Jeti

Jeti

 Producer of Radios, Telemetry in Czech republic.

Products


  • Jeti hand transmitter DS-12 multimode RED

    Jeti hand transmitter DS-12 multimode RED

    Jeti hand transmitter DS-12 multimode RED

    A handy transmitter, high-quality construction with plastic housing, a large color display, ball bearing stick units and wear-free Hall sensors. A light weight, the quality design of the housing and a great ergonomic features of this transmitter. The software can be extended to your own preference and of course here JETI offers the full telemetry capabilities.
    expected equipment, stand in February 2019 :

    • Channels: 8 (up to 12 expandable)
    • 2.4GHz RF modules: 1
    • 900MHz backup system: Optional
    • Color TFT: 3.5 inch, 320x240 pixels
    • Stick units with Hall sensors: Yes
    • Resolution stick: 4096
    • Internal memory: SD card, 8GB
    • Free mixers: 5 (up to 20 expandable)
    • Stopwatches: 3 (up to 20 expandable)
    • Values ​​on display represented: 10 (up to 40 expandable)
    • (Expandable up to 20) 5: Spachausgabe for functions
    • Alarms: 10 (up to 40 expandable)
    • Channels for gyroscopic axes: 1 (up to 3 expandable)
    • Phases of flight: 3 (up to 6 expandable)
    • Flight phase trims: Yes
    • DITEX telemetry values: 16
    • Lua extensions: max. 10
    • MP3 player: Yes
    • Microphone: Yes

    Optional equipment, stand in February 2019 :

    • Logical switches: 0 (up to 16 expandable)
    • Sequencer: 0 (up to 6 expandable)
    • Motion sensor: optional
    • Audio Player: optional
    • Telemetry transmitter: 0 (up to 16 expandable)
    • Vibrate: optional
    • Speech: optional
    • Power Balancer: optional
    • Function curves: optional
    • Gas Limiter: optional
    • Variometer: optional
    SKU: JDEX-TDS12-MMR
    €579.00
    inc. VAT

  • JETI HiCopter BEC 12V3A

    JETI HiCopter BEC 12V3A

    JETI HiCopter BEC 12V3A

    The clocked voltage regulator HiCopter is as a power supply for accessories (camera gimbal ...) used to Multikoptern.
    This voltage regulator may be powered by batteries from 4S to 10S Li-XX cells and is suitable for use with peak currents of up to 12A.
     
    Technical specifications:

    • Weight: 29g
    • Dimensions: 60x28x10mm
    • Operating temperature: -20 ... + 85 ° C
    • Number of cells: 4 - 10s Po or 12-33 NiXX
    • Ausgngsspannung: 12V
    • Pulse current 12A / 5sec

    Maximum continuous current depends number of cells used:

    • At 4 cells LiPo: 4.7A
    • At 5 cells LiPo: 4.4A
    • With 6-cell LiPo: 3.9A
    • At 7 cells LiPo: 3.7A
    • 8 cells LiPo: 3.3A
    • In 9-cell LiPo: 3.3A
    • At 10 cells LiPo: 2.7A
    SKU: J-HIC-12V8A
    €144.00
    inc. VAT

     72HR STOCK
  • Jeti HiCopter ESC 70A opto

    Jeti HiCopter ESC 70A opto

    Jeti HiCopter 70A opto ESC

    Speed controllers of HiCOPTER product line are aimed for controlling and regulating BLDC motors that are used for driving multicopters. These controllers are pre-set from the manufacturer for the cooperation with stabilization systems used in copters. The controllers accept control signal with a frequency up to 500Hz and they respond to the needed change of revolutions from control/stabilization unit of the copter.
    HiCOPTER speed controllers have control signal galvanically (optically) separated from flight battery. HiCOPTER speed controllers do not allow setting any paramaters. Brakes of the controllers are generally switched off, cut-off voltage is at the lowest possible level (depending on a type) and the timing of motor is set by the speed controller automatically. Potential change in the direction of rotation can be done by exchange of any two phase cables.

    Specification:
     

    • Weight [g]    45
    • Dimensions [mm]    70 x 26 x 11
    • Sustained current [A]    70
    • Telemetry    No
    • Operational temperature [°C]    -20 ... 85
    • Supply Voltage [V]    5 ... 25,2
    • Batteries NiXX    6 ... 16
    • Batteries LiXX    2 ... 6
    • Batteries LiFe    2 ... 7
    SKU: J-HIC-70-O
    €75.00
    inc. VAT

     LOW STOCK
  • Jeti Joystick grips for DS Transmitter

    Jeti Joystick grips for DS Transmitter

    Jeti Joystick grips for DS Transmitter

    SKU: JMS-DS-SS
    €15.90
    inc. VAT

     LOW STOCK
  • Jeti MSpeed EX speed sensor

    Jeti MSpeed EX speed sensor

    MSPEED EX is a sensor which measures the speed of a flying model through the air to provide the indicated airspeed (IAS). The reporting of airspeed can be very instructive with regard to the control of a flying model, for example allowing the pilot to determine the model´s stall speed and set an alarm to indicate when the model falls below this speed.

    Another function of the sensor is to allow the pilot to set a desired speed and a step above or below this speed at which an acoustic signal should be sounded by the transmitter module. To facilitate easier reading of the indicated airspeed, a bar graph is displayed, marking the appropriate configured steps. The measurement of airspeed is based on the principle of change in dynamic pressure, measured by a Pitot tube, which is connected by silicon tubing. With the help of the wireless Duplex system, this sensor information can be reported to the pilot in realtime, allowing immediate feedback in airspeed changes and a deviations from the configured steps.

    Specifications:

    • Weight: 21gr
    • Dimensions: 22x25x13mm
    • Operational temperature: 0°C ... 85°C
    • Supply Voltage: 3,5V - 8,4V
    • Average Current: 10mA
    SKU: JEX-MS
    €74.90
    inc. VAT

     72HR STOCK
  • Jeti MSpeed EX speed sensor 450

    Jeti MSpeed EX speed sensor 450

    MSPEED 450 EX is a sensor which measures the speed of a flying model through the air to provide the indicated airspeed (IAS). The reporting of airspeed can be very instructive with regard to the control of a flying model, for example allowing the pilot to determine the model´s stall speed and set an alarm to indicate when the model falls below this speed.

    Maximum speed: 450km/h

    Another function of the sensor is to allow the pilot to set a desired speed and a step above or below this speed at which an acoustic signal should be sounded by the transmitter module. To facilitate easier reading of the indicated airspeed, a bar graph is displayed, marking the appropriate configured steps. The measurement of airspeed is based on the principle of change in dynamic pressure, measured by a Pitot tube, which is connected by silicon tubing. With the help of the wireless Duplex system, this sensor information can be reported to the pilot in realtime, allowing immediate feedback in airspeed changes and a deviations from the configured steps.

    Specifications:

    • Weight: 21gr
    • Dimensions: 22x25x13mm
    • Operational temperature: 0°C ... 85°C
    • Supply Voltage: 3,5V - 8,4V
    • Average Current: 10mA
    SKU: JEX-MS-450
    €87.90
    inc. VAT

     72HR STOCK
  • Jeti MT300 EX Temperature sensor

    Jeti MT300 EX Temperature sensor

    Designation of MT 300 EX Sensors are temperature measurements of devices like motors, controllers, batteries and other model accessories. Presentation of the measured data is realized by the JETIBOX terminal and the wireless information transfer is ensued with aid of the DUPLEX 2,4GHz system.

    The Duplex System takes advantage of the 2,4GHz-Band for communication which allows not only the transfer of remote control data to the model, but also in the opposite direction to the transmitter. The telemetric data measured during operation are transmitted in real time and the actual state of the data can be depicted on the JETIBOX LCD-display. The MT 300 EX unit records minimum and maximum temperatures of the individual sensors and delivers besides that their actual values.
    The JETIBOX terminal takes care of parameter adjustments as well as of indications of measured data.
    The MT 300 EX device consists of two parts. In the first instance of the MT module itself, which is recording the data measured by temperature sensors connected to the MT module, which on the other hand can be connected to the JETIBOX, to a receiver or to an Expander of the DUPLEX system. Keep an eye on the temperatures of the module and sensors in order not to expose them to temperatures higher than allowable – see technical data table.
    The MT 300 EX module allows triggering of acoustic alerts by the individual sensors. These alerts can report of temparature limit violations by too high or too low temperatures exceeding adjusted limits. The acoustic signal is generated by the transmitter module DUPLEX Tx which contains a small siren. The signals are differentiated by Morse codes in order to be able to distinguish between the individual types of alerts referring to individual sensors. The acoustic signalling of parameter violations will be generated even if there is no JETIBOX available. With a connected JETIBOX there will be an indication on its display showing which parameter has been violated. If several parameters have been violated at the same time the alert sounds change consecutively as well as the indications in the JETIBOX LCD-display.

    Specifications:

    • Weight: 6gr
    • Dimensions: 19x14x4mm
    • Operational temperature: -10°C ... 85°C
    • Supply Voltage: 3,5V - 8,4V
    • Average Current: 20mA
    • Number of temperature probes: 2
    • Range of measured temperature: -40°C ... 300°C
    • Accuracy of measurement: 1,5%
    SKU: JEX-MT-300
    €45.90
    inc. VAT

     LOW STOCK
  • Jeti MU3 EX 3-input voltage sensor

    Jeti MU3 EX 3-input voltage sensor

    The sensor MU-3 can be used for model on board monitoring of up to three voltages. With the aid of the MU-3 sensor the historical course of particular voltages can be monitored (minimum and maximum values) and the sensor may warn the user if set parameters are violated. Informations of the sensor are transmitted by the Duplex System to the user.

    The Duplex System utilizes the 2,4GHz band for communication, which not only transmits model controlling data to the model but also receives useful model data back at the transmitter end. Data collected during operation are transmitted in real time and the actual condition of measured values can be evaluated on the JETIBOX LCD display.

    Specifications:

    • Weight: 18gr
    • Dimensions: 36x20x5mm
    • Operational temperature: -10°C ... 85°C
    • Supply Voltage: 3,5V - 8,4V
    • Average Current: 8mA
    • Range of measured voltage A: 0 - 9V, B: 0 - 20V, C: 0 - 20V
    • Accuracy of voltage measurement: 1%
    SKU: JEX-MU3
    €37.90
    inc. VAT

     IN STOCK
  • Jeti Neck Strap for DC-16

    Jeti Neck Strap for DC-16

    Neck Strap for DC-16 - longer variant compared to DS-16 neck strap

    SKU: JMS-DC-NS
    €31.90
    inc. VAT

     72HR STOCK
  • Jeti Neck Strap for DS-16

    Jeti Neck Strap for DS-16

    Neck Strap for DS-16

    SKU: JMS-DS-NS
    €29.90
    inc. VAT

     72HR STOCK
  • JETI Power Ion RB 6200 7,2V

    JETI Power Ion RB 6200 7,2V

    JETI Power Ion RB 6200 7,2V

    Power-Ion accumulators 2600,2900 – 2S1P a 5200,5800, 6200 – 2S2P are battery packs suitable to power the receiver and servos in the model.

    The main advantages of Power-Ion accumulators include high mechanical resistance due to keeping  in a metal case. The accumulators are also characterized by a long cycle life. No balancer is needed for their operation and in case the current is higher than 150A, short circuit protection is activated. Overcharge protection is activated if the charging voltage is higher than 5V per cell. The accumulators are functional even at very low or very high temperatures (-10 - +60°C).

    Each pack is provided with one two-wire cable with the JR connector for charging and with one two-wire cable with the MPX connector for connection to the model. Both cables are of the same length.

    Specification:

    • Manufacturer:     Jeti
    • Voltage [V]:     7.2
    • Loading rate [C]:     2
    • Cell number (LiPo):     2
    • Maximum current [A]:     31
    • Discharge rate [C]:     5
    • Capacity [mAh]:     6200
    • Battery Type:     Li-Ion
    SKU: PI-RB-6200
    €72.90
    inc. VAT

     LOW STOCK
  • Jeti Power-Ion RX accumulators 2600 2S 7.2V

    Jeti Power-Ion RX accumulators 2600 2S 7.2V

    Jeti Power-Ion RX accumulators 2600 2S 7.2V

    Power-Ion accumulators 2600,2900 – 2S1P a 5200,5800 – 2S2P are battery packs suitable to power the receiver and servos in the model.

    The main advantages of Power-Ion accumulators include high mechanical resistance due to keeping  in a metal case. The accumulators are also characterized by a long cycle life. No balancer is needed for their operation and in case the current is higher than 150A, short circuit protection is activated. Overcharge protection is activated if the charging voltage is higher than 5V per cell. The accumulators are functional even at very low or very high temperatures (-10 - +60°C).

    Each pack is provided with one two-wire cable with the JR connector for charging and with one two-wire cable with the MPX connector for connection to the model. Both cables are of the same length.

    Specification:

    • Weight [g]     136
    • Dimensions [mm] 104 x 47 x 32
    • Sustained current [A]     20
    • Peak current (max 30s) [A] 40
    • Cell type     LiIon
    • Capacity [mAh]     2600
    • Rated voltage [V]     7.2
    • Max. cell voltage [V]     4.2
    • Max. battery voltage [V] 8.4
    SKU: PI-RB-2600
    €39.90
    inc. VAT

     LOW STOCK
  • Jeti Power-Ion RX accumulators 5200 2S 7.2V

    Jeti Power-Ion RX accumulators 5200 2S 7.2V

    Jeti Power-Ion RX accumulators 5200 2S 7.2V

    Power-Ion accumulators 2600,2900 – 2S1P a 5200,5800 – 2S2P are battery packs suitable to power the receiver and servos in the model.

    The main advantages of Power-Ion accumulators include high mechanical resistance due to keeping  in a metal case. The accumulators are also characterized by a long cycle life. No balancer is needed for their operation and in case the current is higher than 150A, short circuit protection is activated. Overcharge protection is activated if the charging voltage is higher than 5V per cell. The accumulators are functional even at very low or very high temperatures (-10 - +60°C).

    Each pack is provided with one two-wire cable with the JR connector for charging and with one two-wire cable with the MPX connector for connection to the model. Both cables are of the same length.

    Specification:

    • Weight [g] 230
    • Dimensions [mm] 104 x 47 x 50
    • Sustained current [A]     40
    • Peak current (max 30s) [A] 80
    • Cell type     LiIon
    • Capacity [mAh]     5200
    • Rated voltage [V] 7.2
    • Max. cell voltage [V]     4.2
    • Max. battery voltage [V] 8.4
    SKU: PI-RB-5200
    €55.90
    inc. VAT

     72HR STOCK
  • Jeti PPM DSC Socket (mono) for Jeti Duplex DC16 Transmitter

    Jeti PPM DSC Socket (mono) for Jeti Duplex DC16 Transmitter

    Jeti PPM DSC Socket (mono) for Jeti Duplex DC16 Transmitter

    SKU: JMS-DC-KPPM-B
    €9.90
    inc. VAT

     72HR STOCK
  • Jeti PPM DSC Socket (stereo) for Jeti Duplex DC16 Transmitter

    Jeti PPM DSC Socket (stereo) for Jeti Duplex DC16 Transmitter

    Jeti PPM DSC Socket (stereo) for Jeti Duplex DC16 Transmitter

    SKU: JMS-DC-KPPM-R
    €9.90
    inc. VAT

     72HR STOCK
  • Jeti RC DroidBox

    Jeti RC DroidBox

    Jeti RCDroidBox allows real-time monitoring and recording of telemetry data transferred using JETI Duplex or Duplex EX protocol. The system consists of both hardware and a software part. The hardware is the actual RCDroidBox Bluetooth adapter and the software is an application running on a device with the Android operating system, such as cell phone or tablet.

    The application is available free of charge on Google Play - JATAYA - RCDroidBox. For active use the RCDroidBox has to be connected to a battery 4V-15V with the correct polarity and to the Ext. connector of the RC transmitter or transmitter module.

    You can order the RCDroidBox device through one of our dealers in your region.

    Description of RCDroidBox and transmitter connection
    To make a successful instalation of the RCDroidBox, it is necessary to carry out following steps:

    Connect RCDroidBox Ext. connector to the Ext. connector of the transmitter module.
    Connect a separate battery power 4V-15V to the DroidBox power connector.
    Mechanically fasten the battery and the RCDroidBox to the transmitter.

    For connecting Bluetooth adapter and the transmitter module, 30cm connecting cable is delivered with the porduct. The polarity is indicated both on the side of the RCDroidBox, and on the side of the transmitter module. Select the power battery to your discretion. In the photo below NiMH 600 mAh 1/3 AA battery is used. Such a battery has a reasonable size for fitting to the RC transmitter, and the RCDroidBox will work approximately for 15 hours.

    For the whole system to function properly both your RC Transmitter and receiver must support JETI Duplex or JETI Duplex EX. The RCDroidBox and the RC transmitter must be connected together using the three-pin Ext. connector. The connector on the transmitter is the one which would otherwise be used for JETIBOX terminal. The correct orientation of the connector is depicted both on RCDroidBox and on the transmitter. The connection is realized using a three-wire cable with a standard servo -connector on both sides. A separate power supply from battery 4V-15V with the correct polarity and voltage needs to be connected to the RCDroidBox battery connector. The final component is the cell phone or tablet running both the operating system Android (2.3.3 or higher) and the RCDroidBox application.

    Specification:

    • Weight [g]    15
    • Dimensions [mm]    38 x 20 x 7
    • Operational temperature [°C]    -15 ... 50
    • Supply Voltage [V]    4 ... 15
    • Average Current [mA]    20
    SKU: JEX-MBT-JAT
    €89.90
    inc. VAT

     LOW STOCK
  • Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

    Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

    Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

    11 channel full-range receiver compatible with JETI EX & EX Bus
    protocols. Supports telemetry functions and contains a separate battery power connector.

    Additional features:

    • PPM
    • input (Sat1)

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM
    signal only. This PPM
    signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM
    signal at the input.

    DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

    Manuals - Duplex EX

    • JETI Duplex EX Receiver Manual V3.22 [EN, DE] - English & German user manual for the receivers version 3.22 (6/2014)
    • Declaration of Conformity CZ+EN - Standards compliance
    • JETI Duplex EX Manual V3.0 EN+DE - English & German user manual for Tx modules and receivers (6/2011)Rx + RSat Jetibox Schema V3.0 CZ - Jetibox screen schemes of the receivers and satellites
    • Rx + Rsat Jetibox Schema V3.0 EN+DE - Jetibox screen schemes of the receivers and satellites

    Update - Receivers

    • Duplex EX - Rx V3.22 - Rx Firmware Update (4/2014) - EX Bus
    • , Log. inputs/outputs, UDI. RSAT2[3.21]: By default, PPM
    • fail-safe is set to "Off". [3.22] Telemetry logical inputs improved.
    • Duplex EX - Rx & Tx V3.04 - Rx & Tx Compatibility Firmware Update (3/2012)
    • Duplex EX - Rx V3.11 - Rx Firmware Update (5/2013) - EX Bus
    • JETI Duplex EX Manual V3.11 EN - English user manual for receivers (4/2013)
    SKU: JDEX-R11EPC
    €107.90
    inc. VAT

     LOW STOCK
  • Jeti Receiver Duplex 2.4EX R5L 2,4GHz

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz

    5 channel full-range receiver compatible with JETI EX & EX Bus protocols. This receiver is designed for operation in small and medium models. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.
    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    DUPLEX  EX System is fully compatible with the previous version of the DUPLEX.

    Specification:
     

    • Quiescent current [mA]:    30
    • Receive Sensitivity [dBm]:    -106
    • Antenna number:    2
    • Antenna length [mm]:    100
    • Channels:    5
    • Satellite receiver possible:    
    • Real-time telemetry:    
    • Transmission power [dBm]:    15    
    • Type:    Duplex EX
    • Rated voltage up to [V]:    8.4
    • Rated voltage [V]:    3.2
    • Weight [g]:    5.4
    • Height [mm]:    7
    • Width [mm]:    20
    • Length [mm]:    47
    •  
    SKU: JDEX-R5L
    €63.90
    inc. VAT

     IN STOCK
  • Jeti Receiver Duplex 2.4EX R5L 2,4GHz W/antenna 20cm

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz W/antenna 20cm

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz W/antenna 20cm

    Programmable duplex 2.4EX 9 channel receiver 2.4GHz:

    • bi-directional communication with the transmitter
    • Transfer of the telemetry data to the transmitter (read out via the JETIBOX)
    • Receiver supply voltage indication at the transmitter, and adjustable value for triggering an alarm
    • a plurality of receivers to a transmitter possible receivable up to a total of 16 channels
    • adjustable Failsafe
    • Servo channels freely assignable
    • Servo travels, center position and duration adjustable
    • free mixers allocation of channels
    • Expo the channels can be set
    • Activation within a quarter second after switching
    • Connection for sensors (8 channel expander bix to 8 sensors)
    • programmable with the JETI Box directly or wireless via transmitter
    • light version for indoor models

    DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and compatible, of course, full of the previous components .
    The EX Series provides a significant extension of the possibilities for the transmission of telemetry data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor receive user-friendly design a better overview of the operational status of your model, facilitating the setting of the system components and the way an easier processing, imaging and analysis capability of the (recorded) flight data

    Specifications:

    • Dimensions 47x20x7mm
    • Weight     5.4 g
    • Antenna length     2x 200mm
    • Outputs 5
    • Temperature range -10 to + 85 ° C
    • Input voltage 3.2 - 8.4V
    • Average Power Consumption 30 mA
    • Real-time telemetry transmission Yes
    • Programming JETIBOX
    • Satellite receiver No
    • Transmission power 15 dBm
    • Receive Sensitivity -106 dBm

    Alarm settings:
    With the JETI Box alarm signals can be activated at (beeps by duplex RF module in the transmitter):
    Alarm waste Receiver supply below a set voltage value
    By connecting a current and voltage sensor to the receiver alarm can be triggered by:

    • Exceed a current value
    • Undershooting of a voltage value
    • Exceed a capacitance value

     

    SKU: JDEX-R5L-A20
    €65.90
    inc. VAT

     IN STOCK
    NEW
  • Jeti Receiver Duplex 2.4EX REX10

    Jeti Receiver Duplex 2.4EX REX10

    JETI Receiver Duplex 2.4EX REX10

    10 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

    Additional features:

    • PPM input
    • PPM output
    • Integrated expander for EX & EX Bus devices
    • UDI digital output

    JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
    The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
    The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers.
    For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
    The REX receivers are fully compatible with the previous generation of the Duplex equipment.

    Specification.

    • Weight [g] 16
    • Dimensions [mm] 51 x 28 x 11
    • Number of channels 10
    • Telemetry Yes
    • Operational temperature [°C]     -10 ... 85
    • Compatible protocols DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm] 2 x 200
    • Supply Voltage [V] 3,5 - 8,4
    • Average Current [mA] 75
    • Satellite receiver support Yes
    • Output Power [dBm] 15
    • Receiver Sensitivity [dBm] -106
    SKU: JDEX-RR10
    €103.90
    inc. VAT

     LOW STOCK
  • Jeti Receiver Duplex 2.4EX REX12

    Jeti Receiver Duplex 2.4EX REX12

    JETI Receiver Duplex 2.4EX REX12

    12 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

    Additional features:

    • PPM input
    • PPM output
    • Integrated expander for EX & EX Bus devices
    • UDI digital output

    JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
    The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
    The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers.
    For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
    The REX receivers are fully compatible with the previous generation of the Duplex equipment.

    Specification.

    • Weight [g] 24
    • Dimensions [mm] 51 x 28 x 11
    • Number of channels 12
    • Telemetry Yes
    • Operational temperature [°C]     -10 ... 85
    • Compatible protocols DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm] 2 x 400
    • Supply Voltage [V] 3,5 - 8,4
    • Average Current [mA] 75
    • Satellite receiver support Yes
    • Output Power [dBm] 15
    • Receiver Sensitivity [dBm] -106
    SKU: JDEX-RR12
    €124.90
    inc. VAT

     LOW STOCK
  • JETI Receiver Duplex 2.4EX REX6 Assist

    JETI Receiver Duplex 2.4EX REX6 Assist

    6 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

    The REX A receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multicopters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.


    Features:

    • Up to 16 stabilized airplane channels.
    • Support for different multicopter types – from tricopters to octocopters.
    • Up to 3 adjustable flight modes, options for stabilizing the horizon and altitude.
    • In-flight gain tuning using free channels.
    • Using the latest 3-axis gyroscope, 3-axis accelerometer and barometric altimeter.
    • Support for LED strip consisting of WS2812 chips.
    • Support for external camera gimbal driven by servos.
    • Intelligent fail-safe.
    • Vibration analysis.
    • Full set-up options with DC/DS transmitters or via PC.
    • Available telemetry: Receiver voltage, signal quality, G-force, attitude orientation.
    • Support of telemetry and up to 3 sensors connected directly.

    Specifications:

    • Weight [g]: 11
    • Dimensions [mm]: 38 x 25 x 11
    • Number of channels: 6
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 100
    • Supply Voltage [V]: 3,5 - 8,4
    • Average Current [mA]: 75
    • Satellite receiver support: Yes
    • Output Power [dBm]: 15
    • Receiver Sensitivity [dBm]: -106
    • Assist stabilization: Yes
    SKU: JDEX-RR6A
    €129.90
    inc. VAT

     72HR STOCK
  • JETI Receiver Duplex 2.4EX Rex7 Assist

    JETI Receiver Duplex 2.4EX Rex7 Assist

    7 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

    The REX A receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multicopters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.


    Features:

    • Up to 16 stabilized airplane channels.
    • Support for different multicopter types – from tricopters to octocopters.
    • Up to 3 adjustable flight modes, options for stabilizing the horizon and altitude.
    • In-flight gain tuning using free channels.
    • Using the latest 3-axis gyroscope, 3-axis accelerometer and barometric altimeter.
    • Support for LED strip consisting of WS2812 chips.
    • Support for external camera gimbal driven by servos.
    • Intelligent fail-safe.
    • Vibration analysis.
    • Full set-up options with DC/DS transmitters or via PC.
    • Available telemetry: Receiver voltage, signal quality, G-force, attitude orientation.
    • Support of telemetry and up to 3 sensors connected directly.

    Specifications:

    • Weight [g]:13
    • Dimensions [mm]: 42 x 28 x 11
    • Number of channels: 7
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 200
    • Supply Voltage [V]: 3,5 - 8,4
    • Average Current [mA]: 75
    • Satellite receiver support: Yes
    • Output Power [dBm]: 15
    • Receiver Sensitivity [dBm]: -106
    • Assist stabilization: Yes
    SKU: JDEX-RR7A
    €144.90
    inc. VAT

     72HR STOCK
  • Jeti Replacement Switch for DC-16: Long 2 Position

    Jeti Replacement Switch for DC-16: Long 2 Position

    Jeti Replacement Switch for DC-16: Long 2 Position

    SKU: JMS-DC-TSL2
    €13.90
    inc. VAT

     LOW STOCK

Manufacturers