Miniature Aircraft

Miniature Aircraft Famous producer of X-cell helicopters, Now made in germany

Products


  • Miniature Aircraft  Whiplash-Turbine II with TS 45iH and Blades - Kit version

    Miniature Aircraft Whiplash-Turbine II with TS 45iH and Blades - Kit version

    Miniature Aircraft  Whiplash-Turbine II with TS 45iH and Blades - Kit version.

    Please note: delivery time is 3-4 weeks

    Included in the kit

    •     Whiplash helicopter kit
    •     TS45i heli turbine engine, Whiplash special edition
    •     MS Composite special gasser / turbine main blades 710mm (exclusively made for MA)
    •     MS Composite 106mm tail blades

        Other equipment needed and not included:

    • Servos: 3x cyclic, 1x tail
    • FBL system which can handle the supersonics emitted by the turbine engine (Axon, CGY760R and others)
    • Governor, we highly recommend to use an external governor to control the head speed.use defects at the turbine engine
    • 2x 2S LiPo / LiFe batteries like 2S3500-4000 RX
    • 2x battery switch
    • Receiver
    • Telemetry module for the turbine engine (optional)

     Chassis:

        Sturdy graphite main frame unit.
        All C/F parts are made from high quality 100% carbon.
        Main frame designed for maximum protection of the turbine engine
        CNC machined Delrin 117 tooth helical main gear
        High quality one way bearing made in Germany
        High quality one way bearing hub, full ball bearing, made from stainless steel, hardened and ground
        Heavy duty, high quality front tail drive gears made in Germany
        High precise two-piece clutch bell with double ball bearing support
        Standard gear ratio for 710 to 720mm main blades, typ. head speed 1650 to 2000 rpm
        Optional gear ratios for 690 or 800mm blades
        True 6061-T6 CNC machined aluminum components
        CNC machined aluminum triple main shaft bearing blocks
        Direct controlled 120 (degree) CCPM
        CNC machined aluminum boom clamps
        CNC machined aluminum turbine engine mount
        CNC machined additional tubine engine front support
        Balanced fan and hub assembly
        Presinstalled magnets for governor
        Full ball bearings throughout
        High quality landing gear struts
        Large fuel tank for typical 5 to 7 minutes of flying time
        Prepared for optional twin tank system for longer flying time
        Additional header tank for bubble-free fuel supply of turbine (included)

    Rotor Head:

        Full ball bearings
        Heavy duty linkages
        9mm head axle made from special high quality steel
        CNC machined aluminum swashplate
        CNC machined main rotor grips
        CNC machined main rotor head
        High quality swashplate heim ball/ball bearing
        High precise swash plate follower arms with 4 ball bearings each


    Tail Rotor:

        Full ball/thrust bearings
        Tail Rotor hub made from special high quality steel
        Graphite tail fin
        CNC aluminum “open” gearbox
        CNC machined tail gears made from aluminum with hard anodizing surface and POM
        Aluminum 22mm tail boom
        Positive control system
        Hardened tail rotor output shaft
        High precise tail slider
        Carbon/Aluminum boom supports

    Turbine engine:

    Whiplash Special Edition two shaft kero-start turbine for R/C helicopters made by Turbine Solutions.

        Two shaft kero-start engine
        Gearbox output shaft rpm range: 4,000 to 15,000 rpm
        Max Power Output: 6.8 HP / 5Kw @ 190,000 rpm
        Max Torgue: 4Nm / 2.9 ft Lbs @ 13,500 rpm
        Fuel consumption: 176ml/Min / 5.8oz/Min

    Canopy:

        High Visibility Painted Epoxy-Glass Canopy

    Blades:

        MS Rapid 710 Gasser & Turbine Main Blades
        MS 106 Tail Blades

    SKU: MA1035-1
    €6492.00
    inc. VAT

     72HR STOCK
  • Miniature Aircraft  Whiplash-Turbine No engine - Kit version

    Miniature Aircraft Whiplash-Turbine No engine - Kit version

    Miniature Aircraft  Whiplash-Only Heli kit

     Chassis:

        Sturdy graphite main frame unit.
        All C/F parts are made from high quality 100% carbon.
        Main frame designed for maximum protection of the turbine engine
        CNC machined Delrin 117 tooth helical main gear
        High quality one way bearing made in Germany
        High quality one way bearing hub, full ball bearing, made from stainless steel, hardened and ground
        Heavy duty, high quality front tail drive gears made in Germany
        High precise two-piece clutch bell with double ball bearing support
        Standard gear ratio for 710 to 720mm main blades, typ. head speed 1650 to 2000 rpm
        Optional gear ratios for 690 or 800mm blades
        True 6061-T6 CNC machined aluminum components
        CNC machined aluminum triple main shaft bearing blocks
        Direct controlled 120 (degree) CCPM
        CNC machined aluminum boom clamps
        CNC machined aluminum turbine engine mount
        CNC machined additional tubine engine front support
        Balanced fan and hub assembly
        Presinstalled magnets for governor
        Full ball bearings throughout
        High quality landing gear struts
        Large fuel tank for typical 5 to 7 minutes of flying time
        Prepared for optional twin tank system for longer flying time
        Additional header tank for bubble-free fuel supply of turbine (included)

    Rotor Head:

        Full ball bearings
        Heavy duty linkages
        9mm head axle made from special high quality steel
        CNC machined aluminum swashplate
        CNC machined main rotor grips
        CNC machined main rotor head
        High quality swashplate heim ball/ball bearing
        High precise swash plate follower arms with 4 ball bearings each


    Tail Rotor:

        Full ball/thrust bearings
        Tail Rotor hub made from special high quality steel
        Graphite tail fin
        CNC aluminum “open” gearbox
        CNC machined tail gears made from aluminum with hard anodizing surface and POM
        Aluminum 22mm tail boom
        Positive control system
        Hardened tail rotor output shaft
        High precise tail slider
        Carbon/Aluminum boom supports

    Turbine engine:

    Whiplash Special Edition two shaft kero-start turbine for R/C helicopters made by Turbine Solutions.

        Two shaft kero-start engine
        Gearbox output shaft rpm range: 4,000 to 15,000 rpm
        Max Power Output: 6.8 HP / 5Kw @ 190,000 rpm
        Max Torgue: 4Nm / 2.9 ft Lbs @ 13,500 rpm
        Fuel consumption: 176ml/Min / 5.8oz/Min

    Canopy:

        High Visibility Painted Epoxy-Glass Canopy

    SKU: MA1035-2
    €1650.00
    inc. VAT

     72HR STOCK
  • Miniature aircraft Furion 6 FBL - Kit version

    Miniature aircraft Furion 6 FBL - Kit version

    Miniature aircraft Furion 6 FBL - Kit version
     
       Aluminum Boom Clamps
        Motor Shaft Lower Bearing Support
        Optional Pinion Gear Available
        Removable Battery Tray

    Flybarless Rotor Head:

        Full Ball Bearings/Thrust Bearings
        Heavy Duty Hiller Rods
        8mm Head Axle
        CNC Machined Aluminum Swashplate
        Hex/Hardened Control Balls
        CNC Aluminum Head Button
        CNC Aluminum Blade Grips
        High Quality Swashplate Heim Ball/Ball Bearing
        Simple SleekDesign

    Tail Rotor:

        Full Ball Bearings
        Graphite Painted Tail Fin
        Secure CNC Aluminum Tail Rotor Clamps
        22mm Lightweight Aluminum Tail Boom
        Positive Control System
        2mm Control Rod
        Hardened Tail Rotor Output Shaft
        Carbon/Aluminum Boom Supports

     Canopy

        High Visibility Painted Epoxy-Glass Canopy by Canomod

     Additional Furion 6 Specifications:
     
    6S Battery Setup

        Recommended Motor KV Range: 850-900
        Gear Ratio: 8.38:1 (12t pinion gear/103t main gear)
        Battery Size: 6S 5000mah
        Main Rotor RPM: 2100-2300
        Motor Shaft Size: 6mm x 30/32mm

    10S Battery Setup

        Recommended Motor KV Range: 540-560
        Gear Ratio: 9.08:1 (11t pinion gear/103t main gear)
        Battery Size: 2 x 5S 4000-5000mah
        Main Rotor RPM: 2200-2600
        Motor Shaft Size: 6mm x 30/32mm

    SKU: MA1029-1
    €660.00
    inc. VAT

     72HR STOCK
  • Miniature aircraft Whiplash 730E (FBL) - Kit

    Miniature aircraft Whiplash 730E (FBL) - Kit

    • NEW aggressively-styled, stiffer frames with side-by-side battery mounting for better GC control
    • Increased cyclic and tail rate capabilities for more locked-in, slop free controls, and easier battery change-outs.
    • 20° helical drivetrain with hardened steel pinion gear and CNC machined main gear.
    • Improved gear ratios of 9:1 and 9.75:1 to match today’s motor Kv market.
    • Adjustable motor mount for fine tuning gear mesh.
    • Steel-sleeved main gear hub eliminates middle bearing block wear.
    • True 6061-T6 CNC machined aluminum components
    • CNC machined aluminum triple main shaft bearing blocks
    • Narrowed tuff strut landing gear
    • Ball bearing supported pinion gear
    • Improved electronics placement and wiring options

    Rotor Head:

        Direct controlled 120 (degree) CCPM
        Heavy duty linkages
        9mm head axle
        CNC machined aluminum swashplate
        CNC machined main rotor grips
        CNC machined main rotor head
        High quality swashplate heim ball/ball bearing

    Tail Rotor:

        Full ball/thrust bearings
        Graphite tail fin
        CNC aluminum “open” gearbox
        Carbon 22mm tail boom
        Hardened tail rotor output shaft
        Carbon/Aluminum boom supports and CNC machined aluminum boom clamps

    Model Specifications:

        Length: 52.5" (1333mm)
        Height: Flybar - 6.5” (419mm)
        Rotor Span: 1561-1601mm - 690-730mm blades
        Tail Rotor Span: 286mm with 105mm T/R blades
        Avg. Ready-to-Fly Weight: 11.5-12.5lbs - 5.22-5.67kg (w/batteries)
        Main Rotor Blades: 690-730mm
        Power: 12S, 490-560KV

    SKU: MA1034-1
    €899.00
    inc. VAT

     72HR STOCK
  • Miniature aircraft Whiplash-G Gasser version II Flybarless Helicopter Kit

    Miniature aircraft Whiplash-G Gasser version II Flybarless Helicopter Kit

    Chassis:

    •     Sturdy graphite main frame unit.
    •     All C/F parts are made from 100% carbon.
    •     CNC machined Delrin 117 tooth helical main gear
    •     High quality one way bearing Made in Germany
    •     High quality one way bearing hub, full ball bearings
    •     Heavy duty, high quality front tail drive gears Made in Germany
    •     High precise two-piece clutch bell with double ball bearing support
    •     Optional gear ratios
    •     True T6-6061 CNC machined aluminum components
    •     CNC machined aluminum triple main shaft bearing blocks
    •     Direct controlled 120 (degree) CCPM
    •     CNC machined aluminum boom clamps
    •     CNC machined aluminum engine mount
    •     Full ball bearings throughout
    •     High quality landing gear struts

    Rotor Head:

    •     Full ball bearings
    •     Heavy duty linkages
    •     9mm head axle made from special high quality steel
    •     CNC machined aluminum swashplate
    •     CNC machined main rotor grips
    •     CNC machined main rotor head
    •     High quality swashplate heim ball/ball bearing
    •     High precise swash plate follower arms with 4 ball bearings each

    Tail Rotor:

    •     Full ball/thrust bearings
    •     Tail Rotor hub made from special high quality steel
    •     Graphite tail fin
    •     CNC aluminum “open” gearbox
    •     CNC machined tail gears made from aluminum and POM
    •     Aluminum 22mm tail boom
    •     Precise running torque tube w. 3 ball bearings
    •     Hardened tail rotor output shaft
    •     High precise tail slider
    •     Carbon/Aluminum boom supports
    •     Carbon Tail Control Rod

    Air Filter:

        High Flow Air Cleaner X-cell

    Canopy:

    High Visibility Painted Epoxy-Glass Canopy

    Specifications:

    •     Heli Length     52.5" (1343mm)
    •     Heli Height     17.25" (439mm)
    •     Rotor Span     1561-1621mm - 690-720mm blades
    •     Tail Rotor Span     286mm with 105mm T/R blades
    •     Avg. Ready-to-Fly Weight     12-13lbs - 5.6-6.2kg (less fuel)
    •     Main Drive Ratio   6.89:1 (7.3:1, 7.8:1 options)
    •     Tail Drive Ratio   4.67:1
    •     Main Rotor Blades    690-720mm
    •     Recommended Power   23-32cc R/C Style Gas Engine
    SKU: MA1033-3
    €1199.00
    inc. VAT

     LOW STOCK
  • Miniature aircraft Whiplash-N II Nitro V2 Flybarless helicopter Kit

    Miniature aircraft Whiplash-N II Nitro V2 Flybarless helicopter Kit

    Miniature aircraft Whiplash-N II Nitro V2 - Kit version, no blades or electronics/motors included
     
    Chassis:

    •     Sturdy graphite main frame unit.
    •     All C/F parts are made from 100% carbon.
    •     CNC machined Delrin 117 tooth helical main gear
    •     High quality one way bearing Made in Germany
    •     High quality one way bearing hub, full ball bearings
    •     Heavy duty, high quality front tail drive gears Made in Germany
    •     High precise two-piece clutch bell with double ball bearing support
    •     Optional gear ratios
    •     True T6-6061 CNC machined aluminum components
    •     CNC machined aluminum triple main shaft bearing blocks
    •     Direct controlled 120 (degree) CCPM
    •     CNC machined aluminum boom clamps
    •     CNC machined aluminum engine mount
    •     Full ball bearings throughout
    •     High quality landing gear struts

    Rotor Head:

    •     Full ball bearings
    •     Heavy duty linkages
    •     9mm head axle made from special high quality steel
    •     CNC machined aluminum swashplate
    •     CNC machined main rotor grips
    •     CNC machined main rotor head
    •     High quality swashplate heim ball/ball bearing by original SKF
    •     High precise swash plate follower arms with 4 ball bearings each

    Tail Rotor:

    •     Full ball/thrust bearings
    •     Tail Rotor hub made from special high quality steel
    •     Graphite tail fin
    •     CNC aluminum “open” gearbox
    •     CNC machined tail gears made from aluminum and POM
    •     Aluminum 22mm tail boom
    •     Positive control system
    •     Hardened tail rotor output shaft
    •     High precise tail slider
    •     Carbon/Aluminum boom supports

    Canopy:

    •     High Visibility Painted Epoxy-Glass Canopy

    Specifications

    • Heli Length :    52.5" (1333mm)
    • Heli Height :   17.5" (445mm), Flybarless - 17" (432mm)
    • Rotor Span : 1561-1601mm - 690-710mm blades
    • Tail Rotor Span: 286mm with 105mm T/R blades
    • Avg. Ready-to-Fly Weight: 10-11lbs - 4.5-5kg (less fuel)
    • Main Drive Ratio : 8.35 : 1 7.8 : 1 (optional) 7.3 : 1 (optional)
    • Tail Drive Ratio : 4.66:1
    • Main Rotor Blades : 690-710mm
    • Recommended Power : .90 to 120 size glow
    SKU: MA1031-3
    €990.00
    inc. VAT

     72HR STOCK

Manufacturers

Back