RCDistri

2 pin LOCKING Connector

2 pin LOCKING Connector

Set of Male+Female with 15cm wire attached.

  • Locking device, patented.
  • Use is where you want to be safe your battery doesnt disconnect in flight.


€4.00

Inc. VAT
Quantity
Anti static Voltage Detector

Anti static Voltage Detector

This detector designed for electrical and Electro static testing

Easily and safely test for power with this GK7 non-contact voltage detector.
The GK7 has a working range of 70 VAC - 1000 VAC and is perfect for job sites everywhere!

This tool can save you Hundreds of Euros $$$, by helping you to solve electro static sources on your heli.

Find bad bearings, problem with belt, all turning parts which creating electrostatic energy. this one destroying ESC, receivers and resulting crashes and damage..

Use the tool to find out if and where you have the electrostatic electricity on your heli, then use Antistatic spray to remove it.

This tool is a MUST TO HAVE!!!

  •   Non-Contact AC detecting from 90V to 1000VAC
  •   This instrument is only used to judge whether the conductivity is live or not.
  •   LED flash and continual beep when near an AC Voltage source


Product Specification:

  •   Voltage Sensitivity: 90~ 1000VAC
  •   Bandwidth: 50/60Hz
  •   Normal Indicators: Beep and flashing LED indicate the presence of AC and static voltage
  •   Battery Indication: The LED Will not flash if the batter is less than 2V. The beep sounds still on but may be weaker.
  •   Portable design
  •   Easy to use
  •   Safe
  •   Plastic tip over contact point for safety
  •   Audible alert with flashing LED
  •   70 VAC - 1000 VAC detection range
  •   50/60 Hz frequency range
  •   Perfect on-site tool
  •   Runs on two (2) AAA batteries (included)
  •   Pocket clip
  •   CAT III
  •   Test voltage on sockets or cords

Included:

  •   Non-Contact AC Voltage Detector x 1
  •   1.5V Battery (AAA) x 2
  •   English Manual x 1

€12.00

Inc. VAT
Quantity
Body clips Small size fit 1:10 scale, Metal green color (10 pcs)

Body clips Small size fit 1:10 scale, Metal green color (10 pcs)

Body clips

  • 10 pieces in one set
  • small size

€4.50

Inc. VAT
Quantity
Boom Support Bridge

Boom Support Bridge

Tail Support Bridge , a Must for your heli. Stop vibrations of Boom support .

Fits 6-8mm supports.

€7.50

Inc. VAT
Quantity
Custom made TITAN DC5 w/ DJI Air Unit BNF Build-in DJI FPV HD Goggles FPV Racing Combo

Custom made TITAN DC5 w/ DJI Air Unit BNF Build-in DJI FPV HD Goggles FPV Racing Combo

TITAN DC5 w/ DJI Air Unit BNF features the amazing new DJI FPV system, this quad makes flying FPV truly breathtaking. With the 720p video shown at 120fps through the goggles, DJI has set the bar at a new high for clarity and image quality in an FPV system. This TITAN DC5 BNF is 5 inch quad which is no prop in view, equipped SucceX-D F7(50A 4-in-1 ESC) Stack and popular XING motor, everything you just need to bind and fly!

This is a custom built machine, see detailed images for correct motor/etc.

You can use Any radio you want, you will need to add your receiver and bind and calibrate it.
 
FEATURES

  • Build-in DJI Receiver
  • No props in the view, and everything you need to bind and fly!
  • Optimized weight distribution: DJI unit and Stack centered
  • Equipped with SucceX-D F7(50A 4-in-1 ESC) Stack
  • Equipped with the DJI FPV Air Unit -Bind and Fly
  • Buttery-smooth 720p 120fps FPV feed
  • Pre-tuned with smooth freestyle settings
  • Full 3K Carbon Fiber airframe with chamfered arms
  • XING CAMO X2207 2-6S FPV NextGen Motor
  • Special 3d PRINTED ant holder
  • Weight:390g without battery

FRAME // TITAN DC5 V1.4:

  • Weight :116g
  • Wheelbase: 222mm
  • Main body dimension: 185*133mm
  • Bottom to top distance: 35mm
  • Arm thickness: 6mm
  • Bottom plate thickness: 3mm
  • Top plate thickness: 2.5mm
  • Camera plate thickness: 1.5mm( 2.5mm included TPU inserts)

• Universal USB Type C connector instead of micro USB
• Plug-and-Play. No need to solder tiny wires
• Designed to support DJI Digital FPV.
 
BNF // Parts lists

  • 1x TITAN DC5 HD Frame
  • 1x DJI Digital HD FPV Air Unit (FPV Camera/Air Unit Module-DJI FPV Googles)
  • 1x TPU Bracket for DJI Air Unit Module
  • 1x TPU Antenna holder for DJI antenna
  • 2x TPU camera side plate soft mount
  • 1x  Lipo Strap
  • 2x Nazgul 5140 Propeller (Set of 4 Color May Vary)
  • 4x XING CAMO X2207 2-6S FPV NextGen Motor
  • 1x Iflight RC SucceX-D F7 Stack (F7+50A ESC) flight controller
  • 2x DJI FPV Air Unit Antenna (MMCX 90° Pair) (From Air Unit Packaging)

Optional- Radio AT9 with receiver

€1499.00

Inc. VAT
Quantity
Gas Fuel Filter Assembly

Gas Fuel Filter Assembly

Fuel filter assembly for all GAS application. Fits inside gas tank

€7.00

Inc. VAT
Quantity
Multi copter Landing gear 250mm

Multi copter Landing gear 250mm

Foldable LANDING gear, made from Carbon, comes with special attachment for Camera mount

Height, 250mm

€99.00

Inc. VAT
Quantity
Multi copter Landing gear 300mm

Multi copter Landing gear 300mm

Foldable LANDING gear, made from Carbon, comes with special attachment for Camera mount

Height, 300mm

€139.00

Inc. VAT
Quantity
Multi copter Landing gear 350mm

Multi copter Landing gear 350mm

Foldable LANDING gear, made from Carbon, comes with special attachment for Camera mount

Height, 350mm

€159.00

Inc. VAT
Quantity
Robbe Aftermarket Main Shaft Futura, Millenium, Cuatro

Robbe Aftermarket Main Shaft Futura, Millenium, Cuatro

This is an aftermarket Main shaft S4648 for Robbe helicopters as Millenium, Futura, Cuatro, Dyna-X.

those shafts are identical to Robbe S4648.

Set of 1pcs.

€16.00

Inc. VAT
Quantity
TITAN DC5 HD v1.4 5 Inch 222mm Compitable with DJI Air Unit frame Kit

TITAN DC5 HD v1.4 5 Inch 222mm Compitable with DJI Air Unit frame Kit

The TITAN DC5 HD frame perfectly match the amazing new DJI FPV system, this quad makes flying FPV really breathtaking. Electronics optional Characteristics:
  •  Popular Deadcat style configuration, n
  •  Optimized weight distribution: DJI unit and stack centered
  •  Suitable for both 30.5x and 20x stacks
  •  Full 3K carbon fiber airframe with beveled arm
  •  222mm wheelbase, weight: 116g dry weight without TPU parts
Specifications:
  • Weight: 132.3 (with TPU parts and nonslip battery pads)
  • Wheelbase: 222mm
  •  Main body size: 185 * 133mm
  •  Distance from bottom to top: 35 mm
  •  Arm thickness: 6 mm
  •  Bottom plate thickness: 3 mm
  •  Top plate thickness: 2.5 mm
  •  Camera plate thickness: 1.5mm (2.5mm including TPU inserts)
  •  Mounting holes: 30.5 * 30.5mm
  •  Camera Size Support: 19 * 19mm 22 * ​​22mm
  •  Recommended engines: 22xx, 23xx
Package included:
  • 1 x TITAN DC5 HD frame
  • 1 x Screw bag
  • 1 x TPU camera mount adapters
  • 4 x Arm Guard / Motor Mount
  • 1 x TPU DJI bracket mount for air unit
  • 1 x TPU DJI Antenna Holder for Air Unit
  • 1 x TPU protection plate front bottom plate
  • 1 x TPU bottom plate rear protective mount
  • 1 x Battery antislip mat
  • 2 x battery straps

€75.00

Inc. VAT
Quantity
Vertical Fuel Pump

Vertical Fuel Pump

Vertical Pump, with Base.

Works from a 12V power source Alligator style battery clips, Fill-off-empty switch positions.
For use with glow fuel only

€16.00

Inc. VAT
Quantity
Xtreme Production High Quality Motor Pinion 10T (2.0 mm hole)

Xtreme Production High Quality Motor Pinion 10T (2.0 mm hole)

Xtreme Production High Quality Motor Pinion 10T (2.0 mm hole)

Fits Helis up to 250 size

€2.90

Inc. VAT
Quantity