T-Rex Nitro

Align T-REX 600 Nitro DFC Combo

Equipped with DFC flybarless head assembly, with extremely low CG design to minimize wind resistance, providing more direct and precise flight control response and higher top speed.
Dual 3K carbon plate side frame design for ease of maintenance and resistance to torque induced flex.
Additional radial bearing is added to the top of the main gear hub to ensure stable rotation, and eliminate jamming of one way bearing.
Newly designed unibody stainless steel tail drive gear center mount, for more precise tail drive gear and higher tolerance.
New high quality carbon rudder control rod assembly using 5mm carbon rod and metal connectors, resulting in improved rudder control precision.
Brand new torque tube front and rear drive gear set, use utilizes newly developed, highest spec and superior anti-wear material to increase the overall strength and durability.
Effectively minimize gear striping and crash damage.
High quality new tail gearbox design, combined with new dual point mounted tail pitch control assembly to minimize slops and increase rudder control precision.
Utilizes high efficient tail drive system.
High speed rated thrust bearing in tail blade grips.
High efficiency tail shaft drive design.
Highly efficient lightened engine cooling fan, reducing engine load and improving cooling efficiency.
Large diameter clutch system with unique installation method for good balance, minimal vibration, and effective power transfer.
Forward mounted rudder servo to protect it from exhaust contamination.
95mm tail blades for sharp rudder response and excellent tail locking ability.
Unique H cross section shaped electronic mounting platform for easy electronic mounting and protection.
Large capacity 440CC fuel tank for up to 10 minutes of extreme 3D flights.
Starting and clutch supporting point utilizes 10mm one way bearing.
All up ready to fly dry weight is only 3200g (7lbs).
Main fuel tank designed with fuel supply stabilization effect.
Impact resistant fiberglass canopy with 3 point hook mounting system for ease of install/removal.
Designed with concepts from large helicopter competitions, for the best static and dynamic flight performance.

Specifications:

• Length: 1160mm
• Height: 357mm
• Main Blade Length: 600mm
• Main Rotor Diameter: 1350mm
• Tail Rotor Diameter: 240mm
• Engine Pinion Gear: 20T
• Main Drive Gear: 170T
• Autorotation Tail Drive Gear: 180T
• Drive Gear Ratio (E:M:T): 8.5:1:4.5
• Fuel Tank Capacity: 440ccm
• Flying Weight Approx: 3200g

Content:

• 1x T-REX 600N DFC Kit
• 2x 600 3G Carbon Fiber Blade
• 2x 95 Carbon Tail Blades
• 3x DS615 Standard servo
• 1x DS655 Specialized servo
• 1x Govemor Sensor
• 1x B6T 2 In 1 Voltage Regulator

Required for assembly:

• 1x Transmitter (7-channel or more, helicopter system)
• 1x Receiver (7-channel or more)
• 1x Standard servo (throttle)
• 1x Engine starter
• 1x Flybarless system
• 1x Digital pitch gauge
• 1x Fuel pump
• 1x Engine fuel
• 1x 50~60 Muffler
• 1x 50~60 Engine
• 1x Receiver battery (2-3S LiPo 7,4V-11,1V 1800-2400mAh)

One of the most classic ALIGN models, the T-REX 600N nitro helicopter. In 2018, we bring you the brand new design of T-REX 600XN, it inherits the design of T-REX 700XN featuring innovation, rigidity and lightness.

Extremely perfection and precision, the T-REX 600XN is about to excite your inner soul to bring back your passion for nitro.

T-REX 600XN adopts the new direct to swashplate servo design, compared to the previous generation T-REX 600N’s push-pull mode control, provides precise and fast control! Utilizing the 550 Flybarless Rotor Head System features an extremely low Center of Gravity (CG) design, to effectively reduces resistance during 3D maneuvers, and increase flight responsiveness and precision.

This designed maintains a 90-degree symmetrical angle between the Rotor Grip Arms and Linkage Rods for superior stable flight performance. The Engineered Narrow Body Design efficiently decrease gear abrasion and frame deformation during flight. The T-REX 600XN maintains the proper CG, by moving the engine forward to allow the fuel tank to be positioned in the center of the main shaft. CG remains consistent as the fuel level changes during flight.

The new steel alloy clutch liner is durable with temperature control designed to avoid the exploding clutch liner or a breaking clutch housing. The steel alloy clutch liner extends the life to over a 1000 flights. The Receiver Mount provides cable and wiring protection, and easy to maintenance by removing a few screws from the mainframe.

The new high voltage output: 6A 7.4V BEC with down / regulation system for constant power to the CCPM server channel for receivers and servos. Includes a built-in one-button push glow plug igniter eliminating the hassle of using traditional electric clip plug on igniters. Also increased external high-frequency filter capacitance to effectively reduce the interference generated by external noise; such as high-speed and high torque servos.

The brand new DS820M/DS825M high voltage brushless servos use brushless motors for fast speed, high torque, superior, and efficient reaction time allows the Align 600XN precise, fast performance. The new CNC machined aluminum case design is aesthetically appealing while acting as a highly efficient heat sink.

The new generation of T-REX 600XN innovative design will excite your inner soul to bring back your passion for nitro!

Features:
After performing many tests to determine the most efficient aerodynamic canopy we are pleased to release this brand new lightweight canopy! This ultimate canopy made of glass and carbon fiber is lightweight and achieves best dynamic performance. Also a new unique paint scheme for the newest member of the T-REX family.

Landing skid is tilted 5 degree forward which improves crashworthiness.
Engineered Narrow Body Design efficiently decrease gear abrasion and frame deformation during flight. The Align T-REX new narrow body design is stronger and increases flight durability.

The new direct to swashplate servo design provides precise and fast control. Designed to maintain a 90-degree symmetrical angle between the Rotor Grip Arms and Linkage Rods for superior and stable flight performance.

Align Advanced Metal Swashplate strongly connects to the rotor holder grips preventing rotor head disengagement during intense flight. Two optional linkage ball mounting holes allow for personal selection of resolution based on desired flight performance.

Receiver mount provides cable and wiring protection, easy to maintain equipment by removing a few screws from the mainframe.
Maintaining the proper Center of Gravity CG is important for helicopters. After extensive Research and Development, moving the engine forward allowed the fuel tank to be positioned in the center of the main shaft. This optimum location for the fuel tank permits the 600XN to maintain consistent CG as the fuel level changes during flight.

The idler pulley gear improves rotation stability and effectively reduces the load from the gears while increasing bearing capacity. The gears made of steel alloy are high strength and wear resistant.

CNC metal reinforcement plate and brace align with frame mounting bolts effectively increasing the torsional strength of the mainframe. Under extreme 3D maneuvers, you can feel the improved reinforcement to the mainframe. Also, the plate helps with engine cooling and adds additional protection for the motor.

Designed specifically for helicopters, utilizing a brushless motor for fast speed, high torque, and superior, efficient reaction time allows the Align 600XN precise, fast performance. The brand new DS820M high voltage brushless servo has a with a new CNC machined aluminum case. The new aluminum case design is aesthetically appealing while acting as a highly efficient heat sink for superior protection of the servo.

High voltage output: 6A 7.4V BEC with down / regulation system for stable power to the CCPM server channel for receivers and servos. Includes a built-in one-button push glow plug igniter eliminating the hassle of using traditional electric clip plug on igniters. Also increased external high-frequency filter capacitance to effectively reduce the interference generated by external noise; such as high-speed and high torque servos.
An integrated motor mounting bracket allows for efficient heat dissipation from the motor. The superior Cooling Motor Mount is CNC from high strength aluminum alloy, and anodized for aesthetically pleasing appearance.

Dual-sided tail servo mount strengthens the entire frame structure while allowing for better accessibility when servicing the 600XN.

Brand new strengthened precision design with high-end M4x8 hexagonal screw upgrade. The new rigid design improves and strengthens the entire structure enhancing tail performance for all pilots.

Specifications:

• Length: 1152mm
• Height: 356mm
• Main Blade Length: 600mm
• Main Rotor Diameter: 1354mm
• Tail Rotor Diameter: 260mm
• Engine Pinion Gear: 20T
• Main Drive Gear: 170T
• Autorotation Tail Drive Gear: 180T
• Drive Gear Ratio (E:M:T): 8.5:1:4.5
• Fuel Tank Capacity: 440ccm
• Flying Weight Approx: 3400g

Content:

• 1x T-REX 600XN Kit
• 2x 600 Carbon Fiber Blade
• 2x 95 Carbon Tail Blades
• 3x DS820M Standard servo
• 1x DS825M Tail servo
• 3x DS530 Throttle servo
• 1x Govemor Sensor
• 1x B6M 2-In-1 Voltage Regulator

Required for assembly:

• 1x Transmitter (7-channel or more, helicopter system)
• 1x Receiver (7-channel or more)
• 1x Engine starter
• 1x Flybarless system
• 1x Governor System (if not integrated in Flybarless System)
• 1x Digital pitch gauge
• 1x Fuel pump
• 1x Engine fuel
• 1x 50~60 Muffler
• 1x 50~60 Engine
• 1x Receiver battery (2-3S LiPo 7,4V-11,1V 1800-2400mAh)

One of the most classic ALIGN models, T-REX 600N nitro helicopter. In 2018, we bring you the brand new design of T-REX 600XN, it inherits the design of T-REX 700XN featuring innovation, rigidity and lightness. Extremely perfection and precision, the T-REX 600XN is about to excite your inner soul to bring back your passion for nitro.

T-REX 600XN adopts the new direct to swashplate servo design, compared to the previous generation T-REX 600N’s push-pull mode control, provides precise and fast control! Utilizing the 550 Flybarless Rotor Head System features an extremely low Center of Gravity (CG) design, to effectively reduces resistance during 3D maneuvers, and increase flight responsiveness and precision.

This designed maintains a 90-degree symmetrical angle between the Rotor Grip Arms and Linkage Rods for superior stable flight performance. The Engineered Narrow Body Design efficiently decrease gear abrasion and frame deformation during flight. The T-REX 600XN maintains the proper CG, by moving the engine forward to allow the fuel tank to be positioned in the center of the main shaft. CG remains consistent as the fuel level changes during flight.

The new steel alloy clutch liner is durable with temperature control designed to avoid the exploding clutch liner or a breaking clutch housing. The steel alloy clutch liner extends the life to over a 1000 flights. The Receiver Mount provides cable and wiring protection, and easy to maintenance by removing a few screws from the mainframe.

The new high voltage output: 6A 7.4V BEC with down / regulation system for constant power to the CCPM server channel for receivers and servos. Includes a built-in one-button push glow plug igniter eliminating the hassle of using traditional electric clip plug on igniters. Also increased external high-frequency filter capacitance to effectively reduce the interference generated by external noise; such as high-speed and high torque servos. The brand new DS820M/DS825M high voltage brushless servos use brushless motors for fast speed, high torque, superior, and efficient reaction time allows the Align 600XN precise, fast performance. The new CNC machined aluminum case design is aesthetically appealing while acting as a highly efficient heat sink.

The new generation of T-REX 600XN innovative design will excite your inner soul to bring back your passion for nitro!

Features:

After performing many tests to determine the most efficient aerodynamic canopy we are pleased to release this brand new lightweight canopy! This ultimate canopy made of glass and carbon fiber is lightweight and achieves best dynamic performance. Also a new unique paint scheme for the newest member of the T-REX family.

Landing skid is tilted 5 degree forward which improves crashworthiness.

Engineered Narrow Body Design efficiently decrease gear abrasion and frame deformation during flight. The Align T-REX new narrow body design is stronger and increases flight durability.

The new direct to swashplate servo design provides precise and fast control. Designed to maintain a 90-degree symmetrical angle between the Rotor Grip Arms and Linkage Rods for superior and stable flight performance.

Align Advanced Metal Swashplate strongly connects to the rotor holder grips preventing rotor head disengagement during intense flight. Two optional linkage ball mounting holes allow for personal selection of resolution based on desired flight performance.

Receiver mount provides cable and wiring protection, easy to maintain equipment by removing a few screws from the mainframe.
Maintaining the proper Center of Gravity CG is important for helicopters. After extensive Research and Development, moving the engine forward allowed the fuel tank to be positioned in the center of the main shaft. This optimum location for the fuel tank permits the 600XN to maintain consistent CG as the fuel level changes during flight.

The idler pulley gear improves rotation stability and effectively reduces the load from the gears while increasing bearing capacity. The gears made of steel alloy are high strength and wear resistant.

CNC metal reinforcement plate and brace align with frame mounting bolts effectively increasing the torsional strength of the mainframe. Under extreme 3D maneuvers, you can feel the improved reinforcement to the mainframe. Also, the plate helps with engine cooling and adds additional protection for the motor.

Designed specifically for helicopters, utilizing a brushless motor for fast speed, high torque, and superior, efficient reaction time allows the Align 600XN precise, fast performance. The brand new DS820M high voltage brushless servo has a with a new CNC machined aluminum case. The new aluminum case design is aesthetically appealing while acting as a highly efficient heat sink for superior protection of the servo.

High voltage output: 6A 7.4V BEC with down / regulation system for stable power to the CCPM server channel for receivers and servos. Includes a built-in one-button push glow plug igniter eliminating the hassle of using traditional electric clip plug on igniters. Also increased external high-frequency filter capacitance to effectively reduce the interference generated by external noise; such as high-speed and high torque servos.
An integrated motor mounting bracket allows for efficient heat dissipation from the motor. The superior Cooling Motor Mount is CNC from high strength aluminum alloy, and anodized for aesthetically pleasing appearance.

Dual-sided tail servo mount strengthens the entire frame structure while allowing for better accessibility when servicing the 600XN.
Brand new strengthened precision design with high-end M4x8 hexagonal screw upgrade. The new rigid design improves and strengthens the entire structure enhancing tail performance for all pilots.

Specifications:

• Length: 1152mm
• Height: 356mm
• Main Blade Length: 600mm
• Main Rotor Diameter: 1354mm
• Tail Rotor Diameter: 260mm
• Engine Pinion Gear: 20T
• Main Drive Gear: 170T
• Autorotation Tail Drive Gear: 180T
• Drive Gear Ratio (E:M:T): 8.5:1:4.5
• Fuel Tank Capacity: 440ccm
• Flying Weight Approx: 3400g

Content:

• 1x T-REX 600XN Kit
• 1x Align 55H Engine (O.S. 55HZ Hyper)
• 1x Align High Performance Muffler
• 2x 600 Carbon Fiber Blade
• 2x 95 Carbon Tail Blades
• 3x DS820M Standard servo
• 1x DS825M Tail servo
• 3x DS530 Throttle servo
• 1x Govemor Sensor
• 1x B6M 2-In-1 Voltage Regulator

Required for assembly:

• 1x Transmitter (7-channel or more, helicopter system)
• 1x Receiver (7-channel or more)
• 1x Engine starter
• 1x Flybarless system
• 1x Governor System (if not integrated in Flybarless System)
• 1x Digital pitch gauge
• 1x Fuel pump
• 1x Engine fuel
• 1x Receiver battery (2-3S LiPo 7,4V-11,1V 1800-2400mAh)

Features:

• Equipped with DFC flybarless head assembly, with extremely low CG design to minimize wind resistance, providing more direct and precise flight control response and higher top speed.
• Dual 3K carbon plate side frame design for ease of maintenance and resistance to torque induced flex.
• Additional radial bearing is added to the top of the main gear hub to ensure stable rotation, and eliminate jamming of one way bearing.
• Newly designed unibody stainless steel tail drive gear center mount, for more precise tail drive gear and higher tolerance.
• New high quality carbon rudder control rod assembly using 5mm carbon rod and metal connectors, resulting in improved rudder control precision.
• Brand new torque tube front and rear drive gear set, use utilizes newly developed, highest spec and superior anti-wear material to increase the overall strength and durability. Effectively minimize gear striping and crash damage.
• High quality new tail gearbox design, combined with new dual point mounted tail pitch control assembly to minimize slops and increase rudder control precision.
• Utilizes high efficient tail drive system.
• High speed rated thrust bearing in tail blade grips.
• High efficiency tail shaft drive design.
• Highly efficient lightened engine cooling fan, reducing engine load and improving cooling efficiency.
• Large diameter clutch system with unique installation method for good balance, minimal vibration, and effective power transfer.
• Forward mounted rudder servo to protect it from exhaust contamination.
• 95mm tail blades for sharp rudder response and excellent tail locking ability.
• Unique H cross section shaped electronic mounting platform for easy electronic mounting and protection.
• Large capacity 440CC fuel tank for up to 10 minutes of extreme 3D flights.
• Starting and clutch supporting point utilizes 10mm one way bearing.
• All up ready to fly dry weight is only 3200g (7lbs).
• Main fuel tank designed with fuel supply stabilization effect.
• Impact resistant fiberglass canopy with 3 point hook mounting system for ease of install/removal.
• Designed with concepts from large helicopter competitions, for the best static and dynamic flight performance.

Specifications:

• Length: 1160mm
• Height: 357mm
• Main Blade Length: 600mm
• Main Rotor Diameter: 1350mm
• Tail Rotor Diameter: 240mm
• Engine Pinion Gear: 20T
• Main Drive Gear: 170T
• Autorotation Tail Drive Gear: 180T
• Drive Gear Ratio (E:M:T): 8.5:1:4.5
• Fuel Tank Capacity: 440ccm
• Flying Weight Approx: 3200g

Includes:

• 1x T-REX 600N DFC Kit
• 1x MICROBEAST Plus Flybarless System
• 2x 600 3G Carbon Fiber Blade
• 2x 95 Carbon Tail Blades
• 3x DS615 Standard servo
• 1x DS655 Specialized servo
• 1x Govemor Sensor
• 1x B6T 2 In 1 Voltage Regulator

Required for assembly:

• 1x Transmitter (7-channel or more, helicopter system)
• 1x Receiver (7-channel or more)
• 1x Standard servo (throttle)
• 1x Engine starter
• 1x Digital pitch gauge
• 1x Fuel pump
• 1x Engine fuel
• 1x 50~60 Muffler
• 1x 50~60 Engine
• 1x Receiver battery (2-3S LiPo 7,4V-11,1V 1800-2400mAh)

The 2008 Align T-Rex 700N was developed based on years of R&D experiences, with superior design and economical pricing that brought 700 class glow helis to the masses, enabling Align to achieve a brand new milestone.
Now to celebrate this achievement, Align improved upon the already excellent design and introduces the brand new T-Rex 700N DFC!

Similar to the rigid and light design of the original, the most recognizable feature of the T-Rex 700N DFC is its narrow profile, which creates the impression of solid and simplicity visual effect.
The DFC main rotor system provides more direct and faster control feedback.
The new M1 helical main gear and new style tail control assembly improves the main gear durability and tail locking performance.
Utilizes larger capacity fuel tank for larger displacement engines, increasing 3D flight duration.

Features:

• Equipped with the low CG DFC rotor head, exhibits exhilarating 3D performance and unimaginable flight speed.
• 700DFC CCPM Metal Swashplate and metal main shaft bearing block.
• New style H-cross section electronics mounting platform for simplified installation of electronics.
• Precision CNC machined aluminum pieces including elevator servo mount.
• Equipped with new high strength cnc m1 helical main gear and tail drive bevel gear assembly, featuring reinforced overall gear structure and increased gear thickness, effectively improves gear′s anti torsion ability to prevent gear from deforming under extreme power,reducing gear wear and power loss.
• 3K carbon plate narrow frame design, simple yet highly rigid, making assembly and maintenance convenient.
• Utilizes larger capacity fuel tank for larger displacement engines, increasing 3D flight duration.
• Tailboom is extended by 15mm to support the use of 720mm main blades. When equipped with 105 or 120 class engine, there will be a noticeable increase in power and performance!
• High quality new tail gearbox design, combined with new dual point mounted tail pitch control assembly to minimize slops and increase rudder control precision.

Specifications:

Length: 1361mm
Height: 385mm
Main Blade Length: 700mm
Main Rotor Diameter: 1582mm
Tail Blade Length: 115mm
Tail Rotor Diameter: 281mm
Engine Pinion Gear: 14T
Main Drive Gear: 112T
Autorotation Tail Drive Gear: 104T
Tail Drive Gear: 21T
Drive Gear Ratio: 8:1:4.95 (E:M:T)
Fuel Tank Capacity: 660cc
Weight (with Power System): approx. 4200g

Includes:

• 1x T-REX 700 Nitro Kit
• 2x 700mm Carbon fiber Main blade
• 2x 115mm Carbon fiber Tail blade
• 1x 2 In 1 Voltage regulator combo
• 3x DS615 Digital servo
• 1x DS655 Digital servo
• 1x Aluminum Tail Boom

Required for assembly:

• 1x Transmitter (7-channel or more, helicopter system)
• 1x Receiver (7-channel or more)
• 1x Standard servo (for throttle)
• 1x Flybarless System
• 1x Governor Sensor
• 1x Engine starter
• 1x Digital pitch gauge
• 1x Fuel pump
• 1x Engine fuel
• 1x 90-120 Muffler
• 1x 90-120 Engine

T-REX 700XN Dominator KIT only NEW 2018 model

Features:

• New slim chassis design
• Revised clutch lining with steel alloy
• New powerful cooling system
• Reinforced carbon rear support

Technical specifications:

• Length: 1346mm
• Height: 384mm
• Width: 202mm
• Main rotor blade length: 700mm
• Main rotor diameter: 1570mm
• Tail rotor blade length: 106mm
• Tail rotor diameter: 281mm
• Motor pinion: 13Z
• Main gear: 107Z
• Autorotation gear: 104Z
• Tail rotor gearbox: 22Z
• Translation: 8.23: 1: 4.73
• Tank capacity: 630cc
• Take-off weight (with battery): 4540g

Content:

• 1x Align T-REX 700XN Dominator kit ONLY( all below not included)
• 1 pair of 700mm carbon main rotor blades
• 1 pair of 106mm carbon tail rotor blades
• 3x Align DS820M swashplate servo
• 1x Align DS825M tail servo
• 1x Align DS530 throttle servo
• 1x Align B6TX 2-in-1 voltage regulator / pre-glow unit
• 1x BEASTX Governor Sensor

T-REX 700XN Dominator Super Combo

Features:

• New slim chassis design
• Revised clutch lining with steel alloy
• New powerful cooling system
• Reinforced carbon rear support
• New main and tail rotor blade design in yellow / black
• Includes the proven DS820M / DS825M High Voltage Brushless Servos plus DS530 Digital Gas Servo

Technical specifications:

• Length: 1346mm
• Height: 384mm
• Width: 202mm
• Main rotor blade length: 700mm
• Main rotor diameter: 1570mm
• Tail rotor blade length: 106mm
• Tail rotor diameter: 281mm
• Motor pinion: 13Z
• Main gear: 107Z
• Autorotation gear: 104Z
• Tail rotor gearbox: 22Z
• Translation: 8.23: 1: 4.73
• Tank capacity: 630cc
• Take-off weight (with battery): 4540g

Content:

• 1x Align T-REX 700XN Dominator
• 1 pair of 700mm carbon main rotor blades
• 1 pair of 106mm carbon tail rotor blades
• 3x Align DS820M swashplate servo
• 1x Align DS825M tail servo
• 1x Align DS530 throttle servo
• 1x Align B6TX 2-in-1 voltage regulator / pre-glow unit
• 1x BEASTX Governor Sensor
• 1 x MICROBEAST Plus Flybarless System

 

See Product Options if you would like to remove servos or MICROBEAST Plus Flybarless System.

Align T-Rex 700XN Super Combo with Engine, Muffler & FREE Fuel 4x5 Litres!

Content:

• T-REX 700XN Dominator Super Combo NEW 2018 model - RH70N11X
• 1 x FREE box of 4x5 Litres Optifuel OPTIMIX-20 or 25SLV Ready fuel

included

Engine:

• OS 105 HZ

Muffler:

Stock dependent( power boost, mrce, etc)