YGE

YGE 205 HVT ESC Version 2 - Superb governor, outstanding BEC and FULL Vbar integration! Black Edition

Own YGE protocol for further telemetry connections via e.g. S32 (new jlog of R² prototyping). Further protocols are in preparation.

Due to the optional USB adapter, the 200HVT can be varied and new updates can be added. During operation, the PWM frequency is always automatically adjusted to the needs of the engine and is thus always optimal. Due to the new sine start-up of the 200HVT, the startup behavior is now also SUPERSANFT.

Description:

• The specified current is the maximum continuous full gas flow with good cooling.
• 4 to 14S LiPo, undervoltage reset or shutdown.
• BEC - undervoltage detection can be switched off.
• current limit
• Undervoltage detection can be switched off
• Speed ​​control (governor mode).
• Soft start.
• Active freewheel, thus unlimited part-load.
• Automatic timing, or adjustable in 6 levels.
• EMK brake adjustable.
• F3A / Acro brake (brake intensity steplessly adjustable in flight).
• Min and Max values ​​are logged and can be displayed in the optional PC tool after the flight (for example, power)
• Speed ​​limit: 240,000 rpm (2-pole)
• Overtemperature / overload warning
• Anti-glare: reduces the start-up spark.
• Basic programming via mode setup.

Fine adjustment and choice of telemetry protocol via PC setup, suitable USB adapter is optionally available.

Technical data:

• Manufacturer / Importer     YGE
• Number of cells LiPo     4 - 12
• Number of cells LiFe     5 - 14
• Max. permanent current [A]     205
• Opto coupler     ja
• Brake     ja, abschaltbar
• RPM limit     240.000 rpm (2-Poler)
• Heli mode (gov mode)     ja
• Anti spark     ja
• Programmable     ja
• Dimensions approx. [mm]     89 x 52 x 28
• Weight [g]     189

YGE 205 HVT ESC Version 2 - Superb governor, outstanding BEC and FULL Vbar integration! Black Edition

New Features:

• - improved case-design with optimized cooling
• - 1,5mm narrower
• - The mounting holes are now compatible to common helicopters (distance between holes 43mm)
• - dimensions: 84 x 54,5 x 33mm
• - weight with cables: 287g

"T" for Telemetry

Supported telemetry-protocols:

• - Graupner HoTT V4
• - Jeti ExBUS
• - Multiplex Sensor BUS V2
• - MSH Brain 2
• - Spirit FBL
• - Mikado Vbar Control
• - YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky)

All usual information as current, voltage, capacity, RPM, temperature etc. will be transferred to your transmitter. The amount of data and the characterization depends on your transmitter/receiver.

Technical specifications:

• BEC 5.0V – 8.4V
• BEC 12A continuous, 30A Peak
• “T” for Telemetry. following protocols are currently compatible: Mikado VBC, Graupner HoTT V4, Jeti ExBUS, Multiplex Sensor BUS V2, YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky, Core), MSH Brain 2 or Spirit FBL
• Update capable (optional USB-Adapter available)
• entirely overhauled hard- and software (32-bit)
• the PWM-frequency will be set automatically to the requirements of the motor
• The specified current is the maximum continuous full power current
• 6 to 14s LiPo, incl under voltage protection by power reduction
• Current limiting
• Disconnectable under voltage detection
• Electronic speed control (Governor- mode)
• Soft start
• super soft startup for scale-helicopters possible (60 sec.)
• Active free-wheel, allowing unlimited part load operation
• Automatic or 6 step adjustable timing
• Adjustable EMK brake
• F3A(Acro brake (brake force control infinitely adjustable)
• Frequency: 16 to 32 kHz
• Speed limit: 240.000 rpm (2- Poles)
• Temperature and overload warning
• Anti- flash: decreases the closing spark
• Basic -Programming with mode programming
• Fine adjustment and selection of telemetry log with the PC Setup
• Suitable USB-adapter optionally available
• dimensions (mm): 84 x 54,5 x 33mm
• weight without/with cables: 219g/287g

YGE 205HVT ESC Cable Set. This is a replacement cable set for the 205HVT. Package includes two BEC cables, one throttle cable, and one telemetry cable.

YGE 255 OPTO High voltage Brushless Speed controller 255A continuous / 400A peak 16S,

• integrated antispark

Technical data:

- Continuous current 255A (Full throttle, good cooling conditions). Max. peak current 400A.
- Adjustable current limit up to 400A. The ESC won’t shut down, it will limit the current to 400A.
- 6 to 16s LiPo, max. terminal voltage 68V, nominal operating voltage 63V.
- over 14S all-insulated and touch-proof connectors must be used.
- pluggable receiver- and telemetry cables
- All signals are isolated by opto couplers for best noise immunity.
- Electronic speed control (Governor- mode)
- Soft start
- Active free-wheel, allowing unlimited part load operation.
- Automatic or 6 step adjustable timing
- Frequency: Automatic.
- Adjustable EMK brake
- F3A(Acro brake (brake force control infinitely adjustable)
- Speed limit: 240.000 rpm (2- Poles)
- Temperature and overload warning
- Anti- flash: decreases the closing spark.
- Basic -Programming with mode programming
- Fine adjustment and selection of telemetry with the PC Setup. Suitable USB-adapter optionally available
- Dimensions in mm: 105 x 54 x 32
- Weight with all cables: 343g
- Cable diameter battery / motor: 8² / 8²

Young Generation Electronics, Regler with Telemetry, 2-6 Lipo, 65A permanent, BEC 8A / 5,5 - 9V, Modus-setup, (Governor-Mode)

"T" for Telemetry

Supported telemetry-protocols:

- Graupner HoTT V4
- Jeti ExBUS
- Multiplex Sensor BUS V2
- Mikado Vbar Control
- MSH Brain 2
- Spirit FBL
- YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky)

All usual information as current, voltage, capacity, RPM, temperature etc. will be transferred to your transmitter. The amount of data and the characteristic depends on your transmitter/receiver.

Technical Specifications:

- Update capable (optional USB-Adapter available)

- entirely overhauled hard- und software (32-bit)

- the PWM- frequency will be set automatically to the requirements of the motor

- Current-limitation

- 2 to 6S LiPo

- super smooth sinus-startup

- adjustable HV-BEC from 5,5 to 9V

- high BEC -current rating: 8A permanent / 18A peak

- dimensions in mm: 64x26x9

- weight with / without cables: 30-45g

- basic settings via mode-setup

- BEC- and Telemetry-settings, as well as additional parameters adjustable via PC-Software (optional USB-adapter available)

Young Generation Electronics, Regler with Telemetry, 2-6 Lipo, 95A permanent, BEC 8A / 5,5 - 9V, Modus-setup, (Governor-Mode)

"T" for Telemetry

Supported telemetry-protocols:

- Graupner HoTT V4
- Jeti ExBUS
- Multiplex Sensor BUS V2
- Mikado Vbar Control
- MSH Brain 2
- Spirit FBL
- YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky)

All usual information as current, voltage, capacity, RPM, temperature etc. will be transferred to your transmitter. The amount of data and the characteristic depends on your transmitter/receiver.

Technical Specifications:

- Update capable (optional USB-Adapter available)

- entirely overhauled hard- und software (32-bit)

- the PWM- frequency will be set automatically to the requirements of the motor

- Current-limitation

- 2 to 6S LiPo

- super smooth sinus-startup

- adjustable HV-BEC from 5,5 to 9V

- high BEC -current rating: 8A permanent / 18A peak

- dimensions in mm: 78 x 32 x 15

- weight with / without cables: 78g / 93g

- basic settings via mode-setup

- BEC- and Telemetry-settings, as well as additional parameters adjustable via PC-Software (optional USB-adapter available)

Young Generation Electronics, ESC with Telemetry, 6-12 Lipo, 105A permanent, BEC 12A / 5,0 - 8,4V, Modus-setup, (Governor-Mode)

A new smaller HV-ESC, the Aureus 105.
It is suitable for 550-600 size helicopters with 12s Lipo, and planes with 10-12s setups. The Aureus 105 has full telemetry compatibility with almost all systems on the market, an adjustable high power BEC and our popular current-limiter, whereby the ESC won’t shutdown, it just limits the current.

Supported telemetry-protocols:

- Graupner HoTT V4
- Jeti ExBUS
- Multiplex Sensor BUS V2
- Mikado Vbar Control
- YGE-Protocol for more telemetry-connections for exapmple via S32 (new Jlog)

All usual informations as current, voltage, capacity, RPM, temperature etc. will be transferred to your transmitter. The amount of data and the characterisation depends on your transmitter/receiver.

6 to 12s LiPo, incl under voltage protection by power reduction
BEC 5,0V – 8,4V
BEC 10A continuous, 25A Peak
“T” for Telemetry. following protocols are currently compatible: Mikado VBC, Graupner HoTT V4, Jeti ExBUS, Multiplex Sensor BUS V2, YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky, Core), MSH Brain 2 or Spirit FBL

Update capable (optional USB-Adapter available)

entirely overhauled hard- and software (32-bit)
the PWM-frequency will be set automatically to the requirements of the motor
The specified current is the maximum continuous full power current
Current limiting
Disconnectable under voltage detection
Electronic speed control (Governor- mode)
Soft start
super soft startup for scale-helicopters possible (60 sec.)
Active free-wheel, allowing unlimited part load operation
Automatic or 6 step adjustable timing
Adjustable EMK brake
F3A(Acro brake (brake force control infinitely adjustable)
Frequency: 16 to 32 kHz
Speed limit: 240.000 rpm (2- Poles)
Temperature and overload warning
Anti- flash: decreases the closing spark
Basic -Programming with mode programming
Fine adjustment and selection of telemetry log with the PC Setup
Suitable USB-adapter optionally available
dimensions (mm): 08,5×34,5×19,5
weight without/with cables: 80g/124g:
Content:
- YGE Aureus 105
- RC-Connection Cable
- Fan
- Sticker
- Manual

YGE Aureus 135 Brushless ESC 135A 6-12S with Telemetry and BEC

Properties:

 "T" for Telemetry. following protocols are currently compatible: Mikado VBC, Graupner HoTT V4, Jeti ExBUS, Multiplex Sensor BUS V2, YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky), MSH Brain 2 or Spirit FBL

• Update capable (optional USB-Adapter available)
• entirely overhauled hard- and software (32-bit)
• the PWM-frequency will be set automatically to the requirements of the motor
• The specified current is the maximum continuous full power current
• 6 to 12s LiPo, incl under voltage protection by power reduction
• Current limiting
• Disconnectable under voltage detection
• Electronic speed control (Governor- mode)
• Soft start
• super soft startup for scale-helicopters possible (60 sec.)
• Active free-wheel, allowing unlimited part load operation
• Automatic or 6 step adjustable timing
• Adjustable EMK brake
• F3A(Acro brake (brake force control infinitely adjustable)
• Frequency: 16 to 32 kHz
• Speed limit: 240.000 rpm (2- Poles)
• Temperature and overload warning
• Anti- flash: decreases the closing spark
• Basic -Programming with mode programming
• Fine adjustment and selection of telemetry log with the PC Setup
• Suitable USB-adapter optionally available
• dimensions (mm): 82 x 43,5 x 26
• weight without/with cables: 122g/178g

YGE 135 HVT ESC Black Edition - Superb governor, outstanding BEC and FULL Vbar integration!

• BEC 5,0V - 8,4V
• BEC 10A continuous, 25A Peak
• "T" for Telemetry. following protocols are currently compatible: Mikado VBC, Graupner HoTT V4, Jeti ExBUS, Multiplex Sensor BUS V2, YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky), MSH Brain 2 or Spirit FBL
• Update capable (optional USB-Adapter available)
• entirely overhauled hard- and software (32-bit)
• the PWM-frequency will be set automatically to the requirements of the motor
• The specified current is the maximum continuous full power current
• 6 to 12s LiPo, incl under voltage protection by power reduction
• Current limiting
• Disconnectable under voltage detection
• Electronic speed control (Governor- mode)
• Soft start
• super soft startup for scale-helicopters possible (60 sec.)
• Active free-wheel, allowing unlimited part load operation
• Automatic or 6 step adjustable timing
• Adjustable EMK brake
• F3A(Acro brake (brake force control infinitely adjustable)
• Frequency: 16 to 32 kHz
• Speed limit: 240.000 rpm (2- Poles)
• Temperature and overload warning
• Anti- flash: decreases the closing spark
• Basic -Programming with mode programming
• Fine adjustment and selection of telemetry log with the PC Setup
• Suitable USB-adapter optionally available
• dimensions (mm): 82 x 43,5 x 26
• weight without/with cables: 122g/178g

Young Generation Electronics ESC with Telemetry, 6-12 Lipo, 135A permanent, BEC 10A / 5,5 - 12V, Modus-setup, (Governor-Mode)

Technical Specifications:

BEC 5,5V - 12V

BEC 10A continuous, 25A Peak

"T" for Telemetry. following protocols are currently compatible: Mikado VBC, Graupner HoTT V4, Jeti ExBUS, Multiplex Sensor BUS V2, YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky), MSH Brain 2 or Spirit FBL

Update capable (optional USB-Adapter available)

entirely overhauled hard- and software (32-bit)

the PWM-frequency will be set automatically to the requirements of the motor

The specified current is the maximum continuous full power current

6 to 12s LiPo, incl under voltage protection by power reduction

Current limiting

Disconnectable under voltage detection

Electronic speed control (Governor- mode)

Soft start

super soft startup for scale-helicopters possible (60 sec.)

Active free-wheel, allowing unlimited part load operation

Automatic or 6 step adjustable timing

Adjustable EMK brake

F3A(Acro brake (brake force control infinitely adjustable)

Frequency: 16 to 32 kHz

Speed limit: 240.000 rpm (2- Poles)

Temperature and overload warning

Anti- flash: decreases the closing spark

Basic -Programming with mode programming

Fine adjustment and selection of telemetry log with the PC Setup

Suitable USB-adapter optionally available

dimensions (mm): 82 x 43,5 x 26

weight with cables: 178g

Content:

- YGE Aureus 135 V2

- RC-Connection Cable

- Torodial Core

- Fan

- Sticker

- Manual

Supported telemetry-protocols

Graupner HoTT V4
Jeti ExBUS
Multiplex Sensor BUS V2
Mikado Vbar Control
YGE-Protocol for more telemetry-connections for example via S32 (new Jlog)

Technical Specifications:

4 to 8s LiPo, incl under voltage protection by power reduction
BEC 5,0V – 8,4V
BEC 12A continuous, 25A Peak
“T” for Telemetry. following protocols are currently compatible: Mikado VBC, Graupner HoTT V4, Jeti ExBUS, Multiplex Sensor BUS V2, YGE-protocol for different telemetry-connections for example via YGE TexY (Futaba, Spektrum, FrSky, Core), MSH Brain 2 or Spirit FBL

Update capable (optional USB-Adapter available)

entirely overhauled hard- and software (32-bit)
the PWM-frequency will be set automatically to the requirements of the motor
The specified current is the maximum continuous full power current
Current limiting
Disconnectable under voltage detection
Electronic speed control (Governor- mode)
Soft start
super soft startup for scale-helicopters possible (60 sec.)
Active free-wheel, allowing unlimited part load operation
Automatic or 6 step adjustable timing
Adjustable EMK brake
F3A(Acro brake (brake force control infinitely adjustable)
Frequency: 16 to 32 kHz
Speed limit: 240.000 rpm (2- Poles)
Temperature and overload warning
Anti- flash: decreases the closing spark
Basic -Programming with mode programming
Fine adjustment and selection of telemetry log with the PC Setup
Suitable USB-adapter optionally available
dimensions (mm): 76,5×34,5×19,5
weight without/with cables: 80g/124g:

Content:

- YGE Saphir 125
- RC-Connection Cable
- Fan
- Sticker
- Manual

Supported telemetry-protocols
Graupner HoTT V4
Jeti ExBUS
Multiplex Sensor BUS V2
Mikado Vbar Control
YGE-Protocol for more telemetry-connections for exapmple via S32 (new Jlog)

Technical Specifications:

- Update capable (optional USB-Adapter available)

- entirely overhauled hard- und software (32-bit)

- the PWM-frequency will be set automatically to the requirements of the motor

- Current-limitation

- 2 to 6S LiPo

- super smooth sinus-startup

- adjustable HV-BEC from 5,5 to 8,4V

- high BEC-current rating: 10A permanent / 22A peak

- dimensions in mm: 82 x 39 x 23

- weight with / without cables: 104g / 132g

- basic settings via mode-setup

- BEC- and Telemetry-settings, as well as additional parameters adjustable via PC-Software (optional USB-adapter available)

The smart adapter cable TexY scales up the telemetry of our new generation of speed controllers (T-series) by four more manufacturer protocols:

Futaba SBUS2,

FrSky S.Port,

Spektrum XBUS,

Powerbox Core

The startup is Plug’nPlay with Autodetect !

Weight: approx. 3g

Dimensions: 39 x 12 x 9mm

USB-interface for programming and updating all LVT- and HVT- speed controllers

YGE Vbar-Adapter for using the LVT/HVT-controller with Vbar-telemetry

RPM-Output connection for using the vbar-governor

Length about 10cm/60cm

Additional long one-piece telemetry cable for use with all Aureus, Saphir and 205HVT ESCs