Motor Accessories

Motor Accessories

Accessories for Brushless motors, mounts, prop adaptors, and more

Products


  • Radial Mount

    Radial Mount

    Radial Mount for motors with 3mm shaft

    SKU: KRF916
    €12.00
    inc. VAT

     IN STOCK
  • Scorpion HK-3026 Bearing Maintenance Kit

    Scorpion HK-3026 Bearing Maintenance Kit

    The Scorpion HK-3026 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HK-30 Series Motor.

    SKU: HK-3026-M-Kit
    €19.99
    inc. VAT

     IN STOCK
  • Scorpion HK-40 Motor Bearing Kit

    Scorpion HK-40 Motor Bearing Kit

    Scorpion HK-40 Motor Bearing Kit.


    In order to keep your motor in top running condition, you need a good set of bearings. Occasionally, after a crash or landing in the dirt, the bearings can become damaged and need to be replaced.
    The Scorpion HK-40mm Motor Bearing Kit includes a pair of original equipment replacement bearings to fit the Scorpion HK-40 & HKIII-40 Series motors.(Except HK-4015)

    Please note, the bearings are an exact fit into the motor housings, so they do fit snugly. When removing the old bearings, you may need to gently tap them out. However, when installing the new bearings, do not tap them in with anything, as this can dent the ball races and ruin the bearings.
    When installing ball bearings they need to be pressed in by the outer part of the race. Never apply pressure to the inner race, as this can damage the bearing and lead to premature failure.

    SKU: HK40Bearing
    €8.50
    inc. VAT

     IN STOCK
  • Scorpion HK-5020 Motor Shaft Kit (6mm 43mm)

    Scorpion HK-5020 Motor Shaft Kit (6mm 43mm)

    The Scorpion HK-5020 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-5020 series Scorpion Helicopter Motors.

    The shaft for the HK-5020 series motors measures 10mm in diameter, and is 84.6mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    SKU: HK_5020_shaft
    €42.99
    inc. VAT

     IN STOCK
  • Scorpion HKII-2221 Bearing Maintenance Kit

    Scorpion HKII-2221 Bearing Maintenance Kit

    The Scorpion HKII-2221 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HKII-22 Series Motor.

    SKU: HK-2221-BM-Kit
    €19.99
    inc. VAT

     IN STOCK
  • Scorpion HKIII-4025 Shaft Kit XL (6mm)

    Scorpion HKIII-4025 Shaft Kit XL (6mm)

    The Scorpion HK-4025 & HKIII-4025 series motors are built with 8mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4025 & HKIII-4025 series Scorpion Helicopter Motors.

    This shaft kit is for the HK-4025 & HKIII-4025 series motors that used in newer T-600 Heli. It measures 8mm in diameter, and is 88.5mm in length. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 6mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    Included in the Box:

    • HKIII-4025 Motor Shaft Kit (6mm) -XL x1
    • Washer x 1
    • C-Clip x 2
    SKU: HK-4025-6mm-Shaft-XL
    €16.00
    inc. VAT

     LOW STOCK
  • Scorpion HKIII-4035 Bearing Maintenance Kit

    Scorpion HKIII-4035 Bearing Maintenance Kit

    The Scorpion HK-4035 Bearing Maintenance Kit is made by air craft grade aluminum, it provides an easiest and quickest way to Disassemble the Scorpion HK-40 & HKIII-40 Series Motor, except the HK-4015 Series.

    SKU: HK-4035-BM-Kit
    €19.99
    inc. VAT

     LOW STOCK
  • Scorpion Motor Bearing Lubrication Kit

    Scorpion Motor Bearing Lubrication Kit

    The Scorpion Motor Bearing Lubrication Kit will help you maintain the bearings in your Scorpion brushless electric motor. Today's brushless motors, especially the helicopter motors, can be pretty hard on the bearings. In an average flight, the motor in a 450 size helicopter spins around almost a quarter million times! Without proper lubrication, the balls in the bearings can wear out quickly, leading to premature failure. At these speeds, the oil can get thrown out of the bearings in as little as 10-15 flights. Once the bearings loose their lubrication, they can heat up and wear out very quickly. A small drop placed on each bearing about once every 10-15 flights is enough to maintain proper lubrication to insure the longest possible life for your motor bearings.

    The oil included in this kit contains everything necessary to keep your motor bearings in top condition. The specially designed oil not only lubricates, it also bonds to the metal parts, displaces moisture and prevents corrosion to extend the life of your motor bearings.

    The oil is safe for use on Acrylics, Polyester, Nylon, Vinyl, Delrin, Teflon, Formica, Polyethylene and Polypropylene. It is also safe on most painted surfaces. There is no visible effect on Buna-N, Viton or Neoprene rubber products, so it is safe around most fuel lines, O-rings and other rubber products.

    The Scorpion Motor Bearing Lubrication Kit contains a 30ml bottle of bearing lubricant, a leak-proof twist-on cap, and a needle point applicator (19.5mm in length, 1.3mm in diameter) with protective cover.

    SKU: Lubrication_Kit
    €8.00
    inc. VAT

     IN STOCK
  • Scorpion Motor HK-4525 Shaft Kit XL (6mm 50mm)

    Scorpion Motor HK-4525 Shaft Kit XL (6mm 50mm)

    The Scorpion HK-4525 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4525 series Scorpion Helicopter Motors.

    This extended shaft for the HK-4525 series motors measures 10mm in diameter, and is 104mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    SKU: HK_4525_shaft_50
    €29.00
    inc. VAT

     LOW STOCK
  • Scorpion motor HK-4530 Shaft Kit XL (6mm 37mm)

    Scorpion motor HK-4530 Shaft Kit XL (6mm 37mm)

    The Scorpion HK-4530 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4530 series Scorpion Helicopter Motors.

    The shaft for the HK-4530 series motors measures 10mm in diameter, and is 100mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    SKU: HK_4530_6mm_37
    €38.00
    inc. VAT

     IN STOCK
  • Scorpion motor HK-4530 Shaft Kit XL (6mm 55mm) Logo 700

    Scorpion motor HK-4530 Shaft Kit XL (6mm 55mm) Logo 700

    The Scorpion HK-4530 motors are built with 10mm hardened steel shafts that will last through countless hours of flying fun, but occasionally, on a "Less than Perfect" landing, you may bend or break one. For these occasions, we offer factory replacement shafts for all the HK-4530 series Scorpion Helicopter Motors.

    This extended shaft for the HK-4530 series motors measures 10mm in diameter, and is 117mm in long. The pinion end of this shaft is ground down to 6mm to allow the user to install 6mm pinion gears. The shaft kit will also fit other brushless motors that require a 10mm shaft of this length. The shafts can be cut shorter with a Dremel tool and a cut-off wheel if necessary to fit other motors.

    Note: The shafts in the Scorpion motors are a slight press fit into the aluminum front housing. The shafts will not just slide out when the setscrews are removed. They need to be pressed out in a bearing press, or in a drill press, with the front housing of the motor supported in a block of wood to prevent warping the front housing.

    SKU: HK_4530_6mm_55
    €38.00
    inc. VAT

     IN STOCK
  • Spur gear

    Spur gear

    Spur gear for SUPER Gear box- :68/ 76T
    SKU: KRF921-1
    €4.00
    inc. VAT

     IN STOCK
  • Spur gear

    Spur gear

    Spur gear for ALU Gear box : 60T/62/64/66T
    SKU: KRF922-1
    €6.00
    inc. VAT

     IN STOCK
  • Step Down regulator

    Step Down regulator

    Tail Servo Step-Down Voltage is ideally designed to step-down a voltage source of 6 volts that is outputted from any external BEC (battery eliminator circuit) down to 5.1 volts.

    This allows an external 6 volt BEC to be used with digital servos that are not capable of handling 6 volts. The Tail Servo Step-Down Voltage is equipped with male/female servo plugs and is ideally used in series with the RC model’s gyro and rudder servo to prevent any harmful damage or overloading to your servo. The Tail Servo Step-Down Voltage can also be used with any other applications that require a step down power voltage of approximately 0.8 volts

    SPECIFICATIONS:

    Height ----- 4 mm
    width ----- 8 mm
    Length ----- 12 mm
    Weight ----- 4 grams

    High power component to withstand current of up to 5 Amps continuous, 10 Amps peak.
    Prevents harmful damage and overloading to the digital rudder/tail servo.
    plug and play Easy installation

    SKU: WRL-STVR
    €4.00
    inc. VAT

     IN STOCK
  • SUPER Gear box

    SUPER Gear box

    SUPER Gear box-ratio:3.78:1 / 5..43
    SKU: KRF921
    €31.97
    inc. VAT

     IN STOCK
  • Switch & Fuel dot

    Switch & Fuel dot

    Single Switch with Fuel Dot in an aluminum housing.

    This item features a single switch with charge jack and a single fuel dot - with heavy duty 22AWG silicone wire.

    These switches are made of CNC aluminum with high quality switch hardware. All controls are at a touch of your fingers and can be easily installed behind a hidden door on the aircraft.
    Designed for longevity, these are anodized and designed to las
    t.

    SKU: SKU46416
    €19.00
    inc. VAT

     LOW STOCK
  • Tiger Motor T-Motor M6 CCW Prop Adapter Set for MN4010 MN4012 MN4014

    Tiger Motor T-Motor M6 CCW Prop Adapter Set for MN4010 MN4012 MN4014

    Tiger Motor T-Motor M6 CCW Prop Adapter Set for MN4010 MN4012 MN4014

    SKU: TMPAM6
    €12.00
    inc. VAT

     LOW STOCK
  • Tiger Motor T-Motor M8 CCW Prop Adapter Set for MN4010 MN4012 MN4014

    Tiger Motor T-Motor M8 CCW Prop Adapter Set for MN4010 MN4012 MN4014

    Tiger Motor T-Motor M8 CCW Prop Adapter Set for MN4010 MN4012 MN4014

    SKU: TMPAM8
    €12.00
    inc. VAT

     IN STOCK
  • Ultra Cooling Heatsink 28mm

    Ultra Cooling Heatsink 28mm

    Ultra Cooling Heatsink Avaliable in Diameter of 28 mm

    SKU: KRF914
    €8.00
    inc. VAT

     IN STOCK
  • Xnova Spare Shaft 4020 type A

    Xnova Spare Shaft 4020 type A

    Xnova Spare Shaft 4020 type A
    SKU: XN4020-6-36-A
    €7.90

     LOW STOCK
  • Xnova Spare Shaft 4020 type B

    Xnova Spare Shaft 4020 type B

    Xnova Spare Shaft 4020 type B
    SKU: XN4020-6-22-B
    €7.90

     LOW STOCK
  • Xnova Spare Shaft 4035 type A

    Xnova Spare Shaft 4035 type A

    Xnova Spare Shaft 4035 type A
    SKU: XN4035-6-41-A
    €7.90

     LOW STOCK
  • Xnova Spare Shaft 4535 type A

    Xnova Spare Shaft 4535 type A

    Xnova Spare Shaft 4535 type A
    SKU: XN4535-6-41-A
    €7.90
    inc. VAT

     LOW STOCK
  • Xnova Spare Shaft 4535 type C

    Xnova Spare Shaft 4535 type C

    Xnova Spare Shaft 4535 type C
    SKU: XN4535-8-61-C
    €7.90
    inc. VAT

     LOW STOCK

Manufacturers

Back