Scorpion Motors

Scorpion Motors

Scorpion motors became a major selling brand, great quality , decent price and performance is unmatched

Products


  • Scorpion 700 Class Electric Heli HKIII-5020-520KV Brushless Motor

    Scorpion 700 Class Electric Heli HKIII-5020-520KV Brushless Motor

    Scorpion HKIII-5020-520KV Brushless Motor is designed for 700 class Electric Helicopters, and for people that want to convert their .90 size glow helicopter to electric power. This motor has a maximum continuous power rating of 3770 watts at 85 amps, and a peak power rating of 5320 watts at 120 amps! The larger diameter 50mm stator allows these motors to produce insane amounts of torque.

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    50 mm (1.56 in)
    • Stator Thickness:    20 mm (0.79 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind :   13 Turn Delta
    • Motor Wire:    19-Strand 0.33 mm
    • Motor Kv:    520KV RPM / Volt
    • No-Load Current (Io/10V):    1.26 Amps
    • Motor Resistance (Rm):    0.014 Ohms
    • Max Continuous Current:    90 Amps
    • Max Continuous Power:    4000 Watts
    • Weight:    498 Grams (17.56 oz)
    • Outside Diameter:    62.1 mm (2.44 in)
    • Shaft Diameter:    5.98 mm (0.24 in)
    • Body Length:    53.7 mm (2.11 in)
    • Overall Shaft Length:    98.30 mm (3.87 in)
    • Max Lipo Cell:    12s
    • Peak Current :   120A (5 seconds)
    • Peal Power:    5320 Watts (5 seconds)
    • Motor Timing:    5deg
    • Drive Frequency:    8kHz
    SKU: HKIII-5020-520KV
    €239.99
    inc. VAT

     LOW STOCK
  • Scorpion 700 Class Heli HK-4530-450KV Brushless Motor Limited Edition

    Scorpion 700 Class Heli HK-4530-450KV Brushless Motor Limited Edition

    Scorpion HK-4530-450KV Brushless Motor Limited Edition is specially designed for a use on 700 class helicopters running on 14-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter and also produces 20% more torque than the Scorpion popular HKIII-4035 series motors and exceed 90% efficiency.

    Each of the new HK-4530-450KV Limited Edition motor is wound with a single strand of 1.4mm wire for the highest possible efficiency. This motor is capable of running continuously at an input power of 5400 watts at 110 amps, and can handle peak inputs of 9600 watts and 200 amps for 2 seconds.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    30 mm (1.18 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    6T+5T in double Wye
    • Motor Wire:    1-Strand 1.4 mm
    • Motor Kv:    450KV RPM/Volt
    • No-Load Current (Io/10V):    1.71 Amps
    • Motor Resistance (RM):    0.0130 Ohms
    • Max Continuous Current:    110 Amps
    • Max Continuous Power:    5400 Watts
    • Weight:    565 Grams (17.25 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    5.98 mm (0.24 in)
    • Body Length :   60.6 mm (2.39 in)
    • Overall Shaft Length:    100.0 mm (3.94 in)
    • Max Lipo Cell:    14s (for Best Setup)
    • Max Peak Current:    200A (2 seconds)
    • Max Peak Power:    9600 Watts (2 seconds)
    • Motor Timing:    5deg to 15deg
    • Drive Frequency:    8kHz

    Included in the Box:

    • 1 x Scorpion HK-4530-450KV Motor
    • 3x Female 6mm Connectors
    • 3x Heat Shrink  

    Note:

    • *This motor is using 30mm bolt spacing on the mounting with M4 Screw holes
    SKU: HK-4530-450KV
    €329.00
    inc. VAT

  • Scorpion 700 Class Heli HK-4530-500KV 6mm shaft Brushless Motor Limited Edition

    Scorpion 700 Class Heli HK-4530-500KV 6mm shaft Brushless Motor Limited Edition

    Scorpion HK-4530-500KV 6mm shaft Brushless Motor Limited Edition is specially designed for a use  on 700 class helicopters running on 12-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter and also produces 20% more torque than the Scorpion popular HKIII-4035 series motors and exceed 89% efficiency.

    Each of the new HK-4530-500KV Limited Edition motor is wound with a single strand of 1.5mm wire for the highest possible efficiency. This motor is capable of running continuously at an input power of 4800 watts at 115 amps, and can handle peak inputs of 11000 watts and 250 amps for 2 seconds.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    30 mm (1.18 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    5T+5T Turn Wye
    • Motor Wire:    1-Strand 1.5 mm
    • Motor Kv:    500KV RPM/Volt
    • No-Load Current (Io/10V):    1.85 Amps
    • Motor Resistance (RM):    0.0107 Ohms
    • Max Continuous Current:    115 Amps
    • Max Continuous Power:    4800 Watts
    • Weight :   565 Grams (17.25 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    5.98 mm (0.24 in)
    • Body Length:    60.6 mm (2.39 in)
    • Overall Shaft Length:    100.0 mm (3.94 in)
    • Max Lipo Cell:    12s
    • Max Peak Current:    250A (2 seconds)
    • Max Peak Power:    11000 Watts (2 seconds)
    • Motor Timing:    5deg to 15 deg
    • Drive Frequency:    8kHz

    Included in the Box:

    • 1 x Scorpion HK-4530-500KV Motor

    Note:

    • *This motor is using 30mm bolt spacing on the mounting with M4 Screw holes
    • * Gold connectors are not soldered nor included

    SKU: HK-4530-500KV
    €339.00
    inc. VAT

     LOW STOCK
  • Scorpion 700 Class Heli HK-4530-540KV Brushless Motor Limited Edition

    Scorpion 700 Class Heli HK-4530-540KV Brushless Motor Limited Edition

    Scorpion HK-4530-540KV Brushless Motor Limited Edition is specially designed for a use on 700 class helicopters running on 12-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter and also produces 20% more torque than the Scorpion popular HK4035 series motors and exceed 89% efficiency.

    Each of the new HK-4530-540KV Limited Edition motor is wound with a single strand of 1.5mm wire for the highest possible efficiency. This motor is capable of running continuously at an input power of 4800 watts at 115 amps, and can handle peak inputs of 11000 watts and 250 amps for 2 seconds.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    30 mm (1.18 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    9 Turn Wye
    • Motor Wire:    1-Strand 1.5 mm
    • Motor Kv:    540KV RPM/Volt
    • No-Load Current (Io/10V):    2.11 Amps
    • Motor Resistance (RM):    0.010 Ohms
    • Max Continuous Current:    115 Amps
    • Max Continuous Power:    4800 Watts
    • Weight:    565 Grams (17.25 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    5.98 mm (0.24 in)
    • Body Length:    60.6 mm (2.39 in)
    • Overall Shaft Length:    100.0 mm (3.94 in)
    • Max Lipo Cell:    12s
    • Max Peak Current:    250A (2 seconds)
    • Max Peak Power:    11000 Watts (2 seconds)
    • Motor Timing :   5deg to 15 deg
    • Drive Frequency:    8kHz

    Included in the Box:

    • 1 x Scorpion HK-4530-540KV Motor

    Note:

    • *This motor is using 30mm bolt spacing on the mounting with M4 Screw holes
    • * Gold connectors are not soldered nor included

    SKU: HK-4530-540KV
    €329.00
    inc. VAT

     72HR STOCK
  • Scorpion 700 Class Heli HKII-4525-520KV ULTIMATE Brushless Motor

    Scorpion 700 Class Heli HKII-4525-520KV ULTIMATE Brushless Motor

    HK-4525 has been the motor of choice for 700-class RC helicopters, and has become the performance benchmark for every other model motor manufacturer. Eighteen months later, in April of 2012, we released an improved version of this motor, the HK-4525-520kv Ultimate Edition. Since then, the Ultimate Edition motor has proven itself to be extremely successful in heli competitions, and has become the most popular motor used in competition 700-class helicopters world-wide.

    Many other motor manufacturers have tried to compete with this motor, but none have been successful. We even tried for years to improve the HK-4525-520 motor but were unable to do so. Finally, after nearly 5 years of testing and development, we are pleased to announce the release of the new next generation HKII-4525-520kv Ultimate motor.

    Through improvements in motor design and materials, we have been able to increase the efficiency and power conversion of this motor with an entirely new EM field design, while improving the compatibility with various speed controllers available on the market. This new design motor will deliver even more power to your helicopter, with increased efficiency!

    With the new HKII-4525-520kv Ultimate motor, we have once again raised the bar and created a new benchmark for 700-class helicopter power!

    Each of the new HKII-4525-520KV ULTIMATE motor is wound with a single strand of 1.4mm wire for the highest possible efficiency. This motor is capable of running continuously at an input power of 4450 watts at 100 amps, and can handle peak inputs of 10200 watts and 230 amps for 2 seconds

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    *This motor is using 30mm bolt spacing on the mounting with M4 Screw holes
    Scorpion HKII-4525-520KV – ULTIMATE Specifications

    • Stator Diameter     45 mm (1.77 in)
    • Stator Thickness     25 mm (0.98 in)
    • No. of Stator Arms     12
    • No. of Stator Poles     10
    • Motor Wind     5+6T YY
    • Motor Wire     1-Strand 1.4 mm
    • Motor Kv     520KV RPM/Volt
    • No-Load Current (Io/10V)     1.81 Amps
    • Motor Resistance (RM)     0.012 Ohms
    • Max Continuous Current     100 Amps
    • Max Continuous Power     4450 Watts
    • Weight     516 Grams (18.20oz)
    • Outside Diameter     56.9 mm (2.24 in)
    • Shaft Diameter     5.98 mm (0.24 in)
    • Body Length     57.7 mm (2.27 in)
    • Overall Shaft Length     112 mm (4.41 in)
    • Max Lipo Cell     12s
    • Max Peak Current     230A (2 seconds)
    • Max Peak Power     10200 Watts (2 seconds)
    • Motor Timing     5deg to 15 deg
    • Drive Frequency     8kHz
    SKU: HKII-4525-520-ULT
    €359.00
    inc. VAT

     IN STOCK
  • Scorpion 700 Class Heli HKIII-4035-450KV Brushless Motor

    Scorpion 700 Class Heli HKIII-4035-450KV Brushless Motor

    Scorpion HKIII-4035-450KV Brushless Motor is specially designed for a use on 700 class helicopters running on 12-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    40 mm (1.57 in)
    • Stator Thickness:    35 mm (1.024 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind:    10 Turn Delta
    • Motor Wire:    26 - Strand 0.25mm
    • Motor Kv:    450KV RPM / Volt
    • No-Load Current (IO):    1.85 Amps @ 10v
    • Motor Resistance (RM) :   0.020 Ohms
    • Max Continuous Current:    75 Amps
    • Max Continuous Power :   3300 Watts
    • Weight:    460 Grams (16.22 oz)
    • Outside Diameter:    49.98 mm (1.97 in)
    • Shaft Diameter:    5.98 mm (0.235 in)
    • Body Length:    61.8 mm (2.43 in)
    • Overall Shaft Length:    100.0 mm (3.93 in)
    • Max Lipo Cell:    12s
    • Peak Current:    95A (5 seconds)
    • Peak Power:    4200 Watts (5 seconds)
    • Motor Timing:    5deg
    • Drive Frequency:    8kHz   

    Note:

    • *This motor is using 30mm*25mm bolt spacing on the mounting with M4 Screw holes
    SKU: HKIII-4035-450
    €199.00
    inc. VAT

  • Scorpion 700 Class Heli HKIII-4035-500KV Brushless Motor

    Scorpion 700 Class Heli HKIII-4035-500KV Brushless Motor

    Scorpion HKIII-4035-500KV Brushless Motor is specially designed for a use on 700 class helicopters running on 12-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:
    • Stator Diameter:    40 mm (1.57 in)
    • Stator Thickness:    35 mm (1.024 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind :   9 Turn Delta
    • Motor Wire:    21 - Strand 0.29mm
    • Motor Kv:    500KV RPM / Volt
    • No-Load Current (IO) :   2.02 Amps @ 10v
    • Motor Resistance (RM):    0.016 Ohms
    • Max Continuous Current:    84 Amps
    • Max Continuous Power:    3500 Watts
    • Weight:    460 Grams (16.22 oz)
    • Outside Diameter:    49.98 mm (1.97 in)
    • Shaft Diameter:    5.98 mm (0.235 in)
    • Body Length:    61.8 mm (2.43 in)
    • Overall Shaft Length:    100.0 mm (3.93 in)
    • Max Lipo Cell:    12s
    • Peak Current:    104A (5 seconds)
    • Peak Power:    4600 Watts (5 seconds)
    • Motor Timing:    5deg
    • Drive Frequency:    8kHz
    Note:
    • *This motor is using 30mm*25mm bolt spacing on the mounting with M4 Screw holes
    SKU: HKIII-4035-500
    €199.00
    inc. VAT

     72HR STOCK
  • Scorpion 700 Class Heli HKIII-4035-530KV Brushless Motor

    Scorpion 700 Class Heli HKIII-4035-530KV Brushless Motor

    Scorpion HKIII-4035-530KV Brushless Motor is specially designed for a use on 700 class helicopters running on 12-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:
    • Stator Diameter:    40 mm (1.57 in)
    • Stator Thickness:    35 mm (1.024 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind:    9 Turn Delta
    • Motor Wire:    22 - Strand 0.29mm
    • Motor Kv:    530KV RPM / Volt
    • No-Load Current (IO):    2.15 Amps @ 10v
    • Motor Resistance (RM):    0.015 Ohms
    • Max Continuous Current:    80 Amps
    • Max Continuous Power:    3400 Watts
    • Weight:    460 Grams (16.22 oz)
    • Outside Diameter:    49.98 mm (1.97 in)
    • Shaft Diameter:    5.98 mm (0.235 in)
    • Body Length:    61.8 mm (2.43 in)
    • Overall Shaft Length:    100.0 mm (3.93 in)
    • Max Lipo Cell:    12s
    • Peak Current:    100A (5 seconds)
    • Peak Power:    4400 Watts (5 seconds)
    • Motor Timing:    5deg
    • Drive Frequency:    8kHz
    Note:
    • *This motor is using 30mm*25mm bolt spacing on the mounting with M4 Screw holes
    SKU: HKIII-4035-530
    €199.00
    inc. VAT

     72HR STOCK
  • Scorpion 700 Class Heli HKIII-4035-560KV Brushless Motor

    Scorpion 700 Class Heli HKIII-4035-560KV Brushless Motor

    Scorpion 700 Class Heli HKIII-4035-560KV Brushless Motor is specially designed for a use on 700 class helicopters running on 12-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for a 700 class electric helicopter.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    40 mm (1.57 in)
    • Stator Thickness:    35 mm (1.024 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind:    8 Turn Delta
    • Motor Wire:    23 - Strand 0.29mm
    • Motor Kv:    560KV RPM / Volt
    • No-Load Current (IO):    2.24 Amps @ 10v
    • Motor Resistance (RM):    0.014 Ohms
    • Max Continuous Current:    100 Amps
    • Max Continuous Power:    4200 Watts
    • Weight:    460 Grams (16.22 oz)
    • Outside Diameter:    49.98 mm (1.97 in)
    • Shaft Diameter:    5.98 mm (0.235 in)
    • Body Length:    61.8 mm (2.43 in)
    • Overall Shaft Length:    100.0 mm (3.93 in)
    • Max Lipo Cell:    12s
    • Peak Current :   120A (5 seconds)
    • Peak Power :   5200 Watts (5 seconds)
    • Motor Timing :   5deg
    • Drive Frequency :   8kHz

    Note:

    • *This motor is using 30mm*25mm bolt spacing on the mounting with M4 Screw holes
    SKU: HKIII-4035-560
    €199.00
    inc. VAT

     72HR STOCK
  • Scorpion 800 Class Electric Heli HK-5035-500KV Brushless Motor

    Scorpion 800 Class Electric Heli HK-5035-500KV Brushless Motor

    The Scorpion HK-5035-500 motor will provide all the power you need for the larger 800 class electric helicopters, those massive electric powered scale projects or for your workhorse camera platform helicopters that need to be able to lift heavy weights reliably.

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:
    • Stator Diameter:    50 mm (1.56 in)
    • Stator Thickness:    35 mm (1.37 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    8
    • Motor Wind:    9 Turn Delta
    • Motor Wire:    26-Strand 0.33 mm
    • Motor Kv:    500KV RPM / Volt
    • No-Load Current (Io/10V):    1.03 Amps
    • Motor Resistance (Rm):    0.012 Ohms
    • Max Continuous Current :   120 Amps
    • Max Continuous Power:    5400 Watts
    • Weight:    670 Grams (23.45 oz)
    • Outside Diameter:    61.0 mm (2.4 in)
    • Shaft Diameter:    7.98 mm (0.3 in)
    • Body Length:    66.0 mm (2.59 in)
    • Overall Shaft Length:    100.75 mm (3.97 in)
    • Max Lipo Cell:    12s
    • Peak Current :   160A (5 seconds)
    • Peal Power:    7100 Watts (5 seconds)
    SKU: HK-5035-500
    €329.00
    inc. VAT

     LOW STOCK
  • Scorpion 800 Class Electric Heli HKIII-5035-410KV Brushless Motor

    Scorpion 800 Class Electric Heli HKIII-5035-410KV Brushless Motor

    Scorpion HKIII-5035-410KV Brushless Motor will provide all the power you need for the larger 800 class electric helicopters, those massive electric powered scale projects or for your workhorse camera platform helicopters that need to be able to lift heavy weights reliably.

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with high quality laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    50 mm (1.56 in)
    • Stator Thickness:    35 mm (1.38 in)
    • No. of Stator Arms:    12
    • Magnet Poles:    10
    • Motor Wind:    9 Turn Delta
    • Motor Wire:    24-Strand 0.33 mm
    • Motor Kv:    410KV RPM / Volt
    • No-Load Current (Io/10V):    1.53 Amps
    • Motor Resistance (Rm):    0.012 Ohms
    • Max Continuous Current:    105 Amps
    • Max Continuous Power:    5100 Watts
    • Weight:    742 Grams (26.16 oz)
    • Outside Diameter:    62.1 mm (2.44 in)
    • Shaft Diameter:    5.98 mm (0.24 in)
    • Body Length:    68.70 mm (2.70 in)
    • Overall Shaft Length:    119.30 mm (4.70 in)
    • Max Lipo Cell:    14s
    • Peak Current:    145A (5 seconds)
    • Peal Power:    7000 Watts (5 seconds)
    • Motor Timing:    5deg
    • Drive Frequency:    8kHz
    SKU: HKIII-5035-410KV
    €329.00
    inc. VAT

     72HR STOCK
  • Scorpion Commander 15V 45A ESC SBEC (V3)

    Scorpion Commander 15V 45A ESC SBEC (V3)

    The Commander 4S SBEC series ESC(V3) operates from 6 to 17V. It features switching BEC will convert the voltage from your battery packs to 5V to power your receiver and servos. The Commander SBEC will deliver 3 Amps of continuous current with 5 Amps bursts. And can handle up to 4 digital servos or 5 standard servos on fix wing models. With a Switching type BEC, the BEC is not needed to de-rate as the input voltage increases. The full 3 Amps of BEC current is available for input between 2-cell to 4-cell Lipo operation.

    Specifications:

    • Weight (Without Connectors):    44 g (1.55 oz)
    • Max Continuous Current:    45 Amps
    • Operating Voltage Range:    5 to 17 Volts
    • Max BEC Output:    5 Amps @ 5 V
    • On Resistance:    2.33 mOhms
    • Size:    72 x 30 x 8 mm (2.83 x 1.18 x 0.315 in)

    Included in the Box:

    • 1 x Scorpion Commander 15V 45A ESC
    • 1 x Instruction Manual

    Note:

    • *ARE NOT INCLUDED IR Transmitter (Programming Card) & IR RECEIVER
    SKU: 4S-45-SBEC-V3
    €59.90
    inc. VAT

     72HR STOCK
  • Scorpion Commander V 50V 130A ESC (OPTO)

    Scorpion Commander V 50V 130A ESC (OPTO)

    This fifth generation of Scorpion Commander V 50V OPTO series features with new external governor mode (AIR 2) for auto throttle calibration, it also included an external adapter for future firmware update by PC through Commander V link Cable.

    Specifications:

    • Weight (Without Connectors)    184g (6.49 oz)
    • Max Continuous Current    130 Amps
    • Operating Voltage Range    12 to 50 Volts
    • Max BEC Output    No BEC
    • On Resistance    0.68 mOhms
    • Size    89 x 43 x 25.5mm (3.5 x 1.69 x 1.00 in)
    • Weight including packaging: 452g

    SKU: SP-12S-COM130-OPTO
    €249.00
    inc. VAT

     72HR STOCK
  • Scorpion HK-22 C-Clip Kit factory replacement C-Clip

    Scorpion HK-22 C-Clip Kit factory replacement C-Clip

    Scorpion HK-22 C-Clip Kit factory replacement C-Clip

    The Scorpion HK-22 C-Clip Kit are the factory replacement C-Clip, washers & set screw for all HK-22 Series Helicopter Motors. (Except HK-2206)

    Included in the Box:

    • 4 x C-Clips
    • 4 x Set Screws
    • 4 x Washers
    SKU: HK-22C-CLIP-KIT
    €2.00
    inc. VAT

  • Scorpion HK-3014-900KV Motor, Goblin 380 special

    Scorpion HK-3014-900KV Motor, Goblin 380 special

    The Scorpion HK-30 series motors have been developed for the newer electric helicopter that are now coming onto the market. This HK-3014-900 KV motor designed to provide long flight time and power that you need to use for Goblin 380, while still maintaining excellent efficiency and cool running characteristics.

    Scorpion HK-30 Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to with stand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    This motors come with 4.0mm male bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller with matching heat shrink tubing. For maximum strength, motors feature an 5 mm diameter at the output shaft to fit standard size pinion gears.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications
    Stator Diameter    30.0 mm(1.181 in)
    Stator Thickness    14.0 mm(0.551 in)
    No.of stator Arms    12
    No.of stator Poles    10
    Motor Wind    11T Turn Delta
    Motor Wire    7-Strand 0.25 mm
    Motor Kv    900KV RPM/Volt
    No-Load Current    (IO/10V) 1.09 Amps
    Motor Resistance(RM)    0.065 Ohms
    Max Continuous Current    28 Amps
    Max Continuous Power    650Watts
    Weight    119 Grams (4.19 oz)
    Outside Diameter    37.5 mm (1.476 in)
    Shaft Diameter    4.98 mm (0.196 in)
    Body Length    34.5 mm (1.358 in)
    Overall Shaft Length    57.0 mm (2.244 in)
    Max. Peak Current    43 Amp (2 Seconds)
    Max. Peak Power    1000 Watts (2 Seconds)
    Max Lipo    6S
    Included in the Box
    1 x Scorpion HK-3014-900KV 5mm shaft motor
    3 x Female Connectors
    3 x Heat Shrink
    4 x M3*0.5 Screws

    SKU: HK-3014-900KV
    €115.00
    inc. VAT

  • Scorpion HK-3020-1000KV Motor, Goblin 380 special

    Scorpion HK-3020-1000KV Motor, Goblin 380 special

    The Scorpion HK-30 series motors have been developed for the newer electric helicopter that are now coming onto the market. This HK-3020-1000 KV motor designed to provide all the crazy power that you even can't imagine for Goblin 380, while still maintaining excellent efficiency and cool running characteristics.

    Scorpion HK-30 Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to with stand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    This motors come with 4.0mm male bullet style connectors already attached, and include a hardware package that contains 3 matching female Bullet connectors for your speed controller with matching heat shrink tubing. For maximum strength, motors feature an 5 mm diameter at the output shaft to fit standard size pinion gears.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications

    • Stator Diameter    30.0 mm(1.181 in)
    • Stator Thickness    20.0 mm(0.787 in)
    • No. of stator Arms    12
    • No. of stator Poles    10
    • Motor Wind    6+7 Turn Delta
    • Motor Wire    12-Strand 0.25 mm
    • Motor Kv    1000KV RPM/Volt
    • No-Load Current    (IO/10V) 1.75 Amps
    • Motor Resistance(RM)    0.030 Ohms
    • Max Continuous Current    45 Amps
    • Max Continuous Power    1050 Watts
    • Weight    153 Grams (5.39 oz)
    • Outside Diameter    37.5 mm (1.476 in)
    • Shaft Diameter    4.98 mm (0.196 in)
    • Body Length    40.5 mm (1.594 in)
    • Overall Shaft Length    63.0 mm (2.480 in)
    • Max. Peak Current    70 Amp (2 Seconds)
    • Max. Peak Power    1600Watts (2 Seconds)
    • Max. Lipo    6S
    Included in the Box

    • 1 x Scorpion HK-3020-1000KV 5mm shaft motor
    • 3 x Female Connectors
    • 3 x Heat Shrink
    • 4 x M3*0.5 Screws
    SKU: HK-3020-1000KV
    €109.00
    inc. VAT

  • Scorpion HK-3026 Bearing Maintenance Kit

    Scorpion HK-3026 Bearing Maintenance Kit

    The Scorpion HK-3026 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HK-30 Series Motor.

    SKU: HK-3026-M-Kit
    €19.99
    inc. VAT

     IN STOCK
  • Scorpion HK-40 C-Clip Kit factory replacement C-Clip

    Scorpion HK-40 C-Clip Kit factory replacement C-Clip

    Scorpion HK-40 C-Clip Kit factory replacement C-Clip

    The Scorpion HK-40 C-Clip Kit are the factory replacement C-Clip, washers & set screw HK-4020, HK-4025, HK-4035 & all HKIII-40 Series Helicopter Motors. (Except HK-4015)

    Included in the Box:

    • 4 x C-Clips
    • 4 x Set Screws
    • 4 x Washers
    SKU: HK-40C-CLIP-KIT1
    €2.50
    inc. VAT

     IN STOCK
  • Scorpion HK-4020 Motor Shaft 5mm

    Scorpion HK-4020 Motor Shaft 5mm

    HKIII-4020 Shaft Kit (5mm 31mm)

    The Scorpion HK-4020, HKIII-4025 & HKIV-4025 motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4020, HKIII-4025 & HKIV-4025 series Scorpion Helicopter Motors.

    The shaft for the HK-4020, HKIII-4025 & HKIV-4025 series motors measures 8mm in diameter, and is 78.7mm in long. The Stock HK-4020, HKIII-4025 & HKIV-4025 motors have a 5mm output shaft end on them to allow the user to install 5mm pinion gears. The shaft kit will also fit other brushless motors that require an 8mm shaft of this length with a 5mm end. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    SKU: HKIII-4020-Shaft
    €9.99
    inc. VAT

     IN STOCK
  • Scorpion HK-4025 Motor Shaft 6mm

    Scorpion HK-4025 Motor Shaft 6mm

    Special shaft for 4025 motors, with extra Long extention, 30mm.

    Very easy to use with Logo motor bearing mount.

    Diameter of the shaft is 6mm

    SKU: HK-4025SHAFT6
    €16.00
    inc. VAT

     IN STOCK
  • Scorpion HK-4035 Motor Shaft 5mm-95mm

    Scorpion HK-4035 Motor Shaft 5mm-95mm

    The Scorpion HK-4035 motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4035 series Scorpion Helicopter Motors.

    The shaft for the HK-4035 series motors measures 8mm in diameter, and is 94.7mm in long. The pinion end of this shaft is ground down to 5mm to allow the user to install 5mm pinion gears. The shaft kit will also fit other brushless motors that require a 5mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    Included in the Box

    - HK4035 Motor Shaft (5mm) x1
    - Washer x 1
    - C-Clip x 2

    SKU: HK-4035SHAFT5
    €35.00
    inc. VAT

     IN STOCK
    NEW
  • Scorpion HK-4035 Motor Shaft 6mm-95mm

    Scorpion HK-4035 Motor Shaft 6mm-95mm

    The Scorpion HK-4035 motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4035 series Scorpion Helicopter Motors.

    The shaft for the HK-4035 series motors measures 8mm in diameter, and is 94.7mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 6mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    Included in the Box

    - HK4035 Motor Shaft (6mm) x1
    - Washer x 1
    - C-Clip x 2

    SKU: HK-4035SHAFT6
    €35.00
    inc. VAT

     LOW STOCK
  • Scorpion HK-45 C-Clip Kit factory replacement C-Clip

    Scorpion HK-45 C-Clip Kit factory replacement C-Clip

    Scorpion HK-45 C-Clip Kit factory replacement C-Clip

    The Scorpion HK-45 C-Clip Kit are the factory replacement C-Clip, washers & set screw for all HK-45 Series Helicopter Motors.

    Included in the Box:

    • 4 x C-Clips
    • 4 x Set Screws
    • 4 x Washers
    SKU: HK-45C-CLIP-KIT
    €2.90
    inc. VAT

     LOW STOCK
  • Scorpion HK-4535-450KV 8mm shaft Brushless Motor Limited Edition

    Scorpion HK-4535-450KV 8mm shaft Brushless Motor Limited Edition

    Scorpion HK-4535-450KV 8mm shaft Brushless Motor Limited Edition is specially designed for a use on helicopters running on 14-cell Li-Po power. This motor represents the most technologically advanced power source ever offered for the electric helicopter.  Special running for 14S LiPo battery deliver higher peak power and higher torque with lower running temperature.

    Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold electro-coated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are custom manufactured to be able to withstand high temperatures, making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter:    45 mm (1.77 in)
    • Stator Thickness:    35 mm (1.38 in)
    • No. of Stator Arms:    12
    • No. of Stator Poles:    10
    • Motor Wind:    5T+5T in double Wye (YY)
    • Motor Wire:    1-Strand 1.5 mm
    • Motor Kv:    450KV RPM/Volt
    • No-Load Current (Io/10V):    1.84 Amps
    • Motor Resistance (RM):    0.012 Ohms
    • Max Continuous Current:    120 Amps
    • Max Continuous Power:    6200 Watts
    • Weight:    660 Grams (23.27 oz)
    • Outside Diameter:    56.7 mm (2.23 in)
    • Shaft Diameter:    7.98 mm (0.37 in)
    • Body Length:    67.0 mm (2.63 in)
    • Overall Shaft Length:    122.3 mm (4.81 in)
    • Max Lipo Cell:    14s
    • Max Peak Current:    216 A (2 seconds)
    • Max Peak Power:    10360 Watts (2 seconds)
    • Motor Timing:    5deg to 15 deg
    • Drive Frequency:    8kHz
    SKU: HK-4535-450KV
    €459.00
    inc. VAT

     LOW STOCK

Manufacturers

Back