eRCMarket is a company located in belgium, selling over 9000 products, serving community of modelers worldwide.
we proud of our service, quality of products, competitive prices
8 points ( for 8 esc) distribution board 100A Connection Board for Multicopter |
40 AMPS esc , specially fit Multicopters, best to be loaded with SimonK soft Extremely low internal resistance Super smooth and accurate throttle linearity Safety thermal over-load protection Auto throttle shut down in signal loss situation Supports high RPM motors Power arming protection (prevents the motor from accidentally running when switched on) New advanced programming software
|
NAV Module x 1 UART 4Pin cable (to GPS) 200mm x1 I2C 4Pin cable (to FC) 100mm x1
Features: All GPS data available via the I2C bus to connect to 328P Multiwii FC A LED on board show GPS 3D Fix status ATMega 328P Microcontroller 2 Molex 1.25mm 4Pin socket for GPS receiver and FC 2 port for ISP and FTDI
Specification: Dimension: 20mmX30mm Height: 5mm Weight:2.4g/5g(include cable) Hole diameter: 3mm |
Nano Flip Quadcopter 2.4GHz RTF This fully assembled and ready to fly micro-quadcopter of about 10 cm is able to perform indoor arobatic aerial maneuvers (loop / flip), even in small rooms (office, bedroom ...). Pressing in the same time the trigger button on the 3D associated transmitter and moving the right stick even allows easy looping or flip. Suitable for beginner who are looking to learn thanks to the stability provided by its inbuilt 6 axis gyro.
Specifications:
Included items:
|
Prop Guard for the Nano Flip Quadcopter |
The popular Naze32 is here! Initially designed for use with small to mid-sized multirotor craft, it has become the go-to controller for a host of Multirotor projects and propheads.The Full board contains the additional magnetometer and barometer Board comes with pins-Not soldered. Features: Designed for use with small indoor or small to mid-sized outdoor multirotor craft, or as a standalone camera stabilizer, the Naze32 flight control is simple to setup, with configuration based on the familiar “MultiWii” software. Specifications:
Included:
|
The Acro Naze32 is one of the best flight controllers available for Multi-rotors.this board is Acro version and not including the Magnetometer and barometer This FC features an STM32 32-bit processor and comes in an acro version and and full version. The Naze 32 can be used in many different configurations (up to an octocopter). It also does FrSky Telemetry, Multiwii serial protocol, and can control a camera gimbal control. MCU:ST Microelectronics STM32F103 72-MHz ARM Cortex-M3 Note that returns on these are not accepted after soldering. Please plug the board into your computer BEFORE you solder it to check it works. |
Set of needle levers for ALL engines such as OS engines .With those levers it will be easier to adjust the engines by remembering visual position Set comes with 2 levers and screws supplied. Color can be Silver, Red,Blue (Your choice) |
Fits gas motors and can be used as Inline fuel line |
The neXt level of heli simming. We gave our rc Helicopter Flight Simulator the name neXt because it heralds the next evolution in the model flight simulator industry. THIS IS a download product, and you will receive a license details once payment completed. in case shipping cost will be charged, it will be directly refunded.
Download: http://www.cgm-online.com/rc-heli-simulator/_download.html |
Great for making your own lighted signs. Sheet comes as Square of 10x10cm , or Round shaped diameter of 8cm. Kit comes with 6-12 volt driver . Best is to connect Small lipo 2-3 cells, or attach to Balancer of large lipo and use 2-3s from this source. You can attach the sheet to Drone, heli, or on the boom and fly in the dark. Alternatively, Print your name, stick on the sheet and it will glow in the dark, turn on and you have a beautiful lighted sign! Pictures of the shapes can be seen in Detailed images. One driver can feed up to 3 sheets. Set include 1 Glowsheet and one Driver |
Complete set includes two (2) Hi-Lum contrasting glow wires of 1 meter long, and Double glow wire Driver.
|
High-intensity light wire that glows strong at night. |
Driver box from 7-12v . up to 3 Night Wires can be connected to this box, providing you with the best lumination for night flying. |
Use this handy convenient piston stopper to lock any glow engines piston in place for safe and easy flywheel or clutch removal. Make your work go faster with simply remove the glow plug from the engine, screw the Piston Stopper in place, and your piston and crankshaft will be locked into position. Made from high quality aluminum this piston stopper features a knurled grip for quick finger tightening. Plastic cap will prevent Scratching the piston. |
Nylon insert lock nuts are hex nuts that have a captive nylon washer mounted in their top to create a prevailing torque type lock nut. The undersized washer forms a compression grip that binds on the threads of the mating fastener to resist loosening. Nyloc Nut (Pack of 10) M3 Nylon Insert Lock Nuts A2 Stainless Steel
|
Our RTF Drones have been designed to meet RPAS regulations. Fits DGAC group S1-S2-S3
Needed to complete |
Openpilot CC3D EVO Flight Controller 32-bit Flexiport New Version (Straight pins) The CC3D boards is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot Ground Control Station (GCS) software.
Specs:
Included:
|
CC3D EVO Hardware Features:
Flexiport: This flightcontroller also offers an innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. OpenPilot tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. Sensors and Components:
Package Includes:
|
CC3D Hardware Features:
Flexiport: This flightcontroller also offers an innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. OpenPilot tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. Sensors and Components:
Package Includes:
|
Special Shape carbon paddels, for Microhelicopters.Those paddles come with locking mechanism to insude they will never move on your flybar.Set of 2 Pcs |
Fusuno canopies are made with highest quality resin and fiberglass material to provide strong but flexible canopies. It helps prevent cracks that is normally seen in other canopies that are using lower quality material. All paints and clear coat are automobile grade provide great look, Great design at bargain price |
PANASONIC 6LR61 EVOLTA 9V |
Pinion gear, Fits Robbe Millenium , Avaliable in 15 T. Makes perfect Ratio for 80-90 size motors. |
SAV AU TOP ! Je recommande vivement :) Mention spéciale pour Michel qui est très professionnel,...
Mr. PIERRE MOZART IJIRAN
Dealing with real engineer and owner who knows the market, product and knows to understand what...
Mathis Ferrier
Hi, I am from India and placed an order with no tracking option.. The parcel was not coming to...
Mr. RATNARAJ KANUNGOE
One of the best online customer services I have ever been in contact with! Received very fast...
Mr. Karl Azzopardi
Bonjour a tous J\'ai fait une commande jeudi 21 décembre et reçus le 26, emballage parfait ,...
coutriaux
Copyright © 2000-2019 eRCMarket. All Rights Reserved.