eRCmarket

eRCmarket

eRCMarket is a company located in belgium, selling over 9000 products, serving community of modelers worldwide.

we proud of our service, quality of products, competitive prices

www.ercmarket.com

Products


  • OpenPilot CC3D EVO Flight Controller, 32-bit Flexiport w/out Satellite socket

    OpenPilot CC3D EVO Flight Controller, 32-bit Flexiport w/out Satellite socket

    CC3D Hardware Features:

    • Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
    • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
    • Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
    • Software support for Windows, Mac and Linux.
    • Direct high speed USB support with no drivers required, a truly plug and play device.
    • Futaba S-BUS hardware support.
    • Innovative Flexi-port technology for superior port flexibility.
    • 4Mbits on-board EEPROM for configuration storage.

    Flexiport:

    This flightcontroller also offers an innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.
     
    Superior user experience:

    OpenPilot tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.
     
    OpenPilot software is designed to be used by everybody! All major operating systems are supported and extra packages are also available. The software is all Free software under the GPLv3 license.

    Sensors and Components:

    • 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
    • Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, and Futaba S.Bus receivers.
    • Simultaneous support for multiple receivers.
    • ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
    • MainPort functions (configurable): serial telemetry (default), GPS, S.Bus.
    • FlexiPort (configurable): serial telemetry, GPS, or I2C peripherals (under development)
    • 10 PWM outputs to servos or ESC’s, or for camera stabilization
    • Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
    • Onboard USB connectivity for easy configuration.
    • USB and serial telemetry and configuration
    • Supported by powerful OpenPilot GCS
    • 4 Mbit onboard memory
    • 3C Quaternion based complementary filter running at 500Hz

    Package Includes:

    • 1 x CC3D
    • 1 x 8pc wire set
    • 1 x 4pc expansion path wire set
    • 1 x Damping Board
    • 1 x Antenna Base

     

    SKU: CC3D
    €24.90
    inc. VAT

  • Paddles Carbon 2mm

    Paddles Carbon 2mm

    Special Shape carbon paddels, for Microhelicopters.Those paddles come with locking mechanism to insude they will never move on your flybar.Set of 2 Pcs
    SKU: SKU14701
    €24.90
    inc. VAT

     IN STOCK
  • Painted Fiber Glass Canopy 130X

    Painted Fiber Glass Canopy 130X

    Fusuno canopies are made with highest quality resin and fiberglass material to provide strong but flexible canopies. It helps prevent cracks that is normally seen in other canopies that are using lower quality material. All paints and clear coat are automobile grade provide great look, Great design at bargain price
    SKU: FUC-B130X012
    €23.90
    inc. VAT

     LOW STOCK
  • PANASONIC  6LR61 EVOLTA 9V

    PANASONIC 6LR61 EVOLTA 9V

     PANASONIC  6LR61 EVOLTA 9V

    SKU: PAN-6LR61EGE
    €6.90
    inc. VAT

     IN STOCK
  • Pinion 15 T

    Pinion 15 T

    Pinion gear, Fits Robbe Millenium , Avaliable in 15 T. Makes perfect Ratio for 80-90 size motors.

    SKU: RCUG-023
    €29.00 €49.00
    inc. VAT

     IN STOCK
  • Pinion 15T-Long

    Pinion 15T-Long

    Extended Pinion to fit Millenium Helis, This pinion will make ratio 1:8 for 90 size motors
    The longer sleeve is especially for double Bearing block

    SKU: RCUG-030
    €29.00
    inc. VAT

     IN STOCK
  • Pinion gear

    Pinion gear

    Pinion gear for ALU Gear box 10/12/14/16T
    SKU: KRF922-2
    €4.00
    inc. VAT

     IN STOCK
  • Pirate Crusher electric Racing Buggy 1/10

    Pirate Crusher electric Racing Buggy 1/10

    Pirate Crusher electric Racing Buggy 1/10

    Electric Racing Buggy 4x2
    Version ready to run, with radio 2.4GHz, battery NiMh 1800mAh and AC/DC charger.
    Electronics waterproof, allows to run in wet conditions (except total dumping).

    Specification:

    • Adjustable Ball differential
    • Strengthened plastic Frame
    • Handled Universal shaft drive rear
    • Hydraulic Shock absorbers front / rear with body thread to adjust the spring
    • Tie-rods with inverted thread
    • Engine Brushed size(format) 540
    • Wheel and tires included
    • Mini box for receiver and ESC
    • Tie-rods with inverted thread
    • Compact servo-saver
    • Adjustable Triangulation
    • Mini front bumper and motor protection
    • Polycarbonate pre-decorated body

    Box contents:

    • Radio 2,4 Ghz
    • Battery NiMh 1800
    • Charger 220 V 500 mAh
    • ESC Waterproof (Li-Po 2S or 3S / Ni-Mh 5 to 9 Cell)
    • Servo Waterproof (tork 3 kg)
    Size:

    • Scale: 1/10
    • Length: 430 mm
    • Height: 145 mm
    • Wheelbase: 285 mm
    • Weight: 1580 g
    SKU: T4913
    €149.90
    inc. VAT

     72HR STOCK
  • Pixhawk - GPS2 Port Cable

    Pixhawk - GPS2 Port Cable

    Used for connecting Here GNSS or Here+ GNSS Rover to GPS 2 port in PH2.1

    only useful when using Here or Here+ as a secondary GPS for Pixhawk2.1

    SKU: HX4-06011-GPS
    €5.50
    inc. VAT

     IN STOCK
  • Pixhawk 2.1 Cable Set

    Pixhawk 2.1 Cable Set

    Cables for accessories are JST to DF13 cables which are compatible with old pixhawk accessories, such as Telemetry, Power Brick or GPS It contains: TELEM Cable * 2 POWER Cable * 2 I2C Cable * 1 BUZZER Cable * 1 MICRO USB Cable * 1 GPS1 Cable(with saftey switch) * 1 GPS2 Cable * 1

    SKU: HX4-06009
    €15.00
    inc. VAT

     LOW STOCK
  • Pixhawk 2.1 CUBE

    Pixhawk 2.1 CUBE

    This is the Pixhawk 2.1 Cube only, intended for use as a replacement part and for integration by OEMs. The Cube will not function without a carrier board.

    Specifications

    Processor

    32-bit ARM Cortex M4 core with FPU
    168 Mhz/256 KB RAM/2 MB Flash
    32-bit failsafe co-processor
    Sensors
    Three redundant IMUs (accels, gyros and compass)
    InvenSense MPU9250, ICM20948 and/or ICM20648 as first and third IMU (accel and gyro)
    ST Micro L3GD20+LSM303D or InvenSense ICM2076xx as backup IMU (accel and gyro)
    Two redundant MS5611 barometers

    Power

    Redundant power supply with automatic failover
    Servo rail high-power (7 V) and high-current ready
    All peripheral outputs over-current protected, all inputs ESD protected

    Interfaces

    14x PWM servo outputs (8 from IO, 6 from FMU)
    S.Bus servo output
    R/C inputs for CPPM, Spektrum / DSM and S.Bus
    Analogue / PWM RSSI input
    5x general purpose serial ports, 2 with full flow control
    2x I2C ports
    SPI port
    2x CAN Bus interface
    3x Analogue inputs (3.3V and 6.6V)
    High-powered piezo buzzer driver (on expansion board)
    High-power RGB LED (I2C driver compatible connected externally only)
    Safety switch / LED

    SKU: HX4-06005
    €195.00
    inc. VAT

  • Pixhawk 2.1 The Cube Standard Set Flight controller Fix wing and Multicopter

    Pixhawk 2.1 The Cube Standard Set Flight controller Fix wing and Multicopter

    Pixhawk 2.1 is an advanced autopilot system designed by the ProfiCNC and manufactured by HEX Technology. It features advanced processor and sensor technology from ST Microelectronics® delivering incredible performance, flexibility, and reliability for controlling any autonomous vehicle.

    Key Features of Pixhawk 2.1

        Triple redundant dampened IMU
        Heated system can be used in low temperatures
        ample I/O ports
        On-board battery backup for FMU and IO SRAM/RTC
        Separate power supplies for FMU and IO
        supports up to 3 GPS

    29 MEMS Sensors

        3x triple axis accelerometers
        3x triple axis gyroscopes
        3x triple axis magnetometers
        2x barometers

    Includes:

        The cube (installed) Pixhawk 2.1
        Full carrier board
        1 x standard power brick (upto 8s, 30A)
        Micro SD card (installed in Cube)
        Mounting tape and screws
        Cable Pack

    To take full advantage of the Pixhawk 2, Please add the new GPS with built in Safety switch, either Here, Here 2 or for RTK the Here+  switch.

    SKU: HX4-06001
    €279.00
    inc. VAT

     LOW STOCK
  • Pixhawk Cube & Here2 GNSS GPS Combo

    Pixhawk Cube & Here2 GNSS GPS Combo

    Cube & Here2 GNSS GPS Combo

    Pixhawk 2.1 ‘The Cube’ Combo Pack- This is a Pixhawk 2.1 Standard Suite and the Here 2 GNSS in one box, from time to time we may supply them in separate boxes depending on stock – the product is the same.

    Description:
    Pixhawk 2.1 is an advanced autopilot system designed by the ProfiCNC and manufactured by HEX Technology.
    It features advanced processor and sensor technology from ST Microelectronics®, delivering incredible performance, flexibility, and reliability for controlling any autonomous vehicle.

    Key Features of Pixhawk 2.1:

    • Triple redundant dampened IMU
    • Heated system can be used in low temperatures
    • ample I/O ports
    • On-board battery backup for FMU and IO SRAM/RTC
    • Separate power supplies for FMU and IO
    • supports up to 3 GPS

    29 MEMS Sensors in the cube

    • 3x triple axis accelerometers
    • 3x triple axis gyroscopes
    • 3x triple axis magnetometers
    • 2x barometers

    Includes:

    • The cube (installed) Pixhawk 2.1
    • Full carrier board (standard version)
    • Here 2 GNSS
    • 1 x standard power brick (upto 8s, 30A)
    • Micro SD card (installed in Cube)
    • Mounting tape and screws
    • Cable Packl advantage of the Pixhawk 2, Please add the new GPS with built in Safety switch.

    Here 2 Features:

    • Built in STM32F302 MCU running ChibiOS to enable user defined features and easy firmware updates
    • Adds 10DOF IMU sensor (ability to run its own EKF solution onboard the GPS module)
    • CANBUS support

     

    SKU: HX4-06057
    €375.00
    inc. VAT

     LOW STOCK
  • Pixhawk External LED and USB Module

    Pixhawk External LED and USB Module

    The module build in LED and USB on one board. You can use it to connect to Pixhawk. Use the provided four-position DF13 cables and connect to the I2C splitter module to set up a bright, multicolor LED and convenient USB port for your vehicle.

    Included in the set:

    • External USB module
    • External LED module
    • Two four-position DF13 cables (20 cm)
    SKU: PIXHLEDUSB
    €13.00
    inc. VAT

  • Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM MN8 GPS Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM MN8 GPS Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM MN8 GPS Combo for Multicopters

    The board integrates with PX4FMU+PX4IO
    Pixhawk is with new 32 bit chip and sensor technology

    Processor:
    32 bit 2M flash memory STM32F427  Cortex M4, with hardware floating point processing unit
    Main frequency: 256K, 168MHZ RAM
    32 bit STM32F103 backup co processor

    Sensor:
    L3GD20 3 axis digital 16 bit gyroscope
    LSM303D 3 axis  14 bit accelerometer /magnetometer
    MPU6000 6 axis accelerometer / magnetometer
    MS5611 high precision barometer

    Interface:
    5* UART, 1*compatible high voltage, 2*hardware flow control
    2*CAN
    Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
    Futaba SBUS compatible input and output
    PPM signal input
    RSSI (PWM or voltage) input
    I2C
    SPI
    3.3 and 6.6VADC input
    External USB MICRO interface

    Features:
    Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
    Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
    Provide redundant power input and fault transfer function;
    14* PWM/ actuator output;
    Bus interface (UART, I2C, SPI, CAN);
    Provide automatic and manual mode;
    Color LED lamp;
    Multi tone buzzer interface;
    Micro SD to record flight data;

    Package included:

    • 1 x 2.4.8 Pixhawk main control  
    • 1 x Safety switch  
    • 1 x Flight control shell
    • 1 x Buzzer
    • 1 x 6pin to 6pin line  
    • 1 x 4Pin to  4Pin line
    • 1 x 3pin DuPont line
    SKU: Pixhawk-MN8
    €169.00
    inc. VAT

    
  • Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters- NO GPS

    The board integrates with PX4FMU+PX4IO
    Pixhawk is with new 32 bit chip and sensor technology

    Processor:
    32 bit 2M flash memory STM32F427  Cortex M4, with hardware floating point processing unit
    Main frequency: 256K, 168MHZ RAM
    32 bit STM32F103 backup co processor

    Sensor:
    L3GD20 3 axis digital 16 bit gyroscope
    LSM303D 3 axis  14 bit accelerometer /magnetometer
    MPU6000 6 axis accelerometer / magnetometer
    MS5611 high precision barometer

    Interface:
    5* UART, 1*compatible high voltage, 2*hardware flow control
    2*CAN
    Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
    Futaba SBUS compatible input and output
    PPM signal input
    RSSI (PWM or voltage) input
    I2C
    SPI
    3.3 and 6.6VADC input
    External USB MICRO interface

    Features:
    Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
    Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
    Provide redundant power input and fault transfer function;
    14* PWM/ actuator output;
    Bus interface (UART, I2C, SPI, CAN);
    Provide automatic and manual mode;
    Color LED lamp;
    Multi tone buzzer interface;
    Micro SD to record flight data;

    Package included:

    • 1 x 2.4.8 Pixhawk main control  
    • 1 x Safety switch  
    • 1 x Flight control shell
    • 1 x Buzzer
    • 1 x 6pin to 6pin line  
    • 1 x 4Pin to  4Pin line
    • 1 x 3pin DuPont line
    SKU: Pixhawk
    €129.00
    inc. VAT

    
  • Plastic Blade B

    Plastic Blade B

    Fits most co-axials, and esky.

    included- 3 pairs/6 blades

    SKU: EK1-0313
    €5.00
    inc. VAT

     LOW STOCK
  • Power Distribution Board 12ESC (PDB) with LED 100A

    Power Distribution Board 12ESC (PDB) with LED 100A

    This power distribution board is used to make your multicopter installation neater and safer.  With support for up to 100A, and 8 ESC this PDB can be used on almost any multicopter. In addition to providing simple power distribution for up to 8 ESC's this board also includes two built in voltage regulators (5V output and 12V output) that you can use to power your electronics/, LED's or FPV gear on your multicopter. Other great features include LED's built onto the board.

    Please note that this PDB does not come with any cables, you will need to solder your ESC, and battery connector to this board.
    PDB Specification

    •   Max ESC number - 12
    •   Working Current - 100A Max
    •   Outer Diameter - 77mm
    •   Inner Diameter - 40mm
    •   Max input voltage - 6S
    •   5V Regulated output (built in voltage regulator)
    •   12V Regulated output (built in voltage regulator)
    SKU: SKU48602
    €18.00
    inc. VAT

  • POWERZIP STRIP

    POWERZIP STRIP

    POWERZIP strip, 16mm wide, 1meter long

    Power tape, holding power is up to 50 kg!!, Double face transparent silicone tape ( red cover), excellent for installation of wires, wood, fiber, Gyro , Receiver and more..

    Its suitable for internal & external use it offers high adhesion to a wide variety of surfaces. It has superior 'wetting out' properties which increase the bonded surface area increasing the strength of the bond. It has excellent ageing properties and is resistant to U.V. light, abrasion, corrosion & moisture.
    Service temperature is -30°c - +80°c (continuous)/ +130°c (shorterm).


    SKU: RB-5367
    €5.00
    inc. VAT

     IN STOCK
  • Precision Aluminum Tail Gear Case

    Precision Aluminum Tail Gear Case

    Microheli Precision CNC Aluminum Tail Gear Case 130X (Square)(RED) MH-130X125S

    Quality CNC upgrade from microheli

    For the E-Flite Blade 130X
    SKU: MH-130X125S
    €26.00
    inc. VAT

     72HR STOCK
  • Precision Titanium Swashplate 130X

    Precision Titanium Swashplate 130X

    The Precision CNC Titanium Swashplate is designed to improve stability, durability and overall performance on the Blade 130 X helicopter.
    It's directly replaced the stock plastic swashplate and also allows pilots to use the Aluminum/Carbon Fiber Anti-Rotation Guide set MH-130X011 or MH-130X111 to re-position Anti-Rotation Pin for swashplate tilting linearly and precisely in all directions.
    The Precision CNC Titanium Swashplate is machined with high tolerance from aircraft aluminum 6061 to achive the best possible precision and using high quality selected main ball bearing to minimize any unwanted slops and plays between upper swash and lower swash.
    More than that, the Precision CNC Titanium Swashplate is technically re-engineered center ball in line with swash arm balls to allow swashplate tilting linearly and precisely which produces the most accurate and fast cyclic response and cyclic power on Blade 130 X flybarless head system.
    And yet, the Precision CNC Titanium Swashplate is designed using all threaded Titanium ball joins and Titanium anti-rotation pins to prevent wear and tear for long time use.
    It is thin profile, more tilt angle and very light weight 2.61gram on this version (only 0.57g heavier than stock plastic swashplate).
    The Precision CNC Titanium Swashplate design will bring the best overall performance and the stylish look to your Blade 130 X helicopter.
    SKU: MH-130X012
    €31.00
    inc. VAT

  • Pro Glow driver

    Pro Glow driver

    Glow plug wrench, features lightweight diamond cut grip with cap. Long reach, great for large engine heads and helicopters .Handle can be use to store glow plugs or screws and etc.

    SKU: HTPVA043
    €9.00
    inc. VAT

  • Professional Aerial dedicated HDMI adapter cable

    Professional Aerial dedicated HDMI adapter cable

    Professional Aerial dedicated HDMI adapter cable

    Full compliance with HDMI 1.4 specification design, and we are fully in accordance with the design of the differential signal lines, to achieve maximum signal isolation in the design sequence distribution lines, strong anti-interference, good color reproduction.

    Specification:

    • Aerial dedicated
    • length 18cm
    • weight 5 g
    • support 1920x1080p
    • specification compatible HDMI1.4a

    SKU: RCD1015
    €29.90
    inc. VAT

     LOW STOCK
  • Professional Aerial HDMI to AV module

    Professional Aerial HDMI to AV module

    RCD3015 is dedicated aerial HDMI to AV module.
    The camera can output HDMI signals into AV signals for connecting video transmission stations.

    Specification:

    • Support SONY NEX5, NEX5N, NEX5R, NEX5T, NEX6R, NEX7N, NEX7R, NIKON D90, D3X
    • Output video format 720x576 PAL standard
    • Two-channel stereo output audio format
    • Without a separate power supply, HDMI interface to take power directly from the operating current of 30mA
    • Weight 9 g
    SKU: RCD3015
    €48.90
    inc. VAT


Manufacturers