Vision behind Vector multicopters, Just A Minute to retract it from the Peli case, and you ready to takeoff,
Delivered with Peli case.
Vector Vision design is a unique combination of winning features. Compact and rigid body is simple and has only few parts. Simplicity means reliability and easy maintenance.
Vector Vision body has two parts. Upper frame and lower frame. Upper frame has only four different parts excluding nuts and bolts. It is the simplest possible solution to hold motors and motor speed controllers. Lower frame is connected to upper frame with dampeners. Lower frame serves platform for retractable landing gear, flight packs, video link, data link and gimbal quick release system. Significant mass is concentrated on lower frame isolating it from potential vibrations from upper frame. Dampers can also be adjusted to softer or harder type if needed to allow fine tuning.
Autopilot is placed in exact center of the frame. It has two trays that attach to the top center plate. Vector Vision can be equipped with Zero UAV X4 autopilot versions. Our recommendation is to use the new X4 P pilot with best IMU and 50 way points. This is usually enough for even demanding missions. In autopilot platform IMU is also positioned so that sensors are in same plane as the propellers. Compass and GPS have their own place on top deck, again in the center of the aircraft. All wires are carefully hidden in the autopilot deck compound.
Operator needs around one minute to open carrying case and unfold Vector Vision and connect power. After autopilot system check its ready to take off. There is no other system available in the market today that comes anywhere near this.
Gimbals or other instruments can be connected to Vector Vision platform with quick release system. The Quick release plate is designed to hold up to 2,5kg of instrument weight. It has also a special bus for connecting all gimbal electronics to flight control system. Quick release connector plate is separately available to mount your own instruments. Vector Crane gimbals have the right connection as standard.
Vector Vision has a manual retractable landing gear as standard. Landing gear is designed so that it can easily be upgraded with motor driven gear system. This can be done by replacing the centerpiece with integrated gear motor. Retracts can also be ordered as an option
VECTOR VISION 6
Vector multicopters have been designed to meet RPAS regulations
Maximum flying weight 3,8 kg
Configuration - hexacopter
Diameter from motor to motor 600 mm
Prop size 11"
Max battery 2 X 3S 5000 mAh (2 x 55Wh)
Operating voltage 22,2V
Standard Flight Controller Zero UAV X4 wifi
Quick release connection for instrument platform mechanical and electronics
Retractable landing gear is option (will use extra 120 g of payload)
Vector Vision body has two parts. Upper frame and lower frame. Upper frame has only four different parts excluding nuts and bolts. It is the simplest possible solution to hold motors and motor speed controllers. Lower frame is connected to upper frame with dampeners. Lower frame serves platform for retractable landing gear, flight packs, video link, data link and gimbal quick release system. Significant mass is concentrated on lower frame isolating it from potential vibrations from upper frame. Dampers can also be adjusted to softer or harder type if needed to allow fine tuning.
Autopilot is placed in exact center of the frame. It has two trays that attach to the top center plate. Vector Vision can be equipped with Zero UAV X4 or Wookong autopilot versions. Our recommendation is to use the new X4 P pilot with best IMU and 50 waypoints. This is usually enough for even demanding missions. In autopilot platform IMU is also positioned so that sensors are in same plane as the propellers. Compass and GPS have their own place on top deck, again in the center of the aircraft. All wires are carefully hidden in the autopilot deck compound.
Operator needs around one minute to open carrying case and unfold Vector Vision and connect power. After autopilot system check its ready to take off. There is no other system available in the market today that comes anywhere near this.
Gimbals or other instruments can be connected to Vector Vision platform with quick release system. The Quick release plate is designed to hold up to 2,5kg of instrument weight. It has also a special bus for connecting all gimbal electronics to flight control system. Quick release connector plate is separately available to mount your own instruments. Vector Crane gimbals have the right connection as standard.
Vector Vision has a manual retractable landing gear as standard. Landing gear is designed so that it can easily be upgraded with motor driven gear system. This can be done by replacing the centerpiece with integrated gear motor. Retracts can also be ordered as an option
VECTOR VISION 7
Vector multicopters have been designed to meet RPAS regulations
Maximum flying weight 5 kg
Configuration - hexacopter, Assembled, Tested
Diameter from motor to motor 720 mm
Prop size 13"
Max battery 2 X 3S 6600 mAh (2 x 74Wh)
Operating voltage 22,2V
Standardf Flight Controller Zero UAV X4 wifi
Quick release connection for instrument platform mechanical and electronics
Retractable landing gear is option (will use extra120 g of payload)
Included:
Frame: Configuration - hexacopter
Motors: Tiger MN3508
ESC: TIGER PRO 30A
PROPS: TIGER CARBON 13"
Flight controller: Wookong
Delivery time: 1-2 Weeks, Gimbal & Camera not included!
Recommended equipment to complete:(can be delivered as option)