Robbe

Robbe
a German company, producer of Shlutter helicopters, Importer and service center for Futaba

www.Robbe.com

Products


  • TANK MILLENNIUM

    TANK MILLENNIUM

    TANK MILLENNIUM 630 CCM, no hardware
    SKU: S4809
    €19.10 €22.50
    inc. VAT

     LOW STOCK
  • TAPER COLLET 8MM

    TAPER COLLET 8MM

    TAPER COLLET 8MM

    SKU: S3176
    €8.10 €9.50
    inc. VAT

     IN STOCK
  • Teflon Tube 20X24

    Teflon Tube 20X24

    PTFE- tube connector for silencers/tuned pipes

    20mm inside diameter

    SKU: S0916
    €9.50
    inc. VAT

  • THREADED ROD M3X60

    THREADED ROD M3X60

    THREADED ROD M3X60

    SKU: S4625
    €4.30 €5.00
    inc. VAT

     LOW STOCK
  • THRUST BEARING 4MM

    THRUST BEARING 4MM

    THRUST BEARING 4MM

    SKU: S3364
    €12.70 €14.95
    inc. VAT

  • Top Equalizer 6 Cells 300

    Top Equalizer 6 Cells 300

    The Top-Equalizer 6S 300 mA is designed for equalizing (balancing) series-wired LiIo / LiPo / LiFe cells.
    The LiPo TOP Equalizer is connected between the LiPo charger and the LiPo battery.

    During the charge process the unit automatically brings the voltage of individual series-wired LiPo cells within a battery pack up to the same level. This is necessary, since the individual cells tend to be discharged to different voltages (states of charge) when in use. The Equalizer prevents overcharging or deep-discharging, which can result in permanent cell damage.

    The final charge voltage and charge current parameters are set on the battery charger. In contrast to earlier voltage controller devices, the Equalizer starts correcting the cell voltages immediately, when the charge process is initiated.

    TOP function -> permits the display of individual cell voltages on the integral screen of suitable battery chargers (e.g. Power Peak Compact and Infinity 3), or on a PC.

    Over-voltage cut-off: the device features a safety function in the form of over-voltage termination, which is triggered if the voltage of any one cell in the pack rises to 4.3 Volts (LiPo), 4.2 Volts (LiIo) or 3.9 Volts (LiFe). If used in conjunction with suitable battery chargers, the Equalizer automatically reduces the charge current when the cells reach a voltage of 4.25 V (4.15 V / 3.85 V). The battery must be connected to the TOP Equalizer using a sensor lead. robbe LiPo batteries are already fitted with the appropriate connector (JST-EHR).

    Features:

    2 ... 6 LiIo cells (3.6 V / cell), LiPo cells (3.7 V / cell) or LiFe batteries (3.3 V / cell) with a suitable LiPo charger, e.g. Power Peak Compact, Infinity 3.
    The Equalizer function can also be used separately, i.e. without a battery charger.

    Load current: 10.00 A
    Weight: 95 g

    SKU: Robbe8492
    €39.00
    inc. VAT

     LOW STOCK
  • Transmitter Outlet Charger 150

    Transmitter Outlet Charger 150

    Wall Outlet Charger TX-Rx 150/150 for Futaba radios

    Charging current : 150ma TX, and 150ma RX

    SKU: Robbe8282
    €12.00
    inc. VAT

     LOW STOCK
  • Transmitter Tray FX-30

    Transmitter Tray FX-30

    An elegant, lightweight Carbon -CFRP transmitter tray for the FX-30 transmitter.
    All transmitter controls and facilities are freely accessible, including the RF module, battery compartment, charge socket, etc. Removable neckstrap bars with bayonet clips. Supplied complete with 38 mm wide two-point neckstrap. The supplementary neck padding features Velcro fastenings, and is removable. Simple to fit using knurled-head screws.

    SKU: Robbe8491
    €116.00
    inc. VAT

  • TUNED PIPE HOLDER

    TUNED PIPE HOLDER

    TUNED PIPE HOLDER 24 MM
    SKU: S0948
    €8.90 €10.50
    inc. VAT

     IN STOCK
  • Tx LiPo charger 8.4 V / 500 mA T8/12FG

    Tx LiPo charger 8.4 V / 500 mA T8/12FG

    Tx LiPo charger 8.4 V / 500 mA T8/12FG

    Mains charger with 8,4V output and charge current of 500 mA.
    Connector plug 1,7 mm inside diameter and cable length of 1 m.

    SKU: RB8298
    €14.00
    inc. VAT

     LOW STOCK
  • Universal helicopter Multi Tool box

    Universal helicopter Multi Tool box

    Dont leave it at Home, It will be the best ever item you purchased.. Also can be very good Gift to any modeler and pilot

    Included:

    1 x Flat Head Screw Driver -Black
    1 x Phillips Head Screw Driver - Black
    1 x Hexagon Screw Driver (Tip 3.0mm) Black
    1 x Carbon Steel M2 Nut Driver (4.0mm) - Black
    1 x Carbon Steel M3 Nut Driver (5.5mm) - Black
    1 x Hexagon Screw Driver (Tip 1.5mm) - Black
    1 x Hexagon Screw Driver (Tip 2.0mm) - Black
    1 x Hexagon Screw Driver (Tip 2.5mm) - Black
    1 x Micro Helicopter Pitch Gauge
    1 x Deluxe Precision Diagonal Cutter
    1 x Deluxe Long Nose Plier/ Cutter
    1 x Curve Tip Ball Link Pliers)

    Size: 55 x 189 x 245mm
    Weight: 1kg

    SKU: RB5718
    €59.00
    inc. VAT

     LOW STOCK
  • Vario and altimeter(TEK)

    Vario and altimeter(TEK)

    Precision variometer with altitude and variometer monitoring using two separate pressure sensors

    With its small dimensions and a weight of only 5.5 g is is likely that the robbe TEK precision vario and altimeter is currently the world's smallest, lightest and most accurate sensor (with dual TEK sensor). The individual robbe-Futaba sensor ID automatically configures the sequence and display unit when the sensor is registered (to the transmitter or the Telemetry-Box).
    Features of the vario-altimeter sensor:

  • High sensitivity of 2 cm/s makes it possible to exploit very weak thermal lift. The system indicates even the slightest sign of the model climbing.
  • Specification


    Dimensions: approx. 37.5 x 22.5 x 9.3 mm
    Weight: approx. 6.5 g
    Operating voltage: 3.6 ... 8.4 V
    Current drain: approx. 5 mA

  • The TEK socket makes it possible to compensate for "stick-generated thermals". The result is that speed changes have hardly any effect on the vario sound and speech output.
  • The second supplementary pressure sensor provides accurate altitude monitoring, in spite of the variometer's TEK compensation, which produces a further improvement in sensitivity.
  • This variometer is naturally height-compensated (a 1 mBar change of pressure at sea-level corresponds to a different rate of climb at an altitude of 3000 m )
  • Pressure is converted in accordance with standard ICAO atmosphere with an accuracy of 1 m
  • The TEK vario / altimeter is particularly good at rejecting interference from 2.4 GHz telemetry transmitters.
  • Update facility via USB, i.e. software updates and future developments can be installed by the user
  • Pressure element mounted on a ceramic substrate for extremely low pressure sensor drift due to temperature and protracted usage.
  • Vario measurement range: -300 m/s …+300 m/s
  • Vario resolution: = 2 cm/s
  • Altitude measurement: -1000 m ... +9000 m
  • Altitude resolution: 1 m
  • SKU: F1672
    €219.00
    inc. VAT

     72HR STOCK
  • Washer  2MM 20PCS

    Washer 2MM 20PCS

    WASHER  2MM STEEL 20PCS

    SKU: S0000
    €2.50 €2.95
    inc. VAT

     IN STOCK
  • WASHER  3MM

    WASHER 3MM

    WASHER-U 3MM 20PCS
    SKU: S0007
    €2.50 €2.95
    inc. VAT

     IN STOCK
  • WASHER  4MM

    WASHER 4MM

    WASHER 4MM 4PCS
    SKU: S0003
    €3.00
    inc. VAT

     IN STOCK
  • WASHER  6MM

    WASHER 6MM

    WASHER 6MM  10PCS
    SKU: S0005
    €3.70 €4.30
    inc. VAT

     IN STOCK
  • WASHER 3MM

    WASHER 3MM

    WASHER-U 3MM  20PCS
    SKU: S0001
    €2.50 €2.95
    inc. VAT

     LOW STOCK
  • WASHER 8X13X0.5

    WASHER 8X13X0.5

    WASHER 8X13X0,5 2PCS

    SKU: S1585
    €1.70 €2.00
    inc. VAT

     IN STOCK
  • WASHER-U 4MM

    WASHER-U 4MM

    WASHER-U 4MM 20PCS
    SKU: S0002
    €2.50 €2.95
    inc. VAT

     IN STOCK
  • Wing Servo socket 50 cm

    Wing Servo socket 50 cm

    Wing socket with connections for 2 S-BUS servos.

    Wing connection socket suitable for HUB-4.1 distribution unit. The socket will be let into the wing root and screwed into position.
    High-quality, polarity protected and latching 3 pole gold plug and socket connection. Secure contact, but still easy to assemble and dissemble.

    Lead length 50 cm.

    SKU: ROB88840003
    €8.40
    inc. VAT

  • Wing socket with connections for 2

    Wing socket with connections for 2

    Wing socket with connections for 2 S-BUS servos.

    Wing connection socket suitable for HUB-4.1 distribution unit. The socket will be let into the wing root and screwed into position. High-quality, polarity protected and latching 3 pole gold plug and socket connection. Secure contact, but still easy to assemble and dissemble. Lead length 50 und 130 cm.

    SKU: ROB88840002
    €9.20
    inc. VAT


Manufacturers