This is a special Heat Sink to cool down your VTX or ESC.
Reduce the temprature to keep your component safe.
Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)
Dont place it directly over the electronic components since it might shortcut
Material : Aluminum
Sizes 20 x 14 x 6mm
Weight: 2.3 gr
1 pcs included in package
This is a special Heat Sink to cool down your VTX or ESC.
Reduce the temprature to keep your component safe.
Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)
Dont place it directly over the electronic components since it might shortcut
Material : Aluminum
Sizes 24x25mm
Weight: 5.2gr
1 pcs included in package
This is a special Heat Sink to cool down your VTX.
Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)
Dont place it over the electronic components since it might shortcut
Material : Aluminum
Size 11x10x6mm
Weight: 1gr
1 pcs included in package
This is a special Heat Sink to cool down your VTX.
Video transmitters known to be hot due the small cooling surface.This heatsink is the solution to reduce the temperature of the VTX and keep it long life. just glue it over the VTX where the heat comes from and its done. glue must be heat conducting or just attach it well that it touching the hot surface of vtx (metal plate part)
Dont place it over the electronic components since it might shortcut
Material : Aluminum
Size 14x14x6mm
Weight: 1.1gr
1 pcs included in package
Avizar latest 40 amp 6s OPTO Brushless ESC, already programmed with special software 600hz providing perfect fit for Multicopter pancake multipole motors.
The Multicopter ESC is a special design for multi-copter aircraft, excellent control over throttle linearity. Wide voltage range can be configured to be compatible with a variety of brushless motors available on the market.
Special 600hz software is loaded on this ESC.
Continuous current: 40A
Instant current(10S): 60A
BEC type: N/A
BEC output: OPTO
Battery cell: Li-io/ Li-poly 2-6S
Weight :29g
Dimension L*W*H: 66*26*13mm- Perfect Fit to Sky hero arms 30mm.
3.5mm pre-soldered connectors for easy connections to Motors
This Battery Eliminator Circuit (BEC) is perfect for providing clean 5 or 6v power to your receiver, flight control board, LEDs or other low voltage equipment. Simply connect your 2-6s lipo to the input.
EMax BLHeli Series 12A ESC for Multicopters (ONESHOT Available) .Based on BLHeli firmware, further optimized to the perfect drive performance. Low-voltage protection, over-heat protection and throttle signal loss protection. Separate power supply for MCU and BEC, enhancing the ESC’s ability of eliminating magnetic interference.
Parameters of the ESC can be set via program card or transmitter.
Throttle range can be set to be compatible with different receivers.
Equipped with built-in linear BEC or switch BEC.
Max speed: 210,000 rpm for 2-pole, 70,000 rpm for 6-pole, 35,000 rpm for 12-pole.
Emax 12a ESC SimonK Series Speed Controller Perfect for the 250 and 300 Size Fpv Racers. Superb esc that provides lightning fast throttle response which is ideally suited to the FPV Racing Quadcopters. The perfect ESC for your 250 quad race project.
One of the most Favorite ESCs finally got an upgrade! With this ESCs brand new F396 MCU processor, it is able to handle the higher RPM motors with ease. The processor on this ESC runs nearly twice as fast as the previous version, 48Mhz. It has also been equipped with a bit more flash memory and RAM. Designed to be compact and lightweight, this may be the perfect choice for many of the FPV Racers and Acro flyers! Thrust results to come. One of the smallest ESCs on the market for its size but can keep up with the bigger brothers. FVT LITTLEBEE 20A PRO ESCs supports 2-4s lipos, are mosfet driven and with fast, dedicated driver chips on a high quality PCB.
FVT LittleBee 30A ESC BLHeli OPTO 2-6S Supports OneShot125 For RC Multirotors.New 30A version of the famous FVT Little Bee ESC, the BLheli speed controller of choice for high-performance power and reliability. These ESCs arrive factory-flashed with BLheli firmware with OneShot125 and active braking support. The 30A variant supports a continuous current of 30 amps and bursts of 40A and yet still retains tiny dimensions for its class.
Multi - Littlebee 30A ESC, small size, light weight, fast response, support 2-6SLIPO, also supports Light Damped, is the best Mini multi axis power transfer
The UBEC is an external switching mode DC-DC regulator; it draws the DC voltage from 2-6S Lipo battery, drops it to a voltage level that is suitable for receivers and other electronic devices, and keep providing the stable current output up to 10Amp. As the UBEC has such a powerful output capability, so it is particularly applicable for large helicopters and fixed-wing aircrafts.
Specifications:
Input Voltage: 6V-25.2V (2-6S LiPo)
The output voltage is programmable by dip switches. 4 Options: 5.0V/6.0V/7.4V/8.4V
The 3A-UBEC is a switch mode DC/DC regulator, it outputs a consistent safe voltage for the receiver, gyro and servos.
It is very suitable for RC helicopter and other RC models especially when the built-in BEC in the speed controller has a very limited output capability.
Specification:
Output Voltage: 5V@3A or 6V@3A (Selectable by using a jumper connector)
Continuous output current: 3 Amps
Input: 5.5V-26V (2-6S Lipo or 5-18 cells NiMH /NiCd)
Size: 43mm*17mm*7mm (L*W*H)
Weight: 11g
Features:
Uses an advanced switch mode DC-DC regulator IC.
The output is powerful enough even working with 4S to 6S Lipo battery.
Battery polarity reversal protection.
A metal shield and a filter significantly reduce the electromagnetic interference.
The working status is shown by an LED, it lights when the UBEC works normally.
Hobbywing has released XRotor 40AInternational Version B 30901001 under Drone System category
Rapid Throttle Response
Dedicated program for multi-rotor ESCs, which is better than various
open-source programs, greatly improves throttle response.
Easy to Use
All settings except the "Timing (adjustable between High and Intermediate)"
are preset, making usage simple, highly intelligent and adaptive.
Less Signal Interference
The twisted-pair throttle signal cable effectively reduces interference produced
in signal transmission and makes flight more stable and reliable.
Super Low Internal Resistance
Good quality MOSFETs utilized by this XRotor 40A ESC make
internal resistance low but current endurance high.
Super High Throttle Signal
Compatible with various flight-control systems and supports a
throttle signal frequency of up to 621Hz.
Hobbywing XRotor Micro BLHeli 35A 3-6S F396 ESC Support OneShot125 w/ Wires for FPV Racing
Features:
Super Small & Light:
ESCs with incredible small size and light weight are specially designed for competition FPV drones
Quality components:
F396 48MHz MCU, 3-in-1 drive IC, High quality MOSFETs
BLHeli firmware ready:
Users can flash or upgrade the BLHeli firmware via the signal cable (on ESCs), and program 4 ESCs simultaneously after connecting their flight controller to the BLHeliSuite software if the flight controller uses the CleanFlight firmware
Damped Light Mode & OneShot125 Mode Supported:
Damped light mode improves the motor retardation and allows users to brake the FPV drones more efficiently. Active-freewheeling, technology improves driving efficiency, flight time and heat dissipation. The ESCs support OneShot125 high speed throttle, signal and regular throttle signal (within 500Hz) modes
Twisted-Pair Signal Cable Reduces Interference:
Effectively reduces interference produced in signal, transmission and makes the flight much more stable and reliable
Specification:
Brand: XRotor
Product Name: XRotor micro 35A BLHeli
Cont./Peak Current: 35A/50A
LiPo Cells: 3-6S LiPo
BEC Output : NO
DEO: Not Supported
OneShot Mode: Supported
Timing: Supported
Light Color: Not Supported
Motor Rotation: Supported
Throttle Range Calibration: Supported
Stick Programming: Stick Programming/BLHeliSuite
Size(mm)L*W*H: 36.5x16.7x5.5mm
Weight: 9.5g
Applications: FPVs with 150-330mm Diagonal Wheelbase
The Hobbywing XRotor 40Amp Multi-Rotor Brushless ESC is a great choice for 550/650 Class Multirotors. With quadcopter optimized software and programmable timing, this easy to use ESC provides stable flight characteristics that make it perfect for custom builds.
Features
Special core program for multi-rotor controllers greatly improves throttle response.
Specially optimized software for excellent compatibility with disc-type motors.
All settings except the timing are preset, making usage simple, highly intelligent and adaptive.
The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable.
Compatible with various flight-control systems and supports a signal frequency of up to 621Hz (Note: all throttle signals over 500Hz are non-standard signals)
Special drive chip has much better MOSFET driving effect than common driving circuit consisted of discrete components.
MOSFET with extra-low resistance brings high performance and great current endurance.
Specifications
Constant Current : 40 A
Peak Current : 60 A (10 Seconds)
BEC : No BEC
Lipo : 2-6S
Programmable Item :Timing (High/Intermediate)
Weight : 32gram
Size : 56.0x25.2x12.4mm
Avizar latest HVSK-40A High Voltage OPTO Brushless ESC, already programmed , V2 version. Be aware now its black colored shrink. if you have V1, it will not be compatible as mixture, you must use V1 or V2 for all of them
The Multicopter ESC is a special design for multi-copter aircraft, excellent control over throttle linearity. Wide voltage range can be configured to be compatible with a variety of brushless motors available on the market.
Output: Continuous 40A, Burst 60A up to 10 seconds
Input Voltage: 2-6cells lithium battery
BEC: NO BEC
Refresh rate of the throttle signal: at least 400Mhz
Timing: High or Intermediate
Red Black cable length: 120mm
Signal cable length: 260mm
Bullet Connector: 3.5mm
Size: 68 x 25 x 8.7mm
Weight: 26g
Features
Special core program for multi-rotor controllers greatly improves throttle response
Specially optimized software for excellent compatibility with disc-type motors
Settings are preset, making usage simple, highly intelligent and adaptive
The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable
Compatible with various flight-control systems and supports a signal frequency of up to 621Hz (Note: all throttle signals over 500Hz are non-standard signals)
MOSFET with extra-low resistance brings high performance and great current endurance
The clocked voltage regulator HiCopter is as a power supply for accessories (camera gimbal ...) used to Multikoptern.
This voltage regulator may be powered by batteries from 4S to 10S Li-XX cells and is suitable for use with peak currents of up to 12A.
Technical specifications:
Weight: 29g
Dimensions: 60x28x10mm
Operating temperature: -20 ... + 85 ° C
Number of cells: 4 - 10s Po or 12-33 NiXX
Ausgngsspannung: 12V
Pulse current 12A / 5sec
Maximum continuous current depends number of cells used:
Speed controllers of HiCOPTER product line are aimed for controlling and regulating BLDC motors that are used for driving multicopters. These controllers are pre-set from the manufacturer for the cooperation with stabilization systems used in copters. The controllers accept control signal with a frequency up to 500Hz and they respond to the needed change of revolutions from control/stabilization unit of the copter.
HiCOPTER speed controllers have control signal galvanically (optically) separated from flight battery. HiCOPTER speed controllers do not allow setting any paramaters. Brakes of the controllers are generally switched off, cut-off voltage is at the lowest possible level (depending on a type) and the timing of motor is set by the speed controller automatically. Potential change in the direction of rotation can be done by exchange of any two phase cables.