Regulators & BEC

Regulators & BEC

In this section you can find the Newest technology Voltage regulators, Power Box and BEC's , Powerfull and last forever.
Setup of Flight packs with regulator is a choice of the Champions.

Products


  • Jeti SingleBec

    Jeti SingleBec

    Jeti SingleBec

    SingleBEC is a linear regulator to provide power for a standard servo with a maximum input voltage of 6V. The SingleBEC can also be used to provide power for the control units of helicopters or multi-rotor aircraft.  

    Its great advantage is that it allows the use of standard servos in systems designed for the so-called High-Voltage servos. Due to its dimensions, the SingleBEC is designed even for small airplane models. Its internal filtering improves the quality of the output voltage for the servo.

    The small size and low weight of the SingleBEC allows for very simple installation in all parts of the plane. Due to its performance parameters, the Single BEC is suitable for the category of micro and mini servos with load strengths of @ 25 kg/cm at 6V.

    Specification:

    • Weight [g] 5
    • Dimensions [mm]  19 x 9.3 x 6.6
    • Sustained current [A]     1
    • Operational temperature [°C] -20 > 75
    • Recommended input voltage [V] 5.5 > 8.4
    • Output voltage [V]     5.5
    • Number of battery inputs 1
    • Input voltage max. [V]     24
    • Peak current (max 5s) [A] 15
    SKU: J-SB
    €21.90
    inc. VAT

     72HR STOCK
  • Jeti Voltage Regulator MAX BEC 2D Plus EX 5-6V/20A w/Magnetic Switch

    Jeti Voltage Regulator MAX BEC 2D Plus EX 5-6V/20A w/Magnetic Switch

    The Jeti Max BEC 2D Plus EX is the latest linear voltage regulator from Jeti, produced to very high standards in Europe. The Max BEC 2D Plus features a magnetic switch, so there is no mechanical wear-and-tear from switching the unit on and off. The unit also has a large heat-sink to dissipate heat.

    For the first time ever, your models receiver system can be turned ON/OFF with a simple flip of the switch, wirelessly from the Jeti DC/DS transmitters. The R3/RSW receiver fully replaces Jetis Magnetic Switch which is widely used with Jeti Voltage Regulators as well as their Electronic Switches. Simply cut off the existing switch, install a Male JR type connector and plug it to the #3 port of the R3/RSW receiver.

    In addition to its magnetic switch feature, the 2D is programmable using the Jeti Box and is also Duplex 2.4EX compatible, allowing audible alarms to be configured for low input voltage or high-temperature and allowing real-time feedback of input voltage and temperature, as well as output voltage selection, wirelessly from the Jeti Box.

    Redundant inputs are provided for power-supply and the output features an MPX type socket, directly supporting the Duplex R12, R14, R18 receivers and all Duplex EPC receivers. The maximum burst output is 20A. The recommended input power is 5.5-8.4V, e.g. two-cell lithium polymer batteries or 5-6 nickel-based cells. You may also use 2-cell LiFe battery pack.

    Screws and mounting-lugs are included to mount the device in your model as well as the magnetic key and face-plate. Decals are also included to allow the informative cover of the unit to be replicated on the outside of your model.

    For best results, ensure that the all BECs are installed at least 2" (50mm) away from your receiver and antenna.nt endurance

    Specifications

    Manufacturer: Jeti Model
    Type: Linear Regulator
    Max Input Voltage: 16V
    Min Input Voltage: 5.5V
    Output Voltage: 5, 5.4, 5.7, 6V Adjustable
    Output Current: 12A Continues/20A Peak
    Dimensions: 100mm x 29mm x 16mm
    Weight: 85g
    Max #Servos: 8-10 Analog, 6-8 Digital
    Connector: Multiplex
    Applications: Airplanes/Helicopters

    SKU: JEX-MB2-DP
    €92.90
    inc. VAT

     LOW STOCK
    NEW
  • Mikado Current/Voltage/Capacitysensor for VBar Control

    Mikado Current/Voltage/Capacitysensor for VBar Control

    Mikado Current/Voltage/Capacitysensor for VBar Control

    Hardware Features of the Current/Voltage/Capacity Sensor for flight packs:

    • Individually precision calibrated
    • Optocoupler
    • Reverse battery protection
    • No influence from motor or current carrying wires

    Software Features:

    • Direct displaying from voltage and capacity
    • Max. current and min. voltage storage
    • Logfile data from the flight
    • Battery Logbook with names
    • Adjustable capacity, residual capacity and voltage for each battery
    • Residual capacity is shown as bar in the radio display
    • Overdischarge Warning
    • Warning at use of not fully charged batteries
    • Loud speaker announcement for reducing battery capacity

    Notes:
    Requires a VBar with Spektrum Satellite connectors (telemetry bus for VBar Control)
    Not suitable for measuring receiver packs only (e.g. on a nitro heli)
    extracted capacities are not added up, measurement only on a per-flight basis

    Specifications:

    • Current Consumption     2.5 mA
    • Working Temperature Range     -5 to 50 °C, 23 to 122 °F
    • Dimensions     approx. 20 x 20 x 10 mm
    • Power Rating     120 A continuous, 330 A peak
    • Effective Range (current)     0.1 A to 300 A
    • Effective Range (voltage)     5 V to 100 V (2s to 16s LiPo)
    • Resolution     0.01 A / 0.01 V

    Contents:
    Device   Voltage/Current Sensor with connecting wires to battery and ESC
    Connecting Wire     Sensor wire 500 mm

    Accessories:

    • Connecting Wire 250 mm     04898
    • Connecting Wire 500 mm     04899
    • Battery ID Reader     04907
    • Battery ID Tags (10 pc.) 04908
    • Miscellaneous
    SKU: MIK-4890
    €74.90
    inc. VAT

     72HR STOCK
  • Optipower ULTRA-GUARD 430 Back Up Solution Combo OPRUS2S

    Optipower ULTRA-GUARD 430 Back Up Solution Combo OPRUS2S

    OPTIFUEL is building a highly respected reputation for developing products and accessories for the model enthusiast which now covers brands such as OPTIPOWER Ultra Guard 430 a new intelligent concept in model flight safety.

    ULTRA GUARD 430 is a small lightweight easy to install smart landing system designed to restore total backup control allowing you to land your model safely following a main power failure. A welcome new development and additional safeguard is the easy to fit Ultra Guard high intensity LED Flash Alarm..

    The device is plugged into a free port on your RX or FBL system and when you power up the device waits, monitors the system set voltage, then arms at that voltage less 0.5V. The device is then armed and monitoring the system voltage and the state of the buffer pack.
    If the buffer pack needs topping up it will do that and balance it from the main packs or RX pack and stop when it gets to a nominal 8.1V. The device samples the system voltage every 2mS and if the system voltage drops below the armed set voltage then the buffer pack steps in if the system voltage recovers it drops out, this is seamless. The device when working can and does indicate locally that its operational and if it is charging or not but this is not able to be seen at distance.
    A separate external high intensity LED can be fitted that shows you are on the buffer pack, this is an option and these can be cascaded if required. The device works across 4.6V to 8V.
    The combo version (the board and buffer pack) are bound together by clear shrink wrap as is the super combo version (inc LED system).
    The total weight is <39g inc LED <35g ex the LED. All parts can be purchased separately. The device can go to storage charge if its not going to be used for some time.

    Benefits & Features

    • Voltage Sensing 2 - 8.2V
    • Charges and balances at upto 2C in flight
    • Universal JR connector
    • JST-XH balance connection to main board
    • LED onboard status
    • External LED not included
    • Storage charge function
    • 5A continuous & 10A peak rated intermittent
    • Total wright just 40 grams
    • Vibration proof flexi board
    • Automotive industry quality components
    • Manufactured in Europe
    SKU: OPRUS2S
    €39.90
    inc. VAT

     IN STOCK
    NEW
  • Optipower ULTRA-GUARD 430 optional LED

    Optipower ULTRA-GUARD 430 optional LED

    The ULTRA Guard 430 optional LED

    Can be purchased as a separate item and can be cascaded one to another.

    OPTIFUEL is building a highly respected reputation for developing products and accessories for the model enthusiast which now covers brands such as OPTIPOWER Ultra Guard 430 a new intelligent concept in model flight safety.

    ULTRA GUARD 430 is a small lightweight easy to install smart landing system designed to restore total backup control allowing you to land your model safely following a main power failure. A welcome new development and additional safeguard is the easy to fit Ultra Guard high intensity LED Flash Alarm..

    The device is plugged into a free port on your RX or FBL system and when you power up the device waits, monitors the system set voltage, then arms at that voltage less 0.5V. The device is then armed and monitoring the system voltage and the state of the buffer pack.
    If the buffer pack needs topping up it will do that and balance it from the main packs or RX pack and stop when it gets to a nominal 8.1V. The device samples the system voltage every 2mS and if the system voltage drops below the armed set voltage then the buffer pack steps in if the system voltage recovers it drops out, this is seamless. The device when working can and does indicate locally that its operational and if it is charging or not but this is not able to be seen at distance.
    A separate external high intensity LED can be fitted that shows you are on the buffer pack, this is an option and these can be cascaded if required. The device works across 4.6V to 8V.
    The combo version (the board and buffer pack) are bound together by clear shrink wrap as is the super combo version (inc LED system).
    The total weight is <39g inc LED <35g ex the LED. All parts can be purchased separately. The device can go to storage charge if its not going to be used for some time.

    SKU: OPRLED
    €20.90
    inc. VAT

     IN STOCK
  • OPTIPOWER ULTRA-Guard 430 Solution SUPER Combo (inc external LED device)

    OPTIPOWER ULTRA-Guard 430 Solution SUPER Combo (inc external LED device)

    OPTIPOWER is building a highly respected reputation for developing products and accessories for the model enthusiast which now covers brands such as OPTIPOWER Ultra Guard 430 a new intelligent concept in model flight safety.

    ULTRA GUARD 430 is a small lightweight easy to install smart landing system designed to restore total backup control allowing you to land your model safely following a main power failure. A welcome new development and additional safeguard is the easy to fit Ultra Guard high intensity LED Flash Alarm..
    The device is plugged into a free port on your RX or FBL system and when you power up the device waits, monitors the system set voltage, then arms at that voltage less 0.5V. The device is then armed and monitoring the system voltage and the state of the buffer pack.
    If the buffer pack needs topping up it will do that and balance it from the main packs or RX pack and stop when it gets to a nominal 8.1V. The device samples the system voltage every 2mS and if the system voltage drops below the armed set voltage then the buffer pack steps in if the system voltage recovers it drops out, this is seamless. The device when working can and does indicate locally that its operational and if it is charging or not but this is not able to be seen at distance.
    A separate external high intensity LED can be fitted that shows you are on the buffer pack, this is an option and these can be cascaded if required. The device works across 4.6V to 8V.

    The many features of OPTIPOWER Ultra guard 430 are :

    • Voltage sensing from 5 to 9 Volts.
    • Charges and balances in flight.
    • Universal JR connector.
    • JST-XH balance connection to main board.
    • LED system status.
    • Storage charge function.
    • 7A continuous and 10A rated intermittent.
    • Total combo weight less than 39 grams.
    • Available and sold as separate single part items.
    • Vibration proof flexible board.
    • Automotive industry quality components. manufactured in Europe.

    The combo version (the board and buffer pack) are bound together by clear shrink wrap as is the super combo version (inc LED system).
    The total weight is <39g inc LED <35g ex the LED. All parts can be purchased separately. The device can go to storage charge if its not going to be used for some time.

    SKU: OPRUS2S-L
    €49.90
    inc. VAT

     IN STOCK
  • Power Supply UBEC 3A For FPV Multicopter

    Power Supply UBEC 3A For FPV Multicopter

    12V Power Supply UBEC Gimbal Flight Control AV Transmitter For FPV Multicopter Quadcopter

    • Specially design for multicopter
    • Metal block case with great heat dissipation, LED indicators
    • Metal shielding shell, good heat dissipation, the user can use double sided tape to stick it anywhere in the plane, you can also use screws.
    • This product ripple, high efficiency, and provide a steady output currents up to 3A for image transmission, brushless head, flight control, photographic equipment, power use.

    Technical parameters:

    • Input Voltage:  7-26V
    • Output voltage:  5.2 / 12V
    • Current:  3A
    • Weight:  9g
    • Size:  27* 17* 5mm

    Warning:

    • Battery polarity cannot be reversed.
    • Voltage cannot exceed the operating voltage range of products; this will cause damage to the product.

     

    SKU: FPV-BEC
    €12.00
    inc. VAT

     IN STOCK
  • RJX Dual Output Power BEC , 40 Amp

    RJX Dual Output Power BEC , 40 Amp

     RJX Dual Output power BEC , 40 Amp

    • Metal case, 40 amps Max current.
    • Dimensions: 29x45x16mm
    • weight : 51 Grams
    • Input:3S-14S lipos, 11-60V
    • Adjustable Output voltage :5.8, 7.5,8.2V
    • Max peak current: 40A

    Attention: do not use in Parralel with other BEC devices when connecting RX/SERVO side of the circuit.

    SKU: RJX1561
    €69.00
    inc. VAT

  • Step Down regulator

    Step Down regulator

    Tail Servo Step-Down Voltage is ideally designed to step-down a voltage source of 6 volts that is outputted from any external BEC (battery eliminator circuit) down to 5.1 volts.

    This allows an external 6 volt BEC to be used with digital servos that are not capable of handling 6 volts. The Tail Servo Step-Down Voltage is equipped with male/female servo plugs and is ideally used in series with the RC model’s gyro and rudder servo to prevent any harmful damage or overloading to your servo. The Tail Servo Step-Down Voltage can also be used with any other applications that require a step down power voltage of approximately 0.8 volts

    SPECIFICATIONS:

    Height ----- 4 mm
    width ----- 8 mm
    Length ----- 12 mm
    Weight ----- 4 grams

    High power component to withstand current of up to 5 Amps continuous, 10 Amps peak.
    Prevents harmful damage and overloading to the digital rudder/tail servo.
    plug and play Easy installation

    SKU: WRL-STVR
    €4.00
    inc. VAT

     IN STOCK
  • Voltage Regulator CC BEC 2.0 Castle Creations

    Voltage Regulator CC BEC 2.0 Castle Creations

    CC BEC 2.0 – THE NEXT GENERATION OF VOLTAGE REGULATORS (BEC) FROM CASTLE CREATIONS!

    From the trusted manufacturer of BECs comes the next generation of voltage regulators.  Designed and assembled in the USA1, Castle Creations’ CC BEC 2.0 gives users higher voltage ranges in two unique packages.   For pilots there is a smaller, lightweight (0.7 oz.) design capable of 14 amps peak, perfect for sport flying, helicopters, and UAVs.  Racers, crawlers, and other splashers can now integrate a 15 amp peak power regulator in a CNC machined, aluminum case.  Both versions handle up to an impressive 14S without brake enabled or 12S with brake.

    The CC BEC 2.0 complements our established line of BECs hobbyists have relied on for years.  With hundreds of thousands in the field, users can count on this new design to power today’s high-power, digital servos and accessories safely.  The CC BEC 2.0 features heavy duty, dual output wires that will provide clean power to sensitive radio equipment. Castle Link2 can be used to set the output from 4.75 to 12 volts and power today’s power hungry servos, cameras, and other accessories.   Do it right the first time, invest in the CC BEC 2.0 to protect expensive electronics for the long haul.

    SKU: CC-010-0154-00
    €47.90
    inc. VAT

     72HR STOCK
  • Waterproof Voltage Regulator CC BEC 2.0 Castle Creations

    Waterproof Voltage Regulator CC BEC 2.0 Castle Creations

    CC BEC 2.0 – THE NEXT GENERATION OF VOLTAGE REGULATORS (BEC) FROM CASTLE CREATIONS!

    From the trusted manufacturer of BECs comes the next generation of voltage regulators.  Designed and assembled in the USA1, Castle Creations’ CC BEC 2.0 gives users higher voltage ranges.
    For pilots there is a smaller, lightweight (0.7 oz.) design capable of 14 amps peak, perfect for sport flying, helicopters, and UAVs.  Racers, crawlers, and other splashers can now integrate a 15 amp peak power regulator in a waterproof (WP), CNC machined, aluminum case.  Both versions handle up to an impressive 14S without brake enabled or 12S with brake.

    The CC BEC 2.0 complements our established line of BECs hobbyists have relied on for years.  With hundreds of thousands in the field, users can count on this new design to power today’s high-power, digital servos and accessories safely.  The CC BEC 2.0 features heavy duty, dual output wires that will provide clean power to sensitive radio equipment. Castle Link2 can be used to set the output from 4.75 to 12 volts and power today’s power hungry servos, cameras, and other accessories.   Do it right the first time, invest in the CC BEC 2.0 to protect expensive electronics for the long haul.

    SKU: CC-010-0153-00
    €52.00
    inc. VAT

     LOW STOCK
  • ZTW 6A External BEC (UBEC)

    ZTW 6A External BEC (UBEC)

    These high power external BECs manufactured by ZTW have been specifically designed for extreme aerobatics and therefore have the capability to support the higher momentary peak demand loads to eliminate the possibility of unwanted shutdowns, and are also capable of supporting continuous simultaneous multiple servo operations typically found in CCPM equipped hardcore 3D E-helicopters.

    Features:

    • Switch mode
    • Easy setup and operation
    • Battery polarity reversal protection (unit will not function if power connection is wrong)
    • Status indicator LED shows when BEC is working
    • Advanced CPU decreased the electromagnetic interference to ensure optimal performance of the RX

    Specifications:

    • Output: 5.0V/6A, 5.5V/6A, or 6.0V/6A  (changeable with jumper)
    • Input Voltage: 6V-25V (2-6s LiPo; 5-18 cell Ni-XX
    • Output Current: 6A Continuous, 10A Burst
    • Weight: 18g
    • Dimensions: 45 x 23 x 10mm

     

    SKU: UBEC6A
    €13.00
    inc. VAT


Manufacturers

Back