Scorpion Motors

Scorpion Motors

Scorpion motors became a major selling brand, great quality , decent price and performance is unmatched

Products


  • Scorpion HK-45 C-Clip Kit factory replacement C-Clip

    Scorpion HK-45 C-Clip Kit factory replacement C-Clip

    Scorpion HK-45 C-Clip Kit factory replacement C-Clip

    The Scorpion HK-45 C-Clip Kit are the factory replacement C-Clip, washers & set screw for all HK-45 Series Helicopter Motors.

    Included in the Box:

    • 4 x C-Clips
    • 4 x Set Screws
    • 4 x Washers
    SKU: HK-45C-CLIP-KIT
    €2.90
    inc. VAT

     LOW STOCK
  • Scorpion HK-4535-450KV 8mm shaft Brushless Motor Limited Edition

    Scorpion HK-4535-450KV 8mm shaft Brushless Motor Limited Edition

    Scorpion HK-4535-450KV 8mm shaft Brushless Motor Limited Edition is specially designed for a use on helicopters running on 14-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for the electric helicopter.  Special running for 14S LiPo battery deliver higher peak power and higher torque with lower running temperature.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold electro-coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    35 mm (1.38 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    5T+5T in double Wye (YY)
    • Motor Wire:    1-Strand 1.5 mm
    • Motor Kv:    450KV RPM/Volt
    • No-Load Current (Io/10V):    1.84 Amps
    • Motor Resistance (RM):    0.012 Ohms
    • Max Continuous Current:    120 Amps
    • Max Continuous Power:    6200 Watts
    • Weight:    660 Grams (23.27 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    7.98 mm (0.37 in)
    • Body Length:    67.0 mm (2.63 in)
    • Overall Shaft Length:    122.3 mm (4.81 in)
    • Max Lipo Cell:    14s
    • Max Peak Current:    216 A (2 seconds)
    • Max Peak Power:    10360 Watts (2 seconds)
    • Motor Timing:    5deg to 15 deg
    • Drive Frequency:    8kHz
    SKU: HK-4535-450KV
    €459.00
    inc. VAT

     72HR STOCK
  • Scorpion HK-4535-500KV 8mm shaft Brushless Motor Limited Edition

    Scorpion HK-4535-500KV 8mm shaft Brushless Motor Limited Edition

    Scorpion HK-4535-500KV 8mm shaft Brushless Motor Limited Edition is specially designed for a use on helicopters running on 14-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for the electric helicopter.  Special running for 14S LiPo battery deliver higher peak power and higher torque with lower running temperature.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold electro-coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm lamination to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    35 mm (1.38 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    5T+4T in double Wye (YY)
    • Motor Wire:    1-Strand 1.5 mm
    • Motor Kv:    500KV RPM/Volt
    • No-Load Current (Io/10V):    2.06 Amps
    • Motor Resistance (RM):    0.010 Ohms
    • Max Continuous Current:    125 Amps
    • Max Continuous Power:    6500 Watts
    • Weight:    664 Grams (23.41 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    7.98 mm (0.37 in)
    • Body Length:    67.0 mm (2.63 in)
    • Overall Shaft Length:    122.3 mm (4.81 in)
    • Max Lipo Cell:    14s
    • Max Peak Current:    270 (2 seconds)
    • Max Peak Power:    11880 (2 seconds)
    • Motor Timing:    5deg to 15 deg
    • Drive Frequency:    8kHz
    SKU: HK-4535-500KV
    €459.00
    inc. VAT

     72HR STOCK
  • Scorpion HK-4540-400KV 8mm shaft Brushless Motor Ultimate

    Scorpion HK-4540-400KV 8mm shaft Brushless Motor Ultimate

    Scorpion HK-4540-400KV 8mm shaft Brushless Motor Ultimate is specially designed for a use on 700~800mm blade helicopters running on 12-18cell Li-Po power. This motor represents the most technologically advanced power source ever offered for the electric helicopter.  Special running for 12-18S LiPo battery deliver higher peak power and higher torque with lower running temperature.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold electro-coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm lamination to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    40 mm (1.57 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    5T+5T in double Wye (YY)
    • Motor Wire:    1-Strand 1.5 mm
    • Motor Kv:    400KV RPM/Volt
    • No-Load Current (Io/10V):    1.65 Amps
    • Motor Resistance (RM):    0.013Ohms
    • Max Continuous Current:    150 Amps
    • Max Continuous Power:    10000 Watts
    • Weight:    719 Grams (25.35 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    7.98 mm (0.37 in)
    • Body Length:    71.9 mm (2.83 in)
    • Overall Shaft Length:    127.3 mm (5.01 in)
    • Max Lipo Cell:    12S-18S
    • Max Peak Current:    200 A (3 seconds)
    • Max Peak Power:    15000 Watts (3 seconds)
    • Motor Timing:    5deg to 15 deg
    • Drive Frequency:    8kHz
    SKU: HK-4540-400KV-ULT
    €459.00
    inc. VAT

     IN STOCK
  • Scorpion HKII 2221-6

    Scorpion HKII 2221-6

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand temperatures of up to 200 degrees C (392 F).

    All Scorpion HK Series 22mm motors come with 3.5mm male Bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller, heatshrink to cover the bullet connectors and mounting screws. Since the HK series motors are primarily designed for Helicopter and Ducted Fan use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 3.17mm shaft (1/8 inch).

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    Specifications:
    • Stator Diameter:    22.0 mm (0.87 in)
    • Stator Thickness:    21.0 mm (0.83 in)
    • No. of Stator Arms :   9
    • Magnet Poles    6
    • Motor Wind:    6 Turn Delta
    • Motor Wire:    20-Strand 0.21mm
    • Motor Kv :   4400 RPM / Volt
    • No-Load Current (Io):    2.89 Amps @ 10 volts
    • Motor Resistance (Rm):    0.016 Ohms
    • Max Continuous Current:    52 Amps
    • Max Continuous Power:    525 Watts
    • Weight:    81 Grams (2.86 oz)
    • Outside Diameter:    27.9 mm (1.098 in)
    • Shaft Diameter:    3.17 mm (0.125 in)
    • Body Length:    38.3 mm (1.508 in)
    • Overall Shaft Length :   58.7 mm (2.311 in)
    • Max Lipo Cell :   3s
    • Motor Timing  :  5deg
    • Drive Frequency  :  8kHz
    Included in the Box:
    • 1 x Scorpion HKII-2221-6 Motor
    • 3 x Female Connectors
    • 3 x Heat Shrink
    • 4 x M3 Screws
    SKU: HKII-2221-6
    €75.00
    inc. VAT

     LOW STOCK
  • Scorpion HKII 2221-8

    Scorpion HKII 2221-8

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand temperatures of up to 200 degrees C (392 F).

    All Scorpion HK Series 22mm motors come with 3.5mm male Bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller, heatshrink to cover the bullet connectors and mounting screws. Since the HK series motors are primarily designed for Helicopter and Ducted Fan use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 3.17mm shaft (1/8 inch).

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    Specifications:

    • Stator Diameter:    22.0 mm (0.87 in)
    • Stator Thickness:    21.0 mm (0.83 in)
    • No. of Stator Arms:    9
    • Magnet Poles:    6
    • Motor Wind:    8 Turn Delta
    • Motor Wire:    16-Strand 0.21mm
    • Motor Kv :   3595 RPM / Volt
    • No-Load Current (Io):    2.31 Amps @ 10 volts
    • Motor Resistance (Rm):    0.024 Ohms
    • Max Continuous Current :   45 Amps
    • Max Continuous Power:    475 Watts
    • Weight:    81 Grams (2.86 oz)
    • Outside Diameter:    27.9 mm (1.098 in)
    • Shaft Diameter:    3.17 mm (0.125 in)
    • Body Length:    38.3 mm (1.508 in)
    • Overall Shaft Length:    58.7 mm (2.311 in)
    • Max Lipo Cell :   3s
    • Motor Timing :   5deg
    • Drive Frequency:    8kHz

    Included in the Box:

    • 1 x Scorpion HKII-2221-8 Motor
    • 3 x Female Connectors
    • 3 x Heat Shrink
    • 4 x M3 Screws
    SKU: HKII-2221-8
    €85.00
    inc. VAT

     LOW STOCK
  • Scorpion HKII-2221 Bearing Maintenance Kit

    Scorpion HKII-2221 Bearing Maintenance Kit

    The Scorpion HKII-2221 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HKII-22 Series Motor.

    SKU: HK-2221-BM-Kit
    €19.99
    inc. VAT

     IN STOCK
  • Scorpion HKII-2221-10

    Scorpion HKII-2221-10

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand temperatures of up to 200 degrees C (392 F).

    All Scorpion HK Series 22mm motors come with 3.5mm male Bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller, heatshrink to cover the bullet connectors and mounting screws. Since the HK series motors are primarily designed for Helicopter and Ducted Fan use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 3.17mm shaft (1/8 inch).

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    Specifications:

    • Stator Diameter:    22.0 mm (0.87 in)
    • Stator Thickness:    21.0 mm (0.83 in)
    • No. of Stator Armsv    9
    • Magnet Poles:    6
    • Motor Wind:    10 Turn Delta
    • Motor Wire:    13-Strand 0.21mm
    • Motor Kv:    3000 RPM / Volt
    • No-Load Current (Io):    1.79 Amps @ 10 volts
    • Motor Resistance (Rm):    0.031 Ohms
    • Max Continuous Current:    42 Amps
    • Max Continuous Power:    550 Watts
    • Weight :   81 Grams (2.86 oz)
    • Outside Diameter:    27.9 mm (1.098 in)
    • Shaft Diameter:    3.17 mm (0.125 in)
    • Body Length:    38.3 mm (1.508 in)
    • Overall Shaft Length:    58.7 mm (2.311 in)
    • Max Lipo Cell:    4s
    • Motor Timing:    5deg
    • Drive Frequency:    8kHz

    Included in the Box:

    • 1 x Scorpion HKII-2221-10 Motor
    • 3 x Female Connectors
    • 3 x Heat Shrink
    • 4 x M3 Screws
    SKU: HKII-2221-10
    €72.00
    inc. VAT

  • Scorpion HKII-2221-2010KV

    Scorpion HKII-2221-2010KV

    The Scorpion HKII -Series 22mm brushless motors are designed to provide reliable power for your smaller RC aircraft and helicopter . These motors features replaceable 2.3mm prop shafts with dual ball bearings. All Scorpion HK-Series motors come with 3.5mm bullet style connectors already installed, and include a complete hardware package containing 3 matching female bullet connectors for your Speed Controller, a cross style back plate mount with screws, all in an attractive metal can package. All of the Scorpion HK-Series 22mm motors are built with a 9 tooth stator assembly, with 6 magnets in the rotor housing.

    Specifications

    Stator Diameter 22.0 mm(0.858 in)
    Stator Thickness 21.0 mm(0.819 in)
    No. of Stator Arms 9
    No. of Magnet Poles 6
    Motor Wind 16 Turn Delta
    Motor Wire 10-Strand 0.21 mm
    Motor Kv 2010 KV RPM/Volt
    No-Load Current (Io) 1.01 Amps @ 10 volts
    Motor Resistance (Rm) 0.052 Ohms
    Max Continuous Current 28 Amps
    Max Continuous Power 590 Watts
    Weight 79 Grams (2.78 oz)
    Outside Diameter 27.85 mm (1.086 in)
    Shaft Diameter 3.175 mm (0.123 in)
    Body Length 38.3 mm (1.508 in)
    Overall Shaft Length 58.7 mm (2.289 in)
    Max Lipo Cell 6s
    SKU: HKII-2221-2010
    €85.00
    inc. VAT

     LOW STOCK
  • Scorpion HKII-4235-520Kv (Nick Maxwell Edition)

    Scorpion HKII-4235-520Kv (Nick Maxwell Edition)

    Introducing our brand new motor, HKII-4235-520kv (Nick Maxwell Edition)! It is specially made for narrow frame 700 class helicopters. It has the power and performance of a HK-4525-520kv motor in a narrower motor frame. Additional to that, HKII-4235-520kv is leaser engraved with Nick Maxwell signature on the motor.

    Specifications

    Stator Diameter     42 mm (1.65 in)
    Stator Thickness     35 mm (1.38 in)
    No. of Stator Arms     12
    No. of Stator Poles     10
    Motor Wind     5+4 Turn Delta
    Motor Wire     1-Strand 1.5 mm
    Motor Kv     520KV RPM/Volt
    No-Load Current (Io/10V)     2.3 Amps
    Motor Resistance (RM)     0.012 Ohms
    Max Continuous Current     100 Amps
    Max Continuous Power     4450 Watts
    Weight     519 Grams (18.18 oz)
    Outside Diameter     52.3 mm (2.06 in)
    Shaft Diameter     5.98 mm (0.24 in)
    Body Length     61.90 mm (2.45 in)
    Overall Shaft Length     110.0 mm (4.33 in)
    Max Lipo Cell     12s
    Max Peak Current     215A (2 seconds)
    Max Peak Power     9600 Watts (2 seconds)
    Motor Timing     5deg to 15 deg
    Drive Frequency     8kHz

    SKU: HKII_4235_520
    €299.90
    inc. VAT

  • Scorpion HKII-4235-630KV (Limited Edition)

    Scorpion HKII-4235-630KV (Limited Edition)

    Introducing our brand new motor, HKII-4235-630kv, It is specially made for narrow frame 700 class helicopters. It has the power and performance of a HK-4525-630kv motor in a narrower motor frame.


    Specifications

    Specifications
    Stator Diameter     42 mm (1.65 in)
    Stator Thickness     35 mm (1.38 in)
    No. of Stator Arms     12
    No. of Stator Poles     10
    Motor Wind     4 Turn YY
    Motor Wire     1-Strand 1.6 mm
    Motor Kv     630 KV RPM/Volt
    No-Load Current (Io/10V)     3.59 Amps
    Motor Resistance (RM)     0.009 Ohms
    Max Continuous Current     120 Amps
    Max Continuous Power     5328 Watts
    Weight     522 Grams (18.27 oz)
    Outside Diameter     52.3 mm (2.06 in)
    Shaft Diameter     5.98 mm (0.24 in)
    Body Length     64.5 mm (2.54 in)
    Overall Shaft Length     112.9 mm (4.44 in)
    Max Lipo Cell     12s
    Max Peak Current     160 Amps (3 seconds)
    Max Peak Power     7100 Watts (3 seconds)
    Motor Timing     5deg to 15 deg
    Drive Frequency     8kHz

    SKU: HKII_4235_630
    €299.90
    inc. VAT

  • Scorpion HKIII-4025 Shaft Kit XL (6mm)

    Scorpion HKIII-4025 Shaft Kit XL (6mm)

    The Scorpion HK-4025 & HKIII-4025 series motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4025 & HKIII-4025 series Scorpion Helicopter Motors.

    This shaft kit is for the HK-4025 & HKIII-4025 series motors that used in newer T-600 Heli. It measures 8mm in diameter, and is 88.5mm in length. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 6mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    Included in the Box:

    • HKIII-4025 Motor Shaft Kit (6mm) -XL x1
    • Washer x 1
    • C-Clip x 2
    SKU: HK-4025-6mm-Shaft-XL
    €16.00
    inc. VAT

     IN STOCK
  • Scorpion HKIII-4035 Bearing Maintenance Kit

    Scorpion HKIII-4035 Bearing Maintenance Kit

    The Scorpion HK-4035 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HK-40 & HKIII-40 Series Motor, except the HK-4015 Series.

    SKU: HK-4035-BM-Kit
    €19.99
    inc. VAT

     LOW STOCK
  • Scorpion HKIII-4035 Motor Shaft 110mm

    Scorpion HKIII-4035 Motor Shaft 110mm

     Scorpion HK-4035 V2 & HKIII-4035 Motor Shaft Kit ( EXTRA-LONG) - 110mm

    This is the new version shaft made from a new, much stronger SKH51 Steel alloy that will hold up to the most extreme flying styles.

    • Total length of this shaft is 110mm. With 48mm of shaft exposed for pinion.
    • This shaft will get you seated correctly into the GAUI X7 motor bearing support.
    • Fits HK & HKIII 4035 series motors, Also fits the Stock GAUI X7 [GUEC GM-350S] 500KV Motor.
    • Flat spot for pinion grub screw, no grinding needed.
    • Also fits the Stock GAUI X7 (GUEC GM-350S) 500KV Motor.

    This shaft kit is for the HKIII-4035 & HK-4035 XL series motors that used in GAUI X7 Heli and measures 8mm in diameter, and is 110mm in length. The pinion end (48mm) of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 6mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    SKU: HK-4035XXL
    €36.00
    inc. VAT

  • Scorpion HKIII-5025-520KV F3S Brushless Motor Edition

    Scorpion HKIII-5025-520KV F3S Brushless Motor Edition

    Scorpion Motor HKIII-5025-520KV High Speed Racing

    The brand new Scorpion HKIII-5025-520KV F3S Edition is especially designed for use in high speed racing applications.
    With its 1-Strand 1.6mm​ winding, this motor will deliver maximum efficiency and extreme performance on 16s power.

    Specifications:

    Stator Diameter: 50.0 mm (1.97 in)
    Stator Thickness: 25.0 mm (0.98 in)
    No. of Stator Arms: 12
    Magnet Poles: 10
    Motor Wind: 6+5 Turn 2Y
    Motor Wire: 1-Strand 1.6mm
    Motor KV: 520 RPM / Volt
    No-Load Current (Io) @ 10V: 2.2 Amps
    Motor Resistance (Rm): 0.009 Ohms
    Max Continuous Current: 130 Amps
    Max Continuous Power: 7696 Watts
    Weight: 595 Grams (20.83 oz)
    Outside Diameter: 61.5 mm (2.42 in)
    Shaft Diameter: 60.2 mm (2.37 in)
    Body Length: 64.9 mm (2.56 in)
    Overall Shaft Length: 84.6 mm (3.33 in)
    Max Lipo Cell: 16s
    Max Peak Current: 200A (2 seconds)
    Max Peak Power: 11840 Watts (2 seconds)
    Motor Timing: 5deg
    Drive Frequency: 8kHz

    Weight including packaging: 1100g

    SKU: HKIII-5025-520KV
    €349.90
    inc. VAT

     72HR STOCK
  • Scorpion HKIV 4020-1060KV ,500-550 class Helicopter Brushless Motor

    Scorpion HKIV 4020-1060KV ,500-550 class Helicopter Brushless Motor

    The Scorpion HKIV 4020-1060 Brushless Motor features the same motor design and materials from the HKII-45 series motors, including the single strand winding technique, but have been updated to deliver better efficiency and power conversion than the HKIII-40mm series. With an updated EM field design, the compatibility with various speed controllers available on the market has also improved. This motor will deliver even more power to your helicopter, with increased efficiency - making it the best helicopter motor available for your 500-550 class model!

    The Scorpion HKIV Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold and black Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are all hand-wound to insure the highest copper fill rate with wire that is rated at 180 degrees C , and high voltage tested to insure that no shorts are present. The high temperature magnets used in Scorpion Motors are designed to give top performance in the most demanding applications.

    All Scorpion HKIV-4020 series motors come with the High-Current, locking style, 4mm male Bullet style connectors already attached, and include a hardware package that contains four socket head M3 x 0.5mm mounting screws, plus three 4mm female bullet connectors for your speed controller with molded plastic covers. For maximum strength, the Scorpion HKIV-4020 series motors feature an 8mm motor shaft that is ground down to a 6mm diameter at the output end to fit standard size pinion gears. Since the HKIV Series motors are primarily designed for Helicopter use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 6mm shaft.

    Scorpion Motors are built to last, and are backed with a 2-Year manufacturers warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that Scorpion cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    Specifications:

    • Stator Diameter: 40.0 mm
    • Stator Thickness: 20 mm
    • Number of Stator Slots: 12
    • Number of Magnet Poles: 10
    • Motor Wind: 4+4 Turn Delta
    • Motor Wire: 1-Strand 1.60mm
    • Motor Kv Value: 1060 RPM per Volt
    • No Load Current (Io): 4.03 Amps @ 10 Volts
    • Motor Resistance (Rm) per Phase: 0.009 Ohms
    • Maximum Continuous Current: 78 Amps
    • Max Continuous Power (6-cell Li-Po): 1732 Watts
    • Motor Weight: 310 grams
    • Outside Diameter: 49.50 mm
    • Shaft Diameter: 6 mm
    • Shaft Length, From Mounting Face: 30.8 mm
    • Motor Body Length: 49.2 mm
    • Overall Shaft Length: 71.0 mm
    • Max LiPo Cell: 6s
    • Peak Current: 90 Amps (5 seconds)
    • Peak Continuous Power: 1998 Watts
    • Motor Timing: 5deg
    • Drive Frequency: 8kHz
    SKU: HKIV-4020-1060KV
    €189.00
    inc. VAT

     IN STOCK
    NEW
  • Scorpion HKIV-4025-1100KV 600 Class Heli motor (6mm shaft)

    Scorpion HKIV-4025-1100KV 600 Class Heli motor (6mm shaft)

    This is the Fourth generation HKIV-4025 series motors. With the same motor design and materials of HKII-45 series, and single strand winding technique on this size of motor, it has the better efficiency and power conversion than HKIII-40 series, with an entirely new EM field design, while improving the compatibility with various speed controllers available on the market. This new design motor will deliver even more power to your helicopter, with increased efficiency!

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications

    • Stator Diameter    40 mm(1.57 in)
    • Stator Thickness    25 mm(0.98 in)
    • No. of Stator Arms    12
    • Magnet Poles    10
    • Motor Wind    3+3 Turn Delta
    • Motor Wire    1-Strand 1.7 mm
    • Motor Kv    1100KV RPM/Volt
    • No-Load Current (IO/10v)    5.29 Amps
    • Motor Resistance (RM)    0.006 Ohms
    • Max Continuous Current    100 Amp
    • Max Continuous Power    2220 Watt
    • Weight    347 Grams (10.58 oz)
    • Outside Diameter    49.50 mm (1.95 in)
    • Shaft Diameter    5.98 mm (0.24 in)
    • Body Length    54 mm (2.13 in)
    • Overall Shaft Length    89.9 mm (3.54 in)
    • Max Lipo Cell    6s
    • Peak Continuous Current    130 Amps (5 seconds)
    • Peak Continuous Power    2886 Watts (5 seconds)
    • Motor Timing    5deg
    • Drive Frequency    8kHz
    SKU: HKIV-4025-1100KV-6
    €199.90
    inc. VAT

     LOW STOCK
  • Scorpion Logo 600 SE HKIII-5025-440KV Brushless Motor

    Scorpion Logo 600 SE HKIII-5025-440KV Brushless Motor

    Scorpion HKIII-5025-440KV Brushless Motor is mainly designed for Logo 600 SE and also for people that want to convert their .90 size glow helicopter to electric power. This motor has a maximum continuous power rating of 4200 watts at 95 amps, and a peak power rating of 5700 watts at 130 amps! The larger diameter 50mm stator allows these motors to produce insane amounts of torque.

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    50 mm (1.56 in)
    • Stator Thickness:    25 mm (0.79 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind:    12 Turn Delta
    • Motor Wire:    19-Strand 0.33 mm
    • Motor Kv:    440KV RPM / Volt
    • No-Load Current (Io/10V):    1.15 Amps
    • Motor Resistance (Rm):    0.015 Ohms
    • Max Continuous Current:    95 Amps
    • Max Continuous Power:    4200 Watts
    • Weight:    566 Grams (19.96 oz)
    • Outside Diameter:    62.1 mm (2.44 in)
    • Shaft Diameter:    5.98 mm (0.24 in)
    • Body Length:    58.7 mm (2.31 in)
    • Overall Shaft Length:    104.30 mm (4.11 in)
    • Max Lipo Cell:    14s
    • Peak Current:    120A (5 seconds)
    • Peal Power:    5320 Watts (5 seconds)
    • Motor Timing :   5deg
    • Drive Frequency:    8kHz
    SKU: HKIII-5025-440KV
    €274.99
    inc. VAT

     LOW STOCK
  • Scorpion Motor Bearing Lubrication Kit

    Scorpion Motor Bearing Lubrication Kit

    The Scorpion Motor Bearing Lubrication Kit will help you maintain the bearings in your Scorpion brushless electric motor. Today's brushless motors, especially the helicopter motors, can be pretty hard on the bearings. In an average flight, the motor in a 450 size helicopter spins around almost a quarter million times! Without proper lubrication, the balls in the bearings can wear out quickly, leading to premature failure. At these speeds, the oil can get thrown out of the bearings in as little as 10-15 flights. Once the bearings loose their lubrication, they can heat up and wear out very quickly. A small drop placed on each bearing about once every 10-15 flights is enough to maintain proper lubrication to insure the longest possible life for your motor bearings.

    The oil included in this kit contains everything necessary to keep your motor bearings in top condition. The specially designed oil not only lubricates, it also bonds to the metal parts, displaces moisture and prevents corrosion to extend the life of your motor bearings.

    The oil is safe for use on Acrylics, Polyester, Nylon, Vinyl, Delrin, Teflon, Formica, Polyethylene and Polypropylene. It is also safe on most painted surfaces. There is no visible effect on Buna-N, Viton or Neoprene rubber products, so it is safe around most fuel lines, O-rings and other rubber products.

    The Scorpion Motor Bearing Lubrication Kit contains a 30ml bottle of bearing lubricant, a leak-proof twist-on cap, and a needle point applicator (19.5mm in length, 1.3mm in diameter) with protective cover.

    SKU: Lubrication_Kit
    €8.00
    inc. VAT

  • Scorpion motor HEAVY DUTY HK 4550-330KV

    Scorpion motor HEAVY DUTY HK 4550-330KV

    Scorpion motor HEAVY DUTY HK 4550-330KV Specifications

    Motor Wind    5+4T YY
    Motor Wire    1 strand  1.5mm
    Motor Kv    330 RPM / Volt
    Outside Diameter    56.4 mm
    Shaft Diameter    5.98 mm
    Body Length    93.7 mm
    Overall Shaft Length  20 mm
     

    SKU: HK4550-330
    €469.00
    inc. VAT

     72HR STOCK
  • Scorpion Motor HK 4525-370Kv LOGO 690 special edition

    Scorpion Motor HK 4525-370Kv LOGO 690 special edition

    Scorpion Motor HK 4525-370Kv LOGO 690 special edition
    SKU: MIK-4891
    €295.00
    inc. VAT

     72HR STOCK
  • Scorpion Motor HK 4525-380Kv LOGO 690 special edition

    Scorpion Motor HK 4525-380Kv LOGO 690 special edition

    Scorpion Motor HK 4525-380Kv Mikado LOGO 690 special edition

    SKU: MIK-4525-380
    €295.00
    inc. VAT

     LOW STOCK
  • Scorpion Motor HK-3226-1900KV

    Scorpion Motor HK-3226-1900KV

    Description:

    Scorpion HK-3226 motors have been developed for the 500 class electric helicopters (425-450mm blade). These motors are designed to provide all the power that you can use, while still maintaining excellent efficiency and cool running characteristics.

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts. Unlike other motor manufactures that use off-the-shelf NdFeB magnets with a maximum Curie temperature of 80 to 100 degrees C, our motor magnets are custom manufactured to be able to withstand high temperatures. The wire we use to wind the stators is rated to 180 degrees C (356 F), so it can take the heat and keep on performing.

    All Scorpion HK-3226 series motors come with 4mm male Bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller with matching heat shrink tubing. Since the HK series motors are primarily designed for Helicopter and Ducted Fan use, they do not include a prop adapter. If you intend on running a prop on this motor, you will need to purchase a prop adapter for a 5mm shaft.

    Specifications:

    • Stator Diameter: 32.0 mm (1.26 in)
    • Stator Thickness: 26.0 mm (1.02 in)
    • Motor Kv: 1900Kv RPM/Volt

     

    SKU: HK-3226-1900
    €129.99
    inc. VAT

     LOW STOCK
  • Scorpion motor HK-4530 Shaft Kit XL (6mm 37mm)

    Scorpion motor HK-4530 Shaft Kit XL (6mm 37mm)

    The Scorpion HK-4530 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4530 series Scorpion Helicopter Motors.

    The shaft for the HK-4530 series motors measures 10mm in diameter, and is 100mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    SKU: HK_4530_6mm_37
    €38.00
    inc. VAT

     LOW STOCK

Manufacturers

Back