Europe based Mega-Store of RC Helicopters, Drones, Planes

eRCMarket is a Belgium based superstore for all your remote control helicopters, drones, cars and airplane needs. We also stock a huge range of parts, tools and accessories. With over 40 years experience in R/C, UAV and UAS, we have been serving customers all over the world for over 20 years.

New Arrivals

CUAV X7+ Flight Controller Autopilot For PX4&APM Drone UAV

CUAV X7+ Flight Controller Autopilot For PX4&APM Drone UAV

X7+ autopilot uses STM32H743 series processors CPU, Cortex-M7 core (with double precision Floating-Point Unit). It makes operating frequency increase to 480Mhz, 2MB Flash,1MB RAM,Meet the higher computing needs of flight controllers Compared with the STM32F7 product line, the dynamic power consumption efficiency is doubled.

The sensor is one of the important indicators to evaluate the flight controller. This time, we have added the ICM-42688-P sensor. Compared with the traditional consumer IMU, the noise figure of ICM-42688-P is reduced by 40%, and the temperature stability is improved 2 times, so as to ensure the highest accuracy measurement in the case of temperature changes.

Sensor Redundancy Design

Built-in three sets of accelerometers and gyroscopes, the flight controller monitors the data of multiple sensors in real time, and executes redundant switching immediately in case of failure to improve flight safety and stability.

Temperature Compensation

System

The built-in high-precision sensor temperature compensation system makes the sensor work at a constant temperature, ensuring that the sensor can operate stably with high precision and sensitivity in high and low temperature environments.

CORE Separate Design

The X7+ flight controller integrates the main MCU and IMU into the CORE module and can be sold separately. Users can design the baseboard according to the UAV structure to meet the individual needs of users, or purchase our CAN PDB baseboard for use. The X7+ CORE interface is compatible with X7, X7 Pro, and V5+ flight controller CORE.

Better CUAV Patented Shock Absorption System

After dozens of iterations, hundreds of shock-absorbing materials have been tested and verified, computer model analysis and thousands of flight tests, so improve the shock absorption to a further level

Standard Pack Digital

Power Module

Standard package include UAVCAN protocol digital power detection module, using CUAV independent R&D ITT algorithm, accurate measurement of UAV real-time voltage and current, making flight time estimation more reliable.

Firmware:

Note:X7+ flight controller is compatible with ArduPilot 4.10/ PX4 1.12.3 or higher firmware.

Copter/Plane,

Support all models: Copter/Plane/ Helicopter/VTOL/unmanned vehicle/ Rover, etc.

Specifications

Main FMU Processor: STM32H743

On-board sensors:

Accelerometer/Gyroscope: ICM-42688-P(X7:BMI088)

Accelerometer/Gyroscope: ICM-20689

Accelerometer/Gyroscope: ICM-20689(X7:ICM-20649)

Magnetometer: RM3100

Barometer: MS5611*2

Interfaces:

14 PWM outputs (12 supports Dshot)

Support multiple RC inputs (SBUs/CPPM/DSM)

Analogue/ PWM RSSI input

2 GPS ports(GPS and UART4 ports)

6 i2c buses(Four i2c dedicated ports)

2 CAN bus ports

2 Power ports(Power A is common adc interface, Power C is uavcan battery interface)

1 ADC intput

1 USB ports

Power System:

Power: 4.5~5.4V

USB Input: 4.75~5.25V

Servo Rail Input: 0~10V

Weight and Dimensions:

Weight: 101 g

Other Characteristics:

Operating temperature: -20 ~ 85°c

Three imus

Supports temperature compensation

Internal shock absorption

x7 plus pinouts

CUAV X7+ Features:

1–Built-in shock absorption

2–3 sets of Imus support intelligent failover

3–Support temperature compensation

4–Support CAN ammeter

5–Modular design, support custom baseboard

€399.00

Inc. VAT
Quantity
Kavan Radio Transmitter V20 - Black, 24-channel ACCST Hall sensors

Kavan Radio Transmitter V20 - Black, 24-channel ACCST Hall sensors

Advanced 24-channel RC set Twin 2.4GHz/ACCST D16/ACCESS. Ergonomic robust body, precision gimbals with Hall sensors. Full telemetry support, large color touch screen with intuitive user interface. ETHOSâ„¢ operating system. Extensive range of functions and mixes for all types of RC models. KAVAN servo programming. Support for telemetry receivers with classic PWM and S.BUS outputs.

Exactly according to preference

The rigorously CNC-machined aluminum gimbals are mounted on 10 ball bearings. Hall sensors instead of conventional potentiometers sense the movement of the sticks. This makes the control more precise and reliable. You can also customize the controllers to your own preferences. Easily adjust the length of the sticks, rotate the gimbals up to 8°, and limit the range of stick travel to 45° to 60°.

Comfortable and stylish

Looks matter. Comfort matters even more. The gimbals are closer to the edges of the transmitter body for a comfortable and secure grip. Both handheld and when using the. Switches, buttons, dials and trims are always within reach. So you don't have to take your eyes off your model for a second. But the stylish and vigorous exterior of the transmitter tempts you to do so.

Don't get jammed

The 2.4GHz simultaneous dual-frequency transmission system communicates simultaneously with both the receiver and the RF module. The two built-in 2.4GHz antennas have greater omnidirectional coverage for the transmitted signal compared to a single antenna. This makes the transmission uninterrupted and has a rapid response time of under 4 ms. Data (including telemetry) will flow safely to you over several kilometers.

Touch the colors

The large color touchscreen has a resolution of 800Ă—480 px on a 4.3" diagonal. It displays the ETHOSâ„¢ operating system environment. With adjustable display brightness, you won't get lost in the dark or directly under the sun. Intuitively, clearly, and most importantly, conveniently set up or display everything from basic telemetry to advanced mixes and curves directly in the transmitter. You can even choose the colour scheme or turn on dark mode and read everything in English or many other languages

Connectivity for an easier life

Use the USB serial port for data transfer, battery charging, and even if you want to fly the simulator. And because it's USB-C, you always plug it in on the first try. Of course, there's also a trainer port, headphone jack or microSD card slot. Besides audio or voice alerts, you can also activate vibration feedback.

Plugging in a single connector is more elegant than searching for identical (and charged) batteries. The included 2S LiPo 4000mAh battery provides 6.5–8.4V power. It can be safely charged with a USB-C cable thanks to the built-in balancer. No need to remove it from the case. The available timer and warning signals take care of early warning of running out of power.

€599.00

Inc. VAT
Quantity
Kavan Radio Transmitter V20 - Blue, 24-channel ACCST Hall sensors

Kavan Radio Transmitter V20 - Blue, 24-channel ACCST Hall sensors

Advanced 24-channel RC set Twin 2.4GHz/ACCST D16/ACCESS. Ergonomic robust body, precision gimbals with Hall sensors. Full telemetry support, large color touch screen with intuitive user interface. ETHOSâ„¢ operating system. Extensive range of functions and mixes for all types of RC models. KAVAN servo programming. Support for telemetry receivers with classic PWM and S.BUS outputs.

Exactly according to preference

The rigorously CNC-machined aluminum gimbals are mounted on 10 ball bearings. Hall sensors instead of conventional potentiometers sense the movement of the sticks. This makes the control more precise and reliable. You can also customize the controllers to your own preferences. Easily adjust the length of the sticks, rotate the gimbals up to 8°, and limit the range of stick travel to 45° to 60°.

Comfortable and stylish

Looks matter. Comfort matters even more. The gimbals are closer to the edges of the transmitter body for a comfortable and secure grip. Both handheld and when using the. Switches, buttons, dials and trims are always within reach. So you don't have to take your eyes off your model for a second. But the stylish and vigorous exterior of the transmitter tempts you to do so.

Don't get jammed

The 2.4GHz simultaneous dual-frequency transmission system communicates simultaneously with both the receiver and the RF module. The two built-in 2.4GHz antennas have greater omnidirectional coverage for the transmitted signal compared to a single antenna. This makes the transmission uninterrupted and has a rapid response time of under 4 ms. Data (including telemetry) will flow safely to you over several kilometers.

Touch the colors

The large color touchscreen has a resolution of 800Ă—480 px on a 4.3" diagonal. It displays the ETHOSâ„¢ operating system environment. With adjustable display brightness, you won't get lost in the dark or directly under the sun. Intuitively, clearly, and most importantly, conveniently set up or display everything from basic telemetry to advanced mixes and curves directly in the transmitter. You can even choose the colour scheme or turn on dark mode and read everything in English or many other languages

Connectivity for an easier life

Use the USB serial port for data transfer, battery charging, and even if you want to fly the simulator. And because it's USB-C, you always plug it in on the first try. Of course, there's also a trainer port, headphone jack or microSD card slot. Besides audio or voice alerts, you can also activate vibration feedback.

Plugging in a single connector is more elegant than searching for identical (and charged) batteries. The included 2S LiPo 4000mAh battery provides 6.5–8.4V power. It can be safely charged with a USB-C cable thanks to the built-in balancer. No need to remove it from the case. The available timer and warning signals take care of early warning of running out of power.

€599.00

Inc. VAT
Quantity
CUAV Skye DroneCAN Air Speed Sensor Module (Heated Pitot)

CUAV Skye DroneCAN Air Speed Sensor Module (Heated Pitot)

The first in the industry to integrate pitot tube, airspeed sensor, temperature and humidity sensor, ARM M4 processor, and dual temperature control system into one structure, and has rainproof performance. 

The pitot tube integrates a high-power 35W heating system, which automatically heats according to the ambient temperature and humidity, avoiding data errors caused by pitot tubes freezing or rain blocking, and greatly improving the reliability of UAV operations.

Features

  • Dual Temperature Control System
  • Intelligent Deicing
  • Rainproof Structure
  • DroneCAN Protocol

€194.00

Inc. VAT
Quantity
CUAV CAN PMU UAV power management module 62v 110A

CUAV CAN PMU UAV power management module 62v 110A

CAN PMU is a UAV power management unit module with built-in STM32F4 processor and running CUAV ITT algorithm. It can accurately measure UAV voltage and current in real time. It can support 6-62V voltage and 110A current at maximum, and can output 5.4V 8A. The flight controller is powered by CAN bus communication and supports the standard UAV CAN protocol.

Each PMU unit is factory calibrated to ensure good consistency and high accuracy

Features:

  •  Input voltage 6- 62v (2 - 15S LiPo)
  • Continuous current 110A
  • Compatible with CUAV, APM, Pixhawk, Ardupilot.
  • Power Out: 5.4v @ 5A max 8A
  • UAVCAN Protocol

€129.00

Inc. VAT
Quantity
CUAV X7+ Pro Industrial ADIS16470 Autopilot ARM STM32H7

CUAV X7+ Pro Industrial ADIS16470 Autopilot ARM STM32H7

X7+ Pro is an advanced autopilot independently designed by CUAV. It uses a higher-performance STM32H7 processor and integrates industrial-grade sensors and ultra-low temperature drift sensors. Compared with the previous flight controller,it has better performance and more reliability. This board can run ArduPilot firmware perfectly. X7+ Pro is ideal for industrial drones.

Faster than ever

CUAV X7+ Pro autopilot use STM32H7 series processors, CPU operating frequency increased to 480Mhz, storage 1024K, FLASH 2048K, has a faster processor and larger storage, and uses 512K EEPROM, can expand waypoints to 2048, Bring more imagination to flight applications

Built-in shock absorption design

CUAV X7+ Pro flight controllers have a built-in and reliable CUAV patented shock absorption system, making them fearless of flight jitter!

Adapt to harsh environment

CUAV X7+ Pro autopilot adopts numerous car-level chips and has a built-in high-precision sensor temperature compensation system, which makes the sensor work at a constant temperature to ensure that the sensor can operate with high accuracy and high sensitivity in high and low temperature environments.

Always stable

Invensense + Bosch + ADI + TE series sensors are used, which have lower noise and stronger anti-shock and vibration performance. With the industrial-grade compass RM3100, the flight stability and anti-interference performance have brought a qualitative improvement

Difference between X7+ Pro and X7+?

X7+ Pro replaces the ICM-20689 chip on the X7+ with a high-end ADI16470 chip. Because of its excellent gyro and acceleration drift performance, it has been used in some cutting-edge aerospace projects in the past. This time, we introduced it into the open source flight control, which is integrated into the IMU with triple redundancy and exerts excellent performance

For the regular version, please check CUAV X7+ Flight Controller

ADIS16470 sensor!

X7+ Pro and X7+ are only different from sensors: X7+ pro uses ADI16470 chip instead of ICM-20689 And the front logo has more Pro words, other appearance and size are the same as X7+.

Dual platform compatible

CUAV X7+ Pro Supports the current mainstream PX4 (PX4 is being adapted) and Ardupilot two open source platform firmware to meet the needs of different users.

CUAV X7 Pro Flight Controller quality

CUAV deeply cooperated with the APM & PX4 team to complete the hardware design and software adaptation of the CUAV X7 series, and was produced and tested by the CUAV smart factory. Each autopilot was used for independent I / O through the CUAV AATS system Connectivity and sensor stability test to ensure the stability and reliability of the autopilot.

Other characteristics

Internal shock absorption

Modular design, can be DIY carrier board

Support USB_HS, download logs faster

Support more dshot output

Support IMU heating, make the sensor work better

Dedicated uavcan battery port

3 sets of IMU sensors

High-precision industrial sensor(ADIS16470+RM3100)

€889.00

Inc. VAT
Quantity
Receiver KAVAN R8 VARIO 2.4GHz Dual Freq 24ch S.bus #KAV18.10008V

Receiver KAVAN R8 VARIO 2.4GHz Dual Freq 24ch S.bus #KAV18.10008V

Advanced 8-channel 2.4GHz simultaneous dual-frequency Twin 2.4GHz telemetry receiver. It has 8 high-precision PWM channels and 16 or 24-channel modes via S.BUS. Two detachable antennas with IPEX4 connector provide full signal strength over a range of up to tens of kilometers. It is especially ideal for gliders, but you can also use it for other various models. With redundancy support, it can be connected as a primary receiver via S.BUS. With the Twin 2.4GHz protocol, both receivers work fully simultaneously in this setup. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices, providing bidirectional data transmission via a single cable.

It features advanced interference suppression for reliable, stable signal transmission across the entire range. Smart transmission system matching speeds up pairing. The black box function stores essential flight data. Receiver operating statuses are indicated by an LED indicator. Smart pairing allows firmware updates wireless.

It is equipped with a variometer that provides more accurate and faster measurement and transmission of altitude and vertical speed data. It also allows quick audio feedback from the variometer to the Twin 2.4GHz transmitters.

Features:

  • Increased protection against RF interference and more stable RF transmission
  • Simultaneous Twin 2.4GHz dual frequency transmission system with smart pairing
  • Black box function
  • High maximum operating range
  • Wireless firmware updates (OTA)
  • 8 high-precision PWM channels
  • S.BUS output port (16/24 channel mode)
  • S.BUS input port (with support for redundant connection of 2 receivers)
  • F.BUS / S.Port

Technical specifications:

  • Frequency: simultaneous dual 2.4 GHz
  • Dimensions: 54Ă—20Ă—10 mm (L*W*H)
  • Weight: 9.8 g
  • Operating voltage: 3.5–10 V (supply voltage min. 2.8 V).
  • Operating current: 80 mA at 5 V
  • Vario - vertical speed measurement range: ±10 m/s
  • Vario - altimeter range and resolution: -700 m to 10,000 m, 0.1 m
  • External voltage measurement range via AIN2: 0–35 V
  • Antenna connector: IPEX4
  • Compatibility: 2.4 GHz dual-frequency simultaneous transmission system

€59.90

Inc. VAT
Quantity
Receiver KAVAN R8 2.4GHz Dual Freq 24ch S.bus  #KAV18.10008

Receiver KAVAN R8 2.4GHz Dual Freq 24ch S.bus #KAV18.10008

Advanced 8-channel 2.4GHz simultaneous dual-frequency Twin 2.4GHz telemetry receiver. It has 8 high-precision PWM channels and 16 or 24-channel modes via S.BUS. Two detachable antennas with IPEX4 connector provide full signal strength over a range of up to tens of kilometers. It is especially ideal for gliders, but you can also use it for other various models. With redundancy support, it can be connected as a primary receiver via S.BUS. With the Twin 2.4GHz protocol, both receivers work fully simultaneously in this setup. Thanks to the F.BUS connection option, you can also pair it quickly and easily to several different telemetry devices, providing bidirectional data transmission via a single cable.

It features advanced interference suppression for reliable, stable signal transmission across the entire range. Smart transmission system matching speeds up pairing. The black box function stores essential flight data. Receiver operating statuses are indicated by an LED indicator. Smart pairing allows firmware updates wireless.

Features:

  • Increased protection against RF interference and more stable RF transmission
  • Simultaneous Twin 2.4GHz dual frequency transmission system with smart pairing
  • Black box function
  • High maximum operating range
  • Wireless firmware updates (OTA)
  • 8 high-precision PWM channels
  • S.BUS output port (16/24 channel mode)
  • S.BUS input port (with support for redundant connection of 2 receivers)
  • F.BUS / S.Port

Technical specifications:

  • Frequency: simultaneous dual 2.4 GHz
  • Dimensions: 54Ă—20Ă—10 mm (L*W*H)
  • Weight: 9.8 g
  • Operating voltage: 3.5–10 V (supply voltage min. 2.8 V).
  • Operating current: 80 mA at 5 V
  • External voltage measurement range via AIN2: 0–35 V
  • Antenna connector: IPEX4
  • Compatibility: 2.4 GHz dual-frequency simultaneous transmission system

€54.90

Inc. VAT
Quantity

Featured Products

TBS Crossfire Micro TX V2 STARTER Set Long range,Low Latency

TBS Crossfire Micro TX V2 STARTER Set Long range,Low Latency

The TBS CROSSFIRE is a long range R/C link based on the newest RF technology, capable of self-healing two-way communications and range beyond comprehension. With a sensitivity of -130dB, full RF-side diversity, tiny receivers for FPV quads, the TBS CROSSFIRE contains the most modern technology to provide a superior long range control link

The Crossfire Micro TX borrows the core technology from its larger brother, but is a JR-module transmitter simplified to the most sought-after features, at a killer price! For people looking to do extreme long range flights beyond 15-20km, the Crossfire TX is still the way to go. For anyone looking to penetrate buildings, fly mini quads or just explore your surroundings a few kilometers away, the Micro TX is the perfect companion. It will still go out up to 40km, just like its bigger brother. But it costs less than half the price.

 Features:

  •     Long range, adaptive and robust remote control system for your aircraft
  •     Immune to on-board noise
  •     Two-way communication link with real-time link vitals and telemetry
  •     Self-healing & frequency hopping (DSSS, FHSS)
  •     Adaptive bandwidth control and range optimization
  •     RX beacon mode to recover your downed aircraft
  •     Super easy binding and configuration via built-in display of your R/C
  •     Low latency, 150Hz update rate (3x faster than typical RC links) control for perfect immersive feeling
  •     Two receiver models: 8 port Diversity Rx, 4 port Mini-receiver (4g weight!)
  •     8 or 12ch output via SBUS/PPM/CRSF on both receivers
  •     Ability to fly with multiple friends at the same time (10 or more)
  •     Selectable RF power from 25mW to 250mW (local restrictions apply)
  •     Transmitter LED shows link health
  •     Micro-receiver for smaller drones. Smaller than you think!
  •     Software updates via RF Link

 
Technical specifications:

  •     Frequency Band: 868MHz- EU
  •     Input Voltage: 6.0 - 13V
  •     Connector : USB-C
  •     Power consumption: 1.1W (@10mW) - 2W (@100mW)
  •     Dimensions: 65 x 48 x 22 mm (JR module size)
  •     Weight: 48g

Package includes

  • 1 x TBS Crossfire Micro TX V2
  • 3 x TBS Crossfire Nano RX
  • 3 x TBS Crossfire Micro Receiver Antenna
  • 3 x TBS Crossfire Immortal T V2 Antenna
  • 1 x Taranis QX7 Mod
  • 3 x Cables and Shrink Tubes set

€199.99

Inc. VAT
Quantity
UAVsystems Fireproof LiPo carry and storage Safe Bag for 12s-14s 340mm long

UAVsystems Fireproof LiPo carry and storage Safe Bag for 12s-14s 340mm long

The LiPo Safe sack/bag is a hi-tech bag made of space-age materials that has the ability to contain a lithium polymer battery fire or charging mishap. Place your lithium polymer battery inside the LiPo Safe and extend the charging wires through the top flap. Charge the lipo batteries when they’re in the LiPo Safe for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the LiPo Safe’s fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the LiPo Safe.

This is a long version of the Safe product, measuring internal dimensions of 340x70x65mm, fits long Stick Lipos 12s and even some 14S packs- verify the size of your lipo to be sure it fits inside the bag.

The LiPo Safe is sealed with a thick, industrial strength, Velcro flap. The current LiPo Safe is designed to handle a lithium polymer battery mishap

Before using the LiPo Safe you must read and understand the LiPo Safe Safety Instructions. We assume absolutely no liability for any damages of any kind - even with proper use. When using the LiPo Safe, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LiPo Safe on a non-flammable surface and in a ventilated area. Avoid damage to the LiPo Safe and not use the LiPo Safe if it is damaged.

Instructions to use:

Ensure that charger rate is properly set and polarity is correct

  1. Attach charging leads to battery
  2. Place battery in LiPo Safe towards the bottom
  3. Place LiPo Safe on non-flammable surface
  4. Route charge leads through vent at the top seam of the LiPo Safe
  5. Close top flap of LiPo Safe and press hook and loop closure fully closed
  6. Charge battery using proper charging practices
  7. Always practice extreme caution when charging and never leave a charging battery unattended

Please check the Video showing the use of Lipo Safe

€14.99

Inc. VAT
Quantity
RCPROPLUS REB 6808 Pro D6 P8 TWIN SQUARE SUPRA-X REB6808 PRO D6 6mm Bullet Connector 8 Pairs

RCPROPLUS REB 6808 Pro D6 P8 TWIN SQUARE SUPRA-X REB6808 PRO D6 6mm Bullet Connector 8 Pairs

This is a pack of 8 RCPROPLUS SUPRA-X REB6808 PRO D6 6mm Bullet Connector

Set including 8 PAIRS.


Featuring a unique patented banana plug lock design, these Pro-D6 connectors securely lock in place handling quick movements and vibrations, commonly found during extreme 3D flights, without coming apart. The stronger jacket and snaps extends the advantages of the previous generation of Supra X Connectors and makes them better.

These connectors are a great solution for your high current and high voltage demands offering a large, low resistance surface patch for efficient power transfer. The 24K Gold Plated bullet plugs feature a recessed wire cavity and solder windows making assembly hassle free, while the sheath uses high temperature capable, impact-resistant plastic imported from Japan.

Cover material:IDEMITSU plastic
Banana connector diameter:6mm
Suggested Wires:8AWG-10AWG
Capacity (Continuous):200A
Capacity (Burst):240A
Banana connector material:Class A Cooper C54 Series
Plating:24K Gold / Flash

Features:
Connection between battery and ESC
Can be used for 4 batteries and 4 ESCs (or 4 charger cables)

Package Included:
4 x Set
8 x 6mm Female& Male Bullet Connector

€35.90

Inc. VAT
FPV x230 Racer With Gimbal ,1080P Wide Angle HD Camera RC Quadcopter RTF

FPV x230 Racer With Gimbal ,1080P Wide Angle HD Camera RC Quadcopter RTF

FPV x230 Racer With Gimble,1080P Wide Angle HD Camera RC Quadcopter RTF

  • Built-in 120° wide angle and 1920 x 1080P HD camera to get the high quality shooting;
  • Equipped with 2200mAh smart flight battery.
  • Flip 360° steadily;
  • Real-time transmission for FPV action video.

Remote control:

  • Built-in video transmitter to improve the transmission quality and reliability of communication;
  • Equipped with camera and operation button to control easily.

Package Included:

  • 1 x X230 Multicopter
  • 1 x Battery
  • 2 x ABS 5030 propeller
  • 1 x Balance charger
  • 1 x Charger cable
  • 1 x Adapter
  • 1 x 4 pins connection wire
  • 1 x Screw bag

€359.00

Inc. VAT
Quantity
ZD-937/B/ESD Digital regulated Soldering Station, pre-selection buttons

ZD-937/B/ESD Digital regulated Soldering Station, pre-selection buttons

Soldering Station ZD-937, black, 150°C - 450°C, 48W,ESD-protection, with pre-selection buttons 100, 200, 300°C.

The station is ideal for home elektronics, school, workshop, service, production and lab.

Among the easy and quick temperature adjustment with the up-/down-buttons in 1°C- and 10°C-steps, it is possible to pre-select 100°C, 200°C and 300°C with the related button.

  • Compact, solid and insulated housing.
  • Station and soldering iron pod are arrangeable seperately.
  • Complete with soldering iron pod and soldering sponge.
  • LCD display with ilumination shows must- and actual value.
  • Energy display
  • 3 pre-selectionable fixed temperatures
  • Electronical sensor
  • Temperature controll
  • Short heating-up time thanks to its generous designed power supply
  • Powerful 48W soldering iron for a wide range of application
  • Temperature adjustment with buttons from 150 to 450°C, 1°C and 10°C steps
  • Optical and accoustic error message in case of malfunction
  • ESD protection

Technical Specification:

  • Input Voltage: 230V (220-240V), 50 Hz
  • Power of soldering iron: 48W
  • Fuse: T 1A/250V
  • 150°C-450°C temperature adjustment with 1°C- and 10°C-steps
  • Display accuracy: 5%
  • LC-Display with 3 1/2 digits
  • Dimension WxHxD: 210x125x135mm
  • Weight 1,8kg

Delivery:

  • Soldering station ZD-937
  • Soldering iron pod with drawer and soldering sponge
  • Soldering iron with tip 1,6 mm
  • German and english manual

€59.90

Inc. VAT
Quantity
10 Piece Combination Spanner Set 4-11mm

10 Piece Combination Spanner Set 4-11mm

This "economy" spanner set includes just about all the sizes you will ever need on a model heli.
Ideal for you field box and building bench.

Sizes included are : 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm.
Set of 10 spanners

€24.00

Inc. VAT
Quantity
Custom assembled TITAN DC5 HD v1.4 Compatible with DJI Air Unit PNP

Custom assembled TITAN DC5 HD v1.4 Compatible with DJI Air Unit PNP

TITAN DC5 w/ DJI Air Unit BNF built for  the amazing new DJI FPV system, this quad makes flying FPV truly breathtaking. With the 720p video shown at 120fps through the goggles, DJI has set the bar at a new high for clarity and image quality in an FPV system. This TITAN DC5 BNF is 5 inch quad which is no prop in view, equipped SucceX-D F7(50A 4-in-1 ESC) Stack and popular XING motor, everything you just need to bind and fly!

This model can accept up to 6s, but the motors mounted are designed to be used with 4S.

    You can use Any radio you want, you will need to add your receiver and bind and calibrate it.

    If you use your own DJI Remote Controller, you need to update beta-flight to 10.6.0 to set up and bind your DJI remote controller.

    ELECTRONICS // SucceX-D F7 Stack (50A 4-in-1 ESC):

    • Universal USB Type C connector instead of micro USB
    • Plug-and-Play. No need to solder tiny wires
    • Designed to support DJI Digital FPV.

    BNF // Parts lists

    • 1x TITAN DC5 HD Frame
    • 2x TPU camera side plate soft mount
    • 1x iFlight Lipo Strap
    • 2x Nazgul 5140 Propeller (Set of 4 - Color May Vary)
    • 4x XING 2207 Motor Unibell (4S 2450KV)
    • 1x SucceX- F7 Flight Controller
    • 1x SucceX BLHeli32 50A 4-in-1 ESC 2-6S

    €330.00

    Inc. VAT
    Quantity
    Sky hero Anakin Club FPV racer 215-5’’ ARF combo w.radio

    Sky hero Anakin Club FPV racer 215-5’’ ARF combo w.radio

    Sky hero Anakin Club FPV racer 215mm -5"’’ ARF combo, Our combo delivered with Best components we beleive are on the market today. We beleive that quality assembly can be done by customer, there are a lot of advantages to do so.
    See the specs below.

    • Anakin club racer Frame kit Xnova 2204-2300Kv motors, esc, props- Included and factory preinstalled.
         Note: if you choose other motors, you will need to assemble the kit yourself, you will receive all components, but not ARF version.
    • CC3D Metal Case controller included
    • PDB-Bec
    • FPV Camera included
    • RADIO link AT9 with receiver Sky hero version (white edition )

    Not included:

    • Lipo charger
    • Battery 3s 1300-1500 mah
    • VTX - optional

    Sky hero did it again, with the latest drone technology, you have the possibility to fly the freedom of birds.
    With competition racing and performance within the DNA of SKY HERO, this machine was created as serious racer for those who want the best.
    Club-racer- inherits the amazing design of the original sky hero Anakin, with new evolved concept.
    Strengthened with flat arms.
    this was developed with the vision that FPV racers deserve a near-indestructible machine, agile racer they can trust.
    Locked in trajectories and customizable.

    General specs of Club racer versions.

    • Full carbon frame- Crash resistant.
    • Innovative abutted A frame design.
    • Minimized vibrations distribution, Optimized shock absorption
    • 3K 4mm Carbon
    • Sandwitched frame plates
    • Fully protected electronics
    • Optimized Shape, size and frame thickness, delivering outstanding strength-to weight ratio
    • Responsiveness- so rigid, that you feel "At one" with your frame.

    ESSENTIALS

    •     Entirely designed for racing
    •     Flat arms conception for highest impact resistance
    •     Simplified option for easy components replacement
    •     Low drag, for higher speeds
    •     Electronics fully protected

    KEY FACTORS

    •     Premium choice for FPV
    •     High wind resistance
    •     Super fast
    €359.00

    €229.00

    36% Off Inc. VAT
    Quantity

    10K+ Products In Stock

    Real-Time Stock Levels


    Competitive Prices

    Earn Points, Secure Payments



    Top Customer Service

    Supported by Real Enthusiasts

    We're a team of certified engineers with 40 years experience in R/C, UAV and UAS.

    Our excellence is in our customer service. Our value stands in understanding what we sell.

    We have a real store in Belgium. We are there for you and accessible.

    Give us a try, you can be confident to get a real advice from modeler to modeler.

    Beginner or Expert, B2B and B2C, we're happy to serve you. Your passion is our passion!