Europe based Mega-Store of RC Helicopters, Drones, Planes

Protect your canopy edges, or use it as wire protection against carbon frames, use it combined with fuel tanks.. and much more.
this Strip including U shape Silicone. the profile is U shape and its made to fit canopies, Frames, and all possible sharp edges with 1-2mm thickness

See images for exact dimensions and sizes.

Silicone material, 1m long

This is a Do-it-yourself sensor kit to replace any needed Magnetic sensor.
the kit comes with clear instruction how to solder the wires, and place it best way, you may also print your 3D mount if needed, or use any PCB isolating material to make it yourself.

Kit including wire connector 30cm, sensor and heatshrink set.

Module size: 42.7mm*20.7mm*8.1mm

Direct Input of 60V , 24V output with 5A current for long-term stable operation.

Note: The module can work stable at 5A under the condition of good heat dissipation. If there is no heat dissipation measures, it is recommended to use it within 3.5A.

The R6303SB has an S.BUS system output port and 3 conventional system channel outputs. It can also be used with conventional system servos, etc. in addition to S.BUS system compatible servos and gyros, etc. When the linking procedure is performed, R6303SB recognizes the signal mode (FASST2.4GHz 7ch mode or 8ch/10ch/Multi-ch mode) automatically.

The R6303SB can change the output CH from seven groups (CH group table). In addition, the operating mode (high speed mode/normal mode) can be selected.
 

• FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system
• S.BUS port and 3 channels for conventional system
• High-Speed receiver

R6303SB Specifications:

• FASST-2.4GHz System (7ch/8ch/10ch/Multi-ch)
• S.BUS
• 3-channels for conventional system (not using the USB channels)
• Dual Antenna Diversity
• Size: 22.5 x 37.4 x 9.3 mm
• WeighT: 7.2 g
• Power Requirement: 3.7-7.4V
• Voltage Range: 3.5-8.4V

Receiver is brand new, but delivered without original box since it was separated from the radio set

I2C LED Module for Pixhawk PX4 with USB Extension Function External Indicators Full Color LED, with protective cover

Pixhawk-RGB module has the following characteristics:

To extend to the exterior RGB LEDs to display, when connected to the module, built-in RGB flight control automatically turns off;

Increase the USB port for easy links from external USB cable, without limitation flight control installation location;

Pixhawk onboard identical Toshiba LED controller and Osram's high-brightness RGB LED

The AP_Periph CAN Node L431 allows you to easily connect multiple ardupilot peripherals via this node to act as a hub between your sensors and the flight controller. This is ideal for some smaller flight controllers that do not have as much I/O.

Features

CAN-L431 is an Adapter Node based on ArudPilot AP_Periph firmware.

With this board, you can easily utilize the ArduPilot driver library to convert ArduPilot supported GNSS, Compass, Barometer,Airspeed sensor, and GPIO based (PWM, Buzzer/LED notify) peripherals to DroneCAN bus peripherals.

Specifications

• MCU: STM32L431xC, 256KB Flash
• CAN transceiver data rates up to 5 Mbit/s in the CAN FD fast phase
• 1x CAN, DroneCAN Protocol (2x GH-4P connectors in parallel)
• 3x UARTs
  • UART1, spare
  • UART2, MSP default, DFU
  • UART3, GPS default
• 1x I2C
  • for peripheral Airspeed sensor
  • for peripheral Barometer
• 1x SPI
  • for peripheral RM3100
• 4x ADC
  • BATT_VOLT, PIN 5
  • BATT_CURR, PIN 6
  • BATT2_VOLT, PIN 15
  • BATT2_CURR, PIN 16
• 5x PWM outputs
• 1x GPIO with TIM16 for buzzer
• ST debug, SWCLK & SWDIO

• LED
  • Blue, Fast blinking, Booting
  • Blue, Slow blinking, working
  • Red, 3.3V indicator

• Input voltage range: 4.5~5.5V @5V pad/pin
• Power consumption: 40mA
• Operating Temperatures: -20~80 °C

• Physical
  • 2x JST-GH-4P(SM04B-GHS-TB) for CAN
  • 1x JST-GH-4P(SM04B-GHS-TB) for I2C
  • 1x JST-GH-6P(SM06B-GHS-TB) for UART3+I2C
  • Board Size: 26mm*26mm*6mm. 3.7g
• Firmware
  • ArduPilot AP_Periph MatekL431-Periph, or MatekL431-Airspeed
  • Update via DroneCAN GUI Tool

Included:

• 1x CAN-L431 board
• 1x JST-GH-4P to JST-GH-4P 20cm silicon wire
• 1x JST-GH-6P to JST-GH-6P 20cm silicon wire

GT Power CCPM Servo Consistency Master is a very handy servo driver/tester that can test the consistency and set the centering for up to 3 servos simultaneously.

This is great for anyone who is setting up RC airplane, car, or CCPM 3D helicopter and would like to see if their servos are actually working or compare the response time of each servo before installing them in your model. Additionally, you can set your servo into neutral/center mode without having a Transmitter/Receiver.

There are 3 available test modes: Manual Mode, Neutral Mode, Automatic "window wiper" Mode

You can also connect 1-3 ESC to test and compare their reaction time respectivel

The device also can be used as a signal generator for electric speed controller (ESC). With it, you can test your motor system without using a transmitter and receiver

YGE 205HVT ESC Cable Set. This is a replacement cable set for the 205HVT. Package includes two BEC cables, one throttle cable, and one telemetry cable.

The TBS CROSSFIRE is a long range R/C link based on the newest RF technology, capable of self-healing two-way communications and range beyond comprehension. With a sensitivity of -130dB, full RF-side diversity, tiny receivers for FPV quads, the TBS CROSSFIRE contains the most modern technology to provide a superior long range control link

The Crossfire Micro TX borrows the core technology from its larger brother, but is a JR-module transmitter simplified to the most sought-after features, at a killer price! For people looking to do extreme long range flights beyond 15-20km, the Crossfire TX is still the way to go. For anyone looking to penetrate buildings, fly mini quads or just explore your surroundings a few kilometers away, the Micro TX is the perfect companion. It will still go out up to 40km, just like its bigger brother. But it costs less than half the price.

 Features:

•     Long range, adaptive and robust remote control system for your aircraft
•     Immune to on-board noise
•     Two-way communication link with real-time link vitals and telemetry
•     Self-healing & frequency hopping (DSSS, FHSS)
•     Adaptive bandwidth control and range optimization
•     RX beacon mode to recover your downed aircraft
•     Super easy binding and configuration via built-in display of your R/C
•     Low latency, 150Hz update rate (3x faster than typical RC links) control for perfect immersive feeling
•     Two receiver models: 8 port Diversity Rx, 4 port Mini-receiver (4g weight!)
•     8 or 12ch output via SBUS/PPM/CRSF on both receivers
•     Ability to fly with multiple friends at the same time (10 or more)
•     Selectable RF power from 25mW to 250mW (local restrictions apply)
•     Transmitter LED shows link health
•     Micro-receiver for smaller drones. Smaller than you think!
•     Software updates via RF Link

 
Technical specifications:

•     Frequency Band: 868MHz- EU
•     Input Voltage: 6.0 - 13V
•     Connector : USB-C
  
•     Power consumption: 1.1W (@10mW) - 2W (@100mW)
•     Dimensions: 65 x 48 x 22 mm (JR module size)
•     Weight: 48g

Package includes

• 1 x TBS Crossfire Micro TX V2
• 3 x TBS Crossfire Nano RX
• 3 x TBS Crossfire Micro Receiver Antenna
• 3 x TBS Crossfire Immortal T V2 Antenna
• 1 x Taranis QX7 Mod
• 3 x Cables and Shrink Tubes set

The LiPo Safe sack/bag is a hi-tech bag made of space-age materials that has the ability to contain a lithium polymer battery fire or charging mishap. Place your lithium polymer battery inside the LiPo Safe and extend the charging wires through the top flap. Charge the lipo batteries when they’re in the LiPo Safe for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the LiPo Safe’s fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the LiPo Safe.

This is a long version of the Safe product, measuring internal dimensions of 340x70x65mm, fits long Stick Lipos 12s and even some 14S packs- verify the size of your lipo to be sure it fits inside the bag.

The LiPo Safe is sealed with a thick, industrial strength, Velcro flap. The current LiPo Safe is designed to handle a lithium polymer battery mishap

Before using the LiPo Safe you must read and understand the LiPo Safe Safety Instructions. We assume absolutely no liability for any damages of any kind - even with proper use. When using the LiPo Safe, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LiPo Safe on a non-flammable surface and in a ventilated area. Avoid damage to the LiPo Safe and not use the LiPo Safe if it is damaged.

Instructions to use:

Ensure that charger rate is properly set and polarity is correct

1. Attach charging leads to battery
2. Place battery in LiPo Safe towards the bottom
3. Place LiPo Safe on non-flammable surface
4. Route charge leads through vent at the top seam of the LiPo Safe
5. Close top flap of LiPo Safe and press hook and loop closure fully closed
6. Charge battery using proper charging practices
7. Always practice extreme caution when charging and never leave a charging battery unattended

Please check the Video showing the use of Lipo Safe

This is a pack of 8 RCPROPLUS SUPRA-X REB6808 PRO D6 6mm Bullet Connector

Set including 8 PAIRS.

Featuring a unique patented banana plug lock design, these Pro-D6 connectors securely lock in place handling quick movements and vibrations, commonly found during extreme 3D flights, without coming apart. The stronger jacket and snaps extends the advantages of the previous generation of Supra X Connectors and makes them better.

These connectors are a great solution for your high current and high voltage demands offering a large, low resistance surface patch for efficient power transfer. The 24K Gold Plated bullet plugs feature a recessed wire cavity and solder windows making assembly hassle free, while the sheath uses high temperature capable, impact-resistant plastic imported from Japan.

Cover material:IDEMITSU plastic
Banana connector diameter:6mm
Suggested Wires:8AWG-10AWG
Capacity (Continuous):200A
Capacity (Burst):240A
Banana connector material:Class A Cooper C54 Series
Plating:24K Gold / Flash

Features:
Connection between battery and ESC
Can be used for 4 batteries and 4 ESCs (or 4 charger cables)

Package Included:
4 x Set
8 x 6mm Female& Male Bullet Connector

FPV x230 Racer With Gimble,1080P Wide Angle HD Camera RC Quadcopter RTF

• Built-in 120° wide angle and 1920 x 1080P HD camera to get the high quality shooting;
• Equipped with 2200mAh smart flight battery.
• Flip 360° steadily;
• Real-time transmission for FPV action video.

Remote control:

• Built-in video transmitter to improve the transmission quality and reliability of communication;
• Equipped with camera and operation button to control easily.

Package Included:

• 1 x X230 Multicopter
• 1 x Battery
• 2 x ABS 5030 propeller
• 1 x Balance charger
• 1 x Charger cable
• 1 x Adapter
• 1 x 4 pins connection wire
• 1 x Screw bag

Soldering Station ZD-937, black, 150°C - 450°C, 48W,ESD-protection, with pre-selection buttons 100, 200, 300°C.

The station is ideal for home elektronics, school, workshop, service, production and lab.

Among the easy and quick temperature adjustment with the up-/down-buttons in 1°C- and 10°C-steps, it is possible to pre-select 100°C, 200°C and 300°C with the related button.

• Compact, solid and insulated housing.
• Station and soldering iron pod are arrangeable seperately.
• Complete with soldering iron pod and soldering sponge.
• LCD display with ilumination shows must- and actual value.
• Energy display
• 3 pre-selectionable fixed temperatures
• Electronical sensor
• Temperature controll
• Short heating-up time thanks to its generous designed power supply
• Powerful 48W soldering iron for a wide range of application
• Temperature adjustment with buttons from 150 to 450°C, 1°C and 10°C steps
• Optical and accoustic error message in case of malfunction
• ESD protection

Technical Specification:

• Input Voltage: 230V (220-240V), 50 Hz
• Power of soldering iron: 48W
• Fuse: T 1A/250V
• 150°C-450°C temperature adjustment with 1°C- and 10°C-steps
• Display accuracy: 5%
• LC-Display with 3 1/2 digits
• Dimension WxHxD: 210x125x135mm
• Weight 1,8kg

Delivery:

• Soldering station ZD-937
• Soldering iron pod with drawer and soldering sponge
• Soldering iron with tip 1,6 mm
• German and english manual

This "economy" spanner set includes just about all the sizes you will ever need on a model heli.
Ideal for you field box and building bench.

Sizes included are : 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm.
Set of 10 spanners

TITAN DC5 w/ DJI Air Unit BNF built for  the amazing new DJI FPV system, this quad makes flying FPV truly breathtaking. With the 720p video shown at 120fps through the goggles, DJI has set the bar at a new high for clarity and image quality in an FPV system. This TITAN DC5 BNF is 5 inch quad which is no prop in view, equipped SucceX-D F7(50A 4-in-1 ESC) Stack and popular XING motor, everything you just need to bind and fly!

This model can accept up to 6s, but the motors mounted are designed to be used with 4S.

You can use Any radio you want, you will need to add your receiver and bind and calibrate it.

If you use your own DJI Remote Controller, you need to update beta-flight to 10.6.0 to set up and bind your DJI remote controller.

ELECTRONICS // SucceX-D F7 Stack (50A 4-in-1 ESC):

• Universal USB Type C connector instead of micro USB
• Plug-and-Play. No need to solder tiny wires
• Designed to support DJI Digital FPV.

BNF // Parts lists

• 1x TITAN DC5 HD Frame
• 2x TPU camera side plate soft mount
• 1x iFlight Lipo Strap
• 2x Nazgul 5140 Propeller (Set of 4 - Color May Vary)
• 4x XING 2207 Motor Unibell (4S 2450KV)
• 1x SucceX- F7 Flight Controller
• 1x SucceX BLHeli32 50A 4-in-1 ESC 2-6S

Sky hero Anakin Club FPV racer 215mm -5"’’ ARF combo, Our combo delivered with Best components we beleive are on the market today. We beleive that quality assembly can be done by customer, there are a lot of advantages to do so.
See the specs below.

• Anakin club racer Frame kit Xnova 2204-2300Kv motors, esc, props- Included and factory preinstalled.
     Note: if you choose other motors, you will need to assemble the kit yourself, you will receive all components, but not ARF version.
• CC3D Metal Case controller included
• PDB-Bec
• FPV Camera included
• RADIO link AT9 with receiver Sky hero version (white edition )

Not included:

• Lipo charger
• Battery 3s 1300-1500 mah
• VTX - optional

Sky hero did it again, with the latest drone technology, you have the possibility to fly the freedom of birds.
With competition racing and performance within the DNA of SKY HERO, this machine was created as serious racer for those who want the best.
Club-racer- inherits the amazing design of the original sky hero Anakin, with new evolved concept.
Strengthened with flat arms.
this was developed with the vision that FPV racers deserve a near-indestructible machine, agile racer they can trust.
Locked in trajectories and customizable.

General specs of Club racer versions.

• Full carbon frame- Crash resistant.
• Innovative abutted A frame design.
• Minimized vibrations distribution, Optimized shock absorption
• 3K 4mm Carbon
• Sandwitched frame plates

• Fully protected electronics
• Optimized Shape, size and frame thickness, delivering outstanding strength-to weight ratio
• Responsiveness- so rigid, that you feel "At one" with your frame.

ESSENTIALS

•     Entirely designed for racing
•     Flat arms conception for highest impact resistance
•     Simplified option for easy components replacement
•     Low drag, for higher speeds
•     Electronics fully protected

KEY FACTORS

•     Premium choice for FPV
•     High wind resistance
•     Super fast