QuickUk

This "economy" spanner set includes just about all the sizes you will ever need on a model heli.
Ideal for you field box and building bench.

Sizes included are : 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm.
Set of 10 spanners

Suitable for ALIGN TRX-600 Nitro & Electric

Lightweight alloy tail clamp for 3D pilots, positive split clamping system with increased surface contact area for a secure fitment. There is no horizontal tail plane mounting provision on this clamp saving weight and further reducing aerodynamic drag.

The clamp itself despite being machined from alloy is 9% lighter than the original plastic two piece clamp. With the carbon tailplane used on the Nitro this gives a 6g weight reduction and on the plastic fin used on the Electric an 11g reduction.

Supplied complete with high tensile socket fixing screws and available in both black and silver finishes.

Component weight 5.2g

Ball bearing Shims 7x10x0.2mm, pack of 10

Preloading your ball bearing system eliminates the extra clearance between the inner race and outer race of the bearing, allowing for smoother mechanical operation. Excessive or insufficient preload, however, can cause more damage than good.

Inner race and outer race bearing shims come in varying thicknesses to help you achieve the right amount of axial preload for your bearings. When installed correctly, bearings shaft shims help prevent misalignment, reduce noise and vibration, improve system rigidity, and extend bearing life. A versatile design also allows use as shaft spacers to align and adjust the spacing between two components.

Specially made for bearings. this washer is stainless and will fir without extra friction on the bearing.

Size : Inner diameter M3, outer diameter 6 MM, thickness  1MM

Pack contains 10 washers

RAPTOR 30/50 V1 & V2These control levers are both strong and light and perfect for the high control loads encountered during demanding 3D style flying particularly with 46/50 powered machines swinging 600mm blades. Machined from solid and fitted with extra wide (5mm each) twin bearings for zero side movement and high durability. Control balls are hardened steel with M3 fixing threads and come pre-installed along with a pair of socket cap style mounting screws.

CNC ends set(caps), for 8mm tubes.

Include 4 pcs, silver Anodized color

*If you need to order the carbon tubes, please order 2 pcs of 8mm
 

CNC Machined Alloy 35 mm Servo Wheel (HiTec fitting)

Heavy duty machined alloy 35mm diameter servo wheel provides positive flex free control and a high degree of structural security. All holes drilled and threaded to accept M2 fixings.

A total of 24 holes at 11mm, 12.5mm, 14mm & 15.5mm from centre allowing various offsets and spacings.

An elegant solution to the problem of oil waste dripping from exhaust systems during transit / storage.

Use these exhaust plugs to prevent dripping oil and also to help seal the exhaust / engine internals from damaging corrosive moisture whilst the model is being stored.Available in 10mm and 12mm internal bore size on silicone rubber exhaust deflectors. Complete with O-Ring seal and easy pull ring for quick removal.

Twin 8mm diameter Carbon fibre boom support set with high quality alloy CNC machined end fittings for superior strength and durabaility. For all 60-90size helis

Stainless steel control ball with M3 thread 4MM long, and 2.0mm internal hexagon drive.
Ball centre to mounting face distance = 4mm
Supplied in a pack of 5 pieces

Stainless steel control ball with M3 thread 6MM long, and 2.0mm internal hexagon drive.
Ball centre to mounting face distance = 4 mm
Supplied in a pack of 5 pieces

Stainless steel control balls /Studs with M3 thread (3/6 mm long) and 2.0mm internal hexagon drive

Ball centre to mounting face distance = 6mm

Supplied in a pack of 5 pieces

Stainless steel control balls /Studs with M3 thread (3/6 mm long) and 2.0mm internal hexagon drive

Ball centre to mounting face distance = 6mm

Supplied in a pack of 5 pieces

Stainless steel control ball with M3 thread 8MM long, and 2.0mm internal hexagon drive.
Ball centre to mounting face distance = 6/8mm
Supplied in a pack of 5 pieces

Push-Pull type alloy throttle arm suitable for the Thunder Tiger Red-Line 53 helicopter engine, a direct replacement for the original plastic arm.
Black color

Heavy duty machined alloy servo disc set specifically for the ROBAN 700/800 class mechanics.

20mm diameter with multiple M2 fixing holes at 8mm from centre to provide ideal geometry.

Pack of 3 (Futaba / Align Fitting)

Stainless Steel Control Ball 8 mm long + M3 short thread

Supplied in a pack of 5 pieces

Replacement Ball link for Eolo Metal swashplate

RAPTOR 30/50 - V1 & V2
Machined from solid alloy, this tail boom brace and fin mounting clamp offers a secure fitting for all types of carbon or glass tail fins. The positive split clamping system provides great rigidity for boom braces compared to the original plastic clamp.

An absolute MUST for any beginner.
This durable training undercarriage uses high impact glass fibre struts with high visibility balls to give your model a a wide, stable base and aid orientation.
Supplied complete with all required fittings.

A set of machined alloy push-pull servo wheels optimised for the Trex 600/700 CCPM system.

Set of 3 wheels with a choice of 5 different control ball positions enabling the closest mechanical servo centre to be used and so minimising sub-trim requirement. Mounting holes are M2 threaded to provide a secure fixing for control balls.

Replacement main blade grip control balls with re-sized ball suitable for use with "standard" 3/16" control ball links such as "Rocket City" or Quick UK.

These are NOT suitable for use with original Align ball links.

Supplied as a pair

Alloy washout base features precision reamed brass sleeve for a smooth and long lasting slide action. A direct replacement for the standard plastic part