S-BUS

S-BUS

Futaba S.Bus System - Revolutionary, cutting-edge technology, allow you to put many channels on same cable of 3 wires.
Secure, and excellent solution for any aircraft, especially with many long wires.

Products


  • PSS S-BUS Clamp

    PSS S-BUS Clamp

    S-BUS-Terminal block for PSS-battery backer.

    Core element of the S-BUS system is the cable terminal block.
    An S_BUS servo can be installed at any convenient point along the length of the cable.
    Simply feed the cable between the upper and lower halves of the terminal block, press the two halves together to close the housing and lock the cable in position.
    The clamped terminal creates a reliable power and signal connection to the PSS- battery backer and receiver.
    Allocate the servo its relevant channel address, and the servo connection is done!

    SKU: F1690
    €16.70
    inc. VAT

     72HR STOCK
  • PSS S-BUS Clamp with PWM adaptor

    PSS S-BUS Clamp with PWM adaptor

    S-BUS-Terminal block with PWM-converter for PSS-battery backer.

    This S-BUS terminal block serves to connect normal analogue- and also digital servos with PWM control. The terminal block has an additional printed circuit board which converts the S-BUS signal to a PWM one.
    Hence a standard servo can be connected at any required point along the BUS cable. The PWM adapter neds to be configured with the channel address with this connection and the servo connection is done.
    The channel allocation is made with the handy S-BUS programmer SBC-1.

    SKU: F1691
    €39.00
    inc. VAT

     72HR STOCK
  • PSS Switch 30 cm

    PSS Switch 30 cm

    Creates an on/off signal for the electronic switch in the PSS battery backer and switches no power. SWitch procedure by plugging in and removing a gold plug.
    Complete with fibreglass blind and fixing screws.

    Weight: 21g
    Dimensions: 46 x 26 x 19 mm
    Lead length 30 cm
    SKU: RobbeF1665
    €27.00
    inc. VAT

  • PWM-S.BUS Converter SBE-1

    PWM-S.BUS Converter SBE-1

    The SBE-1 unit is a converter which converts the PWM signals in a normal receiver S.BUS signal.

    This makes it possible S.BUS devices, such as the gyro CGY 750, etc., which have only one S.BUS input to connect to existing receiver with PWM output.
    Up to 10 PWM channels into a S.BUS signal to be converted.

    Specifications
    Weight: 15g Dimensions: 23.5 x 33.5 x 9.5 mm cell count: 4 - 5 NC / NiMH o 2S LiFe / Lilo / LiPo
    SKU: F1711
    €75.00
    inc. VAT

     72HR STOCK
  • S-BUS - Futaba adapter plug

    S-BUS - Futaba adapter plug

    Adapter lead from USB-Adapter CIU2 to S-BUS wing plug connection.

    To address and program the wing-mounted S-BUS servos.

    SKU: F1694
    €9.20
    inc. VAT

     72HR STOCK
  • S-BUS - Futaba adapter socket

    S-BUS - Futaba adapter socket

    Adapter lead from USB-Adapter CIU2 to S-BUS wing plug connection.

    To address and program the wing-mounted S-BUS servos.

    SKU: F1693
    €9.20
    inc. VAT

     72HR STOCK
  • S-BUS Cable 150cm, 1mm

    S-BUS Cable 150cm, 1mm

    Sturdy, 3 x 1mm² thick S-BUS-ribbon cable connector lead with heavy duty gold 3 pole plug. Highly flexible with a lighweight, thin-wall thickness insulation.
    For the installation of S-BUS-wiring in fuselage or wings. The plug connection is made in output A or B of the battery backer., PSS 2018.
    The polarised plug has a lock, which ensures a reliable contact, but is also easily released.
    To connect servos and other peripheral devices, the S-BUS-terminal blocks with or without a PWM-Adapter are necessary (F 1690 or F 1691).

    SKU: F1681
    €9.90
    inc. VAT

     72HR STOCK
  • S-BUS Cable 4xPWM

    S-BUS Cable 4xPWM

    Allow the fitting of the new S-BUS system to existing models and servos. To connect between 2-4 wing servos to an S-BUS output. Converts the signal for each separate output from S-BUS to PWM. Each servo is addressable by the adapter, the outputs can have the same or different channel numbers
    The channel number allocation is made with the S-BUS Programmer SBC-1 (Nr. F1696) and no PC required.

    3-pole gold-conatact plug with lock
    Wire cross-sectional area 1mm²
    Lead length 50 cm

    SKU: F1680
    €49.90
    inc. VAT

     72HR STOCK
  • S-BUS HUB-Kabel 1->3, 30 cm

    S-BUS HUB-Kabel 1->3, 30 cm

    HUB-lead to extend and distribute S-BUS-Servo connections. Extends the connection from 1 to 3 Servos.
    Length 30 cm

    SKU: F1697
    €19.00
    inc. VAT

     72HR STOCK
  • S-BUS HUB-Kabel 1-3, 100 cm

    S-BUS HUB-Kabel 1-3, 100 cm

    HUB-lead to extend and distribute S-BUS-Servo connections. Extends the connection from 1 to 3 Servos.
    Length 100 cm

    SKU: F1698
    €17.00
    inc. VAT

     72HR STOCK
  • S-BUS Programmer SBC-1

    S-BUS Programmer SBC-1

    Handy programmer to allocate the S-BUS channel numbers to S-BUS servos or S-BUS PWM adapters.

    SKU: F1696
    €32.00
    inc. VAT

     LOW STOCK
  • S-BUS Servo S3171SB

    S-BUS Servo S3171SB

    -BUS nano-size digital servo with the sensational torque of 46 Ncm from a servo only 10.8 mm wide.

    The robust 5-level gearbox is made with 4 metal gearwheels, where 2 widely separated ball bearings protect the output gearwheel from radial forces. Although designed for 4-cell operation the servo can also be used with BEC systems, and with up to 6 Volts supplied by converters and battery backers. Ideal as a wing servo, even for sailplanes or competition model aircraft as well as mini or micro helicopters.
    Programmable!

    Specification:
    Dimensions: 30 x 10,8 x 29 mm mm
    Operating voltage: 4,8Volt /6Volt Volts
    Nominal voltage: 4.80 Volts Nominal voltage: 6.00 Volts
    Torque: 37.00 Ncm Torque: 46.00 Ncm
    Transit speed: 0.19 Sec/45° Transit speed: 0.15 Sec/45°
    Holding power: 93.00 Ncm Holding power: 115.00 Ncm
    SKU: F1624
    €44.80
    inc. VAT

     72HR STOCK
  • S-BUS Servo S9070SB

    S-BUS Servo S9070SB

    Programmable S-BUS digital universal servo operating voltage

    Fast and powerful universal digital servo with double ball-raced metalgear Low profile, only 23 mm high. Appropriated for the operation with 2 LiPo-cells.
    Programmable!

    Specification:
    Dimensions: 35,9 x 19,5 x 24,9 mm mm
    Operating voltage: 4,8-7,4 Volt Volts
    Nominal voltage: 4.80 Volts Nominal voltage: 6.00 Volts
    Torque: 45.00 Ncm Torque: 55.00 Ncm
    Transit speed: 0.13 Sec/45° Transit speed: 0.11 Sec/45°
    Holding power: 112.00 Ncm Holding power: 137.00 Ncm
    SKU: F1630
    €67.00
    inc. VAT

     72HR STOCK
  • S-BUS Servo S9072SB

    S-BUS Servo S9072SB

    Powerful and fast S-BUS digital servo 20 mm standard frame size. With core-less motor and metalgear.

    Can be used in every areas where power and speed is needed at the same time. For example on 90 size helicopter swahplates or in large models and jets. Waterproofed version, double ballraced metalgear S-BUS-version of the servo S 9452

    Specification:
    Dimensions: 40 x 20 x 36,6 mm mm
    Operating voltage: 4,8-6 Volt Volts
    Nominal voltage: 4.80 Volts Nominal voltage: 6.00 Volts
    Torque: 70.00 Ncm Torque: 87.00 Ncm
    Transit speed: 0.09 Sec/45° Transit speed: 0.07 Sec/45°
    Holding power: 175.00 Ncm Holding power: 215.00 Ncm
    SKU: F1627
    €84.00
    inc. VAT

     72HR STOCK
  • S-BUS Servo-S9074SB

    S-BUS Servo-S9074SB

    The programmable S-BUS-digitalservo with colossal strength.

    The casing center piece is made from aliuminium and serves to cool the servo motor. The ideal power servo for large-scale model aircraft, Jet`s, TOC machines etc., and for any application where sheer power is required. The gearbox features twin ballraces, and utilises an indirect drive system to couple the gearbox to the special potentiometer with 6-finger wiper. Splashproof care construction makes the servo suitable to use even under extremly harsh conditions.
    Programmable!

    Specification:
    Dimensions: 40 x 20 x 36,6 mm mm
    Operating voltage: 4,8–6,0 Volt Volts
    Nominal voltage: 6.00 Volts
    Torque: 196.00 Ncm Torque: 245.00 Ncm
    Transit speed: 0.16 Sec/45° Transit speed: 0.13 Sec/45°
    Holding power: 490.00 Ncm Holding power: 600.00 Ncm
    SKU: F1628
    €118.00
    inc. VAT

     72HR STOCK
  • S-BUS Signal Inverter set

    S-BUS Signal Inverter set

    Get all channels through a single wire! This simple cable, allows you to connect an S.BUS enabled receiver to a Naze or other Flight Controllers.  It allows you to use the 3 Channel S.BUS enabled Rx or a Futaba S.BUS receiver with full-range dual antennas and make use of 14 Channels!  This, in turn, opens up Motor outputs M7-M10 on the Naze receiver headers allowing Octo configurations.

    The cable is inserted between the receiver's S.BUS output and the Naze Flight controller receiver input power+- and signal to channel 4 to inverts the S.BUS signal.

    SKU: SBUS-INV
    €8.00
    inc. VAT

     IN STOCK
  • SBE4-S-BUS expander, 4-channel

    SBE4-S-BUS expander, 4-channel

    The S-BUS expansion SBE-4 converts S-BUS channels to PWM-channels when standard - servos - and speed controllers are connected.

    It is connected to the S-BUS output of the receiver R6108SB or R6208SB and expands the 8 standard PWM-servo-ports by a further 4-channels.
    With this accessory, this very compact receiver will be expanded to an inexpensive 12-channel receiver. As standard, the outputs are pre-programmed with channels 9…12.
    Using the CIU-2 Adapter and the free PC-Link-Software, the servo outputs of the SBE-4 are freely programmable. That means:
    That the channel allocation as well as the positioning parameters (direction, neutral position, end points, speed) may all be set-up as required.

    SKU: RB8885
    €54.00
    inc. VAT

  • Wing Servo socket 50 cm

    Wing Servo socket 50 cm

    Wing socket with connections for 2 S-BUS servos.

    Wing connection socket suitable for HUB-4.1 distribution unit. The socket will be let into the wing root and screwed into position.
    High-quality, polarity protected and latching 3 pole gold plug and socket connection. Secure contact, but still easy to assemble and dissemble.

    Lead length 50 cm.

    SKU: ROB88840003
    €8.40
    inc. VAT

  • Wing socket with connections for 2

    Wing socket with connections for 2

    Wing socket with connections for 2 S-BUS servos.

    Wing connection socket suitable for HUB-4.1 distribution unit. The socket will be let into the wing root and screwed into position. High-quality, polarity protected and latching 3 pole gold plug and socket connection. Secure contact, but still easy to assemble and dissemble. Lead length 50 und 130 cm.

    SKU: ROB88840002
    €9.20
    inc. VAT


Manufacturers

Back