Producer of Radios, Telemetry in Czech republic.
JETI DUPLEX 2,4EX Alu-Case for Transmitter DS-16 and DS-14
|
DUPLEX 2,4EX Transmitter-Battery Power Ion 5200 for Transmitter DC/DS |
The Jeti Duplex MUI 75 is a voltage and current telemetry sensor, compatible with all Jeti Duplex receivers and expanders, suitable for measuring currents up to 75A and voltages up to 60V. Using this sensor it is possible to view on your Jeti Box, the overall pack voltage, the motor run time and the capacity drawn from your flight battery as well as the present amp draw of your power system! You can also set alarms for:
This sensor should be connected between the power systems battery pack and the speed controller, in order to provide a pass-through to measure the current drain of your power set. Please note, the maximum current capability of this sensor is 75 amps. This sensor is not required to view the voltage and other metrics associated with the receiver system, which is provided by all Duplex receivers, without the need for an additional sensor. |
Jeti Duplex 2.4EX R18 receiver including RSat2 satellite receiver.
|
9 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.
|
Jeti Duplex 2.4EX R9 channel full-range receiver W/antenna 40cm Programmable duplex 2.4EX 9 channel receiver 2.4GHz: Bi-directional communication with the transmitter DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and compatible, of course, full of the previous components . Specifications:
Alarm settings:
|
JETI DUPLEX 2.4EX RC Switch |
Jeti Duplex 2.4EX Transmitter module TU2 EX DUPLEX TU2 EX module is suitable for all transmitters, especially for those with non-exchangeable HF plug-in modules. Installation is possible into almost all types of transmitters. There are only two main requirements: A transmitter with the possibility of operation in PPM DUPLEX TU2 EX module is an enhanced version DUPLEX TU2. Along with the mounting kit it simplifies mounting SWTU2 to the transmitters. An assembly set VOICE-1 may be better adapted to the acoustic properties after incorporation into the transmitter. Futaba: Hitec: Graupner: Multiplex: |
Jeti Duplex DS-14 transmitter preconfigured mode 1/3 The DS-14 represents Jeti's new, State-of-the-art, transmitter that sets a new quality standard for the RC Industry with its revolutionary features and brand new plastic Hall Sensor Gimbals. Jeti's final touches and finishes are outstanding. The front panel of the system is made of aluminum with UV stabilized clear coating and the case is made of painted, CNC cut, solid aluminum.
|
The DS-14 represents Jeti's new, State-of-the-art, transmitter that sets a new quality standard for the RC Industry with its revolutionary features and brand new plastic Hall Sensor Gimbals. Jeti's final touches and finishes are outstanding. The front panel of the system is made of aluminum with UV stabilized clear coating and the case is made of painted, CNC cut, solid aluminum.
|
6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors or by the external MPX connector. Antenna length: 40cm The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts. DUPLEX System EX is fully compatible with the previous version of the DUPLEX.
|
JETI Duplex R7 Nano Receiver Weight [g] 1 (2) Dimensions [mm] 30 x 18 x 5 Number of channels 7 Telemetry Yes Operational temperature [°C] -10 ... 85 Compatible protocols DUPLEX 2.4GHz EX, EX Bus Antenna Length [mm] 1 x 32 Supply Voltage [V] 3,2 - 8,4 Average Current [mA] 30 Satellite receiver support No Output Power [dBm] 6 Receiver Sensitivity [dBm] -98 |
Jeti Duplex receiver 2.4EX R18 2.4GHz + DRsat2 EX 18 channel full-range receiver compatible with Jeti EX & EX bus protocols. Support telemetry functions. Power supply is provided by MPX connector or standard JR connectors. Additional features: The DUPLEX EX line of receivers is Intended for surgery with DUPLEX Tx transmitter modules in the 2,4GHz band-and are fully compatible with the previous version of the DUPLEX. DUPLEX EX system is fully compatible with the previous version of the DUPLEX. Specification:
|
Jeti Duplex receiver 2.4EX REX3 with 20cm antenna DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and , of course, fully compatible with the existing components . Programmable Duplex 2.4EX REX3 receiver 2.4GHz:
|
Jeti Duplex receiver 2.4EX REX3 with 40cm antenna DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and , of course, fully compatible with the existing components . Programmable Duplex 2.4EX REX3 receiver 2.4GHz:
|
Jeti Duplex Satellite for 2.4EX Type2
|
Jeti Duplex Satellite for Type R.sub.sat 900 Only the DC 24 transmitter have a backup transmission system for the highest data transfer security and reliability. Specification:
|
Transmitter tray made of black acrylic for transmitters DC-16 |
Jeti Encoders long for DS Transmitter (2 pcs) |
Jeti Enlink 2RS EnLink 2RS is a device for increasing safety and reliability of radio controled models to the highest level. Parallel connection of systems that are detached maximally leads to the significant increase in reliability. EnLink2RS is constructed especially for installing to systems with parallel sorting of two receivers in the model. |
Exact information about the altitude and distance of a model in space are extremely important guidance elements for the pilot who is remote controlling the model. Thanks to the GPS satellite positioning system the MGPS sensor defines the exact model position and calculates speed, altitude and distance from the point of origin, furthermore the course, azimuth and the total covered distance.
|
Jeti Hand Pads for tray PCD-2 |
Jeti hand transmitter DS-12 multimode black A handy transmitter, high-quality construction with plastic housing, a large color display, ball bearing stick units and wear-free Hall sensors. A light weight, the quality design of the housing and a great ergonomic features of this transmitter. The software can be extended to your own preference and of course here JETI offers the full telemetry capabilities.
Optional equipment, stand in February 2019 :
|
Jeti hand transmitter DS-12 multimode Blue A handy transmitter, high-quality construction with plastic housing, a large color display, ball bearing stick units and wear-free Hall sensors. A light weight, the quality design of the housing and a great ergonomic features of this transmitter. The software can be extended to your own preference and of course here JETI offers the full telemetry capabilities.
Optional equipment, stand in February 2019 :
|
Dealing with real engineer and owner who knows the market, product and knows to understand what...
Mathis Ferrier
Super company. Extreme fast service!! Thanks a lot.
Ben
Even a complication is not a challenge for those guys, any modification, needs, questions: All...
Vladimir Abtrimov
Thank you for your fast delivery and competitive prices to the UK
Mr. MR M J HOYLE Hoyle
A fantastic store! Great service! The guys know their stuff and are realy enthusiastic of what...
Mr. Vlad Babenko
Copyright © 2000-2019 eRCMarket. All Rights Reserved.