Speed Fuselage – Red & White designed by Align and suitable for T-REX 450L
Utilizing wrap-around aerodynamic design, the brand new 450L Speed Fuselage has an attention grabbing unique curve. Its tail section is wrapped with painted carbon fiber shell, resulting in superior visibility in mid-air, and further enhance the beauty of highly difficult maneuvers. The low aerodynamic drag enables high speed flights to be easily achievable. In addition, the ergonomic design simplifies installation; just a few simple steps with few screws to complete the install, easily outfitting your helicopter with a beautiful body.
Speed Fuselage – Red & Yellow designed by Align and suitable for T-REX 450L
Utilizing wrap-around aerodynamic design, the brand new 450L Speed Fuselage has an attention grabbing unique curve. Its tail section is wrapped with painted carbon fiber shell, resulting in superior visibility in mid-air, and further enhance the beauty of highly difficult maneuvers. The low aerodynamic drag enables high speed flights to be easily achievable. In addition, the ergonomic design simplifies installation; just a few simple steps with few screws to complete the install, easily outfitting your helicopter with a beautiful body.
Speed Fuselage – White & Blue designed by Align and suitable for T-REX 450L
Utilizing wrap-around aerodynamic design, the brand new 450L Speed Fuselage has an attention grabbing unique curve. Its tail section is wrapped with painted carbon fiber shell, resulting in superior visibility in mid-air, and further enhance the beauty of highly difficult maneuvers. The low aerodynamic drag enables high speed flights to be easily achievable. In addition, the ergonomic design simplifies installation; just a few simple steps with few screws to complete the install, easily outfitting your helicopter with a beautiful body.
Speed Fuselage – Yellow & Blue designed by Align and suitable for T-REX 450L
Utilizing wrap-around aerodynamic design, the brand new 450L Speed Fuselage has an attention grabbing unique curve. Its tail section is wrapped with painted carbon fiber shell, resulting in superior visibility in mid-air, and further enhance the beauty of highly difficult maneuvers. The low aerodynamic drag enables high speed flights to be easily achievable. In addition, the ergonomic design simplifies installation; just a few simple steps with few screws to complete the install, easily outfitting your helicopter with a beautiful body.
Blade 180 CFX Goblin Fuselage FULL CARBON Canopy Ziczac
Canomod is pleased to deliver our all new Xtreme Light Carbon (XLC) products.
This all new canopy construction method combines high quality carbon fiber and epoxy resin, making these canopies extremely light and durable.
Canomod is also offering a customization service for these superb new canopies. You now have the flexibility to change the color pallet and pattern, as well as adding your name and custom logos to the canopy.
If you do not require any customization, you can purchase right away, and we will ship immediately if the canopy is in stock.
Specifications:
High-end airbrushed carbon fiber canopy
Automotive-quality paint and clear coat
High quality airbrushed details
Remove the horizontal and vertical fins, the tail gear box, metal stabilizer mount, boom supports, and tail pushrod guides.
Carefully install the Fusuno fiberglass tail boom by sliding it forward over the boom. Be sure the Align aluminum tail boom goes through the holes of the foam supports inside the fiberglass tail boom.
Secure the fiberglass tail boom by installing the four button head cap screws M2.5 x 6.
Reinstall the tail gear box and secure the Fusuno CF vertical fin.
Remove the stock tail pushrod and install the Fusuno CF tail rod.
Please adjust the tail pushrod linkage length and re-setup your tail servo endpoints as necessary.
Separated body, it’s very easy to replace battery!
Weight approximate: 25g (Canopy + Boom).
INSTALLATION GUIDE
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
Separated body, it’s very easy to replace battery!
Weight approximate: 25g (Canopy + Boom).
INSTALLATION GUIDE
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
Separated body, it’s very easy to replace battery!
Weight approximate: 25g (Canopy + Boom).
INSTALLATION GUIDE
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
Remove the horizontal and vertical fins, the tail gear box, metal stabilizer mount, boom supports, and tail pushrod guides.
Carefully install the Fusuno fiberglass tail boom by sliding it forward over the boom. Be sure the Align aluminum tail boom goes through the holes of the foam supports inside the fiberglass tail boom.
Secure the fiberglass tail boom by installing the four button head cap screws M2.5 x 6.
Reinstall the tail gear box and secure the Fusuno CF vertical fin.
Remove the stock tail pushrod and install the Fusuno CF tail rod.
Please adjust the tail pushrod linkage length and re-setup your tail servo endpoints as necessary.
Separated body, it’s very easy to replace battery!
Weight approximate: 25g (Canopy + Boom).
INSTALLATION GUIDE
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
Separated body, it’s very easy to replace battery!
Weight approximate: 25g (Canopy + Boom).
INSTALLATION GUIDE
Remove the tail gear box, tail boom clamp, and tail pushrodguide set.
Remove the plastic ball link from the tail pushrod. Put this aside for re-installation later. We suggest you count the number of turns to remove, so it can be later re-installed in the same position.
Install the Fusuno tail boom by sliding it forward over the stock boom. Be sure the metal tail rod goes through the two carbon tail pushrod guides on the Fusuno tail boom.
Remove two button head screws on both sides of the frame.
Push the frame out to create a slot between the frame and the front boom mount so you are able to slide the tail boom inside the slot.
Secure the Fusuno tail boom by tighten up the two button head screws.
Re-install the plastic ball linkon to the tail pushrod. Return the rod to its original length by twisting the ball link in and counting the same number of turns as when you removed it. Recheck your tail servo endpoints as necessary.
Re-install the tail gear box and secure using the Fusuno CF vertical fin.
LOGO 550 Fusion is a fuselage kit for the LOGO 550 SX.
It's sleek and streamlined design with the fluent passage between canopy and tail boom cover improve the speed flying capabilities of the 550.
The improved visibility makes dynamic and big air flying even more fun.
3D-flight is of course also possible with the LOGO Fusion.
The light takeoff-weight beginning at approx. 7.5 pounds (equipped with 6s 5.000 mAh batteries) makes the machine very nimble.
The tail boom cover slides onto the LOGO 550 SX mechanics and is bolted to the prepared mounting points on the V2 chassis. At the tail, it is held by additional clamps.
All r/c components keep their place on the mechanics, they are well accessible when you remove the large canopy.
The Fusion Fuselage Kit comes ready to mount, including a new tail fin and all the required small parts for the assembly, for the LOGO 550 SX mechanics.
Please take note: this Fuselage Kit only fits the LOGO 550 SX.
It will take considerable efforts to update other models of the LOGO 500 line.
If in doubt, please consult the manual of your LOGO helicopter and the current manual of the LOGO 550 SX, to see what is different.
LOGO 690 Fusion is a fuselage kit for the LOGO 690 SX.
It's sleek and streamlined design with the fluent passage between canopy and tail boom cover improve the speed flying capabilities of the 690.
The improved visibility makes dynamic and big air flying even more fun.
3D-flight is of course also possible with the LOGO Fusion. The light takeoff-weight beginning at approx. 10.8 pounds (equipped with 12s 5.000 mAh batteries) makes the machine very nimble.
The tail boom cover slides onto the LOGO 690 SX mechanics and is bolted to the prepared mounting points on the V2 chassis. At the tail, it is held by additional clamps.
All r/c components keep their place on the mechanics, they are well accessible when you remove the large canopy. The Fusion Fuselage Kit comes ready to mount, including a new chassis box in black and all the required small parts for the assembly, for the LOGO 690 SX mechanics.
Please take note: this Fuselage Kit only fits the LOGO 690 SX.
It will take considerable efforts to update other models of the LOGO 600 line.
If in doubt, please consult the manual of your LOGO helicopter and the current manual of the LOGO 690 SX, to see what is different.
The Uvular is a fuselage for LOGO 600 SE. Its aerodynamic design makes for great speed flying performance. Pilots who enjoy covering greater space in the air by a dynamic flying style will also welcome that the clear contours of the Uvular make for great visibility. As the Uvular encloses the chassis like a shell, any gear noises are covered up, so that almost only the sound of the blades can be heard. The Uvular will do 3D just as well, as it weighs under 4.5 kg.
The LOGO 600 SE mechanic is inserted completely into the Uvular, including the tail boom. All RC components can stay in their place and are easily accessible by removing the front cover. The Uvular is shipped painted and ready for inserting the LOGO 600 SE mechanic.
To turn a LOGO 600 into LOGO 600 SE for using it in the Uvular an Mikado upgrade MIK-4326 is required.
