Upgrades Blade Helis

Upgrades Blade Helis

Aftermarket upgrades and tuning for Blade helicopters

Products


  • Fusuno CF Landing Gear Blade 180 CFX Goblin style (Neon Orange)

    Fusuno CF Landing Gear Blade 180 CFX Goblin style (Neon Orange)

    Fusuno CF Landing Gear Blade 180 CFX Goblin style (Neon Orange)

    Specification:

    • 2 x FUP-B180-LG02-CFOR CF Landing Gear Blade 180 CFX (Neon Orange decal)
    • 1 x FUP-180ALS01 Aluminum Landing Skid mount (rear)
    • 1 x FUP-180ALS02 Aluminum Landing Skid mount (front)
    • 4 x PHS-1604 Pan head screw M1.6x4
    SKU: FUP-B180-LG04
    €17.90
    inc. VAT

     LOW STOCK
  • Fusuno CF Tail Fin Blade 180 CFX (Neon Orange)

    Fusuno CF Tail Fin Blade 180 CFX (Neon Orange)

    Fusuno CF Tail Fin Blade 180 CFX (Neon Orange)

    Specification:

    • 1 x FUP-B180-VFN01-CFOR Fusuno CF Tail Fin Blade 180 CFX (Neon Orange)
    • 1 x FUP-180-FPS Aluminum Vertical Fin Pin 2.5mm (Blade 180 CFX)
    • 1 x PHS-1403 Pan head screw M1.4x3
    SKU: FUP-B180-VFN01-CFOR
    €4.90
    inc. VAT

     LOW STOCK
  • FUSUNO Green Energy Blade 180 CFX Speed Fuselage Combo

    FUSUNO Green Energy Blade 180 CFX Speed Fuselage Combo

    FUSUNO Green Energy Blade 180 CFX Speed Fuselage Combo

    Includes:

    • Green Energy Blade 180 CFX Speed Fuselage (TDR shape)   
    • Fusuno CF Landing Gear Blade 180 CFX - TDR style (Low profile)       
    • Fusuno CF Tail Fin Blade 180 CFX   
    • Zeal Carbon fiber Energy main blades 155mm (Green) for Blade 180CFX and Stretched Blade 130X   
    • Fusuno Extreme Stiff XS Engineering Plastic Tail Blade 34mm - 180 CFX (Neon Green)   

    FUSELAGE INSTALLATION GUIDE:

    Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
    Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
    Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
    Remove two button head screws on both sides of the frame.
    Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
    Secure the Fusuno tail boom by tighten up the two button head screws.
    Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
    Re-install the tail gear box and secure using the Fusuno CF vertical fin.

     

    SKU: FUCB-B180-SF05
    €79.50
    inc. VAT

     IN STOCK
  • FUSUNO Monster Airbrush fiberglass Blade 180 CFX Goblin Fuselage

    FUSUNO Monster Airbrush fiberglass Blade 180 CFX Goblin Fuselage

    FUSUNO Monster Airbrush fiberglass Blade 180 CFX Goblin Fuselage

    PRODUCT INCLUDES:

    • 1 x Airbrush fiberglass canopy
    • 1 x Airbrush fiberglass tail boom
    • 1 x CF vertical Fin

    DESCRIPTION:

    • Use for Blade 180 CFX.
    • Easy to install!
    • Separated body, it’s very easy to replace battery!
    • Weight approximate: 25g (Canopy + Boom).

    INSTALLATION GUIDE

    • Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
    • Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
    • Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
    • Remove two button head screws on both sides of the frame.
    • Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
    • Secure the Fusuno tail boom by tighten up the two button head screws.
    • Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
    • Re-install the tail gear box and secure using the Fusuno CF vertical fin.
    SKU: FUC-B180-SF01
    €39.90
    inc. VAT

     LOW STOCK
  • FUSUNO Uruka Airbrush fiberglass Blade 180 CFX Goblin Fuselage

    FUSUNO Uruka Airbrush fiberglass Blade 180 CFX Goblin Fuselage

    FUSUNO Uruka Airbrush fiberglass Blade 180 CFX Goblin Fuselage

    PRODUCT INCLUDES:

    • 1 x Airbrush fiberglass canopy
    • 1 x Airbrush fiberglass tail boom
    • 1 x CF vertical Fin

    DESCRIPTION:

    • Use for Blade 180 CFX.
    • Easy to install!
    • Separated body, it’s very easy to replace battery!
    • Weight approximate: 25g (Canopy + Boom).

    INSTALLATION GUIDE

    • Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
    • Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
    • Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
    • Remove two button head screws on both sides of the frame.
    • Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
    • Secure the Fusuno tail boom by tighten up the two button head screws.
    • Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
    • Re-install the tail gear box and secure using the Fusuno CF vertical fin.

     

    SKU: FUC-B180-SF03
    €39.90
    inc. VAT

     LOW STOCK
  • Head Rubber O-Ring Set - Blade 200SRX

    Head Rubber O-Ring Set - Blade 200SRX

    Rubber O-Rings support to reduce plays at link Blade Grips and Swash plate with Linkage Rod.

    Usage: Blade 200SRX.

    Included: Head Rubber O-Ring (1set).4p

    SKU: RKH-200SRX-OR
    €2.84
    inc. VAT

     IN STOCK
  • Lightweight Carbon Fiber Blade 180CFX Main Frame Panel (2PCs) from Lynx

    Lightweight Carbon Fiber Blade 180CFX Main Frame Panel (2PCs) from Lynx

    The 180CFX Lightweight Main Frame not only delivers incredibly precise and crisp response but also increased frame opening for extra electronics or easy maintenance.

    FEATURES:

    • Fully compatibility with 180CFX standard Heli
    • Lightweight design.
    • Easy assembly and maintenance.

    TECHNICAL SPECIFICATION:

    • Carbon Fiber Material: 3K Carbon Fiber – 1.0 mm Thickness
    • Weight : 7.5g full set (2 pc)

    PACKING LIST:

    • 2 x 180CFX - Lightweight CF Main Frame
    SKU: LX1413
    €11.50
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX - Tail Boom STD Length - Black (2PC)

    Lynx - Blade 180CFX - Tail Boom STD Length - Black (2PC)

    Lynx - Blade 180CFX - Tail Boom STD Length - Black (2PC)

    Lynx Heli Innovations 180CFX Aluminum Ultra Tail Boom is now available and ready for action!
    Available in standard and stretch length, black and red anodize finish.
    We designed and produced this new high quality Aluminum tail boom to be ultra-strong and stiff with the outer dimension as the standard boom for perfect fitment without modification.
    We use high quality OEM Lynx Aluminum extruded material to assure precise tolerances and top material quality specification,

    FEATURES:

    • Direct replacement for your standard length 180CFX tail boom.
    • Available in standard and stretch length and two anodize color finish.

    TECHNICAL SPECIFICATION:

    • Tail Boom Material: Aluminum 6061-T6 – Anodize Finish

    PACKING LIST:

    • 2 x Standard Length 180CFX Ultra Tail Boom - Black
    SKU: LX1415
    €11.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX CNC Aluminum Antirotation Guide Red

    Lynx - Blade 180CFX CNC Aluminum Antirotation Guide Red

    Lynx - Blade 180CFX CNC Aluminum Antirotation Guide Red

    Lynx Heli Innovations is always looking for a better way of doing things.
    Lynx redesign the standard plastic 180CFX anti-rotation bracket using aluminum alloy and special features to increase the overall performance.
    Small details make an important difference; FEA analysis software give us the support to determinate the best compromise between weight and stiffener, in order to assure the best fly performance without add any unnecessary weight.

    FEATURES:

    • Enlarged base surface to fit in the frame and avoid rotation in fly.
    • Super Precise Autorotation Pin slot cut for the smooth sliding
    • Enlarged Autorotation Pin contact surface for the best guide
    • Hex Cup Screw fastening  for the easy and fast lock
    • Unique and stylish Lynx design
    • Easy and quick installation.

    TECHNICAL SPECIFICATION:

    • Anti-Rotation Bracket Material: Aluminum 6061-T6 – anodized
    • Weight: 0.55g

    PACKING LIST:

    • 1 x 180CFX Aluminum Antirotation Guide Red
    • 1 x Hex Cup Screw M1.6x4
    SKU: LX1381
    €5.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX CNC Main Gear Set Black Hub

    Lynx - Blade 180CFX CNC Main Gear Set Black Hub

    Lynx - Blade 180CFX CNC Main Gear Set Black Hub

    Lynx Heli Innovations redesign a 180CFX Main Gear Hub that supports Lynx CNC Main Gear.
    This option is dedicated to pilot who needs a super precise and reinforced CNC Main gear keeping the lightweight as possible and doesn’t need an autorotation system.
    Smooth power transmission and Heavy Duty specification will support your 180CFX need to next level.
    We spent time optimizing the design and fly testing to achieve the required strength and resistance with final design without compromise.
    We are pilots, and we demand a Heli that can support any over-stress fly condition.

    FEATURES:

    • Direct replacement of standard 180CFX main gear, useable with standard or upgraded main shaft.
    • Techno polymer Precise and reinforced CNC main gear assures best wear resistance and perfect tooth mesh.
    • Super precise Main gear concentricity for smooth and silent power transmission
    • Reinforced Main gear for the ultimate main gear rigidity and special cut design to increase crash impact resistance.
    • FEA (Finite Elements Analysis) assisted, achieve lightweight and maximum strength.

    TECHNICAL SPECIFICATION:

    • Main Gear Hub Material: Aluminum 7075-T6 Anodized
    • Main Gear Material: Techno polymer based POM

    PACKING LIST:

    • 1 x 180CFX CNC Main Gear assembled with Main Gear Hub Black
    SKU: LX1436
    €21.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX CNC Ultra Main Grip Set - Black

    Lynx - Blade 180CFX CNC Ultra Main Grip Set - Black

    Lynx - Blade 180CFX CNC Ultra Main Grip Set - Black

    Lynx Heli Innovations has redesigned the standard 130 X plastic main grip, using aluminum alloy.
    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight.
    We spent hours optimizing the design to achieve the required strength with a final weight beyond compromise. We are pilots, and we demand a light helicopter.
    After many flights and simulation , we decided to “stretch” our main grip 1.5 mm, moving the main blade lock hole position far 1.5mm compare the standard version, this tiny change have amazing  positive effect in the heli performance, because  increase the rotor disc of 3 mm, giving better pops and more cyclic authority.  
    The details and design of these blade grips add top performance of your helicopter.
    Strength, durability, accurate CNC tolerances, finish, and most important weight.
    Almost unbelievable, but this main grip set weighs just 1.8 g heavier than the original plastics grips, with a huge increase in rigidity and strength.
    These main grips increase flight precision, flight after flight.

    FEATURES:

    • These grips are a direct replacement for the standard 180CFX parts.
    • Optimized design to assure strong and weight average.
    • Stretched design, increase 3 mm main rotor disc diameter, better pops and cyclic authority

    TECHNICAL SPECIFICATIONS:

    • Main grip material: Aluminum 7075-T6 – anodized finish
    • Bearing material: SST – ABEC5
    • Hardware:  Steel 12.9 Class - DIN 912
    • Assembly weight: 5.8g

    PACKING LIST:

    • 2 x 180CFX – CNC Main Grips – Black Color - preassembled ready to fly
    • Set of shims for the best fine adjustement assembly
    SKU: LX1440
    €29.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX CNC Ultra Main Grip Set - Red

    Lynx - Blade 180CFX CNC Ultra Main Grip Set - Red

    Lynx - Blade 180CFX CNC Ultra Main Grip Set - Red

    Lynx Heli Innovations has redesigned the standard 130 X plastic main grip, using aluminum alloy.
    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight.
    We spent hours optimizing the design to achieve the required strength with a final weight beyond compromise. We are pilots, and we demand a light helicopter.
    After many flights and simulation , we decided to “stretch” our main grip 1.5 mm, moving the main blade lock hole position far 1.5mm compare the standard version, this tiny change have amazing  positive effect in the heli performance, because  increase the rotor disc of 3 mm, giving better pops and more cyclic authority.  
    The details and design of these blade grips add top performance of your helicopter.
    Strength, durability, accurate CNC tolerances, finish, and most important weight.
    Almost unbelievable, but this main grip set weighs just 1.8 g heavier than the original plastics grips, with a huge increase in rigidity and strength.
    These main grips increase flight precision, flight after flight.

    FEATURES:

    • These grips are a direct replacement for the standard 180CFX parts.
    • Optimized design to assure strong and weight average.
    • Stretched design, increase 3 mm main rotor disc diameter, better pops and cyclic authority

    TECHNICAL SPECIFICATIONS:

    • Main grip material: Aluminum 7075-T6 – anodized finish
    • Bearing material: SST – ABEC5
    • Hardware:  Steel 12.9 Class - DIN 912
    • Assembly weight: 5.8g

    PACKING LIST:

    • 2 x 180CFX – CNC Main Grips – Red Color - preassembled ready to fly
    • Set of shims for the best fine adjustement assembly
    SKU: LX1439
    €29.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX Swashplate Leveler

    Lynx - Blade 180CFX Swashplate Leveler

    Lynx - Blade 180CFX Swashplate Leveler

    Accurate swash plate alignment is required for optimum FBL performance. This alignment can only be assessed with precise tools.
    Lynx Heli Innovations has designed a dedicated swash plate leveler for your 180CFX
    We combine lightweight, exotic materials and stylish design with high tolerance production, resulting in a tool to achieve precise set-up of your helicopter.

    FEATURES:

    • Dedicated design for 180CFX helicopter
    • Precise dimensions and tolerance for the best main shaft fitting
    • Help and support superior heli swashplate set up.
    • FEA (Final Elements Analysis) assisted, achieve lightweight and maximum strength.

    SPECIFICATION:

    • Material: Aluminum Alloy 6061-T6

    PACKING LIST:

    • 1 x 180CFX – Swashplate Leveler
    SKU: LX1406
    €9.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX Tail Grip Red

    Lynx - Blade 180CFX Tail Grip Red

    Lynx - Blade 180CFX Tail Grip Red

    Lynx Heli Innovations has redesigned the standard 180CFX plastic tail grip, using aluminum alloy.
    Our tail grip are weighted with integrated CNC weigh, we choose for this specific application to add the center balancer near the lock screw, were will not affect with the normal tail system.
    We also determinate vibration form a unbalanced tail grip system, and thanks a special software we moved the position of the linkage ball to move the CG closer possible the tail hub centerline.
    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight, in particular micro helicopters tail components, were smaller weight difference  can made huge difference in final performance.
    We spent hours optimizing the design to achieve the required strength with a final weight beyond compromise. We are pilots, we expect form our upgrade a better performance.
    The counter couple weights are sized to reduce the servo load during fly, giving faster tail response, less vibration and increase tail servo longevity.
    The details and design of these tail grips add top performance in your 180CFX tail system.

    FEATURES:

    • Direct replacement for the standard 180CFX tail parts.
    • Increase tail response and reduce vibration.
    • Preassembled with lock thread linkage balls and lubricated bearing
    • SST linkage balls to assure durability and wear resistance
    • Integrated CNC counter balance weight to reduce servo load during fly maneuvers, giving faster tail response, less vibration and increase tail servo longevity.
    • FEA (Final Elements Analysis) design assisted, achieve lightweight and maximum strength.

    SPECIFICATION:

    • Tail Grip material: Aluminum 7075-T6 – clear anodized
    • Bearing Material: SST – ABEC5
    • Linkage Ball Material: SST
    • Assembly weight: 2.5g

    PACKING LIST:

    • 2 x 180CFX Tail Grips Red pre-assembly

     

    SKU: LX1421
    €19.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX Ultra Center Hub Red

    Lynx - Blade 180CFX Ultra Center Hub Red

    LYNX - Blade 180CFX Ultra Center Hub Red

    Lynx Heli Innovations has redesigned the standard 180 CFX plastic Head Center Hub, using aluminum alloy.
    This part will add fly precision and shock resistance to your 180 CFX.
    Helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight.
    We spent time optimizing the design and fly testing to achieve the required strength with a final weight beyond compromise. We are pilots, and we demand a light helicopter.
    Details and design combined with strength, durability, accurate CNC tolerances, finish, and most important lightweight, will increase and assure flight precision, flight after flight, adding top performance in your 180 CFX.
    Lynx upgrade design: the new frontier of lightweight and high precision upgrade parts for your helicopters.

    FEATURES:

    • Precision and higher tensile stretch increase fly precision and parts durability.
    • Direct replacement for the standard 180 CFX part.
    • FEA (Final Elements Analysis) assisted, achieve lightweight and maximum strength.

    TECHNICAL SPECIFICATION:

    • Material: Aluminum 7075-T6 – anodized finish
    • Hardware Material: Carbon Steel

    PACKING LIST:

    • 1 x 180CFX Ultra Center Hub Red
    • 1 x Hex Cup Screw M1.6x8 Hex socket 1.5
    SKU: LX1371
    €18.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX Ultra Swashplate Black

    Lynx - Blade 180CFX Ultra Swashplate Black

    Lynx - Blade 180CFX Ultra Swashplate Black

    Lynx Heli Innovations has redesigned and improved the standard 180CFX Swash plate using a combination of 7075 aluminum alloy, chrome steel and copolymer parts.
    We work tirelessly to optimize our designs and perform flight-testing to achieve the desired benefits with a final weight and design specification without compromise.  We are pilots, and we demand upgrades that truly deliver increased performance with the lightest weight possible.
    Lynx Heli Innovations is proud to introduce our own in house design Spherical Swivel Bearing assembly that allows the swash plate to pivot around the main shaft better than ever!  Thanks to our experience and our desire to for better solutions, we have created a new Spherical Bearing bushing from a low friction copolymer to ensure an incredibly smooth, solid and precise swivel action while eliminating looseness between the ball and bushing for drastic elimination of any free play.
    See cross section diagram, here below, to understand better about our fine design construction.
    The Spherical Bearing assembly is now replaceable/serviceable by the customer.  It is composed of a chrome steel center ball and a low friction copolymer bushing surrounding the center ball.  These parts are proudly produced by Lynx and factory assembled to become the heart of the Lynx Ultra SwashPlate.
    For those who push the limits and fly beyond them, this swash plate was designed to be almost completely rebuild-able by the customer.  Offering an economic service parts bag, you will be able to follow the simple instructions and replace the parts most prone to wear, the Spherical Bearing assembly and the linkage balls.  (The large center ball bearing is pre-lubricated and permanently mated to the housings and the center is press fit to ensure a long life.)
    Thanks to our hard work and rigorous design specifications, the Lynx 180CFX Ultra SwashPlate results in an incredibly strong and virtually indestructible part.
    Attention to detail and design combined with material strength, durability, precise CNC tolerances, fit and finish and most important lightweight all contribute to the added precision and the ability for the customer to rebuild, which ensures the best possible performance flight after flight for the 180CFX.
    The Lynx 180CFX Ultra SwashPlate of course looks great, but it also has the benefits and performance increase to match! Lynx Ultra SwashPlates are the next level in lightweight, precision and rebuild-able swash plates.

    FEATURES:

    • Direct fit replacement part for the standard 180CFX SwashPlate.
    • Innovative in house designed and manufactured ultra precise Spherical Bearing for a smooth and solid swivel action.
    • Stainless Steel linkage balls for the best wear and shock resistance.
    • Double High quality ABEC5 Stainless Steel maximum precision and durability.
    • Customer rebuild-able Swash Plate from service parts bag.
    • Factory assembled with thread lock on linkage balls and pre-lubricated bearing.
    • FEA (Final Elements Analysis) used in achieving the most lightweight part with maximum strength.

    TECHNICAL SPECIFICATION:

    • Swash Plate Material: Aluminum 7075-T6 – anodized finish
    • Linkage Ball Material: Stainless Steel
    • Bearing Material: Stainless Steel – ABEC5 precision class
    • Spherical Swivel Bearing Material: Center Ball Chrome Steel HRC40 / Swivel Bushing low-friction copolymer POM based.  
    • Weight: 4 g

    PACKING LIST:

    • 1 x 180CFX Ultra SwashPlate , Black pre-assembled, ready to fly plug and play
    SKU: LX1401
    €29.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX Ultra Swashplate Red

    Lynx - Blade 180CFX Ultra Swashplate Red

    Lynx - Blade 180CFX Ultra Swashplate Red

    Lynx Heli Innovations has redesigned and improved the standard 180CFX Swash plate using a combination of 7075 aluminum alloy, chrome steel and copolymer parts.
    We work tirelessly to optimize our designs and perform flight-testing to achieve the desired benefits with a final weight and design specification without compromise.  We are pilots, and we demand upgrades that truly deliver increased performance with the lightest weight possible.
    Lynx Heli Innovations is proud to introduce our own in house design Spherical Swivel Bearing assembly that allows the swash plate to pivot around the main shaft better than ever!  Thanks to our experience and our desire to for better solutions, we have created a new Spherical Bearing bushing from a low friction copolymer to ensure an incredibly smooth, solid and precise swivel action while eliminating looseness between the ball and bushing for drastic elimination of any free play.
    See cross section diagram, here below, to understand better about our fine design construction.
    The Spherical Bearing assembly is now replaceable/serviceable by the customer.  It is composed of a chrome steel center ball and a low friction copolymer bushing surrounding the center ball.  These parts are proudly produced by Lynx and factory assembled to become the heart of the Lynx Ultra SwashPlate.
    For those who push the limits and fly beyond them, this swash plate was designed to be almost completely rebuild-able by the customer.  Offering an economic service parts bag, you will be able to follow the simple instructions and replace the parts most prone to wear, the Spherical Bearing assembly and the linkage balls.  (The large center ball bearing is pre-lubricated and permanently mated to the housings and the center is press fit to ensure a long life.)
    Thanks to our hard work and rigorous design specifications, the Lynx 180CFX Ultra SwashPlate results in an incredibly strong and virtually indestructible part.
    Attention to detail and design combined with material strength, durability, precise CNC tolerances, fit and finish and most important lightweight all contribute to the added precision and the ability for the customer to rebuild, which ensures the best possible performance flight after flight for the 180CFX.
    The Lynx 180CFX Ultra SwashPlate of course looks great, but it also has the benefits and performance increase to match! Lynx Ultra SwashPlates are the next level in lightweight, precision and rebuild-able swash plates.

    FEATURES:

    • Direct fit replacement part for the standard 180CFX SwashPlate.
    • Innovative in house designed and manufactured ultra precise Spherical Bearing for a smooth and solid swivel action.
    • Stainless Steel linkage balls for the best wear and shock resistance.
    • Double High quality ABEC5 Stainless Steel maximum precision and durability.
    • Customer rebuild-able Swash Plate from service parts bag.
    • Factory assembled with thread lock on linkage balls and pre-lubricated bearing.
    • FEA (Final Elements Analysis) used in achieving the most lightweight part with maximum strength.

    TECHNICAL SPECIFICATION:

    • Swash Plate Material: Aluminum 7075-T6 – anodized finish
    • Linkage Ball Material: Stainless Steel
    • Bearing Material: Stainless Steel – ABEC5 precision class
    • Spherical Swivel Bearing Material: Center Ball Chrome Steel HRC40 / Swivel Bushing low-friction copolymer POM based.  
    • Weight: 4 g

    PACKING LIST:

    • 1 x 180CFX Ultra SwashPlate , Red pre-assembled, ready to fly plug and play
    SKU: LX1400
    €29.90
    inc. VAT

     IN STOCK
  • Lynx - Blade 180CFX Ultra Tail Boom clamp Red

    Lynx - Blade 180CFX Ultra Tail Boom clamp Red

    Lynx Blade 180CFX Ultra Tail Boom clamp Red

    The 180CFX is an amazing RTF helicopter. Lynx has looked closely at the helicopter’s performance, and we have found a number of areas for improvement. One issue we noted was the standard heli Tail Boom Clamp.
    These parts originally in plastic can’t clamp the boom as need, than vibe or tail wag can upend, reducing the tail system performance.
    Lynx Heli Innovations has redesigned the standard 180CFX plastic tail boom clamp, using aluminum alloy.
    We designed a clamp that once installed will lock perfectly the boom making the tail system “rock-solid”. Like any Lynx part we aim for the strongest part with the lightest weight. We always look for upgrades that will not compromise helicopter performance.
    Our design removes the old and not necessary horizontal fin to give a modern and high-tech heli looking.
    The details and design of this tail boom clamp  mount add top performance and an exotic look to your 180CFX tail system.

    FEATURES:

    • Direct replacement for the standard 180CFX tail parts.
    • Optimized tail boom support for a “rock solid” clamp.
    • Increased rigidity of the tail system improving tail performance reducing wag and vibes.
    • FEA (Final Elements Analysis) design assistance, achieving the lightest weight with the maximum strength.

    TECHNICAL SPECIFICATIONS:

    • Tail Boom Clamp Material: Aluminum 7075-T6 – anodized finish.
    • Screw material: Carbon steel 12.9 class
    • Weight: 0.4g

     PACKING LIST:

    • 1 x 180CFX Tail Boom Clamp Red
    • 3 x Hex Cup Screw M1.6X4
    SKU: LX1378
    €7.90
    inc. VAT

     IN STOCK
  • Lynx Double Ball Bearing Tail Pitch Slider Red Devil Blade 130X

    Lynx Double Ball Bearing Tail Pitch Slider Red Devil Blade 130X

    Lynx Double Ball Bearing Tail Pitch Slider Red Devil Blade 130X LX0904

    Lynx Heli Innovations has redesigned and improved upon the standard 130X plastic tail pitch slider, using a combination of 7075 aluminum alloy, low friction brass bushings and more robust linkages that comes fully assembled with spare parts.

    The Pro Edition, as usual for Lynx represents the highest evolution in performance and quality. The tail pitch slider was revised with tighter tolerances and ABEC5 double bearings to give you the best smoothest actuating tail pitch slider for the 130X. In response to customer suggestions Lynx proudly introduces the Pro Edition tail pitch slider linkages. To save you time and headache we have pre-assembled the linkages and pins at the factory. We even include a spare set of linkages and pins to save down time after the eventual crash.

    The tail pitch slider is one of the most critical components in any helicopter tail case. In order to insure the best performance, lightweight, precision and smoothness the bearings and bushings were our primary focus during our redesign.
    After extensive testing, Lynx specified double ABEC5 radial bearings and special low friction brass bushings to slide freely on the tail shaft. No more tail jitters due to slow, sticky tail pitch sliders with loose fitment.

    The tail pitch slider is factory assembled using dedicated equipment and expert staff with attention to detail in order to insure maximum quality and repeatability.

    Details, design, strength, durability, precise CNC tolerances, fit and finish, and most importantly lightweight all contribute to increased tail response and insures precision tail holding ability while minimizing vibration flight after flight. This is the perfect first upgrade that offers a big tail performance boost for every 130X.

    FEATURES:

    • Direct fit replacement part for the standard 130 X tail pitch slider
    • Preassembled with lubricated bearings
    • Includes two spare linkages and pins
    • FEA (Final Elements Analysis) assisted in achieving the most lightweight part with maximum strength.
    Pro Edition Special improved Features:

    • Revised dimensions, tighter tolerances for the best performance and no vibrations
    • Highest quality radial bearings for the smoothest operation and greater wear resistance
    • Easy to use / install (Ready to Fly) thanks to factory pre-assembly of pitch slider linkages and pins
    • Extra set of linkages and pins for your convenience
    TECHNICAL SPECIFICATIONS:

    • Main Body Material: Aluminum 7075-T6 – Silver anodized finish
    • Bearing Material: Chrome Steel –ABEC5 Precision Class
    • Slide Bushing Material: Low Friction Brass alloy
    • Tail Pins Material: SST
    • Assembly weight: 0.62g
    SKU: LX0904
    €20.90
    inc. VAT

     LOW STOCK
  • Lynx Heli Innovations Blade 130 X Tail Grip Set Red Devil Edition 2pcs

    Lynx Heli Innovations Blade 130 X Tail Grip Set Red Devil Edition 2pcs

    Lynx Heli Innovations 130 X Tail Grip Set Red Devil Edition 2pcs

    Lynx Heli Innovations has redesigned the standard 130 X plastic tail grip, using aluminum alloy.
    Our tail grip are weighted with integrated CNC weigh, positioned very close the tail shaft rotation center.
    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight, in particular micro helicopters tail components, were smaller weight difference  can made huge difference in final performance.
    We spent hours optimizing the design to achieve the required strength with a final weight beyond compromise. We are pilots, we expect form our upgrade a better performance.
    After many flights, we decided on a single 4x1.5x2 radial bearing design. Simple, lightweight and durable. Only 0.35g each grip assembled, with a huge increase in tail precision and strength.
    The counter couple weights are sized to reduce the servo load during fly, giving faster tail response, less vibration and increase tail servo longevity.
    The details and design of these tail grips add top performance in your 130X tail system.
    TIPS FOR THE BEST PERFORMANCE:
    Tail grip are weighted and have better performance compare the std one. Reduce 2 or 3 steep tail gyro gain to compensate Lynx tail grip efficiency.

    FEATURES:

    • Direct replacement for the standard 130 X tail parts.
    • Increase tail response and reduce vibration.
    • Preassembled with lock thread linkage balls and lubricated bearing
    • SST linkage balls to assure durability and wear resistance
    • Integrated CNC counter balace weight to reduce servo load during fly maneuvers, giving faster tail response, less vibration and increase tail servo longevity.
    • FEA (Final Elements Analysis) design assisted, achieve lightweight and maximum strength.


    TECHNICAL SPECIFICATION:

    • Tail Grip material: Aluminum 7075-T6 – red anodized finish.
    • Bearing Material: SST – ABEC5
    • Linkage Ball Material: SST
    • Assembly weight: 0.7g (the couple)
    • PACKING LIST:
    • 2 x 130 X – CNC Tail Grips factory assembly
    SKU: LX0356
    €23.90
    inc. VAT

     LOW STOCK
  • Lynx Heli InnovationsTail Grips Blade 130X

    Lynx Heli InnovationsTail Grips Blade 130X

    Lynx Heli Innovations has redesigned the standard 130 X plastic tail grip, using aluminum alloy.

    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight, in particular micro helicopters tail components, were smaller weight difference can made huge difference in final performance.
    We spent hours optimizing the design to achieve the required strength with a final weight beyond compromise.
    We are pilots, we expect form our upgrade a better performance.
    After many flights, we decided on a single 4x1.5x2 radial bearing design.
    Simple, lightweight and durable.
    Only 0.35g each grip assembled, with a huge increase in tail precision and strength.
    The counter couple weights are sized to reduce the servo load during fly, giving faster tail response, less vibration and increase tail servo longevity.
    The details and design of these tail grips add top performance in your 130X tail system.
    TIPS FOR THE BEST PERFORMANCE:
    Tail grip are weighted and have better performance compare the std one.
    Reduce 2 or 3 steep tail gyro gain to compensate Lynx tail grip efficiency.

    FEATURES:
    • Increase tail response and reduce vibration.
    • Preassembled with lock thread linkage balls and lubricated bearing
    • SST linkage balls to assure durability and wear resistance
    • Integrated CNC counter balace weight to reduce servo load during fly maneuvers, giving faster tail response, less vibration and increase tail servo longevity.
    • Direct replacement for the standard 130 X tail parts.
    • FEA (Final Elements Analysis) design assisted, achieve lightweight and maximum strength.
    TECHNICAL SPECIFICATION:

    • Tail Grip material: Aluminum 7075-T6 – anodized finish.
    • Bearing Material: SST – ABEC5 - Linkage Ball Material: SST
    • Assembly weight: 0.7g (the couple)
    PACKING LIST:

    • 2 x 130 X – CNC Tail Grips factory assembly
    SKU: LX0307
    €29.00
    inc. VAT

     IN STOCK
  • Lynx MCPX BL Head Main Grip Red

    Lynx MCPX BL Head Main Grip Red

    Lynx Heli Innovations MCPX BL Head Main Grip Red Devil Edition LX0474

    Item Description

    Lynx Heli Innovations has redesigned the standard MCPX BL plastic main grip, using  aluminum alloy.
    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight.

    The details and design of these blade grips add to the performance of your helicopter.

    Strength, durability, accurate CNC tolerances, finish, and most important lightweight.

    • These grips increase flight precision, flight after flight.
    • These grips are a direct replacement for the standard MCPX BL parts.

    Main grip material: Aluminum 7075-T6 – Red anodized finish
    Bearing material: SST – ABEC5
    Hardware:  Steel 12.9 Class - DIN 912
    Assembly weight: 1.95g

    Packing list: 

    • 2 x MCPX BL – CNC Main Grips
    • 4 x Radial bearing 5x2x1.5
    • 2 x Countersunk Pan Head Screw  M2x8
    • 2 x Lynx Red Silicone O- Ring ID 1 x W 1
    SKU: LX0474
    €30.00
    inc. VAT

     LOW STOCK
  • Lynx MCPX BL Head Main Grip Silver

    Lynx MCPX BL Head Main Grip Silver

    Lynx Heli Innovations MCPX BL Head Main Grip Silver LX0473

    Item Description

    Lynx Heli Innovations has redesigned the standard MCPX BL plastic main grip, using  aluminum alloy.

    Micro helicopter upgrades can be a trap – often they look nice but do little for function, and only add weight.

    We spent hours optimizing the design to achieve the required strength with a final weight beyond compromise. We are pilots, and we demand a light helicopter.

     
    The details and design of these blade grips add to the performance of your helicopter.
    Strength, durability, accurate CNC tolerances, finish, and most important lightweight.

    1. These grips increase flight precision, flight after flight.
    2. These grips are a direct replacement for the standard MCPX BL parts.

    Main grip material: Aluminum 7075-T6 – Silver anodized finish
    Bearing material: SST – ABEC5
    Hardware:  Steel 12.9 Class - DIN 912
    Assembly weight: 1.95g

    Packing list: 

    • MCPX BL – CNC Main Grips
    • Radial bearing 5x2x1.5
    • Countersunk Pan Head Screw  M2x8
    • Lynx Red Silicone O- Ring ID 1 x W
    SKU: LX0473-A
    €31.00
    inc. VAT

     IN STOCK
  • Lynx MCPX-BL - Air Brushed - Fiber Glass Canopy Speed Style

    Lynx MCPX-BL - Air Brushed - Fiber Glass Canopy Speed Style

    Lynx Heli Innovations introduce high quality fiber glass, hands air-brushed canopy.

    MCPX-BL have now with Lynx multiple canopy profile shape and for your fully enjoyment for each canopy shape we will made many paint design.

    Our intent is made your MCPX-BL look different but also fly great with a low weight canopy.

    Special paint and fiber glass cure process assure the best look canopy you ever looking with a superior shock resistance and an acceptable weight.

    So the next time you want to upgrade your helicopter look  – think Lynx Canopy!

    FEATURES:

    • Direct replacement for MCPX-BL canopy.
    • Newest canopy profile design and multiple options per profile design and paint color.
    • Automotive Quality paints and clear coats.
    • Professional air-brushed and finish quality
    • Incredible cost / quality rapport.

    TECHNICAL SPECIFICATION:

    • Canopy base made by High quality Fiber Glass
    • An allergic and safe Automotive Quality paints and clear coats.
    • Weight: 8gr

    PACKING LIST:

    • 1 x MCPX-BL Fiber Glass air brush canopy – Speed Style
    SKU: LXMCPX-BL022
    €15.90
    inc. VAT

     LOW STOCK

Manufacturers

Back