Mikado

New processor: 500 MHz (NEO: 98 MHz), more memory, FPU, highest available computing power on the market to this date

Innovative step-up/step-down voltage supply from 2 V up to 16 V at full power with high efficiency (less excess heat)

Full telemetry and range down to 2 V supply voltage

Improved high frequency technology for high power and sensitivity

Double sensor system using tried and tested technology and new sensors

The hardware allows for new specs:

Frame rates adjustable up to 1 kHz (1 ms) on the swash plate and 0.5 ms on the tail

ESC frame rate up to 1 KHz

Pulse width selectable between 1.5 ms down to 125 µS as well as digital high speed protocols

Improved algorithms: adjusted tot he new frame rates, new optimized digital filtering

Dynamic swash plate rotation (per bank)

New „Tail Torque Extension“ for motor driven tails, more control when the tail rotor is unloaded

NEW: Mikado VBar Evo+ Full Digital Gimbals Transmitter Arctic Silver

The TX comes with 7000 mah BATTERY, if you wish to upgrade to 14,000mah, please choose the option. Please take 2-3 days extra delay due the replacement

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

NEW: Fully digital gimbals

• Tough yet lightweight design
• High precision readout with 8 parameters per axis
• 3D sensor sampling (3 Hall sensors per axis)
• Fully integrated in VBar Control EVO software
• all-digital signal path, drift-free
• virtually latency-free
• supreme resolution
• perfectly linear
• temperature compensation per sensor
• earth magnetic field compensation
• super sensitive throughout the whole stick range
• factory calibrated
• adjustable stick response from smooth to extremely fast
• Made in Germany
  
  VBar Control EVO Highlights

• New processor: 600 MHz (Touch: 150 MHz), current chip production
• Latest technology ARM Cortex M7 with large caches and low power consumption
• Graphics processor (GPU)
• Internal flash disk 4 GB (Touch: 128 MB)
• Faster WIFI 802/b/g/n (3 times faster than before), very fast connection
• USB data transfers 10 times faster
• Improved Touch Display
• USB-C fast charging with 15 W with any off-the-shelf USB-C charger
• Extra fast and extra precise reaction to stick inputs due to faster processing

Note: The use of the VBar Control radio requires a VBar EVO or NEO or an RX Satellite with a legacy VBar or Mini-VBar unit with firmware version 6.0 PRO or higher. This version is free for all legacy devices as an incentive (but not for VBar EVO or VBar NEO), for anyone who purchases a VBar Control radio.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models.
• Easy ESC programming of many current ESCs directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functionality (e.g. for archiving, to manage model photos; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar EVO and VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).
  
  Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in one second.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Mikado Vbar Metal rotating knobs, black (2 pc.), VBar Control

Mikado VBar NEO VBasic Receiver

VBar NEO VBasic (VBasic) is an innovative receiver for VBar Control, setting new standards with regard to range of features, and fit for the future with updates and function extensions.

Features:

• Easy setup via VBar Control Setup Wizard and clearly structured menus in VBar Control
• Using Presets and the Setup Wizard you get ready for flight quickly—for almost any application, like R/C-cars, boats, planes, jets, as a receiver for a multi-rotor flightcontrol, as a receiver for other flybarless systems
• Competition-ready since it does not use gyros
• 5 analog control functions and programmable switching functions
• 9 physical outputs (servo connectors)
• 3 parameter banks (flight modes/-conditions)
• 6 mixers with 5 inputs, differential mix, servo-throw adjustment, servo-travel limit
• expo, trims and multi-rate per parameter bank and control input
• throttle channel with idle trim (via rotary knob) and throttle idle for each parameter bank
• innovative, self-learning trim concept without help of gyros (trim while you control the model), optional trim by means of rotary knobs, EDS dial on VBar Control
• Buddy-boxing ready, also cross-over-buddy-boxing ready (VBar Control together with a radio of a different brand)
• Model Sharing (bind and fly)
• Ready for VBar Control telemetry sensors or ­Kontronik® TelMe
• Event Log
• Macrocells offer freely programmable mixers, 7-point curves, sequencers e.g. for retracts
• Multiprotocol Single Line Receiver: connect to other systems via proprietary or open protocols like Futaba® S.Bus, Spektrum® satellite protocol simulation, Universal Digital Interface (UDI), analog PPM8 or PPM12 (8/12 channels), with variable update rate, both as input and output possible
• Connect multiple VBasic and/or VBar NEO devices via Interbus to get a multi-redundant diversity receiver setup (up to 4 diversity receivers/8 antennae), with up to 23 physical outputs (servo connectors)
• Ready for updates as they come available—with software updates you can enable VBasic for other purposes, for more complex airplanes (VPlane), for helicopters (VBar), for multi-rotors (VCopter), and VBar and VCopter of course with the tried and tested Rescue feature—all required sensors are already on board

Specifications:

• Dimensions     45,5 x 25,6 x 16 mm / 1,79 x 1,01 x 0,63 in
• Weight     14 g
• Supply Voltage     3,5 - 8,4 V (2S Lipo)
• Content
• USB cable     Mini USB Cable, Boot Plug
• main unit     Multiprotocol Single Line Empfänger (Vlink,UDI, S-Bus, Spektrum, PPM)
• Gyrosensor     Internal multi-axis sensor array (inactive in VBasic, enabled by software updates with cost)
• Manual     Printed manual (Quick-Start-Guide, full manual available online on www.vstabi.info)
• Software     VBasic Receiver Firmware, VExtender

• automatic activation and deactivation, depending on the operational status of the model (motor switch position, stick inputs)
• all voltages can be monitored separately via telemetry
• charging currents are adjustable, both for initial charging and for topping-up during operation
• recharges automatically and immediately whenever needed
• companion App warns the pilot whenever the backup is used
• this unit ensures the everyday operation of your valuable models

Hardware features

• wide input voltage range from 3 V up to 12.6 V (3s LiPo) with a 16 V peak margin
• Capacity 3 x 25 F, 20+ A peak current
• short circuit protection
• fast charge (adjustable) up to 2.4 A
• charging current is ramped up slowly, to protect main power supply
• decoupled channels for power delivery and for charging
• VLink Telemetry monitoring and control
• no r/c channel (servo connector) must be sacrificed, pass-through via main connector
• active balancer between capacitors for low idle discharge
• up to 3 units can be connected parallel, tripling the capacity and power; cascaded units are fully suported by companion App
• telemetry input for other sensors or ESCs (daisy-chaining)

Benefits at a glance

automatic activation and deactivation, depending on the operational status of the model (motor switch position, stick inputs)

all voltages can be monitored separately via telemetry

charging currents are adjustable, both for initial charging and for topping-up during operation

recharges automatically and immediately whenever needed

companion App warns the pilot whenever the backup is used

this unit ensures the everyday operation of your valuable models

Hardware features

wide input voltage range from 3 V up to 12.6 V (3s LiPo) with a 16 V peak margin

40+ A peak current

short circuit protection

fast charge (adjustable) up to 2.4 A

charging current is ramped up slowly, to protect main power supply

decoupled channels for power delivery and for charging

VLink Telemetry monitoring and control

no r/c channel (servo connector) must be sacrificed, pass-through via main connector

active balancer between capacitors for low idle discharge

up to 3 units can be connected parallel, tripling the capacity and power; cascaded units are fully suported by companion App

telemetry input for other sensors or ESCs (daisy-chaining)

Specifications
Power Supply 3-12.6 V (3s LiPo), max. 16 V
Dimensions approx. 48 x 55 x 19 mm (H x W x D)
Weight approx. 52 g including wires
Power Rating 40+ A peak
Contents
Device VBar Control Power Backup w/ power wire, manual
Connecting Wire Telemetry wire included
Miscellaneous
Miscellaneous Update VBar NEO, install companion App on transmitter

VBar RX-Only, 7 channel receiver.
Not upgrade-able (can not be updated to Pro/Pro+Rescue, can not be used with gyro sensors).

VBar RX-Only, 9 channel receiver.
Not upgrade-able (can not be updated to Pro/Pro+Rescue, can not be used with gyro sensors).

Mikado Vbar Softtouch rubber to cover for VControl switches

This is the Mikado VBar Control RX-Satellite.

Includes:

VBar control RX-Satellite

Cable to connect RX to Vbar Silverline/Blueline

Li-Io transmitter battery 1s4p 14.000 mAh

with mounting kit for VBar Control EVO

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models via the familiar VBar setup wizard.
• ESC setup wizard for programming all types of speed controllers.
• ESCs with VBar Control support can be programmed directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functions under development (e.g. for archiving, interaction with other users; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).

Hardware Highlights:

• Extra bright capacities 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in three seconds.
• High performance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector or built-in charger.
• Power supply for fast charging included.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models via the familiar VBar setup wizard.
• ESC setup wizard for programming all types of speed controllers.
• ESCs with VBar Control support can be programmed directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functions under development (e.g. for archiving, interaction with other users; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).

Hardware Highlights:

• Extra bright capacities 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in three seconds.
• High performance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector or built-in charger.
• Power supply for fast charging included.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models via the familiar VBar setup wizard.
• ESC setup wizard for programming all types of speed controllers.
• ESCs with VBar Control support can be programmed directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functions under development (e.g. for archiving, interaction with other users; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).

Hardware Highlights:

• Extra bright capacities 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in three seconds.
• High performance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector or built-in charger.
• Power supply for fast charging included.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models via the familiar VBar setup wizard.
• ESC setup wizard for programming all types of speed controllers.
• ESCs with VBar Control support can be programmed directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functions under development (e.g. for archiving, interaction with other users; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).

Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in three seconds.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector or built-in charger.
• Power supply for fast charging included.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Software Highlights:

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models via the familiar VBar setup wizard.
• ESC setup wizard for programming all types of speed controllers.
• ESCs with VBar Control support can be programmed directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functions under development (e.g. for archiving, interaction with other users; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).

Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in three seconds.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector or built-in charger.
• Power supply for fast charging included.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Included in set: Mikado VBar NEO VLink 6.1 Express

• Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio.
• Readily understandable graphic user interface.
• Easy programming for new models via the familiar VBar setup wizard.
• ESC setup wizard for programming all types of speed controllers.
• ESCs with VBar Control support can be programmed directly from the radio.
• Up to eight parameters can be tuned simultaneously using the optional inputs, with adjustable limitation of the the respective range of values.
• Bank switching with three banks (fourth Bank Autorotation optional).
• Real time logging and real time graphic vibration analysis available on display.
• Graphical telemetry log analyzer for stored flights (overview, energy consumption, event-log) directly readable on the display.
• Create your own screendesign directly on the touchscreen display.
• Full manual available on the radio by means of context sensitive help.
• Easy bind process, allows bind and fly of any model equipped with VLink (e.g. a buddy‘s heli) with your own transmitter (Model Sharing).
• Automatic power-on, if an already bound model is switched on.
• Several telemetry functions are available, such as voltages, current, rpm, speed, temperature and power consumption of the batteries (may need additional hardware).
• Multiple timer functions available with warnings and reminders via sound, voice, or vibration output.
• Wireless buddy boxing with two VBar Control radios, fully configurable.
• Cloud functions under development (e.g. for archiving, interaction with other users; usage optional).
• Access our App Store and do over-the-air online-updates via WiFi*.
• Over-the-air online-update your VBar NEO-flybarless systems via WiFi* (for purchases, a device with internet access and web browser is required).

Hardware Highlights:

• Extra bright capacitive 5.8 inch multi-touch color display, with ambient-light sensor to automatically control the brightness.
• Very good readability even in bright sunlight.
• WiFi module connects to your WiFi network at home as well as to your personal hotspot on the go.
• Very fast start-up time, from off to fully operational in three seconds.
• High perfomance low power controller for best user experience and long runtimes.
• Reliable 80 Channel 2.4 GHz FHSS bidirectional flight control, programming/setup and telemetry remote control system.
• Unlimited model memory.
• Virtually unlimited number of control channels.
• High range, low latency, antenna diversity both on transmitter and receiver.
• Intelligent antenna monitoring and management.
• Fully equipped with four 3-position switches, two 3-position quick-break-switches as well as six rotary inputs (four trim wheels, two rotating knobs), all fully programmable.
• Precision gimbals with four ball bearings, fully adjustable.
• Collective stick can be equipped with optional throw limiter.
• Delicate rubber lining for comfortable, slip-free and safe holding.
• Well-balanced with two-point neck-strap attachment, no additional retainer bracked required.
• Large 2 Watt loudspeaker for alarms and voice output.
• Vibration alarm (adjustable).
• Memory accessible as a USB memory stick, no drivers needed.
• Built-in Lithium Polymer battery allows for long run times.
• Charge through USB connector or built-in charger.
• Power supply for fast charging included.

* Online features require a WiFi connection and a device with internet access. Data transfers may cause additional costs, depending on your mobile data plan.

Li-Io transmitter battery 1s2p 7.000 mAh, with mounting kit for VBar Control Touch

THIS battery also can be used on Vbar Classic instead of 05253

Li-Io transmitter battery 1s4p 14.000 mAh

with mounting kit for VBar Control Touch

Mikado Velcro straps 20x280mm (4 pcs)

Mikado Vertical fin, LOGO 700

Mikado Washer for Thrust Bearing, set of 2 #00841

Mikado Wire set "antistatic" For Mikado Logos 500-600

The LOGO 600 combines the proven concept of the LOGO 600 SX with new components and our new signature canopy design:

• 600-620 mm main blades
• for 10S Lipo 5,000 mAh or 12S LiPo up to 3.500 mAh
• light und durable chassis fiberglass reinforced frame with battery quick release system
• direct servo link to the swashplate
• hollow main shaft with 10 mm diameter
• herringbone main gear with 106 teeth (module 1)
• motor counterbearing with additional main shaft support
• xtra-strong 25 mm diameter tail boom

Now with:

• aluminum rotor head with 8 mm spindle shaft and extra-large thrust bearings (ø 16 mm)
• larger swash plate
• aluminum pulley in the chassis
• stronger one-way bearing
• fin set with colored accents in neon red
• newly designed signature airbrush canopy

Specifications:

• Rotor diameter:    1,350 mm-1,450 mm
• Rotor blades: 600/620 mm
• RTF weight:  from ca. 3.4 kg
• recommended batterie:  10S-12S LiPo
• Main gear ratio:  7.1-10.6
• Main Gear size:  106 teeth module 1
• batterie slot:  62 x 54 x 300 mm (HxWxL)
• Length:  1,250 mm
• Hight: 360 mm
• Width: 210 mm

Content:

• Kit: Kit with aluminum rotor head
• Accessories: Anti Static Kit, Motor counterbearing with mainshaft support
• Manual: Detailed printed manual
• Blades: Carbon tail rotor blades, no main blades
• Canopy: Airbrushed Canopy

Mixing arm lever with slide bearing

Mixing arm without ball bearing

Motor counterbearing for 5mm shafts with mainshaft support.

Please use only in combination with plastic mainframe and mainshaft MIK-4620.