiation pattern and a high axial ratio with its unique PCB pagoda construction designed by Maarten Baert.

Features:

  • Small 5.8Ghz Aero design with excellent omni directional pattern
  • Unique PCB construction allows manufacturing within fine tolerances
  • Gain 1.09db with a radiation efficiency of 92%
  • Clearer video reception with upto 20% greater signal received than other omni antenna topology with higher gain
  • High Axial Ratio for reversed polarity rejection, ideal for send and receive as a pair.

Specification:

  • Centre frequency 5.8 GHz
  • Frequency Range: 5550 – 6050 MHz
  • Matching S11 < -20dB, VSWR <1.22
  • Gain: 1.09dB with efficiency: 92%
  • Axial Ratio <1.3
  • Beam width: 360 degrees
  • Left or Right Hand Circular Polarised ( LHCP or RHCP)
  • SMA Connector
  • Strengthened coax to SMA method
  • Sleeved Coax cable
  • Height: 62mm
  • Weight: 9.4grams

 
Credit:

  • Manufactured under License CC BY-SA 4.0 from Maarten Baert
  • www.maartenbaert.be

Package Content:

  • 1x Raptor 5.8Ghz Antenna

€10.90

Inc. VAT
Quantity
RFDESIGN 868MHz telemetry Bundle, 2 modems, Antennas, and connection cable

RFDESIGN 868MHz telemetry Bundle, 2 modems, Antennas, and connection cable

RFD 868+ MHz telemetry Bundle

Long Range telemetry or data-communication Modem-Set the brand RFDesign Pty Ltd.

The Bundle contains all the necessary antennas and cables. Information for commissioning, for example, with the autopilot, the Pixhawk product range can be found here:

ArduPilot Support Radio Modem

Features:

  • Long range> 40km depending on antennas and GCS Setup
  • 1 Watt (30dBm) transmit power (adjustable up to)
  • Low pass filter
  • 20dB low Noise amplifier, high IP3 (updated RFD868+).
  • RX SAW Filter.
  • All I/O ESD protected and filtered
  • The Open Source Firmware SiK (V1.x), field upgradeable, easy to configure.
  • Small, light.
  • Compatible with 3DR/ Hope-RF Radio modules

Additional Features/ Software:

  • Frequency hopping spread spectrum (FHSS)
  • Transparent serial connection
  • Point-to-point or Multipoint network
  • Configuration by simple AT commands for local Radio, RT commands for remote Radio
  • User-configurable serial data rates and air data rates
  • Error correction routines, Mavlink Protocol frames (user-selectable)
  • Mavlink Radio Status Reporting (Local RSSI, Remote RSSI, Local noise, Remote Noise)
  • Automatic antenna Diversity switching on a packet basis in real time
  • Automatic throttling based on radio temperature to avoid Overheating

Technical Data:

  • Frequency Range: 868-869 MHz
  • Output power: 1W (30dBm), controllable in 1dB steps (+/- 1dB @ = 20dBm typical)
  • Air data transfer rates: 4, 8, 16, 19, 24, 32, 48, 64, 96, 128, 192 and 250 kbit/s (user selectable, 64 kStd)
  • +UART-data transfer rates: 9600, 19200, 38400, 57600, 115200, 400k, 921k Baud (user selectable, default 64k)
  • Transmit Power: Max. 1W (30dBm)
  • Receive sensitivity:> 121 dBm at low data rates, high data rates (TBA)
  • Size: 30 mm (wide) x 57 mm (long) x 12.8 mm (thick) - Including RF shield, heatsink and connector-extremities
  • Weight: 14.5 g
  • Mounting: 3 x M2,5 screws, 3 x header pin solder points
  • Power supply: +5 V nominal, (+3.5 V min, +5.5 V max), ~ 800 mA peak at maximum power
  • Temp. Range: -40 to +85 ° C, ready for operation 123 ° C tested from -73 to +

Scope of delivery:

  • 2 x RFD868+ wireless modem
  • 1 x antenna, 868-900MHz quarter wave monopoly 2.1 dBi
  • 1 x antenna, 868-900 MHz Right-angle quarter-monopoly 2.1 dBi
  • 4 x antennas, 868-900 MHz half-wave dipole 3dBi
  • 1 x FTDI USB cable

Software / GCS support:

  • The software solution is an Open Source development called "SiK". It has been re-implemented to the new processor architecture to meet the on the 32-Bit ARM processor core available.
  • A boot loader and an interface to the further development and on-the-spot Upgrade of the Modem Firmware via the serial interface.

Most of the parameters via AT commands configurable, for example, baud rate (air / Uart), frequency band, power levels.
The built-in support for the configuration of the radio equipment RFD900/RFD868 is supported by APM Planner/ Mission Planner.
The default settings are 57600 Baud, N, 8, 1 and 64 k-air data rate.

NOTE:
Please see with your country Telecommunication rules for using this item, the user is the only respocible for using properly the device.

€459.00

Inc. VAT
Quantity
RJX 10CM SMA Pigtail IPEX Connector (2pcs)

RJX 10CM SMA Pigtail IPEX Connector (2pcs)

RJX 10CM SMA Pigtail W/UFL Connector (2pcs)

€6.00

Inc. VAT
Quantity
RP-SMA Plug to SMA Jack adaptor (Hole-hole) straight version

RP-SMA Plug to SMA Jack adaptor (Hole-hole) straight version

RP-SMA Plug to SMA Jack adaptor. basically its Hole to hole adaptor, so if you have Antenna and VTX with pins- this is the adaptor to use

Scope of delivery- 1 adaptor

Please see the DIAGRAM to understand your desired connection

€6.00

Inc. VAT
Quantity
RP-SMA Plug to SMA Jack adaptor (Hole-hole),90 degrees version

RP-SMA Plug to SMA Jack adaptor (Hole-hole),90 degrees version

RP-SMA Plug to SMA Jack adaptor.90 degrees version. basically its Hole to hole adaptor, so if you have Antenna and VTX with pins- this is the adaptor to use

Scope of delivery- 1 adaptor

Please see the DIAGRAM to understand your desired connection

€6.00

Inc. VAT
Quantity
Rush FPV Cherry 5.8GHz SMA 16cm, long variant for Long range FPV

Rush FPV Cherry 5.8GHz SMA 16cm, long variant for Long range FPV

The Rush Cherry antenna is excellent value for money. This is currently the longest variant, a 160 mm. Great for your next long ranger!

Features

  • Extra long for best performance
  • Optimized for FPV racing drones
  • Maximum signal coverage. The bandwidth from 5,6 a 6 GHz covers the entire race band and all channels have an almost uniform transmission strength.
  • Perfect ratio of the circular polarization axis. Effectively eliminates screen flickering caused by multi-path interference.
  • Small and sturdy. Optimized design achieved through massive impact tests. The hose can resist angular bends and shocks to prevent damage to cables.
  • Between 5650 e 5950 MHz, VSWR is less than 1,2, which means that the transmission efficiency is up to 98% This can also help reduce VTX heat.
  • Quick installation. The antenna clips have the same dimensions as the standard flange SMA sockets. The length of the antenna tube can be cut according to your needs.
  • Quality assurance. Cherry antennas are optimized for performance by the Rush FPV Professional Microwave Laboratory and each antenna is qualified by a network analyzer before leaving the factory.

    Specifications
  • I earn: 1,2dBi
  • S11 SWR: 1,4 max – 1,1 me
  • Bandwidth: 5600-6000 MHz
  • axial ratio: circa 1,0
  • Length: 160 mm
  • Polarization: LHCP o RHCP
  • Connector: High School
  • Weight: 11,5 g

    Package Included:
  • 1x antenna SMA  Rush FPV Cherry 5.8GHz

€12.90

Inc. VAT
Quantity
SMA Plug to RP-SMA Jack adaptor (PIN-PIN), 90 degree version

SMA Plug to RP-SMA Jack adaptor (PIN-PIN), 90 degree version

SMA Plug to RP-SMA Jack adaptor, 90 degree version Basically its Pin to Pin adaptor, so if you have antenna and video tx with both side Hole- this is the adaptor you need

Scope of delivery- 1 adaptor

Please see the DIAGRAM below to understand your desired connection

€6.00

Inc. VAT
Quantity
SMA Plug to RP-SMA Jack adaptor(PIN-PIN), straight version

SMA Plug to RP-SMA Jack adaptor(PIN-PIN), straight version

SMA Plug to RP-SMA Jack adaptor. Basically its Pin to Pin adaptor, so if you have antenna and video tx with both side Hole- this is the adaptor you need

Please see the DIAGRAM below to understand your desired connection

€6.00

Inc. VAT
Quantity
TBS Triumph 5.8GHz CP FPV antennas RP-SMA (set of 2pcs)

TBS Triumph 5.8GHz CP FPV antennas RP-SMA (set of 2pcs)

TBS Triumph 5.8GHz CP FPV antennas RP-SMA (set of 2pcs)

Designed by Video Aerial Systems LLC (IBcrazy) and Team-BlackSheep

While other antennas rely on copycat designs the TBS Triumph takes a giant leap in 5.8 GHz antenna technology. Video Aerial Systems LLC (IBcrazy) and Team-BlackSheep have come together to re-invent how the modern 5.8 circular polarized antenna should look and perform.

In our quest for the cleanest video signal and best range possible, we have ventured way beyond the traditional bent lobes of Cloverleaf designs and invested significant time and effort in finding the best antenna designs known to man, and modifying them specifically for FPV use.

After extensive design and testing, we focused on making  sure the Triumph was durable enough to take even the toughest of abuse. After many test flights and extensive feedback from our pilots, we decided to use a double-jacket heavy duty Semi-Rigid cable and tin-plated connectors. For protection we created a special foam-filled and ultrasonic welded enclosure to secure the antenna from inbound trees, or other objects

Features:

  • Manufactured and tested to highest standards
  • Best in class range and signal quality
  • Extra compact and low weight
  • Ultrasonic welded and foam infused cover for ultimate crash-protection
  • Double-jacket semi-rigid cable for heavy impact resistance

Technical Specifications:

  • Frequency range: 5500-6000MHz
  • Gain: 1.26dbic
  • Axial Ratio:   0.74
  • Cable: RG402 (heavy duty)
  • Weight: 11.5g
  • Height: 85mm, 3.3 in
  • Connector: RP-SMA

Package Contents:

  • 2x TBS Triumph antenna RP-SMA

 

€39.90

Inc. VAT
Quantity
TBS Triumph 5.8GHz CP FPV antennas SMA (set of 2pcs)

TBS Triumph 5.8GHz CP FPV antennas SMA (set of 2pcs)

TBS Triumph 5.8GHz CP FPV antennas SMA (set of 2pcs)

The revolution in circular 5.8 GHz technology.
Hand-tuned for ultimate noise and reflection rejection.
True circularity and great range. Designed by none other than IBCrazy.
SMA version.

While other antennas rely on copycat designs the TBS Triumph takes a giant leap in 5.8 GHz antenna technology. Video Aerial Systems LLC (IBcrazy) and Team-BlackSheep have come together to re-invent how the modern 5.8 circular polarized antenna should look and perform.

In our quest for the cleanest video signal and best range possible, we have ventured way beyond the traditional bent lobes of Cloverleaf designs and invested significant time and effort in finding the best antenna designs known to man, and modifying them specifically for FPV use.

After extensive design and testing, we focused on making  sure the Triumph was durable enough to take even the toughest of abuse. After many test flights and extensive feedback from our pilots, we decided to use a double-jacket heavy duty Semi-Rigid cable and tin-plated connectors. For protection we created a special foam-filled and ultrasonic welded enclosure to secure the antenna from inbound trees, or other objects

Features:

  • Manufactured and tested to highest standards
  • Best in class range and signal quality
  • Extra compact and low weight
  • Ultrasonic welded and foam infused cover for ultimate crash-protection
  • Double-jacket semi-rigid cable for heavy impact resistance

Technical specifications:

  • Frequency range: 5500-6000MHz
  • Gain: 1.26dbic
  • Axial Ratio:   0.74
  • Cable: RG402 (heavy duty)
  • Weight: 11.5g
  • Height: 85mm, 3.3 in
  • Connector: SMA

Package contents:

  • 2x TBS Triumph antenna SMA

 

€39.90

Inc. VAT
Quantity
TBS TRIUMPH-STUB 5.8GHz CP FPV antennas RP-SMA (set of 2pcs)

TBS TRIUMPH-STUB 5.8GHz CP FPV antennas RP-SMA (set of 2pcs)

TBS TRIUMPH-STUB 5.8GHz CP FPV antennas RP-SMA (set of 2pcs)

The ultimate FPV racing antenna just got better. With lower weight and even better durability, the TBS Triumph Stub has it all.

While other antennas rely on copycat designs the TBS Triumph takes a giant leap in 5.8 GHz antenna technology. Video Aerial Systems LLC (IBcrazy) and Team-BlackSheep have come together to re-invent how the modern 5.8 circular polarized antenna should look and perform.

In our quest for the cleanest video signal and best range possible, we have ventured way beyond the traditional bent lobes of Cloverleaf designs and invested significant time and effort in finding the best antenna designs known to man, and modifying them specifically for FPV use.

After extensive design and testing, we focused on making  sure the Triumph was durable enough to take even the toughest of abuse. After many test flights and extensive feedback from our pilots, we decided to use a double-jacket heavy duty Semi-Rigid cable and tin-plated connectors. For protection we created a special foam-filled and ultrasonic welded enclosure to secure the antenna from inbound trees, or other objects

Features:

  • Manufactured and tested to highest standards
  • Best in class range and signal quality
  • Extra compact and low weight
  • Ultrasonic welded and foam infused cover for ultimate crash-protection
  • Double-jacket semi-rigid cable for heavy impact resistance

Technical specifications:

  • Frequency range: 5500-6000MHz
  • Gain: 1.26dbic
  • Axial Ratio:   0.74
  • Cable: RG402 (heavy duty)
  • Weight: 8.5g - 9.8g
  • Height: 50mm, 1.97 in
  • Connector: RP-SMA

Package contents:

  • 2x TBS Triumph antenna-Stub RP-SMA (RHCP)

€39.90

Inc. VAT
Quantity
TBS TRIUMPH-STUB 5.8GHz CP FPV antennas SMA (set of 2pcs)

TBS TRIUMPH-STUB 5.8GHz CP FPV antennas SMA (set of 2pcs)

TBS TRIUMPH-STUB 5.8GHz CP FPV antennas SMA (set of 2pcs)

The ultimate FPV racing antenna just got better. With lower weight and even better durability, the TBS Triumph Stub has it all.

While other antennas rely on copycat designs the TBS Triumph takes a giant leap in 5.8 GHz antenna technology. Video Aerial Systems LLC (IBcrazy) and Team-BlackSheep have come together to re-invent how the modern 5.8 circular polarized antenna should look and perform.

In our quest for the cleanest video signal and best range possible, we have ventured way beyond the traditional bent lobes of Cloverleaf designs and invested significant time and effort in finding the best antenna designs known to man, and modifying them specifically for FPV use.

After extensive design and testing, we focused on making  sure the Triumph was durable enough to take even the toughest of abuse. After many test flights and extensive feedback from our pilots, we decided to use a double-jacket heavy duty Semi-Rigid cable and tin-plated connectors. For protection we created a special foam-filled and ultrasonic welded enclosure to secure the antenna from inbound trees, or other objects

Features:

  • Manufactured and tested to highest standards
  • Best in class range and signal quality
  • Extra compact and low weight
  • Ultrasonic welded and foam infused cover for ultimate crash-protection
  • Double-jacket semi-rigid cable for heavy impact resistance

Technical specifications:

  • Frequency range: 5500-6000MHz
  • Gain: 1.26dbic
  • Axial Ratio:   0.74
  • Cable: RG402 (heavy duty)
  • Weight: 8.5g - 9.8g
  • Height: 50mm, 1.97 in
  • Connector: SMA

Package contents:

  • 2x TBS Triumph antenna-Stub SMA (RHCP)

 

€39.90

Inc. VAT
Quantity
Yuneec MK58 UV Power and Cable Kit

Yuneec MK58 UV Power and Cable Kit

Yuneec MK58 UV Power and Cable Kit   

Power and UV Cables to go on the YUNEEC Typhoon G.

Does not include MK58 and antenna.

 

€25.90

Inc. VAT
Quantity
ZRC 5.8GHz 14 dBi High-gain Circular Polarized Panel patch Antenna For FPV System

ZRC 5.8GHz 14 dBi High-gain Circular Polarized Panel patch Antenna For FPV System

5.8Ghz 14dbi Circular Polarized High Gain Flat Panel AntennaLHCP/RHCP For 5.8G FPV Transmitter VS Immersion Fatshark

Designed to be mounted to FPV / goggle systems, this highly compact panel antenna adds excellent directional FPV range that will outperform similar omnidirectional antennas with ease.


Specification:

  • Frequency range: 5.6-6GHz
  • Standing wave ratio: <1: 1.5
  • Polarization: Circular Polarization (LHCP / RHCP)
  • Lobe width: 40 degrees (H + V)
  • F / B:>35db
  • Impedance: 50 ohms
  • Interface: RP-SMA(hole)
  • Size: 73mm x73mm

Features:

  • High gain
  • Anti-interference
  • Suitable for long-range distance

Package included:

  • 1 x antenna

€29.00

Inc. VAT
Quantity
40CH Raceband AVTransmitter With Pigtail Antenna For FPV Multicopter 25mW

40CH Raceband AVTransmitter With Pigtail Antenna For FPV Multicopter 25mW

This is the size and weight savings, while still obtaining good performance.
The FX795T-2 support full range of 40 channels and only weighs 7.5g.
It’s perfect for a wide range of FPV racing aircraft, especially small FPV racing models and FPV racing multicoptors.

€25.00

Inc. VAT
Quantity
Adapter XT60 Male to Male DC 5.5X 2.1mm Power Cable For FPV Goggles Battery

Adapter XT60 Male to Male DC 5.5X 2.1mm Power Cable For FPV Goggles Battery

Amass 200mm XT60 Male Connector to Male DC 5.5X 2.1mm Adapter Power Cable For FPV Goggles Battery

This adapter cable can transfer the RC Drone battery (XT60/ XT30/ T plug) to the goggles battery plug (DC5.5 2.1 plug)

Description:
Brand name: Amass
XT60 to 5.5/5.5mm DC
Length: 200mm
Suitble for FPV system
 
Package Included:
1x Amass XT60 to 5.5/5.5mm DC power cable

€3.00

Inc. VAT
Quantity
Aluminium Heatsink Heat Sink Cooling Cooler Fin 20x14x6mm VTX, ESC

Aluminium Heatsink Heat Sink Cooling Cooler Fin 20x14x6mm VTX, ESC

This is a special Heat Sink to cool down your VTX or ESC.
Reduce the temprature to keep your component safe.

Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)

Dont place it directly over the electronic components since it might shortcut

Material : Aluminum
Sizes 20 x 14 x 6mm
Weight: 2.3 gr
1 pcs included in package

€3.20

Inc. VAT
Quantity
Aluminium Heatsink Heat Sink Cooling Cooler Fin 25x24x16mm  VTX, ESC

Aluminium Heatsink Heat Sink Cooling Cooler Fin 25x24x16mm VTX, ESC

This is a special Heat Sink to cool down your VTX or ESC.
Reduce the temprature to keep your component safe.

Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)

Dont place it directly over the electronic components since it might shortcut

Material : Aluminum
Sizes 24x25mm
Weight: 5.2gr
1 pcs included in package

€3.60

Inc. VAT
Quantity
Aluminum Heatsink For Video transmitter VTX 11x10x6mm

Aluminum Heatsink For Video transmitter VTX 11x10x6mm

This is a special Heat Sink to cool down your VTX.

Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)

Dont place it over the electronic components since it might shortcut

Material : Aluminum
Size 11x10x6mm
Weight: 1gr
1 pcs included in package

€3.00

Inc. VAT
Quantity
Aluminum Heatsink For Video transmitter VTX 14x14x6mm

Aluminum Heatsink For Video transmitter VTX 14x14x6mm

This is a special Heat Sink to cool down your VTX.

Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)

Dont place it over the electronic components since it might shortcut

Material : Aluminum
Size 14x14x6mm
Weight: 1.1gr
1 pcs included in package

€3.00

Inc. VAT
Quantity
Page of 2