Robbe

Robbe
a German company, producer of Shlutter helicopters, Importer and service center for Futaba

www.Robbe.com

Products


  •  Nine Eagles Galaxy Visitor 6 - Main gear set (4 pcs)

    Nine Eagles Galaxy Visitor 6 - Main gear set (4 pcs)

    Nine Eagles Galaxy Visitor 6 - Main gear set (4 pcs)

    SKU: NE253203
    €5.90
    inc. VAT

     LOW STOCK
  •  PITCH COMPENSATOR for 10mm shaft

    PITCH COMPENSATOR for 10mm shaft

    PITCH COMPENSATOR HUB 10mm shaft

    SKU: S4665
    €11.00
    inc. VAT

     IN STOCK
  • 6 VOLT LIMITER LIPO

    6 VOLT LIMITER LIPO

    The robbe 6 Volt Limiter derives a stabilised voltage of 5.7 Volts from a 5-cell NC / NiMH battery or two Lithium cells.
    The maximum continuous load is 5 Amps, but the peak is significantly higher. A constant voltage supply offers the advantage that the servos always deliver consistent power and transit speed regardless of battery voltage. With this limiter it is also possible to use servos which are only designed for use with four NC / NiMH cells.Also suitable for stabilising the voltage of two Li-Po cells (7.4 Volts).

    In this case the maximum continuous load is reduced to around 3.0 Amps since the unit has to dissipate more waste power. For simple applications one cable to the standard switch harness is all you need. For applications with higher current drain we recommend that you use two cables and a switch harness designed for higher load currents.

    For example, the 5 A switch harness, No. 8024, or the Safety Switch, No. 8498, which features secure electronic contacts. In this case the second cable is connected to any vacant channel at the receiver.Note: If you wish to connect a second cable it will be necessary to attach a second lead to the receiver battery.
    Two separate batteries must not be used, as this would bridge the input, causing the batteries to be wired in parallel.

    SKU: Robbe-8476
    €19.00
    inc. VAT

  • Air Beaver ARF

    Air Beaver ARF

    Just like its big brother, the robbe Air Beaver also has exceptional good mannered flight characteristics. The intermediate beginner pilots will also quickly become confident with this model. Added to by its distinctive silhouette in flight and the non critical take-off and landing characteristics in windy conditions. The servo-operated landing flaps make slow flight an absolute joy.
    Our ARF model needs only a receiver and battery fitting before the first flight. All the other electronics such as speed controller, servos and motor are included in the kit contents. These features, the level of equipment and naturally the comprehensive spare parts back-up make the Air Beaver a terrific model for the intermediate pilot.

    Fuselage, wings and tailplane fully finished in EPO foam.
    All foam parts fully painted with applied decals
    Fixing points for optional float set
    5 servos installed and wired.
    Brushless-Outrunner electric motor and controller installed and wired.
    Spinner, 2-blade propeller and prop driver.
    Plastic dummy engine cowling and other detailed parts
    2 leg main undercarriage and steerable tail-wheel.
    Aerodynamic section wing struts
    Working LED navigation and landing light installed and wired.
    Working flaps installed with servo fitted.
    Self-closing battery compartment with vented plastic cover.
    Comprehensive, illustrated final assembly instructions.

    Specification:

    Wing loading approx: 42
    Length approx: 960
    Total surface area approx: 28
    All-up weight approx: 1200

     

    SKU: RB-2569
    €169.00
    inc. VAT

  • Air Trainer 140

    Air Trainer 140

    The aerobatic trainer

    Fit the propeller and wings, and connect the receiver and battery: that‘s all there is to it, and the Air-Trainer is ready for its first flight without any need for glue.
    With its highly cambered wing airfoil, low wing loading (thanks to the hollow wing construction with stiffening ribs), and any amount of power, the model is easy to fly and capable of all aerobatic manoeuvres including torque-rolls.
    The Air-Trainer is highly crash-resistant, and is also easy to repair if damaged.
    A further highlight is the pair of LED lights mounted at the wingtips.
    The Air Trainer 140 is a great choice for the advanced beginner who already has some basic experience with aileron-equipped models.

    Set contents

    • EPO foam fuselage, wings and tail
    • All foam components painted or with decals applied
    • All servos (robbe E-Coline series) installed and wired
    • Robbe E-Coline series BL outrunner electric motor and speed controller (40A) installed and wired
    • Spinner, propeller and propeller driver
    • Robust undercarriage with large wheels
    • Two working LED lights installed and wired
    • Comprehensive illustrated final assembly instructions

    Specification:

    • Wingspan approx. 1400 mm
    • Length approx. 1130 mm
    • Total surface area approx. 36,8 dm2
    • Wing loading approx. 41,6 g/dm2
    • All-up weight approx. 1550 g
    RC functions

    • Elevator, Rudder, Aileron, Motor control
    SKU: RB-2581
    €229.00
    inc. VAT

  • ALU SPACER 11 LONG (2pcs)

    ALU SPACER 11 LONG (2pcs)

    ALU SPACER 11 LONG (2pcs)

    SKU: S4659
    €5.80 €6.85
    inc. VAT

     LOW STOCK
  • ALU-FLAT GEAR HUB

    ALU-FLAT GEAR HUB

    ALU-FLAT GEAR HUB

    SKU: S4616
    €28.50 €33.50
    inc. VAT

     IN STOCK
  • Aluminum damper insert

    Aluminum damper insert

    Aluminum damper insert , 2 PCS for Robbe Millenium

    (those parts were disassembled from the head, so very slight cosmetic scratches on them)



    SKU: S46821
    €19.00
    inc. VAT

     LOW STOCK
  • ANGLE BRACKET LEFT

    ANGLE BRACKET LEFT

    ANGLE BRACKET L.AL BLACK 1PCS

    SKU: S48192
    €13.30 €15.60
    inc. VAT

     IN STOCK
    NEW
  • ANGLE BRACKET RIGHT

    ANGLE BRACKET RIGHT

    ANGLE BRACKET R.AL BLACK 1PCS

    SKU: S48182
    €13.30
    inc. VAT

     IN STOCK
    NEW
  • APC-Propeller 10x 3.8 Slow Fly

    APC-Propeller 10x 3.8 Slow Fly

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: APC10X3.8sf
    €4.00
    inc. VAT

     IN STOCK
  • APC-Propeller 10x 3.8SF PUSHER

    APC-Propeller 10x 3.8SF PUSHER

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: APC10X3.8SFP
    €5.60
    inc. VAT

     IN STOCK
  • APC-Propeller 10X5 electro

    APC-Propeller 10X5 electro

    APC props are manufactured using a pultrusion process.
    This method causes the fiberglass "fibers" to be oriented axially in 1/2" long pellets, allowing for a higher fiber (60%) to resin (nylon binder) density. Providing substantially higher strength and stiffness than glass filled nylon.
    The additional stiffness is beneficial to control of vibration resonance response. The higher strength allows the use of thinner cross-sections, beneficial to weight and aerodynamic efficiency.

    Competition proven. Dark gray composite material.

    Diameter x Pitch in inches:10X 5, special for electric planes.

    SKU: APC10X5E
    €5.00
    inc. VAT

     IN STOCK
  • APC-Propeller 10x6 Slow fly

    APC-Propeller 10x6 Slow fly

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: 77851006
    €4.20
    inc. VAT

     IN STOCK
  • APC-Propeller 10x7 slow fly

    APC-Propeller 10x7 slow fly

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: 77881007
    €4.50
    inc. VAT

  • APC-Propeller 10X7 Slow Fly

    APC-Propeller 10X7 Slow Fly

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: APC10X7SF
    €4.00
    inc. VAT

     LOW STOCK
  • APC-Propeller 11.5X6 Sport

    APC-Propeller 11.5X6 Sport

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    size 11.5x6 for Glow and Electric

    SKU: APC11.5X6
    €4.90
    inc. VAT

     LOW STOCK
  • APC-Propeller 11X4 Slow Fly

    APC-Propeller 11X4 Slow Fly

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: 77881104
    €4.90
    inc. VAT

     LOW STOCK
  • APC-Propeller 11X4.7 Slow Fly

    APC-Propeller 11X4.7 Slow Fly

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    SKU: APC11X4.7SF
    €5.00
    inc. VAT

     LOW STOCK
  • APC-Propeller 12.25X3.75 Sport

    APC-Propeller 12.25X3.75 Sport

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    Diameter x Pitch in inches: 12.3x3.8

    SKU: 77851203
    €7.50
    inc. VAT

     LOW STOCK
  • APC-Propeller 13x6.5 Electric

    APC-Propeller 13x6.5 Electric

    Precision for ultimate power
    APC propellers are manufactured using the latest CNC-machined metal moulds. The blade airfoils are carefully selected with low current drain (where applicable), excellent efficiency, and lowest possible weight as top priority, combined with ample strength. This is only
    possible through the use of a special glass fibre reinforced plastic and a sophisticated computer design program.
    You too can benefit from these advantages - just move up to APC propellers!

    size 13x6.5 for Glow and Electric

    SKU: 77841306
    €7.50
    inc. VAT

  • APC-Propeller 9x6 electro

    APC-Propeller 9x6 electro

    APC props are manufactured using a pultrusion process.
    This method causes the fiberglass "fibers" to be oriented axially in 1/2" long pellets, allowing for a higher fiber (60%) to resin (nylon binder) density. Providing substantially higher strength and stiffness than glass filled nylon.
    The additional stiffness is beneficial to control of vibration resonance response. The higher strength allows the use of thinner cross-sections, beneficial to weight and aerodynamic efficiency.

    Competition proven. Dark gray composite material.

    Diameter x Pitch in inches:9x6, special for electric planes.

    SKU: APC9X6E
    €4.00
    inc. VAT

     LOW STOCK
  • Arcus V-Tail EDF 1400

    Arcus V-Tail EDF 1400

    Set contents

    • Robust EPO foam fuselage, wings and tail, with decals applied
    • Factory-trimmed canopy
    • Small hardware items for control linkages and servo covers
    • Factory-installed 50 mm Ø fan unit with brushless motor and speed controller from the robbe E-COLINE series
    • 3 factory-installed robbe E-COLINE 8 g servos
    • Illustrated multi-lingual assembly instructions

    Specification:

    • Wingspan approx. 1400 mm
    • Length approx. 770 mm
    • Total surface area approx. 15 dm2
    • Wing loading approx. 33,3 g/dm2
    • All-up weight approx. 500 g
    • RC functions
    • Elevator, Aileron, Motor control


    SKU: RB-2592
    €149.99 €159.00
    inc. VAT

  • Arcus V-Tail Prop 1400

    Arcus V-Tail Prop 1400

    Compact powered glider suitable for beginners The V-Tail Prop is the latest addition to the
    robbe Arcus family, and is an eye-catcher in several ways - not just due to its unusual looks.

    Its above-average performance in the air, and its suitability for any pilot from the relatively inexperienced pilot with some experience of aileron models right up to the advanced pilot, are ample proof of its tremendous versatility.
    With its compact dimensions, the Arcus V-Tail Prop is the ideal „evening flyer“, as it is easy to transport in any car, and can be ready for flying the moment you reach the
    club patch.
    The model can also be fitted with an optional rudder servo.


    Set contents

    • Robust EPO foam fuselage, wings and tail with decals applied
    • Factory-trimmed canopy
    • Small hardware items for control linkages and servo covers
    • Propeller and spinner already fitted
    • Brushless motor and speed controller from
    • the robbe E-COLINE series
    • 3 factory-installed robbe E-COLINE 8 g servos
    • Illustrated multi-lingual assembly instructions No. 2593

    Specification:

    • Wingspan approx. 1400 mm
    • Length approx. 770 mm
    • Total surface area approx. 15 dm2
    • Wing loading approx. 30 g/dm2
    • All-up weight approx. 450 g
    • RC functions
    • Elevator, Aileron, Motor control


    SKU: RB-2593
    €149.99 €159.00
    inc. VAT


Manufacturers