Multi-Rotor Frames

Align M470L Multicopter Quadcopter Super Combo Without gimbal

Align M470L Multicopter Quadcopter Super Combo Without gimbal

Align M470L Multicopter Quadcopter Super Combo

After times of researches and development, Align R&D team dedicated all of its technical expertise and experiences into the development of a brand new aerial photography platform, to give birth to the brand new.

Moisture resistant shape at the pinnacle of power and beauty, industrial and structural design. Encompass stability control system, features light weight, strong payload, and long flight time.
Superior in both high speed agility and static stability, this multi-purposed professional multicopter exceeds in all areas such as aerial photography or as leisurely sports flyer; yet its light weight allows for easy transport anywhere.

Align G2 gimbal is specially designed for GoPro. G2 gimbal features advanced control system with superior computational power and the high precision brushless motors provide excellent agility and stability as well as powerful functionality.
Support the use of satellite receivers and S.BUS/X.BUS receivers and supports programmability through PC interface, or connectivity to iOS/Android smartphones through Bluetooth. Enable you to enjoy aerial photography.

Specification

  • Airframe Diameter: 710mm
  • Height: 266mm
  • Main Blade Length: 179mm
  • Main Rotor Diameter: 391mm
  • Flying Weight(without battery): 2500g

Standard Equipment

  • Multicopter Canopy x 1
  • 7 Inch Main Rotor x 4 Sets
  • External Status LED x 1
  • BL4213(370KV) Brushless Motor x 4
  • Multicopter Brushless ESC x 4
  • PCU Power Control Unit x 1
  • APS-M Multicopter Controller x 1
  • Multicopter GPS Sensor x 1

APS-M Flight Control System Specification

  • Input Voltage:DC 4.5~8.4V
  • Operating Current Consumption:<250mA @ 4.8V
  • Operating Frequency:400Hz
  • Operating Temperature:-20℃~65℃
  • Hovering Precision (Depending on Satellite Status):Horizontal ±1m Vertical ±1m
  • Maximum Flight Speed:Horizontal 15m/sec Vertical 6m/sec
  • Maximum Altitude Restriction:700m(2297ft) above the takeoff point
  • Maximum Angular Speed:
  • Aileron 115°/sec
  • Elevator 115°/sec
  • Rudder 145°/sec
  • Maximum Tilting Angle:30 degrees
  • Supports External Peripherals:"G2/ G3 Gimbal、OSD+FPV Video Transmitter "
  • Supports Multicopter Configurations:"4 rotors +, 4 rotors X, 6 rotors +, 6 rotors X, 8 rotors +, 8 rotors X."
  • Dimension:49x34.3x20mm

PCU Power Control Unit

  • Input Voltage:13.2V~25.2V(4S~6S Li-Po)
  • Operating Frequency:500KHz
  • Dimension:62x35x26mm

BL4213 Motor 370KV(RPM/V)

  • Input Voltage:DC 22.2V
  • Max Continuous Current:25A
  • Max Continuous Power:550W
  • Stator Arms:12
  • Magnet Poles:14
  • Dimension/Weight:4x52x33mm / 185g

Motor ESC

  • Input Voltage:13.2V~25.2V(4S~6S Li-Po)
  • Max Continuous Current:40A
  • Dimension:74.2x27x12.7mm

€699.00

Inc. VAT
Quantity
Bomber HEXA 1.1

Bomber HEXA 1.1

This HEXAcopter frame is the part of our new super professional range,which was developed over 2 years of research.

It`s made from extra strong patented technology carbon fiber plates and tubes, using our own technologies and equipment. It`s build to provide very smooth and stable flight with extra-heavy up 5kg payloads .

This frame is foldable - it`s very comfortable for transport . You`ll be need to release 12pcs of wingnuts to fold the motor arms and landing gears to put your copter into the storage place.

Two big li-po shelves allow the use of two-four LiPos to increase flying time and make their replacement easy and in correct CG.

The protection cage will keep the copter`s electronic equipment in cases of over flips, protecting expensive electronics.

Ultimate camera mount adaptor plate is specially designed to reduce vibration on camera . It`s compatible with all camera mounts .

The Frame made to mount Allstandard controllers as the ones necessary for the distribution board with the speed controllers.

This machine including a large foldable landing gear (350-500 mm of clearance).

The frame is delivered partially assembled, so building is faster and easier.

Diameter of the frame +- 1100mm.

Weight of the frame with landing gears, protection cage and camera mount adaptor plate – 1950 gr

€790.00

Inc. VAT
Quantity
Bomber QUAD 1.1

Bomber QUAD 1.1

This co-axial quad/octocopter frame is the part of our new super professional range,which was developed over 2 years of research.

  • It`s made from extra strong patented technology carbon fiber plates and tubes, using our own technologies and equipment.
    It`s build to provide very smooth and stable flight with extra-heavy up 5kg payloads .
  • This frame is foldable - it`s very comfortable for transport . You`ll be need to release 12pcs of wing nuts to fold the motor arms and landing gears to put your copter into the storage place.
  • Two big li-po shelves allow the use of two-four LiPos to increase flying time and make their replacement easy and in correct CG.
  • The protection cage will keep the copter`s electronic equipment in cases of overflips, protecting expensive electronics.
  • Ultimate camera mount adaptor plate is specialy designed to reduce vibration on camera . It`s compatible with all camera mounts .
  • The holes to mount standard controllers and also the MikroKopter electronics are already foreseen on the centerplate, as the ones necessary for the distribution board with the speed controllers.
  • This machine including a large foldable landing gear (350mm of clearance).
  • The frame is delivered partially assembled, so building is faster and easier.
  • Diameter of the frame +- 1100mm.
Weight of the frame with landing gears, protection cage and camera mount adaptor plate – 2011gr

€899.00

Inc. VAT
Quantity
H6-12 HEXACOPTER

H6-12 HEXACOPTER

This is a hexacopter  main frame, landing gear . Total expected weight to fly inclusive IOSD/VIDEO 4kg

This product can be supplied as Frame only, with landing gear, and with camera mount. all per customer choice.

Main Highlights!

  • 100% Material and product is made In Europe, with highest Grade Carbon fiber for Maximum strength and performance.
  • The 650 frame can be equipped in single or Coaxial config.
  • Max pick up weight is up to 2.9 kg ( nett Pickup weight, excluding the own weight of the frame/electronics)
  • Fold-able Arms, for easy transportation and carriage. can fit all in Supermarket Bag

Technical Data

  • main frame`s weight ~420gr,
  • size between motor axes ~650mm
  • equipped with single-battery slider system (it`s possible to fit till to 4s 6000mAh lipo)


Sliding battery tray, for easy battery replacement.

Landing gear, Height is 205mm, width between skids = 400mm. Weight ~110gr.
All other electronic parts/ Motors and camera are not included in the set

€379.00

Inc. VAT
Quantity
H6-12 HEXACOPTER EXTENDED

H6-12 HEXACOPTER EXTENDED

This is an Extended hexacopter combo set - main frame, landing gear and camera mount. Size is +- 900mm. Frame complete weight ~960gr.

This product can be supplied as Frame only, with landing gear, and with camera mount. all per customer choice.

Main Highlights!

=Produced In Europe, with highest Grade Carbon fiber for Maximum strength and performace.

=The 900 frame can be equipped in each arm with 1 or 2 motors, e.g 6 motors and if added also pusher motors, it can be 12.

=Max pick up weight is up to 5.5 kg ( nett Pickup weight, excluding the own weight of the frame/electronics)

=Foldable Arms, Landing gear, camera mount, for easy transportation and carriage. can fit all in Supermarket Bag

Technical Data

- main frame`s weight ~620 gr,
- size between motor axes ~900mm
- equipped with Dual-battery slider system ( Recommended 2 x 3s 5000 lipo), two battery mount plates are included.

-- camera mount is is producing in two options :1- compatible with pocket-size cameras - like Canon Ixus ,SONY and others pocket size. and second - for GoPro.

Any of mounts are equipped with two servos TGY930. Every Axe supported by Dual ball bearings
Working angles : ailerons +-30 degrees, elevator -90 /+10degrees.
Camera mount`s weight ~230gr.

- Sliding battery trays, for easy battery replacement.

-Landing gear, Height is 205mm, width between skids = 400mm. Weight ~110gr.

All other electronic parts/ Motors and camera are not included in the set

€529.00

Inc. VAT
Quantity
Octocopter 1100mm size Frame

Octocopter 1100mm size Frame

This classic octocopter frame  is the part of our new professional products line , which was designed and tested . It`s made from extra strong carbon fiber plates and tubes,using patented technologies and equipment.
It`s build to provide very smooth and stable flight with up 4.5kg payloads .
This frame is foldable- comfortable for transportation . You`ll be need to release 20pcs of wing nuts to fold the motor arms and landing gears to put your machine into the storage place.
Two li-po shelves  allow the use of two LiPos to increase flying time and easy replacement within seconds..
The protection cage will keep the copter`s electronic equipment in cases of over flips or problematic situations.
Camera mount adapter plate is  specialy designed to reduce vibrations on camera . It`s compatible with most today camera mounts
The holes to mount the MikroKopter electronics are already foreseen on the center-plate, as the ones necessary for the distribution board  with the speed controllers.  
This kit includes a large foldable landing gear (300mm of clearance).
This frame  is delivered partially assembled, so building is faster and easier.

Diameter of the frame-1100mm
Weight of the frame with landing gears, protection cage and camera mount adaptor plate – 1470gr.

 

€869.00

Inc. VAT
Quantity
Sky hero Little Spyder 450mm Aluminium carry case

Sky hero Little Spyder 450mm Aluminium carry case

Carry case, with foam for Sky hero little spyder, however perfectly fits other 450 size machines and also FPV racers

€79.00

Inc. VAT
Quantity
Sky-Hero Spy Mutirotor Y6 Super Combo

Sky-Hero Spy Mutirotor Y6 Super Combo

New Innovative design Multi-copter- Spy, Produced in Belgium. this machine is 600 or 750 or 900mm wide(choice) This product is a Y6 Combo,means you have 6 motors on the machine.This setup is made for 4S lipo, 6S setups also possible as option Combo delivered with the following: Sky hero Spy kit
  • 6 x Avizar MC3536, KV adapted to the version(4/6S)
  • 6 x ESC 40A programmed, Special size to enter the SKY HERO tube arms
  • 6 x Fully balanced props . size of prop will be delivered based on machine size.
  • 1 x Power distribution Board or Distribution wire..
  • 1 x Canopy
To complete the combo you will need your radio, Flight controller, and Lipo battery. * If 6s setup chosen, 380 kv will be delivered, together with larger propellers - to suit 6S setups. Building a Drone is not a straight forward. Proper installation is a  hassle, especially cheap motors and electronics are very simplified, and require a lot of "Know how". Non experienced people can take up to hundred hours to build one model and still suffer from bad Vibrations, programming complexes, Tuning, and much more. We are offering "One stop" service for all your needs. Please ask us for this option cost.

€899.00

Inc. VAT
Quantity
Sky-Hero Spyder Mutirotor X4 Super Combo, Motors, ESC's,Props

Sky-Hero Spyder Mutirotor X4 Super Combo, Motors, ESC's,Props

New Innovative design Multicopter- Spyder, Produced in Belgium. this machine is 700 or 850 or 1000mm wide(choice)

This product is a X4 Combo,means you have 4 motors on the machine.This setup is made for 4S lipos, 6S setups also possible as option

Combo delivered with the following:

           Sky hero Spyder Frame ( choose size)

  • 4 x Avizar MC3536-710 or 380kv, or T-motor  motors
  • 4 x ESC SimonK programmed, Special size to enter Sky hero tube arms
  • 4 x Fully balanced props ,size of prop will be delivered based on machine size.
  • 1 x Power distribution Board 80amp
  • 1 x Canopy- several options possible, comment what is your preference( stock dependant)

 

* If 6s setup chosen, 380 kv will be delivered, together with larger propellers - to suit 6S setups.

 

Movie showing MC3536 motors and 40A esc in use

€899.00

Inc. VAT
Sky-Hero Spyder Mutirotor X8 Super Combo, Motors, ESC's,Props

Sky-Hero Spyder Mutirotor X8 Super Combo, Motors, ESC's,Props

New Innovative design Multicopter- Spyder, Produced in Belgium. this machine is 700 or 850 or 1000mm wide(choice)

This product is a X8 Combo,means you have 8 motors on the machine.This setup is made for 4S lipos, 6S setups also possible as option.

Combo delivered with the following:

           Sky hero Spyder Frame kit

  • 8 x Avizar MC3536-710KV(4s) or 380KV (6s)or T-motor motors
  • 8 x ESC 40-60A SimonK 2-6S lipo, programmed, Optimized and size will enter the arms of Spyder.
  • 8 x Fully balanced props 11-14" ( choice of Graupner E, APC, Wood ) size of prop will be delivered based on machine size.
  • 1 x Power distribution Board 80amp
  • Canopy of choice( Stock dependent)

To complete the combo you will need your radio, Flight controller, and Lipo battery.

* If 6s setup chosen, 380 kv will be delivered, together with larger propellers - to suit 6S setups.

Movie showing MC3536 motors and 40A esc

- Build your Multi rotor in a NASA way, by experts.

Building a Drone is not a straight forward. Proper installation is a  hassle, especially cheap motors and electronics are very simplified, and require a lot of "Know how".

Non experienced people can take up to hundred hours to build one model and still suffer from bad Vibrations, programming complexes, Tuning, and much more.

We are offering "One stop" service for all your needs.

Please ask us for extra charges

€1328.00

Inc. VAT
XuGong v2/Pro – Foldable FPV Quadcopter Kit

XuGong v2/Pro – Foldable FPV Quadcopter Kit

XuGong v2/Pro – Foldable FPV Quadcopter

The most portable FPV quadcopter on the market today. A full-featured quadcopter constructed from beautiful carbon fiber, and CNC-milled aluminium.


The FPV’ers Quadcopter
The XuGong v2/Pro was designed by FPVers, for FPVers.
Designed for fully immersive flight, delivering high-quality, stabilized video footage, from a tailor-made aerial platform.

Desrciption:

  • Compact Foldable Design
  • Lightweight frame leads to > 20 minute flight times
  • Built-in EzOSD, with multicopter enhancements
  • Single-cable link to the EzUHF, with full up-link status
  • Carbon fiber frame, CNC milled aluminium arms
  • Integrated telemetry down-link
  • USB port for future upgrades

Telemetry Down-link:
The XuGong v2/Pro transmits all on-board telemetry to the ground, using the A/V down-link.
Battery status, Uplink status (RSSI, Link quality, etc.), GPS position, are all available in the telemetry stream.
The ImmersionRC Antenna Trackers can use this data to point a high-gain antenna directly at the model.
The iTelemetry dongle provides an interface between this telemetry feed, and a smartphone/tablet, with applications available for the iOS and Android devices.


Very Compact:
There are not many product on the market that fold into such a small space, with just a few seconds required to unfold and fly.
Props remain attached, no tools required, ‘Press, Unfold, and FLY!’

Specifications:

  • Max. Prop Size: 10 Inch
  • OSD: EzOSD-based, with Multicopter additions
  • Flight Controller: DJI Naza Lite, -M, v2 recommended, others supported
  • GPS: Naza GPS pickoff (Position + static Magnetometer)
  • Camera Switch: Manual, between Flight Cam, and GoPro, with auto-failover
  • Camera Power: 1.5A for GoPro, FlightCam powered from Video Tx
  • Flight Cam: Bracket to mount FatShark CMOS 600TVL + others (optional accessory)
  • Weight: AUW, RTF, ~1.5kg (typical)
  • Folded Size: 24cm W x 30cm L x 14cm H
  • Suitable Battery: 5200mAh 4s 10C recommended (for 20 minute flight times)
  • Suitable Motors: 2212/920kV, DJI E300, or Tiger AirGear 350
  • Flight Time: Typ. 20 min

Included in the kit:

  • CNC-milled aluminium & carbon fiber frame
  • Wirering
  • PCB

 

€249.90

Inc. VAT
Quantity