Flight Controllers & Parts

Flight Controllers & Parts Here you can find assortment of Flight and Speed controllers, especially designed for Multi-rotors. Flashable and programmable Speed controllers .

Products


  • RF Shielding Copper sheet Signal Blocking Material-Controller/esc protection

    RF Shielding Copper sheet Signal Blocking Material-Controller/esc protection

    • High Performance Copper Shielding sheet 
    • 20x30cm
    • >60db attenuation in 10MHz-3GHz
    • Excellent Radiation protection
    • EMF Wave Blocking (Best Value for Blocking Ability)

     

    SKU: EMICO
    €16.00
    inc. VAT

     IN STOCK
    NEW
  • RJX Brushed F3 EVO Flight Control Board

    RJX Brushed F3 EVO Flight Control Board

    RJX Brushed F3 EVO Flight Control Board Support PPM SBUS receiver Hexacopter LED function 1s 2s battery for Tiny Whoop Mini Micro Nano quad FPV Racing.

    This 32 bit brushed flight control is based on SP RACING F3 EVO firmware.
    Specailly designed circuit ensure 5V output for UART1/2/3 despite 1S or 2S input,receiver output at 3.3V.
    Features STM32F303CCT6 + MPU6500, advanced hardware guarantee more stable flight.
    Support battery voltage monitor, buzzer and led function.
    Support basically all coreless motors available, including 1020 motor.
    Large current NMOS transistors enable the board to sustain up to 10A operating current per channel. Each channel is equipped with a freewheeling diode.
    Go to UART3 in cleanflight to configurate.
    PPM and SBUS receiver soldered to the UART2, Go to UART2 for SBUS configuration.
    Dimensions:22MM * 32.5MM, thickness: 1.2MM.
    Note: The propeller must be removed during configuration F3 EVO 1.13.0 firmware by default, if you need to reflash, please input "set motor_pwm_rate = 1000" in the Cleanflight configuration software and save!

    Specification:

    • Micro size 22mm*32.5mm,weight 3g.In support of the world almost all hollow cup motor,including 1020 coreless motor.
    • Based on F3 flight controller , Specially designed and built for quads around 100mm and sub 100mm class. Support Quadcopter and Hexacopter, LED function.
    • Features STM32F303CCT6 + MPU6500, advanced hardware guarantee more stable flight.
    • Support for PPM, SBUS, DSM receiver, Support battery voltage monitor and buzzer function.
    • Support 1S (3.7--4.2V) and 2S (7.4--8.4V) lipo battery,with 2s, you could get even more fierce racing experience than 1s. Note: the minimum voltage power that supports the borad to work normally is more than 4.8V.

    Note: 1s battery can only offer 3.7V power, the minimum voltage power that supports the borad to work normally is more than 4.2V.

     

    SKU: RJX1309
    €22.90
    inc. VAT

  • Seriously Dodo Flight Controller board

    Seriously Dodo Flight Controller board

    DO DO Flight controller Board: Seriously, do you want more from your flight controller? The DoDO is your answer!

    Features:

    •     8 input channels
    •     8 output channels
    •     3 UARTs (GPS, Telemetry, S.bus)
    •     2-6s input power
    •     5v output - 0.5A Max (No more external regulators to get in your way!)
    •     stm32 f303 **NEW STM32F3 CPU WILL SUPPORT LOWER LOOPTIMES**
    •     16mbit dataflash  **2 MEGABYTES OF STORAGE FOR DATA LOGGING**
    •     Barometer
    •     Spektrum satellite port (Connector not included)
    •     MPU6050 accelerometer/gyro
    •     36x36mm board with 30.5mm mounting holes (Same as CC3D, Naze32)
    •     5.4g
    •     MicroUSB socket
    •     Dedicated connector for WS2811-style LEDs
    •     Operates on Cleanflight
    •     Will accept S.BUS connection directly with no inversion or hacks.

     

    SKU: DODOFC
    €55.00
    inc. VAT

  • Sky-Hero Anakin Club Racer OP REVOLUTION

    Sky-Hero Anakin Club Racer OP REVOLUTION

    Sky-Hero Anakin Club Racer OP REVOLUTION

    SKU: SKH04-020
    €59.90
    inc. VAT

     IN STOCK
  • SP Racing F3 Flight Controller Acro version for racing/acro flying 6 DOF

    SP Racing F3 Flight Controller Acro version for racing/acro flying 6 DOF

    The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you're into FPV racing, acrobatic flying or aerial photography it's perfect. Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.

    Acro Version have 6 DOF while Deluxe version has 10 DOF, including Barometer and Compass: Additional sensors for altitude and direction

    The SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.

    Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers and community. No more out-of-date wiki pages and second-hand information.

    Features

    •     Practical - Easy to access connectors and solder pads.
    •     Configurable - Choose to use connectors, solder pads or pins.
    •     Stackable - Mount to your PDB or OSD.
    •     Compact - Only 36x36mm.
    •     Professional - Symmetrical, Neat and Tidy.
    •     8 Dedicated PWM outputs
    •     8 PWM Inputs
    •     36 I/O Connections
    •     72Mhz Clock Speed
    •     3 Hardware Serial Ports
    •     64Mb Flash Storage

    Specifications (Acro Version)

    The hardware was designed by the lead developer of Cleanflight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the Cleanflight users, contributors and top-pilots.

        36x36mm board with 30.5mm mounting holes
        Weight ~6 grams
        Acro version is without Compass and Barometer Sensors
        STM32F303 CPU, 72Mhz inc FPU
        High-Capacity Flash (Acro and Deluxe)
        MPU6050 accelerometer/gyro
        MicroUSB socket
        2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
        8x 3pin though-holes for pin headers for ESC/Servo connections
        2x 4pin though-holes for pin headers for 2x serial ports
        1x 2pin though-holes for pin headers for battery voltage
        1x 2pin though-holes for pin headers for buzzer
        1x 4pin JST-SH socket for I2C
        1x 4pin JST-SH socket for SWD debugging

    Flight Performance

        The SPRacingF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails.

    No-Compromise I/O

        Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!

    Configurable

        The SPRacingF3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).

    Tiny and lightweight

        The SPRacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

    Flight Logging

        On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

    Next-Generation CPU

        The SPRacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time.
        Loop times up to ~2x as fast as previous-generation STM32F1 based boards.

    Developer Friendly

        Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

    OneShot ESC

        Full support for OneShot ESCs for easy PID tuning and a sharper response.

    Broad RC receiver Support

        Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).

    Programmable LED

        Dedicated output for programmable LEDs - great for orientation, racing and night flying.

    Battery Monitoring

        Battery monitoring ports for voltage and current.

    Sonar

        Sonar support for precision low-altitude hold.

    I2C Port

        I2C port always powered, perfect for external sensors or always-on OLED Screen.

    Buzzer

        Buzzer port for audible warnings and notifications.

     

    SKU: SPRF3ACR
    €44.00
    inc. VAT

     IN STOCK
  • SP Racing F3 Flight Controller Deluxe version 10 DOF for Multicopter, Compass, Barometer

    SP Racing F3 Flight Controller Deluxe version 10 DOF for Multicopter, Compass, Barometer

    SPRacing F3 Flight Controller Deluxe Version runs Cleanflight and suits the Drone Racers who need all the features that have been specially designed for racing.

    SP Racing F3 Flight Controller (SPRacingF3) has been designed to deliver incredible flight performance based on proven and tested sensors while additionally providing unparalleled and I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU.

    Acro Version have 6 DOF while Deluxe version has 10 DOF, including Barometer and Compass: Additional sensors for altitude and direction

    The SP3 Controller is favoured amongst some of the top pilots for its performance , reliability and black box recordings .

    Flight Performance - The SPRacingF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails.

    Flight Logging - On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

    Developer Friendly - Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

    No-Compromise I/O - Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!

    Tiny and Lightweight - The SPRacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

    Next Gen CPU - Full support for OneShot ESCs for easy PID tuning and a sharper response.

    Broad RC Receiver Support - Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).

    Battery Monitoring - Ports to enable monitoring of voltage and current.

    12C Port - I2C port always powered, perfect for external sensors or always-on OLED Screen.

    Programmable LED - Dedicated output for programmable LEDs - great for orientation, racing and night flying.

    Buzzer - Buzzer port for audible warnings and notifications.

    Specifications of the Flight Controller.

    •     36x36mm board with 30.5mm mounting holes
    •     Weight ~6 grams
    •     STM32F303 CPU, 72Mhz inc FPU
    •     High-Capacity Flash (Acro and Deluxe)
    •     MPU6050 accelerometer/gyro
    •     MS5611 barometer (Deluxe only)
    •     HMC5883 compass (Deluxe only)
    •     MicroUSB socket
    •     2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
    •     8x 3pin though-holes for pin headers for ESC/Servo connections
    •     2x 4pin though-holes for pin headers for 2x serial ports
    •     1x 2pin though-holes for pin headers for battery voltage
    •     1x 2pin though-holes for pin headers for buzzer
    •     1x 4pin JST-SH socket for I2C
    •     1x 4pin JST-SH socket for SWD debugging

    Package including Case, Pins, Cables for connections

    SKU: SPRF3DL
    €49.90
    inc. VAT

     IN STOCK
  • SP Racing F3 Flight Controller Integrate OSD with Protective Case for FPV Multicopter

    SP Racing F3 Flight Controller Integrate OSD with Protective Case for FPV Multicopter

    The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you're into FPV racing, acrobatic flying or aerial photography it's perfect. Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.

    This version is Acro Version, the pinS ARE NOT soldered

    Specification:     

    - 36x36mm board with 30.5mm mounting holes
    - STM32F303 CPU, 72Mhz inc FPU
    - High-Capacity Flash (Acro and Deluxe)
    - MPU6050 accelerometer/gyro

    - 2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
    - 1x 4pin JST-SH socket for SWD debugging
    - 1x 5pin JST-SH socket for Flash firmware and Configuration (Connect to the CP2104 uart to usb tool)
    - 8x 3pin though-holes for pin headers for ESC/Servo connections
    - 4x 2pin though-holes for pin headers for 1x serial port and i2c port
    - 8x 1pin though-holes for pin headers for battery voltage/buzzer/Video in/Video out

    Package included:
    - 1 x SP Racing Acro Version flight controller integrate OSD
    - 1 x Protective case
    - 1 x Programmer
    - 4 x Connection cable
    - Pins

    SKU: SPRF3OSD
    €42.00
    inc. VAT

     IN STOCK
  • Spedix CC3D Flight Controller

    Spedix CC3D Flight Controller

    Features:

    • One of the most popular open source multirotor flight controller developed by Open Pilot team
    • Redesigned and manufactured by Spedix to improve connectivity. No adapter is required to setup DSM2/DSMX satellites and S.Bus receivers
    • Optimized ESC pins directions to make wiring in a neat way. No ESC wires come from the two sides of a multirotor frame
    • Assembled in the factory with protection case

    Specifications:

    • Input Voltage: 4.8-6.0V
    • Dimensions:39x39x12mm
    • Weight: 14g
    • Firmware Version:15.02

    Contents:

    • CC3D controller with case (1x)
    • Cable set (1x)
    SKU: SPX71004
    €19.90
    inc. VAT

     LOW STOCK
  • Spektrum F400 Raceflight Flight Controller

    Spektrum F400 Raceflight Flight Controller

    Spektrum F400 Raceflight Flight Controller

    Spektrum has combined a state of the art F4 processor with proprietary Raceflight One firmware to bring you the cutting edge in FPV racing performance.
    Featuring an integrated 5v regulator, pilots will no longer worry about providing regulated power to your flight controller.
    The Spektrum F400 flight controller makes wiring the receiver simple by only needing one connection for power, signal, and telemetry information.
    Pair it with a SPM4649T Serial Telemetry receiver and the pilot can feed all available telemetry data to their Spektrum radio transmitter.
    The processor in the Spektrum F400 is capable of a lighting fast 180MHz update speed; giving the pilot uncompromised speed, precision, and power. Connect the F400 Raceflight Flight Controller with a 32KHz capable ESC for optimal performance.

    Key Features:

    • Compatible with all Spektrum receivers and other brands. No Built in SBUS Inverter
    • Ready for the new SPM4649T Telemetry Quad Racing Receiver for Full Telemetry Output Support
    • Standard form factor 36mm x 36mm mounting holes: 30.5mm squared to center hole
    • RaceFlight One dedicated support and development
    • High Speed 32khz gyro
    • Leading Edge F4 Processor
    • LED Driver for WS2812b programmable LED
    • ESC flashing and configuration built into configurator
    • Built in 5V Regulator, 2 - 6S battery input
    • Dedicated port for Spektrum Telemetry laptimer
    • 16mb Flash Memory for Black Box

    Specification:

    • Height: 0.2 inch (6mm)
    • Length: 1.4 inch (36mm)
    • Weight: 0.3 ounce (8 grams)
    • Width:     1.4 inch (36mm)

     

    SKU: SPMFCF400
    €62.90
    inc. VAT

     LOW STOCK
  • The Cube Kore (Without Cube)

    The Cube Kore (Without Cube)

    FEATURES AT-A-GLANCE

        Up to 12-cell Lithium battery (50.4V)
        140A continuous current with 280A surges
        Power and signal for ESCs conveniently located in corners
        12V navigation light power available at each cornerBuilt-in power distribution
        Built-in voltage and current sense
        Redundant power supplies for flight critical components
        Payload connectors with resettable fuses for 5V, 12V, and direct battery power
        Good power and error indicator lights
        Built-in buzzer with volume control
        Connectors for every function of Pixhawk Cube
        Easily accessible PWM voltage level selector (3.3V or 5V)
        Resistant to ground bounce on PWM signal
        Connector-compatible with standard ProfiCNC carrier board
        Connector ports for debugging IO and FMU processors

    STANDARD CABLES:

    4-pin JST GH
    6-pin JST GH
    PAYLOAD POWER CABLES:

    4-pin Clik-Mate 1.25mm (for 5V payload power)
    5-pin Clik-Mate 1.25mm (for 12V payload power)
    6-pin Clik-Mate 1.25mm (for battery payload power)

    NOTE: Pixhawk 2.1 Cube NOT included.

    SKU: HX4-06038
    €220.00
    inc. VAT

     LOW STOCK
    NEW
  • Ublox M8N GPS Module with compass,Case for Pixhawk

    Ublox M8N GPS Module with compass,Case for Pixhawk

    Ublox M8N GPS Module with compass,Case for Pixhawk

    Package Including:

    • Supports GPS/ Galileo / BDS/ GLONASS/ QZSS/ SBAS
    • M8N chip Included
    • With optimized module and internal compass.
    • The refresh speed is raised to 10HZ.
    SKU: M8NGPS
    €79.00
    inc. VAT

     IN STOCK
  • USB ISP USBasp Programmer for ATMEL AVR

    USB ISP USBasp Programmer for ATMEL AVR

    USB ISP USBasp Programmer for ATMEL AVR with Case, good tool to have to flash ESC.

    SKU: AVRATMEL
    €10.00
    inc. VAT

     LOW STOCK
  • Vector FPV Controller with LEADS

    Vector FPV Controller with LEADS

    Eagle Tree Vector FPV Controller with leads Current Sensor

    Key Features:

    • The Kit includes Base Controller Unit, GPS/Magnetometer and Current Sensor/ PSU
    • Built-in OSD with COLOR GRAPHICS - and fully customizable screens
    • Fixed wing and Multirotor Flight Controller - with GPS modes and RTH
    • Simple to set up and Operate Out of the Box -with no PC required for most features
    • Compatible with PCM, SPPM and S.BUS RxER Support - with four types of RSSI
    • Expandable with Additional Sensors, Accessories - internet firmware updates
    • Fly with or without your FPV camera and transmitter
    • Reduced wiring,  innovative wiring harness with power distribution simplifies connections
    • Current Sensor with efficient filtered 12v and 5v PSU
    • Built-in Altimeter, IMU and Magnetic Compass Sensors


    Just some of the features this amazing system will support :

    • Full Color, Fully Customizable OSD Screens
    • Voice alerts: the Vector can speak flight information to you
    • Variometers - OSD charting variometer or acoustical tone.
    • RSSI : Four version supported - Analogue, PCM, Spektrum, Virtual SPPMRSSI
    • All features of original OSD Pro module
    • 2D / 3D Flight Stabilization Modes
    • RTH - Return To Home
    • Geofence: lets you program a maximum ceiling and distance for your model.
    • Loiter: Holds the present position (multirotor) or circles (fixed wing)
    • Data Logging and Telemetry - of sensor and GPS information via internal storage. 
    SKU: VEC-PKG-LEADS
    €279.90
    inc. VAT

     72HR STOCK

Manufacturers

Back