Futaba

Page of 3
12FG charge connector

12FG charge connector

Connector DIY for charge cable. You will need to solder the cable , supplied connector Only

€5.00


€4.13 Ex VAT
Quantity
Futaba 12FG 2.4GHz FASST Radio TRANSMITTER with Integrated Jeti and Futaba

Futaba 12FG 2.4GHz FASST Radio TRANSMITTER with Integrated Jeti and Futaba

Futaba 12FG 2.4GHz FASST Radio TRANSMITTER with Integrated Jeti and Futaba,

This is a custom made , professionally integrated and adapted Jeti system modul, and Jeti box Profi. you can use this radio for any Jeti receiver and Futaba fasst 2.4

THIS Radio was used 2 times,  in perfect condition, with brand new lipo TX battery

Standard  charger included

delivered with TM-14 module, Jeti pre-installed module, Jeti Box profi.

delivered in Carbonite JR case,

-Receiver Not included

€699.00


€577.69 Ex VAT
Quantity
Futaba 12Z 12-Channel 2.4GHz TRANSMITTER With TM-14- Second hand

Futaba 12Z 12-Channel 2.4GHz TRANSMITTER With TM-14- Second hand

Futaba 12Z 12-Channel 2.4GHz TRANSMITTER With TM-14- Second hand

THIS Radio was very little used, but in perfect condition.

Included:

12Z transmitter

2 TX batteries with charger

TM-14 module

R6014 receiver, R608FS receiver

Alu Case, and accessories inside

See more Photos for details

€399.00


€329.75 Ex VAT
Quantity
Futaba 16IZ super 18-Channel FASSTest 2.4 GHz Transmitter with R7208SB Receiver Multimode

Futaba 16IZ super 18-Channel FASSTest 2.4 GHz Transmitter with R7208SB Receiver Multimode

With the Futaba T16iZ Super computer remote control you make the affordable jump to the professional class! The new transmitter design with large color touch display and ergonomically optimized shape guarantees perfect operation of the clear transmitter software. The T16iZ Super supports the established transmission modes T-FHSS, FASSTest and S-FHSS.

The R7208SB receiver supports RX-Link and features antenna diversity.

NEW: In combination with the FUTABA SBS-01ML S.BUS Sensor Adapter (available soon) the transmitter supports the MAVLink protocol. MAVLink or Micro Air Vehicle Link is a protocol for communication with small unmanned vehicles. It is a very simple messaging protocol for communication with drones (and between drone parts on board). MAVLink follows a modern hybrid publish-subscribe and point-to-point design pattern: data streams are sent/published as topics, while configuration sub-protocols such as the mission log or parameter log are point-to-point with retransmission.

With the S-BUS/S.BUS2 servo function, all parameters of S.BUS/S.BUS2 servos can be set individually via the transmitter.

The transmitter is fully equipped with 8 switches, 2 rotary encoders and 2 rear-mounted slide encoders. All controls are ergonomically placed for perfect operation during flight. The ball bearing control sticks impress with their precision and unique adjustability. The spring force and the ratchet function can be adjusted from the outside on the joysticks. Each stick function also features digital trim. The Futaba T16IZ is furthermore equipped with an S.BUS and a headphone connection, as well as a trainer/DSC connection.

The transmitter comes standard with powerful software for motorized aircraft, gliders, helicopters and drones (multicopters). The menu navigation is available in 9 languages. Model & telemetry data can be stored and firmware updates for the transmitter can be imported via the SD card reader integrated into the transmitter.

FASSTest System
The T16IZ SUPER transmitter has  adopted the bidirectional communication system "FASSTest". Data from the receiver can be checked in your transmitter. FASSTest is a maximum 18  channels 2.4GHz dedicated system.

Color Touch LCD Screen
T16IZ

SUPER has an HVGA 4.3", full-color, backlit LCD touch screen. The screen is transflective which enables booth indoor and outdoor visibility.

S.BUS2 System
By using the S.BUS2 system, multiple servos, gyros and telemetry sensors are easily installed with a minimum amount of cables.

Model Types

  • Multicopter
  • Helicopters: 8 different swash plate types are available
  • Airplanes: 7 wing types & 3 tail types are available
  • Functions and mixers necessary for each model type is set in advance at the factory


Lithium-Ion Polymer Battery
T16IS SUPER is operated by a 7.4V/2000mAh Li-Ion polymer battery.

MicroSD Card (not included)
Model data can be saved to a microSD card (SD: 32MB-2GB / SDHC: 4-32GB). When T16IZ SUPER transmitter software files are released, the software can be updated by using a microSD card update.

Edit Buttons
Two edit update buttons are provided and the operating screen can be immediately "Returned" to the HOME screen during operation. Setting operation can be performed easily by combining this button with a touch sensor.

Vibration Function
Selects a function that aerts the operator to various alarms by vibrating the transmitter in addition to sounding a buzzer.

Speech Function
A function which allows the system to provide telemetry data audibly. This function can also be utilized with commercial available earphones.

Compatible receivers (as of March 2023):

  • R7008SB
  • R7208SB
  • R7308SB

Package including:

  • Transmitter T16iZ Super
  • Receiver R7208SB
  • Transmitter battery LiPo 2s 2000 mAh
  • USB charging cable
  • Manual

€699.00


€577.69 Ex VAT
Quantity
FUTABA 18SZ 2.4Ghz Radio + R7214SB RECEIVER multimode

FUTABA 18SZ 2.4Ghz Radio + R7214SB RECEIVER multimode

The new Futaba 18SZ includes an amazing array of features that are sure to please all airplane, helicopter and multirotor pilots. Eighteen channels allow even the most complex of models to be controlled. A large, color LED touchscreen and display simplifies data entry and programming tasks. Additional features include flight conditions, S.Bus servo programming capabilities and several selectable languages. The included Futaba R7008SB FASSTest 8+ channel S.Bus receiver enables bi-directional communication and the use of a variety of Futaba telemetry sensors. The first delivery scheduled at October 2015, orders will be sent our per orders placed.

For many years Futaba have led the way with the ultimate in radio systems, and they have done it again with their new T18SZ.

Packed full of possibilities, the T18SZ includes a Li-Fe battery for extended run times, S-FHSS, T-FHSS, FASST and FASSTest transmission systems, 4.3" colour ultra quick response touch screen, flight conditions, a massive range of mixing and programming options for Aircraft, Gliders, Helicopters and Multirotors, Telemetry, Data Logging, etc, not to mention full 18 channel operation.

Supplied complete with the 8 18 channel R7008SB receiver, the T18SZ is the perfect radio for any serious pilot, and of course the regular software updates provided by Futaba will keep this superb radio up to date.

  • Futaba 2.4GHz FASSTest, FASST, T-FHSS, S-FHSS Modulation
  • 18 Channel (16 Linear + 2 Digital)
  • 30 Internal Model Memory
  • SD Card External Model Memory (SDHC is available.)
  • Telemetry System (Details Below)
  • Voice Message
  • Easy Software Updates using SD card
  • Stick Calibration
  • Ultra-Fast 109mm (4.3") Colour TFT-LCD Touch Screen
  • 2 Front Dials
  • 2 Side Levers
  • 6 Trim Levers
  • 8 Toggle Switch
  • Long life LiFe Battery (LT2F2100B)
  • Antenna Angle Adjustment (90 degree and 3 step Rotation)
  • Built-in Speaker
  • Earphone Jack
  • S.BUS I/F (with Power Supply)
  • Trainer PPM 8CH / PPM 12CH / S.BUS (16CH)
  • Trainer S.BUS Port
  • Adjustable Angle Sticks
  • Built-In Vibrator

Basic Program Features

  • 15 Character User Names
  • 15 Character Model Names
  • Condition Name
  • Function Setting
  • Function Rename (AUX function only)
  • Sub Trim (±240 steps)
  • Servo Reverse
  • Fail Safe
  • Battery Fail Safe (All Channels on FASSTest/FASST-Multi/S-FHSS, 3 Channel FASST 7CH)
  • EPA (30 - 140% with Limit setting)
  • Servo Speed Adjustment
  • Trim Setting (Step, Rate, Mode)
  • Flight Condition (Maximum 8 conditions)
  • AFR (D/R)
  • AFR Curve Mode (3 Types)
  • AFR Curve Point Number (Maximum 17 points)
  • Programmable Mixing (10 per Condition)
  • Throttle Cut
  • Idle down
  • Logic switch (Condition switch only)
  • Data editor for S.BUS equipment
  • Servo Monitor (with NT and Moving Test)
  • 2 Up/Down Timers
  • Integral Timer (System Timer)
  • Model Timer
  • Stick Alarm

Telemetry Options

  • Receiver Battery
  • Temperature Sensor
  • RPM Sensor (Magnetic)
  • RPM Sensor (Optic)
  • Altitude Sensor (with Vario)
  • GPS Sensor (Included Altitude Sensor)
  • Voltage Sensor
  • Current Sensor
  • Voice
  • Data Logging    
Includes:
  • T18SZ Mode-1 transmitter
  • R7214SB Receiver
  • 6.6V LiFe battery & 230V LiFe charger
  • Switch harness
R7214SB Specs:
  • FASSTest-2.4GHz
  • Diversity Antennas
  • Channels: 10ch (PWM) + S.BUS
  • Dual RX-RX Capable
  • S.BUS2
  • Extra External Voltage Port
  • Size: 50.1x36.9x16mm
  • Weight: 18g

€1182.00


€976.86 Ex VAT
Quantity
Futaba 18SZ Radio Mode-2 with R7208SB FASSTest multimode

Futaba 18SZ Radio Mode-2 with R7208SB FASSTest multimode

Futaba closes the gap between middle class and high-end with the T18SZ

The T18SZ is a fully equipped 18-channel transmitter that leaves nothing to be desired in terms of transmission reliability, quality, function and usability. The well-known modulations such as FASST, FASSTest and FHSS were supplemented by the T-FHSS transmission technology so that telemetry operation in FHSS mode is now also possible. The menu navigation is clearly structured and can be quickly operated via the large color touch screen. In addition to the familiar functions of the T-18MZ, a multicopter menu and 9-language menu navigation has been added. The integrated SD card slot for storing model data and software updates for future, new applications makes this remote control future-proof. The built-in speaker, as well as the LiFe rechargeable battery incl. Charger complete the package. The high-quality transmitter housing captivates by its processing quality and lies thereby perfectly in the hand. The ergonomically arranged switches and encoders allow fatigue-free operation and their precision is unique in this price segment.

  • Futaba 2.4GHz FASSTest, FASST, T-FHSS, S-FHSS Modulation
  • 18 Channel (16 Linear + 2 Digital)
  • 30 Internal Model Memory
  • SD Card External Model Memory (SDHC is available.)
  • Telemetry System (Details Below)
  • Voice Message
  • Easy Software Updates using SD card
  • Stick Calibration
  • Ultra-Fast 109mm (4.3") Colour TFT-LCD Touch Screen
  • 2 Front Dials
  • 2 Side Levers
  • 6 Trim Levers
  • 8 Toggle Switch
  • Long life LiFe Battery (LT2F2100B)
  • Antenna Angle Adjustment (90 degree and 3 step Rotation)
  • Built-in Speaker
  • Earphone Jack
  • S.BUS I/F (with Power Supply)
  • Trainer PPM 8CH / PPM 12CH / S.BUS (16CH)
  • Trainer S.BUS Port
  • Adjustable Angle Sticks
  • Built-In Vibrator

Basic Program Features

  • 15 Character User Names
  • 15 Character Model Names
  • Condition Name
  • Function Setting
  • Function Rename (AUX function only)
  • Sub Trim (±240 steps)
  • Servo Reverse
  • Fail Safe
  • Battery Fail Safe (All Channels on FASSTest/FASST-Multi/S-FHSS, 3 Channel FASST 7CH)
  • EPA (30 - 140% with Limit setting)
  • Servo Speed Adjustment
  • Trim Setting (Step, Rate, Mode)
  • Flight Condition (Maximum 8 conditions)
  • AFR (D/R)
  • AFR Curve Mode (3 Types)
  • AFR Curve Point Number (Maximum 17 points)
  • Programmable Mixing (10 per Condition)
  • Throttle Cut
  • Idle down
  • Logic switch (Condition switch only)
  • Data editor for S.BUS equipment
  • Servo Monitor (with NT and Moving Test)
  • 2 Up/Down Timers
  • Integral Timer (System Timer)
  • Model Timer
  • Stick Alarm

Telemetry Options

  • Receiver Battery
  • Temperature Sensor
  • RPM Sensor (Magnetic)
  • RPM Sensor (Optic)
  • Altitude Sensor (with Vario)
  • GPS Sensor (Included Altitude Sensor)
  • Voltage Sensor
  • Current Sensor
  • Voice
  • Data Logging    

Specification

  • Dials:    2
  • Memory:Expandable SD/SDHC Card Slot
  • Mode:Mode 2 or 1.
  • Model Memory:30 (+ SD/SDHC Card)
  • Modulation:Futaba 2GHz FASST, FASSTest, T-FHSS, S-FHSS
  • Receiver:R7008SB 2.4GHz FASSTest (Inc.)
  • S.BUS:    S.Bus & S.Bus2
  • Screen:    109mm (4.3") TFT-LCD Colour Touch Screen (Inc.)
  • Sliders:2
  • Speaker:(Inc.)
  • Switches:8
  • Telemetry:T-FHSS & FASSTest Telemetry + Voice
  • Trims:6
  • Battery:FT2F2100B 2100mAh Li-Fe (Inc.)
  • Channels:18 (16 Full + 2 Switch)

YOUR T18SZ INCLUDES THE FOLLOWING COMPONENTS:

    • T18SZ Mode-2 transmitter
    • R7208SB Receiver
    • 6.6V LiFe battery
    • Switch harness

€1116.00


€922.31 Ex VAT
Quantity
Futaba 4-Way S.Bus Servo Terminal Box Connector Hub Block

Futaba 4-Way S.Bus Servo Terminal Box Connector Hub Block

Futaba 4-Way S.Bus Servo Terminal Box Connector Hub Block

€9.90


€8.18 Ex VAT
Quantity
Futaba 4PV 4-Channel 2.4GHz S-FHSS/T-FHSS Radio System with R304SB Receiver

Futaba 4PV 4-Channel 2.4GHz S-FHSS/T-FHSS Radio System with R304SB Receiver

The Futaba 4PV 4-Channel 2.4GHz S-FHSS/T-FHSS Radio System delivers the best of both worlds for bashers and racers.

The 4PV utilizes Futaba's lightning fast T-FHSS protocol to provide live telemetry data of your vehicle's temperature, RPM, receiver and external voltage levels, without slowing down the response of the transmitter/receiver.

The 4PV is compatible with two T-FHSS receivers and six S-FHSS receivers and can be easily updated via the CIU-2 and CIU-3 interface. This means your 4PV will always be up to date with Futaba's latest technological innovations.

To get the most out of your vehicle and 4PV use the included R304SB T-FHSS receiver.

Other features include audible alerts via audio jack allow you to focus on driving while staying in the know.  Plus, ergonomic adjustments include throttle position, throttle tension, steering tension and 5-optional accessories (not included) that allow you to customize the ergonomics to suit your unique needs and desires.

Features:

  • T-FHSS and S-FHSS protocols
  • Large backlit LCD screen
  • Telemetry functions with logging capabilities and audible alerts
  • Six digital trims
  • 40-model memory
  • 10-character model naming
  • S.Bus/S.Bus2 servo programming
  • Direct Model Select
  • Model Copy/Model Clear
  • Alarm tone adjustments
  • Fail Safe
  • Dial trim step select
  • Data transfer/copy
  • Firmware updatable via CIU-2 or CIU-3
  • Compatible with 2S LiFe batteries, NiMHs, dry cells and other battery options

Specifications:

Transmitter:

  • Type: 4-Channel S-FHSS/T-FHSS*
  • Includes: 3-Channel R304SB Receiver
  • Requires: (4) "AA" alkaline batteries

R304SB Receiver:

  • Type: 4-Channel T-FHSS
  • Input Power: 4.8V-7.4V
  • Dimensions: 1.38 x 0.91 x 0.33 in (35.1 x 23.2 x 8.5 mm)
  • Weight: 0.23 oz (6.6 g)
  • Included in box
  • Transmitter
  • Receiver r304sb

€315.00


€260.33 Ex VAT
Futaba 9Z plug

Futaba 9Z plug

To be used for making Traner or Simulator cables

€7.00


€5.79 Ex VAT
Quantity
Futaba BLS-A600 6.7kg 0.09s HV S.Bus2 High-Performance Brushless Mini Servo

Futaba BLS-A600 6.7kg 0.09s HV S.Bus2 High-Performance Brushless Mini Servo

The Futaba BLS-A600 is a high-performance brushless mini servo designed specifically for RC aircraft. With its compact size, robust construction, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and precision required for demanding flight applications.

Key Features:

  • Torque @ 7.4V: 6.7 kg·cm (93 oz·in)
  • Torque @ 6.6V: 6.0 kg·cm (83.3 oz·in)
  • Speed @ 7.4V: 0.09s/60°
  • Speed @ 6.6V: 0.10s/60°
  • Voltage Range: 4.8V – 7.4V
  • Dimensions: 27.2 × 13.0 × 30.5 mm
  • Weight: 28 g
  • Motor Type: Brushless
  • Case: Resin
  • Gears: Metal gears
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • CIU-2/-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The BLS-A600 is engineered for precision and durability, making it an ideal choice for high-performance RC aircraft enthusiasts seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use with dry batteries or BEC systems. For optimal performance, use a dedicated power supply.

€179.00


€147.93 Ex VAT
Quantity
Futaba BLS-CM600 6.7kg 0.09s HV S.Bus2 High-Performance Brushless Mini Servo

Futaba BLS-CM600 6.7kg 0.09s HV S.Bus2 High-Performance Brushless Mini Servo

The Futaba BLS-CM600 is a high-performance brushless mini servo designed specifically for 1/12 scale RC cars. With its compact size, robust construction, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and precision required for competitive racing.

Key Features:

  • Torque @ 7.4V: 6.7 kg·cm (93 oz·in)
  • Torque @ 6.0V: 5.4 kg·cm (75 oz·in)
  • Speed @ 7.4V: 0.09s/60°
  • Speed @ 6.0V: 0.11s/60°
  • Voltage Range: 4.8V – 7.4V
  • Dimensions: 27.2 × 13.0 × 30.5 mm
  • Weight: 28 g
  • Motor Type: Brushless
  • Case: Resin
  • Gears: Metal gears
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM
  • Signal Modes: UR mode (Ultra Response), SR mode (Super Response)

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • CIU-2/-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The BLS-CM600 is engineered for precision and durability, making it an ideal choice for high-performance RC car enthusiasts seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use with dry batteries or BEC systems. For optimal performance, use a dedicated power supply.

€179.00


€147.93 Ex VAT
Quantity
Futaba BLS174HV 9.6kg 0.09s HV S.Bus High-Performance Brushless Servo

Futaba BLS174HV 9.6kg 0.09s HV S.Bus High-Performance Brushless Servo

The Futaba BLS174HV is a high-performance brushless servo designed specifically for RC aircraft. With its compact size, robust construction, and advanced S.Bus compatibility, it delivers exceptional torque, speed, and precision required for demanding flight applications.

Key Features:

  • Torque @ 7.4V: 9.6 kg·cm (133 oz·in)
  • Torque @ 6.6V: 8.8 kg·cm (122 oz·in)
  • Speed @ 7.4V: 0.09s/60°
  • Speed @ 6.6V: 0.10s/60°
  • Voltage Range: 6.0V – 7.4V
  • Dimensions: 47.5 × 27.0 × 25.4 mm
  • Weight: 53 g
  • Motor Type: Brushless
  • Case: Resin
  • Gears: Nylon gears
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, PWM

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • CIU-2/-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The BLS174HV is engineered for precision and durability, making it an ideal choice for high-performance RC aircraft enthusiasts seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use with dry batteries or BEC systems. For optimal performance, use a dedicated power supply.

€179.00


€147.93 Ex VAT
Quantity
Futaba CGY770R Flybarless Helicopter Gyro Controller w/ GBP-1 Programmer box

Futaba CGY770R Flybarless Helicopter Gyro Controller w/ GBP-1 Programmer box

Futaba CGY770R+GPB-1 -  Equipped with new system [UR mode]! Receiver, built-in governor, 3-axis gyro for helicopters + Programming Box

CGY770R is a 3-axis gyro for helicopters that is equipped with a new system [UR mode] and has a receiver and governor integrated with a wireless tuning function.

System that integrates receiver, 3-axis gyro function, and governor function.

  • The CGY770R replaces the CGY760R.

Features:

  • Includes GPB-1 Programming Box
  • Gyro can also be operated independently
  • Gyro and governor both use the fastest control method
  • Small, low profile, lightweight
  • Can be set using GPB-1 (gyro program box) *When using GPB-1 with CGY770R, it is necessary to update to Ver.5.0 or later.
  • S.BUS2 system compatible
  • Receiver/gyro/governor integrated
  • Equipped with Dual Rx Link system
  • Equipped with sensor response adjustment function
  • Addition of wireless setting items
  • Gyro adjustment menu P, I, and D gains can be adjusted on one screen
  • *GPB-1 setting screen
  • Compatible with new system UR (Ultra Response) mode
  • In combination with a servo compatible with helicopter UR mode, faster response can be obtained.
  • Also, servo update of HPS-HC701 and HPS-HT700 is required. Compatible with Ver.2.0 or later.

*To use UR mode, please use HPS-HC701 or HPS-HT700. *As of 2024/3/15

Setting items are divided into basic and expert menus

  • Basic settings can be made in the basic menu
  • Detailed settings can be made in the expert menu


What is UR mode?

  • UR mode is a system installed in the high-end car transmitter [T10PX].
  • This is Futaba's fastest system, recognized by many top drivers.
  • You can experience the proven fastest system, UR mode, in a helicopter.
  • *UR servos for cars cannot be used.

Specs:

  • 3-axis gyro for helicopters with integrated receiver and governor
  • Control method: Digital advance control
  • Angular velocity detection method: Vibration gyro sensor
  • Angle range: ±1,000°/sec
  • Rotation speed detection method: Engine rotation direct detection by magnetic sensor
  • Control resolution: 0.1 Hz (± 6 rpm: engine rotation speed)
  • Rotation speed stability accuracy: within ± 1%
  • Control rotation speed range: 700 to 4,000 rpm (rotor rotation speed)
  • Antenna: Diversity method
  • Rated power supply voltage range: DC 3.7 V to 7.4 V *(Usable voltage range: 3.5 V to 8.4 V)
  • Current consumption: 85 mA (when receiving, no servo, no RPM sensor)
  • Operating temperature range: -10 to +45℃
  • Operating humidity range: 10 to 90%RH (no condensation)
  • Dimensions: 39.2x27.0x15.0mm
  • Weight: 22.3g

Reception system:

  • FASSTest-2.4 GHz (18 CH/12 CH mode)
  • T-FHSS-Air-2.4 GHz method, S.BUS2 input/output + output for conventional system (CH1-6)

€459.90


€380.08 Ex VAT
Quantity
Futaba CGY770R Flybarless Helicopter Gyro Controller, No Program Box

Futaba CGY770R Flybarless Helicopter Gyro Controller, No Program Box

Futaba CGY770R -  Equipped with new system [UR mode]! Receiver, built-in governor, 3-axis gyro for helicopters

CGY770R is a 3-axis gyro for helicopters that is equipped with a new system [UR mode] and has a receiver and governor integrated with a wireless tuning function.

System that integrates receiver, 3-axis gyro function, and governor function.

  • The CGY770R replaces the CGY760R.

Features:

  • Gyro can also be operated independently
  • Gyro and governor both use the fastest control method
  • Small, low profile, lightweight
  • Can be set using GPB-1 (gyro program box) *When using GPB-1 with CGY770R, it is necessary to update to Ver.5.0 or later.
  • S.BUS2 system compatible
  • Receiver/gyro/governor integrated
  • Equipped with Dual Rx Link system
  • Equipped with sensor response adjustment function
  • Addition of wireless setting items
  • Gyro adjustment menu P, I, and D gains can be adjusted on one screen
  • *GPB-1 setting screen
  • Compatible with new system UR (Ultra Response) mode
  • In combination with a servo compatible with helicopter UR mode, faster response can be obtained.
  • Also, servo update of HPS-HC701 and HPS-HT700 is required. Compatible with Ver.2.0 or later.

*To use UR mode, please use HPS-HC701 or HPS-HT700. *As of 2024/3/15

Setting items are divided into basic and expert menus

  • Basic settings can be made in the basic menu
  • Detailed settings can be made in the expert menu


What is UR mode?

  • UR mode is a system installed in the high-end car transmitter [T10PX].
  • This is Futaba's fastest system, recognized by many top drivers.
  • You can experience the proven fastest system, UR mode, in a helicopter.
  • *UR servos for cars cannot be used.

Specs:

  • 3-axis gyro for helicopters with integrated receiver and governor
  • Control method: Digital advance control
  • Angular velocity detection method: Vibration gyro sensor
  • Angle range: ±1,000°/sec
  • Rotation speed detection method: Engine rotation direct detection by magnetic sensor
  • Control resolution: 0.1 Hz (± 6 rpm: engine rotation speed)
  • Rotation speed stability accuracy: within ± 1%
  • Control rotation speed range: 700 to 4,000 rpm (rotor rotation speed)
  • Antenna: Diversity method
  • Rated power supply voltage range: DC 3.7 V to 7.4 V *(Usable voltage range: 3.5 V to 8.4 V)
  • Current consumption: 85 mA (when receiving, no servo, no RPM sensor)
  • Operating temperature range: -10 to +45℃
  • Operating humidity range: 10 to 90%RH (no condensation)
  • Dimensions: 39.2x27.0x15.0mm
  • Weight: 22.3g

Reception system:

  • FASSTest-2.4 GHz (18 CH/12 CH mode)
  • T-FHSS-Air-2.4 GHz method, S.BUS2 input/output + output for conventional system (CH1-6)

€449.00


€371.07 Ex VAT
Quantity
Futaba CIU-3 USB Programming Interface

Futaba CIU-3 USB Programming Interface

The CIU-3 is a USB interface for communications between Link-supported

devices (such as a S.BUS servo , Gyro and ESC) and Windows computer.

The CIU-3 is an updated version of the CIU-2 in that it does not need any additional Windows driver software to be installed.

Specs:

  • Interface: USB Rev2.0 compliant
  • USB connector: USB Series A connector
  • Operating voltage: 5.0V ±0.2V (USB bus power)
  • Current drain (At connection, idle): 5.8 ±1.7mA
  • Operating environment: Temperature -10 ~ +45℃
  • Dimensions: 18.2 x 56.5 x 9.0 mm
  • Weight: 7.5 g
  • Applicable OS: Windows 

€69.00


€57.02 Ex VAT
Quantity
FUTABA Composite transmitter case Multi use 37x24x16cm black color

FUTABA Composite transmitter case Multi use 37x24x16cm black color

This is a multi-use transmitter bag that fits many different Futaba transmitters. The case is hard plastic and the top and bottom is padded with foam.

Features:

Rugged plastic case

Carry handle

Carry strap

Moveable divider (velcro)

YKK zipper

Included soft transmitter pouch

Size:

Length: 370mm

Width: 240mm

Height: 160mm

€196.30


€162.23 Ex VAT
Quantity
Futaba External Voltage Cable Lead sensor Voltage Return Line 70V R7003SB, R7008SB & R7018SB

Futaba External Voltage Cable Lead sensor Voltage Return Line 70V R7003SB, R7008SB & R7018SB

Futaba External Voltage Cable Lead sensor Voltage Return Line 70V R7003SB, R7008SB & R7018SB

FEATURES

  • Used to connect a Futaba telemetry equipped receiver to an extra voltage port.

INCLUDES

  • Cable, Fuse, Heat Shrink Tube and Instructions, welding needed

SPECIFICATIONS

  • Length: 700 mm

COMMENTS

  • This voltage cable plugs into the R7008SB next to the antenna.
  • This measures the external voltage, such as the battery that is running a motor. The voltage will be displayed in the transmitter as "EXT-VOLT".
  • Maximum voltage is 70 volts.
  • Cable should be cut to desired length, then remove & save 30mm from the positive black line. Next, solder the fuse inline on the positive wire and reattach the section of wire that was previously removed and solder into place. The fuse should be attached as close to the external power supply as possible. Place shrink tubing over the fuse and cover all sodered areas. Shrink the tubing onto the wire with a heat gun. The cables will then be connected to corresponding + & - wires that connect the ESC to the battery and attached using solder and shrink tubing.

Telemetry voltage cable,Futaba FASSTest External Voltage Lead
Futaba External Voltage Cable Lead sensor Voltage Return Line 70V R7003SB, R7008SB & R7018SB

€12.90


€10.66 Ex VAT
Quantity
FUTABA FDLS-1 Dual receiver Interface, double security for your Aircraft

FUTABA FDLS-1 Dual receiver Interface, double security for your Aircraft

With the FUTABA FDLS-1 you double the security in your model by operating two S.BUS / S.BUS2 receivers in parallel. In the event of a problem with the main receiver, the FDLS-1 switches over to the second receiver at lightning speed.

Two S.BUS / S.BUS2 receivers are required to use the FDLS-1.

Both receivers must be of the same protocol when using the FDLS-1 mixing protocols will not allow the FDLS-1 to operate properly.

Technical specifications

Operating voltage: 3.5-8.4V

Length: 225mm

Weight: 6.5g

€83.90


€69.34 Ex VAT
Quantity
Futaba FX36 18-Channel 2.4GHz FASSTest Tx & R7008SB Rx Combo

Futaba FX36 18-Channel 2.4GHz FASSTest Tx & R7008SB Rx Combo

The Futaba FX36 is the flagship among the tray style transmitters and was designed for high level model flying and competition use. This transmitter style is popular across Europe and is often used in pattern and glider flying. This high quality transmitter is built to the highest standard and leaves nothing to be desired in terms of transmission reliability and functionality.

The features and telemetry functions are almost identical to the well-known T18MZ and T14SG transmitters. This set uses Futaba's best quality stick units ST-57 (as used in the T18MZ) to give extremely precise control.

You can transmit on FASST, FASSTest, T-FHSS and FHSS allowing you to pick the right receiver for your model. The menu navigation is clearly structured and can be quickly/easily operated via the large colour touch screen. In addition to the familiar functions of the T18MZ Futaba have added a new multicopter menu and the ability to use up to 9 different language options! The integrated SD card slot allows you to store model data and software updates for future helping to make the FX36 future-proof.

T14SG, T16SZ, T18SZ, FX-22, FX-30 and FX-32 model memories are convertible to FX-36.

The ergonomically arranged switches and encoders allow fatigue-free operation during long flights and the set includes 2 aluminium joystick extensions to adjust to the pilot if needed.

  • Professional 18-channel remote control system
  • Ergonomic transmitter design
  • Professional level stick units (ST-57)
  • Extensive telemetry functions (Similar to T18MZ)
  • New S.BUS functions
  • Model selection, internal memory for 30 models (Expandable via SD card)
  • 15 Character model / user names
  • Modes switchable between FASST, FASSTest, S-FHSS or T-FHSS
  • 9 Language menu navigation
  • 4.3" Colour touch screen (480 x 272px)
  • Telemetry with voice output via loudspeaker or optional headphones
  • 6 Digital trims
  • 6 Switches
  • 2 Rotary dials
  • 2 Linear sliders
  • Graphical servo monitor that displays all servo paths with servo test function
  • Future proof by updating capability via SD card
  • Extensive timer functions
  • Vibration alarm
  • S.Bus port with power support, for programming and logging S.Bus
  • 8 Flight conditions per model memory (like T18MZ)
  • 10 Option mixes
  • AFR 3 modes (Up to 17 points)
  • 13 Wing types, 3 tail types & 8 swashplate options
  • Fully equipped helicopter menu with swash ring, governor, servo travel and speed compensation, throttle limiter
  • 3 curve modes for gas / pitch, up to 17 points possible
  • Fully equipped sailor menu with 13 wing types, 3 tail units
  • Extensive mixer selection for gliders and engine models (like T18MZ)
  • Freely configurable teacher / student channel assignment

Box Contents

  • Transmitter FX36 2.4GHz FASSTest
  • Receiver R7008SB 2.4 GHz FASSTest
  • Large aluminium case
  • Transmitter battery 6.0V 2500mAh Eneloop Pro NiMH
  • Transmitter battery charging cable
  • Switch with charging socket
  • 2 Aluminium joystick extensions (M4 Thread)
  • Neutralization stopper
  • Screwdriver
  • Printed user manual

Required Accessories
NiMH charger

€1550.00


€1280.99 Ex VAT
Quantity
Futaba Heavy Duty Extension Lead 30cm Long made with 22awg 0.35mm2 wire

Futaba Heavy Duty Extension Lead 30cm Long made with 22awg 0.35mm2 wire

These heavy duty extension leads are compatible with all Futaba type plugs and includes gold plated connections with high quality mouldings and wire.

Length of 30cm, made from 22 AWG / 0.35mm2 heavy duty wire.

This is a Heavy Duty Futaba Servo Extension; This extension goes between the receiver and the servo to make the wire longer. On one end of the wire is a male connector and on the other end of the wire is a female connector

€5.00


€4.13 Ex VAT
Quantity
Futaba Heavy-Duty Servo Extension 60cm 22Awg wire

Futaba Heavy-Duty Servo Extension 60cm 22Awg wire

Futaba Heavy-Duty Servo Extension 60cm made from 22 awg wire

€5.00


€4.13 Ex VAT
Quantity
Futaba HPS-A703 66kg 0.12s HV S.Bus2 High-Performance Brushless Servo Airplane

Futaba HPS-A703 66kg 0.12s HV S.Bus2 High-Performance Brushless Servo Airplane

The Futaba HPS-A703 is a high-performance brushless servo designed specifically for giant-scale RC airplanes. With its robust aluminum case, powerful brushless motor, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and precision required for demanding flight maneuvers.

Key Features:

  • Torque @ 7.4V: 66.0 kg·cm (916.61 oz·in)
  • Torque @ 6.6V: 61.0 kg·cm (847.17 oz·in)
  • Speed @ 7.4V: 0.12s/60°
  • Speed @ 6.6V: 0.13s/60°
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 × 21.0 × 39.4 mm
  • Weight: 82 g
  • Motor Type: High-power brushless
  • Case: Full CNC aluminum (top, middle, and bottom)
  • Gears: Stainless steel final gear
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • SBC-1 Servo Programmer
  • CIU-2/-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-A703 is engineered for precision and durability, making it an ideal choice for high-performance RC airplane pilots seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use with dry batteries or BEC systems. For optimal performance, use a dedicated power supply.

€270.00


€223.14 Ex VAT
Quantity
Futaba HPS-A704 14kg 0.06s HV S.Bus2 High-Performance Brushless Servo for F3A

Futaba HPS-A704 14kg 0.06s HV S.Bus2 High-Performance Brushless Servo for F3A

The Futaba HPS-A704 is a high-performance brushless servo designed specifically for F3A class RC airplanes. With its low-profile design, HPS brushless motor, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and precision required for competitive aerobatic flying.

Key Features:

  • Torque @ 7.4V: 14.0 kg·cm (194.4 oz·in)
  • Torque @ 6.6V: 12.5 kg·cm (173.6 oz·in)
  • Speed @ 7.4V: 0.06s/60°
  • Speed @ 6.6V: 0.07s/60°
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 × 21.0 × 26.9 mm
  • Weight: 48 g
  • Motor Type: High-power brushless HPS
  • Case: Plastic (top, middle, and bottom)
  • Gears: Metal gears with high-strength final stage
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • CIU-2/-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-A704 is engineered for precision and durability, making it an ideal choice for high-performance F3A pilots seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use with dry batteries or BEC systems. For optimal performance, use a dedicated power supply.

€232.00


€191.74 Ex VAT
Quantity
Futaba HPS-AA702 41kg@0.075s HV/S.BUS2 Brushless High-Voltage performance Helicopter Servo

Futaba HPS-AA702 41kg@0.075s HV/S.BUS2 Brushless High-Voltage performance Helicopter Servo

High Performance Servo with Brushless Motor (Neutral Pulse Width: Default 1520μs, optional 760μs) 

For all-purpose giant scale airplanes and Helicopters

FEATURES:

  • For all-purpose giant scale airplanes
  • Programmable/HV Brushless Servo
  • Custom New high power Brushless Motor
  • Suggested upgrade for BLS172SV/177SV/AA700
  • Programmable and compatible with S.Bus and S.Bus2 systems
  • Can be connected to a PC using the CIU-2/-3 USB adapter sold separately
  • Final gear material is Stainless Steel
  • Upper/middle/bottom: Aluminum Case


SPECS:

  • SPEED: 0.08 sec/60° @ 6.6V / 0.075 sec/60° @ 7.4V
  • TORQUE: 37 kg/cm @ 6.6V / 41 kg/cm @ 7.4V
  • SIZE: 40.5 x 21 x 39.4 mm
  • WEIGHT: 80 g
  • RATED VOLTAGE: DC 6.0V-7.4V
  • OPERATING VOLTAGE: DC 4.8-8.4V

€259.00


€214.05 Ex VAT
Quantity
Futaba HPS-CB701 Brushless 49kg 0.075s HV High-Performance Servo S.Bus2

Futaba HPS-CB701 Brushless 49kg 0.075s HV High-Performance Servo S.Bus2

The Futaba HPS-CB701 is a high-performance brushless servo designed for 1/8 and 1/10 scale RC cars. With a powerful HV brushless motor and S.Bus2 compatibility, it delivers exceptional speed and torque for competitive racing.

Key Features:

  • Torque: 49kg/cm at 7.4V; 42kg/cm at 6.0V
  • Speed: 0.075s/60° at 7.4V; 0.09s/60° at 6.0V
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 x 21.0 x 37.8 mm
  • Weight: 75g
  • Motor Type: High-power brushless
  • Case: Full aluminum (top/middle/bottom)
  • Gears: Metal gears with high-strength final stage
  • Compatibility: S.Bus, S.Bus2, PWM
  • Supports: SR and UR modes for ultra-fast response

Programmable Functions:

  • Channel assignment
  • Servo direction
  • Soft start (on/off)
  • Fail-safe settings (Hold/Free)
  • Smooth operation toggle
  • Center position adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band setting
  • Travel range adjustment (50–175%)
  • Starting power, damping, and holding power settings

Programming Options:

  • Via SBC-1 servo programmer
  • Via CIU-3 USB PC interface
  • Directly through S.Bus-compatible Futaba transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-CB701 is engineered for precision and durability, making it the ideal choice for serious RC enthusiasts seeking top-tier performance.

Note: Not recommended for use in 1/5 scale vehicles.

€280.00


€231.40 Ex VAT
Quantity
Futaba HPS-CD700 17kg 0.045s HV S.Bus2 High-Performance Brushless Servo for Drift Cars

Futaba HPS-CD700 17kg 0.045s HV S.Bus2 High-Performance Brushless Servo for Drift Cars

The Futaba HPS-CD700 is a high-performance brushless servo designed specifically for 1/10 scale RC drift cars. With its low-profile aluminum case, HPS brushless motor, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and precision required for competitive drifting.

Key Features:

  • Torque @ 7.4V: 17.0 kg·cm (236 oz·in)
  • Torque @ 6.0V: 14.0 kg·cm (194 oz·in)
  • Speed @ 7.4V: 0.045s/60°
  • Speed @ 6.0V: 0.055s/60°
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 × 21.0 × 26.2 mm
  • Weight: 53 g
  • Motor Type: High-power brushless HPS
  • Case: Full CNC aluminum (top, middle, and bottom)
  • Gears: Metal gears with high-strength final stage
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM
  • Signal Modes: 1520 µs (default), SR mode supported (UR mode not supported)

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • SBC-1 Servo Programmer
  • CIU-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-CD700 is engineered for precision and durability, making it an ideal choice for high-performance RC drift car enthusiasts seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use in 1/5 scale vehicles.

€267.00


€220.66 Ex VAT
Quantity
Futaba HPS-CT501 21kg 0.06s HV S.Bus2 High-Performance Brushless Servo for RC Cars

Futaba HPS-CT501 21kg 0.06s HV S.Bus2 High-Performance Brushless Servo for RC Cars

The Futaba HPS-CT501 is a high-performance brushless servo designed specifically for 1/10 scale RC cars. With its low-profile design, HPS brushless motor, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and precision required for competitive racing.

Key Features:

  • Torque @ 7.4V: 21.0 kg·cm (291.6 oz·in)
  • Torque @ 6.0V: 17.1 kg·cm (237.5 oz·in)
  • Speed @ 7.4V: 0.06s/60°
  • Speed @ 6.0V: 0.07s/60°
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 × 21.0 × 26.9 mm
  • Weight: 44 g
  • Motor Type: High-power brushless HPS
  • Case: Resin (top, middle, and bottom)
  • Gears: Metal gears with high-strength final stage
  • Bearings: Triple ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM
  • Signal Modes: SR mode (Super Response), UR mode (Ultra Response)

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • SBC-1 Servo Programmer
  • CIU-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-CT501 is engineered for precision and durability, making it an ideal choice for high-performance RC car enthusiasts seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use in 1/5 scale vehicles. Avoid using with dry batteries or BEC systems; use a dedicated power supply for optimal performance.

€224.00


€185.12 Ex VAT
Quantity
Futaba HPS-CT702 Low Profile 30kg@0.07s HV Brushless Servo S.Bus2

Futaba HPS-CT702 Low Profile 30kg@0.07s HV Brushless Servo S.Bus2

The Futaba HPS-CT702 is a high-performance, low-profile servo designed for 1/10 scale RC cars. With a powerful HV brushless motor and S.Bus2 compatibility, it delivers exceptional speed and torque for competitive racing.

Key Features:

  • Torque: 30kg/cm at 7.4V; 23kg/cm at 6.0V
  • Speed: 0.07s/60° at 7.4V; 0.08s/60° at 6.0V
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 x 21.0 x 26.2 mm
  • Weight: 53g
  • Motor Type: High-power brushless
  • Case: Full aluminum (top/middle/bottom)
  • Gears: Metal gears with high-strength final stage
  • Compatibility: S.Bus, S.Bus2, PWM
  • Supports: SR and UR modes for ultra-fast response

Programmable Functions:

  • Channel assignment
  • Servo direction
  • Soft start (on/off)
  • Fail-safe settings (Hold/Free)
  • Smooth operation toggle
  • Center position adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band setting
  • Travel range adjustment (50–175%)
  • Starting power, damping, and holding power settings

Programming Options:

  • Via SBC-1 servo programmer
  • Via CIU-3 USB PC interface
  • Directly through S.Bus-compatible Futaba transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-CT702 is engineered for precision and durability, making it the ideal choice for serious RC enthusiasts seeking top-tier performance.

Note: Not recommended for use in 1/5 scale vehicles.

€295.00


€243.80 Ex VAT
Quantity
Futaba HPS-H700 42kg 0.06s HV S.Bus2 Brushless Helicopter Digital Servo

Futaba HPS-H700 42kg 0.06s HV S.Bus2 Brushless Helicopter Digital Servo

The Futaba HPS-H700 is a premium high-performance servo specifically engineered for the extreme demands of modern 3D and F3C RC helicopters. Combining cutting-edge brushless motor technology with lightning-fast response and massive torque, it’s the top-tier choice for demanding pilots.

Key Features:

  • Torque: 42 kg/cm @ 8.4V
  • Speed: 0.06 sec/60° @ 8.4V
  • Voltage Range: 6.0 – 8.4V (HV Compatible)
  • Motor: High-efficiency Brushless
  • Communication: Futaba S.Bus2
  • Gears: High-precision metal gear train
  • Case: CNC-machined aluminum middle case for optimal cooling
  • Dimensions: 40.5 × 21 × 38.1 mm
  • Weight: 78 g

Delivered With:

  • Servo horns
  • Mounting hardware

Engineered to handle the brutal torque loads of high-performance helicopters, the HPS-H700 delivers ultra-fast, ultra-consistent response for precise cyclic control. Designed for use with Futaba's advanced S.Bus2 system and operating flawlessly under HV conditions, it ensures total flight confidence in any maneuver.

€221.00


€182.64 Ex VAT
Quantity
Futaba HPS-H701 40kg 0.07s High Voltage S.Bus2 High-Performance Brushless Servo

Futaba HPS-H701 40kg 0.07s High Voltage S.Bus2 High-Performance Brushless Servo

The Futaba HPS-H701 is a high-performance brushless servo designed for large RC helicopters. With a powerful HV brushless motor and S.Bus2 compatibility, it delivers exceptional speed and torque for demanding applications.

Key Features:

  • Torque: 40kg/cm at 7.4V; 36kg/cm at 6.6V
  • Speed: 0.07s/60° at 7.4V; 0.075s/60° at 6.6V
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 x 21.0 x 37.8 mm
  • Weight: 76g
  • Motor Type: High-power brushless
  • Case: Full aluminum (top/middle/bottom)
  • Gears: Metal gears with titanium final stage
  • Compatibility: S.Bus, S.Bus2, PWM
  • Supports: 760μs and 1520μs pulse widths

Programmable Functions:

  • Channel assignment
  • Servo direction
  • Soft start (on/off)
  • Fail-safe settings (Hold/Free)
  • Smooth operation toggle
  • Center position adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band setting
  • Travel range adjustment (50–175%)
  • Starting power, damping, and holding power settings

Programming Options:

  • Via SBC-1 servo programmer
  • Via CIU-3 USB PC interface
  • Directly through S.Bus-compatible Futaba transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-H701 is engineered for precision and durability, making it the ideal choice for serious RC helicopter enthusiasts seeking top-tier performance.

Note: Not recommended for use in 1/5 scale vehicles.

€273.00


€225.62 Ex VAT
Quantity
Futaba HPS-HC700 S.bus 2 Brushless High Performance Servo with Brushless Motor 1520μs,optional 760μs

Futaba HPS-HC700 S.bus 2 Brushless High Performance Servo with Brushless Motor 1520μs,optional 760μs

The Futaba HPS-HC700 is a high-performance brushless servo designed for RC helicopters. With a powerful HV brushless motor and S.Bus2 compatibility, it delivers exceptional speed and torque for demanding applications.

Key Features:

  • Torque: 20kg/cm at 7.4V; 18kg/cm at 6.6V
  • Speed: 0.08s/60° at 7.4V; 0.09s/60° at 6.6V
  • Voltage Range: 6.0V – 7.4V
  • Dimensions: 40.5 x 21.0 x 37.8 mm
  • Weight: 73g
  • Motor Type: High-power brushless
  • Case: Full aluminum (top/middle/bottom)
  • Gears: Metal gears with high-strength final stage
  • Compatibility: S.Bus, S.Bus2, PWM

Programmable Functions:

  • Channel assignment
  • Servo direction
  • Soft start (on/off)
  • Fail-safe settings (Hold/Free)
  • Smooth operation toggle
  • Center position adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band setting
  • Travel range adjustment (50–175%)
  • Starting power, damping, and holding power settings

Programming Options:

  • Via SBC-1 servo programmer
  • Via CIU-3 USB PC interface
  • Directly through S.Bus-compatible Futaba transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-HC700 is engineered for precision and durability, making it the ideal choice for serious RC helicopter enthusiasts seeking top-tier performance.

Note: Not recommended for use in 1/5 scale vehicles.

€219.00


€180.99 Ex VAT
Quantity
Futaba HPS-HC701 30kg 0.07s HV S.Bus2 High-Performance Brushless Servo

Futaba HPS-HC701 30kg 0.07s HV S.Bus2 High-Performance Brushless Servo

The Futaba HPS-HC701 is a high-performance brushless servo designed specifically for 500 to 800 class RC helicopters. With its low-profile aluminum case, HPS brushless motor, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and response required for 3D and F3C flying.

Key Features:

  • Torque @ 7.4V: 30.0 kg·cm
  • Torque @ 6.6V: 26.5 kg·cm
  • Speed @ 7.4V: 0.07s/60°
  • Speed @ 6.6V: 0.08s/60°
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 × 21.0 × 26.2 mm
  • Weight: 54 g
  • Motor Type: High-power brushless HPS
  • Case: Full CNC aluminum (top, middle, and bottom)
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM
  • Signal Modes: 760 μs (default), switchable to 1520 μs via GPB-1 (v4.3+)

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 μs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • SBC-1 Servo Programmer
  • CIU-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-HC701 is engineered for precision and endurance, making it an ideal choice for high-performance RC helicopter pilots seeking top-tier servo performance with fast response and high torque.

Note: Not recommended for use in 1/5 scale surface vehicles.

€273.00


€225.62 Ex VAT
Quantity
Futaba HPS-HT700 9.6kg 0.045s HV S.Bus2 High-Performance Brushless Tail Low Profile Servo

Futaba HPS-HT700 9.6kg 0.045s HV S.Bus2 High-Performance Brushless Tail Low Profile Servo

The Futaba HPS-HT700 is a high-performance brushless tail servo designed specifically for 500 to 800 class RC helicopters. With its low-profile aluminum case, HPS brushless motor, and advanced S.Bus2 compatibility, it delivers exceptional torque, speed, and response required for 3D and F3C flying.

Key Features:

  • Torque @ 7.4V: 9.6 kg·cm (133.3 oz·in)
  • Torque @ 6.6V: 8.6 kg·cm (119.4 oz·in)
  • Speed @ 7.4V: 0.045s/60°
  • Speed @ 6.6V: 0.05s/60°
  • Voltage Range: 4.8V – 8.4V
  • Dimensions: 40.5 × 21.0 × 26.2 mm
  • Weight: 54 g
  • Motor Type: High-power brushless HPS
  • Case: Full CNC aluminum (top, middle, and bottom)
  • Bearings: Dual ball bearings
  • Compatibility: S.Bus, S.Bus2, PWM
  • Signal Modes: 760 µs (default), switchable to 1520 µs via GPB-1 (v4.3+)

Programmable Functions:

  • Channel assignment
  • Servo direction reversal
  • Soft start toggle
  • Neutral point adjustment (±300 µs)
  • Speed adjustment (0.39 – 9s per 45°)
  • Dead band tuning
  • Travel range adjustment (50–175%)
  • Start power, damping, and holding power settings

Programming Options:

  • SBC-1 Servo Programmer
  • CIU-3 USB PC Interface
  • Directly via compatible Futaba S.Bus transmitters

Delivered With:

  • Servo Horns
  • Mounting Hardware

The HPS-HT700 is engineered for precision and endurance, making it an ideal choice for high-performance RC helicopter pilots seeking top-tier tail servo performance with fast response and high torque.

Note: Not recommended for use in 1/5 scale surface vehicles.

€273.00


€225.62 Ex VAT
Quantity
Futaba R2006GS Receiver 2.4GHz S-FHSS (Air)

Futaba R2006GS Receiver 2.4GHz S-FHSS (Air)

Small, lightweight 2.4 GHz FHSS six-channel receiver incorporating Frequency Hopping technology.

The Futaba R2006GS 6 channel SFHSS receiver is compatible with the Futaba 6J and 8J radios. This receiver will also work with the Futaba 14SG radio since the 14SG will work with FASST, FHSS, and FASSTest receivers. This receiver works with normal voltage or high voltage applications (4.8 - 7.4V) so you can use a standard ESC, BEC, SBEC, UBEC or you can power it from an external battery pack. This receiver is a frequency hopping spread spectrum design which means it it constantly changing channels looking for the most clear signal possible. Includes a dual diversity antenna.

Not compatible with FASST transmitters. Only for FHSS systems such as T2PL, T3PL, T4YF, T4PL, T6JG)
Not recommended for large-scale model aircraft and jets.

Range: Full
Modulation: FHSS / S-FHSS
Dimensions: 43 x 25 x 8.8 mm
Voltage: 4.8-7.4 V
Current: 40 ma
Dual Diversity Antenna

€49.90


€41.24 Ex VAT
Quantity
Futaba R2008SB 2.4GHz FHSS/S-FHSS 8ch S-bus receiver

Futaba R2008SB 2.4GHz FHSS/S-FHSS 8ch S-bus receiver

Compact eight-channel FHSS/S-FHSS receiver, compatible with all FHSS and S-FHSS systems in the Futaba range. Also includes High Response mode for digital servos. Fail-safe settings are possible for all channels. As a special feature this receiver offers an S.BUS socket for up to eight S.BUS servos or other devices, in addition to the eight PWM servo outputs. Easy-Link button for simple binding to the transmitter.

The Futaba R2008SB is a full range 8 channel receiver with built in S-Bus functionality. It also comes equipped to handle high voltage applications (up to 7.4v).

  • High-voltage operation.
  • Frequency-hopping Spread Spectrum design.
  • Dual Antenna Diversity.
  • S.Bus compatibility
  • 2.4GHz S-FHSS / FHSS auto-detect
  • 8 channels + S.BUS
  • Power feed: 4.8-7.4V
  • Size: 42.8 x 24.9 x 14 mm

€67.00


€55.37 Ex VAT
Quantity
FUTABA R3004SB 2,4 GHz T-FHSS Receiver (S-Bus & HV)

FUTABA R3004SB 2,4 GHz T-FHSS Receiver (S-Bus & HV)

The Futaba R3004SB is a slim 4-channel receiver that is ideally suited to smaller models, as well as gliders/electric gliders that still require full range transmission. Futaba ditched bulky moulded cases and opted for lightweight heat shrink instead, this provides protection for almost any use but helps keep the weight down to just under 5 grams. The electronics are uncompromised, so the R3004SB has full telemetry features and full range transmission. It's slim and compact format makes it ideal for almost any application, whilst a pair of coaxial aerials provide solid stable reception with their length allowing them to be positioned at 90 degrees from each other, to give the maximum possible range.

Features:

  • 2.4GHz T-FHSS Air system
  • 4 Channels + S-BUS
  • S-BUS2 Port for telemetry
  • Diversity Dual Antenna
  • Ultra small design for smaller models
  • Heat shrink enclosure to reduce weight

Specifications:

  • Modulation: T-FHSS Air
  • Weight: 4.8g (0.17 oz)
  • Voltage: 4.8 - 7.4V
  • Channels: 4 + S.Bus2 Port
  • Dimensions: 18 x 41.4 x 9.9mm (0.71 x 1.63 x 0.39")
  • Frequency: 2.4GHz
  • Aerial Length: 2x 150mm

€57.90


€47.85 Ex VAT
Page of 3