Flight Controllers & Parts

Flight Controllers & Parts Here you can find assortment of Flight and Speed controllers, especially designed for Multi-rotors. Flashable and programmable Speed controllers .

Products


  • KK-Mini 2.1.5 Multi-Rotor Flight Control Board with LCD screen

    KK-Mini 2.1.5 Multi-Rotor Flight Control Board with LCD screen

    The next evolution of the rotor revolution is here!! The KK-mini is packing all the same power, but with a new mighty-mini form factor.

    The KK-Mini is the next Big/Small evolution of the first generation KK flight control boards. The KK-Mini is based on the KK2.1.5 architecture and has all the same inputs and outputs as well as the full functionality of its big brother. The new 36mm designed was adapted to fit the needs of the new mini market, but don’t let its size fool you as it's just as much at home in any size multi-rotor. The KK mini still utilizes a built in GUI using a hi-res mini LCD and 4 micro buttons for the same great KK experience. It was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts.

    A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts!

    The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system, making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK-Mini is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for on-board soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board.

    The KK-Mini added polarity protection to the voltage sense header and on-board buzzer. The voltage sense line has been updated for better accuracy.

    If you’re new to multi-rotor flight or have been unsure about how to setup a KK board, then the KK-Mini was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy.

    Specs:

    • Size: 36x36x11.5mm (mounting holes 30.5x30.5mm)
    • Weight: 8.6g
    • IC: Atmega644 PA
    • Gyro/Acc: 6050MPU InvenSense Inc.
    • Auto-level: Yes
    • Input Voltage: 4.8-6.0V
    • AVR interface: standard 6 pin.
    • Signal from Receiver: 1520us (5 channels)
    • Signal to ESC: 1520us
    • LCD size: 24*18mm
    • Mini buttons size:Four 3.3*4.2mm
    • Voltage sensor: One red positive pin header for.
    • Input rail: Single row 2.54mm pitch pin header for input signal
    SKU: KK215MINI
    €26.90
    inc. VAT

     IN STOCK
  • KK2.1.5 Multi-rotor Flight Control Board With LCD, 6050MPU, Atmel 644PA

    KK2.1.5 Multi-rotor Flight Control Board With LCD, 6050MPU, Atmel 644PA

    The latest revision of this popular flight controller has arrived! Version 2.1.5 has updated sensors, more memory and safety enhancements including polarity protection and better pin labelling.

    The KK 2.1.5 board brings easy multi-rotor flight to beginners and experts alike. The LCD screen and user-friendly software can be fully configured on the board itself instead of having to use a PC based configuration tool. Just select your multi-rotor type and motor layout, calibrate the ESCs and radio and off you go. Just follow the prompts on the LCD screen.

    The board now uses the 6050MPU inertial measurement unit, containing a high precision gyro and accelerometer, so the KK 2.1.5 board now comes with an auto-level function. The Atmel Mega644PA 8-bit AVR RISC-based microcontroller has 64k of memory. The voltage detection header now also features polarity detection. Also included in the package is a piezo buzzer to provide audio feedback and warnings when arming or disarming the board.

    Specifications:

    • Size: 50.5mm x 50.5mm x 12mm
    • Weight: 21 gram (Include Piezo buzzer)
    • IC: Atmega644 PA
    • Gyro/Acc: 6050MPU InvenSense Inc.
    • Auto-level: Yes
    • Input Voltage: 4.8-6.0V
    • AVR interface: standard 6 pin.
    • Signal from Receiver: 1520us (5 channels)
    • Signal to ESC: 1520us

    Features:

    1. Based on the original design, but improved with the convenience to connect to a satellite or S.Bus receiver directly, bypassing the requirement of adapter as normal KK board.
    2. Engineered from the ground up to bring multi-rotor flight to everyone, not just the experts.
    3. The LCD screen and built in software makes install and setup easier than ever.
    4. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go!

    What is a Multi-Rotor Control board you ask?
    The KK2 Multi-Rotor controller is a flight control board for multi-rotor aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the 6050MPU gyro/acc (roll, pitch and yaw) then passes the signal to the Atmega644PA IC. The Atmega644PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.
    The KK2 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega644PA IC via the aileron, elevator, throttle and rudder inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

    SKU: KK2.1.5
    €27.90
    inc. VAT

  • Multiwii FC I2C-GPS NAV Module

    Multiwii FC I2C-GPS NAV Module

    NAV Module x 1

    UART 4Pin cable (to GPS) 200mm x1

    I2C 4Pin cable (to FC) 100mm x1

    Features:

    All GPS data available via the I2C bus to connect to 328P Multiwii FC

    A LED on board show GPS 3D Fix status

    ATMega 328P Microcontroller

    2 Molex 1.25mm 4Pin socket for GPS receiver and FC

    2 port for ISP and FTDI

    Specification:

    Dimension: 20mmX30mm

    Height: 5mm

    Weight:2.4g/5g(include cable)

    Hole diameter: 3mm

    SKU: I2C-GPS
    €30.00
    inc. VAT

     IN STOCK
  • Naze 32 flight control board Full Rev6, magnetometer and barometer

    Naze 32 flight control board Full Rev6, magnetometer and barometer

    The popular Naze32 is here! Initially designed for use with small to mid-sized multirotor craft, it has become the go-to controller for a host of Multirotor projects and propheads.The Full board contains the additional magnetometer and barometer

    Board comes with pins-Not soldered.

    Features:

    Designed for use with small indoor or small to mid-sized outdoor multirotor craft, or as a standalone camera stabilizer, the Naze32 flight control is simple to setup, with configuration based on the familiar “MultiWii” software.

    Specifications:

    •     36x36 mm
    •     5.3 grams (no headers, 7.3 grams with)
    •     2000 degrees/second 3-axis MEMS gyro + accelerometer (MPU6050)
    •     3-axis magnetometer (HMC5883L)
    •     Barometric Pressure sensor (MS5611)
    •     Flexible motor outputs, support various airframe types -
    •     Quad/Hexa/Tri/Bi/Y4/Y6/Octo/Camera Gimbal. (Default is Quad-X)
    •     Up to 8 ch RC input - supports standard receivers (PWM), PPM Sum receiver (FrSky, etc), or Spektrum Satellite receiver.
    •     Built in FrSky telemetry inverter (shared w/main port)
    •     Battery voltage monitoring
    •     Modern 32-bit processor running at 3.3V/72MHz (STM32F103CB).
    •     16Mbit onboard SPI flash
    •     Onboard MicroUSB for setup and configuration
    •     LEDs so bright, they will blind you
    •     MultiWii-based configuration software for easy setup
    •     rev5 hardware

    Included:

    1. Naze32 rev6
    2. 1x RC breakout cable
    3. Case
    SKU: NAZE3010
    €44.00
    inc. VAT

     IN STOCK
  • Naze32 Acro Quadcopter Flight controller

    Naze32 Acro Quadcopter Flight controller

    The Acro Naze32 is one of the best flight controllers available for Multi-rotors.this board is Acro version and not including the Magnetometer and barometer

    This FC features an STM32 32-bit processor and comes in an acro version and and full version. The Naze 32 can be used in many different configurations (up to an octocopter).  It also does FrSky Telemetry, Multiwii serial protocol, and can control a camera gimbal control.

    MCU:ST Microelectronics STM32F103 72-MHz ARM Cortex-M3
    Motion/Position Sensor:Invensense MPU6050 6-DOF MEMS Sensor (3-axis Gyro + 3-axis Accelerometer)
    Compass:none
    Altitude Sensor:none
    Dimensions:36mm x 36mm
    Hole Spacing:30.5mm x 30.5mm
    Weight (bare):6 grams
    Weight (with pin headers):8 grams

    Note that returns on these are not accepted after soldering. Please plug the board into your computer BEFORE you solder it to check it works. 

    SKU: NAZE3009
    €32.00
    inc. VAT

     72HR STOCK
  • NEO M8N 8N GPS for CC3D Revolution Flight Controller

    NEO M8N 8N GPS for CC3D Revolution Flight Controller

    Ublox NEO-M8N GPS  to be used for CC3D Revolution Flight Controller Board , Bulit-in Compass Power Module for RC Multicopter

    Description:

    • NEO-M8N is high precision positioning  and fast search efficiency.
    • The GPS NEO-M8N applies the original M8N chip, which can optimize the module.
    • The built-in electronic compass develops the refresh rate increasing to 10HZ.
    • Openpilot can directly connect CC3D Revolution , GPS interface is generally Main port or Flexi  port .

    Package included:

    1 x Ublox NEO-M8NGPS for CC3DRevolution Controller

    SKU: NEO-M8N-REVO
    €46.00
    inc. VAT

  • NZ32 Micro Brushed Flight Control Board Base NAZE32 6DOF for MICRO FPV

    NZ32 Micro Brushed Flight Control Board Base NAZE32 6DOF for MICRO FPV

    NZ32 Micro Brushed Flight Control Board Base NAZE32 6DOF for MICRO FPV Quadcopter Frame

    • Dimension: 33mm*20mm
    • Thickness: 1.2mm
    • Weight: 4g

    Features:

    • This FC use NAZE32 6DOF hardware, software compatibility with ALIENFLIGHTF1 or NAZE in CleanFlight configurator.
    • NZ32 flight controller use MPU6050 and STM32F103CB micro controller (128Kbytes flash memory, 20Kbytes SRAM, ARM 72Mhz Cortex-M3)
    • The FC use 3oZ 4 lays high quality PCB, support quadrocopter or hexrcopter,
    • Total 6 ways, brushed motor continuous working current up to 6A, onboard 5V
    • Convert 1s battery input to 5V for RX receiver or other equipment , current output 400mA maximum.
    • This 5V/400mA BEC can working reliable when input voltage from 1.8V to 4.35V

    Wire cable colors:
    Blue - PPM
    Red - Sbus
    Yellow - 5V
    Black - GDN

    SKU: NZ32BR
    €22.00
    inc. VAT

     72HR STOCK
  • Openpilot CC3D EVO Flight Controller 32-bit Flexiport New Version (Straight pins)

    Openpilot CC3D EVO Flight Controller 32-bit Flexiport New Version (Straight pins)

    Openpilot CC3D EVO Flight Controller 32-bit Flexiport New Version (Straight pins)

    The CC3D boards is an all-in-one stabilization hardware flight controller, which runs the OpenPilot firmware. It can fly any airframe from fixed wing to an octocopter and is configured and monitored using the powerful and user friendly OpenPilot Ground Control Station (GCS) software.

    The CC3D is an update to the original Copter Control board, now using the powerful single chip IMU. The board shares a lot with the Revolution platform, including the powerful OpenPilot architecture and the cross-platform Ground Control Station (GCS). The CopterControl platform has been designed from the ground up to perform a host of functions from auto-level, multi-copter, Fixed wing UAV’s and even Flybarless Helicopter support. The new included Flexiport provides either I2C connectivity or a second serial port.

    Features:

    •  MultiRotor controller with auto-level, including TriCopters, QuadCopters and HexaCopters
    •  Flybarless Helicopter controller with auto-level
    •  Fixed Wing UAV controller
    •  Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM
    •  3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer
    •  Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
    •  Software support for Windows, Mac and Linux
    •  Direct high speed USB support with no drivers required, a truly plug and play device.
    •  Spektrum satellite receiver support DSM2-DSMX
    •  Futaba S-BUS hardware support and PPM
    •  Innovative Flexi-port technology for superior port flexibility
    •  4Mbits on-board EEPROM for configuration storage

    Specs:

    • Size: 36x36mm
    • Weight: 5.7g
    • Mounting: M3 holes @ 30.5mm square

    Included:

    • CC3D Flight controller Rev C with V4 bootloader pre installed
    • Full cable set to match the onboard ports
    • Damper Mount
    • Reciever antenna mount

     

    SKU: CC3D-EVO-Straight
    €29.90
    inc. VAT

     IN STOCK
  • OpenPilot CC3D EVO Flight Controller, 32-bit Flexiport (New Version)

    OpenPilot CC3D EVO Flight Controller, 32-bit Flexiport (New Version)

    CC3D EVO Hardware Features:

    • Can be directly plugged into the satellite receiver (no conversion cable).
    • Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
    • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
    • Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
    • Software support for Windows, Mac and Linux.
    • Direct high speed USB support with no drivers required, a truly plug and play device.
    • Spektrum satellite receiver support.
    • Futaba S-BUS hardware support.
    • Innovative Flexi-port technology for superior port flexibility.
    • 4Mbits on-board EEPROM for configuration storage.

    Flexiport:

    This flightcontroller also offers an innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.
     
    Superior user experience:

    OpenPilot tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.
     
    OpenPilot software is designed to be used by everybody! All major operating systems are supported and extra packages are also available. The software is all Free software under the GPLv3 license.

    Sensors and Components:

    • 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
    • Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, DSMX satellites, and Futaba S.Bus receivers.
    • Simultaneous support for multiple receivers.
    • ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
    • MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, Spektrum/JR satellites
    • FlexiPort (configurable): serial telemetry, GPS, Spektrum/JR satellites, or I2C peripherals (under development)
    • 10 PWM outputs to servos or ESC’s, or for camera stabilization
    • Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
    • Onboard USB connectivity for easy configuration.
    • USB and serial telemetry and configuration
    • Supported by powerful OpenPilot GCS
    • 4 Mbit onboard memory
    • 3C Quaternion based complementary filter running at 500Hz

    Package Includes:

    • 1 x CC3D EVO Flight Controller
    • 1 x 8pc wire set
    • 1 x 4pc expansion path wire set
    • 1 x Damping Board
    • 1 x Antenna Base

     

    SKU: CC3D-EVO
    €29.90
    inc. VAT

  • OpenPilot CC3D EVO Flight Controller, 32-bit Flexiport w/out Satellite socket

    OpenPilot CC3D EVO Flight Controller, 32-bit Flexiport w/out Satellite socket

    CC3D Hardware Features:

    • Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM.
    • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
    • Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance.
    • Software support for Windows, Mac and Linux.
    • Direct high speed USB support with no drivers required, a truly plug and play device.
    • Futaba S-BUS hardware support.
    • Innovative Flexi-port technology for superior port flexibility.
    • 4Mbits on-board EEPROM for configuration storage.

    Flexiport:

    This flightcontroller also offers an innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs.
     
    Superior user experience:

    OpenPilot tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe.
     
    OpenPilot software is designed to be used by everybody! All major operating systems are supported and extra packages are also available. The software is all Free software under the GPLv3 license.

    Sensors and Components:

    • 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2,
    • Supports several common RC inputs: 6 PWM channels, combined PPM, Spektrum/JR DSM2, DSMJ, and Futaba S.Bus receivers.
    • Simultaneous support for multiple receivers.
    • ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels
    • MainPort functions (configurable): serial telemetry (default), GPS, S.Bus.
    • FlexiPort (configurable): serial telemetry, GPS, or I2C peripherals (under development)
    • 10 PWM outputs to servos or ESC’s, or for camera stabilization
    • Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers.
    • Onboard USB connectivity for easy configuration.
    • USB and serial telemetry and configuration
    • Supported by powerful OpenPilot GCS
    • 4 Mbit onboard memory
    • 3C Quaternion based complementary filter running at 500Hz

    Package Includes:

    • 1 x CC3D
    • 1 x 8pc wire set
    • 1 x 4pc expansion path wire set
    • 1 x Damping Board
    • 1 x Antenna Base

     

    SKU: CC3D
    €24.90
    inc. VAT

  • OpenPilot CC3D Revolution 10DOF STM32F4 Flight Controller Staight Pin

    OpenPilot CC3D Revolution 10DOF STM32F4 Flight Controller Staight Pin

    The OpenPilot Revolution board, also called 'Revo', is a new breed of Autopilot using the STM32F4 series, 210MIPS ARM Micro-controller. This is important, as it contains a hardware floating point unit (FPU), which is a huge advancement for hobby-class autopilots. Of course, OpenPilot has been 32bit since day one, and the FPU is another step up the performance ladder.

    The Revolution is a flight control computer with autopilot, intended for multirotors, helicopters and fixed wings. It is a full 10DOF with gyroscope, accelerometer, magnetometer and pressure sensors.

    Specification:

    • CPU:
      • CPU is the STM32F405RGT6 chip, with ARM Cortex-M4 core at 210MIPS, FPU, and saturation arithmetics DSP functions.
      • The chip features a range of built-in hardware modules that can bo programmed once and function independently, requiring little to no CPU overhead. These include 14x multichanel timers, 3x synchronous-sampling ADC serving up to 24 channels, 2x DAC, matrix memory controller with 16-stream DMA, and other. Communication modules include USB2.0, 3x I2C, 3x SPI, 4x USART, 2x CAN and SIDO. All these modules can be configured for accessing the chip pins using a flexible switch matrix, or disabled to save power.
      • It even contains a real time hardware calendar if you want a wake up flight.
      • The software and settings are loaded through USB connector and no-hassle update function in the GCS (Ground Control Station).
    • Modem: The board features a built-in 433MHz OPLink Modem.
    • Ports: Servo 1-6: These are the PWM outputs that go to servos or electronic speed controllers (ESCs).  Power for the flight controller is typically supplied through these headers from only one of the ESCs, but in most cases, all the servo wires can be left connected. Cutting the pin from servo wires is highly discouraged.  If you feel you must disconnect three of the hot wires, use some shrink tube or electrical tape to insulate the removed pin (you may need that positive voltage at a later date!).  The positive (Vcc) and negative (Gnd) pins are indicated on this diagram and the board. In rare cases, you may need to also disconnect the ground pin if your ESCs are creating ground loop problems (indicated by a general weirdness in setup).
    • Servo output, pin layout:
      • Outside - ground
      • Middle - 5V - 8.4V
      • Inside - signal
    • Flexi-IO Port: The receiver port can act as an input or output port depending on the configuration which is set in the Hardware Settings. Configuring the receiver port as an output port allows the user to assign more output channels then the 6 standard servo outputs.
    • PWM -vs- PPM Recievers: Be aware that not all receivers can be configured to use a PPM output. It is the user's responsibility to research this feature in regards to the desired receiver they wish to use for PPM and ensure it can be used as such. Many hours of frustration can occur while trying to troubleshoot why you can't get your radio to connect to the board with PPM if using a receiver than isn't designed with that feature! Simply make sure the receiver can do it before trying to set it up that way.
    • MainPort: JST-SH 4-pin.
      • This is a serial USART whose baud rate can be adjusted through the GCS. Optionally, Futaba S.Bus receiver, Spektrum/JR satellite receiver or GPS can be mapped to the MainPort. Default configuration is Telemetry for connecting an RF modem.
    • FlexiPort: JST-SH 4-pin.
      • The function of this port also depends on the configuration and can be configured for I2C or Serial. The default configuration doesn't use this port, but it can be used for Telemetry, GPS, Spektrum satellite receivers (all working), and other I2C peripherals (under development).
    • RF Socket: Antenna connection socket for on-board OPLink modem.
    • Pwr Sen/Sonar Port: JST-SH 4-pin.
      • This port can be configured to accommodate an Autopilot current sensor and a low cost Sonar sensor such as the HC-SR04. It can also be used as a general purpose input/output port or as a one or two channel analog input port.  
    • Please note that the output rate on the output channels from the Flexi-IO Port cannot be set individually. If servos are connected to this outputs, you must ensure that they can work with the defined output rate for the bound channel. E.g. if you choose a high output rate to support an octocopter configuration, the update rate from the output channels from the ReceiverPort are bound to the update rate from channels 5 & 6. In this case, you cannot connect analog servo's to these outputs since an analog servo only supports an output rate of 50Hz..

    Package includes:

    • 1 x OpenPilot CC3D Revolution Flight Controller with case
    • 4 x connection cable
    • 1 x 4pin cable
    • 1 x antenna
    SKU: CC3D-REVO
    €79.00
    inc. VAT

     IN STOCK
  • Pixhawk External LED and USB Module

    Pixhawk External LED and USB Module

    The module build in LED and USB on one board. You can use it to connect to Pixhawk. Use the provided four-position DF13 cables and connect to the I2C splitter module to set up a bright, multicolor LED and convenient USB port for your vehicle.

    Included in the set:

    • External USB module
    • External LED module
    • Two four-position DF13 cables (20 cm)
    SKU: PIXHLEDUSB
    €13.00
    inc. VAT

  • Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM MN8 GPS Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM MN8 GPS Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM MN8 GPS Combo for Multicopters

    The board integrates with PX4FMU+PX4IO
    Pixhawk is with new 32 bit chip and sensor technology

    Processor:
    32 bit 2M flash memory STM32F427  Cortex M4, with hardware floating point processing unit
    Main frequency: 256K, 168MHZ RAM
    32 bit STM32F103 backup co processor

    Sensor:
    L3GD20 3 axis digital 16 bit gyroscope
    LSM303D 3 axis  14 bit accelerometer /magnetometer
    MPU6000 6 axis accelerometer / magnetometer
    MS5611 high precision barometer

    Interface:
    5* UART, 1*compatible high voltage, 2*hardware flow control
    2*CAN
    Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
    Futaba SBUS compatible input and output
    PPM signal input
    RSSI (PWM or voltage) input
    I2C
    SPI
    3.3 and 6.6VADC input
    External USB MICRO interface

    Features:
    Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
    Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
    Provide redundant power input and fault transfer function;
    14* PWM/ actuator output;
    Bus interface (UART, I2C, SPI, CAN);
    Provide automatic and manual mode;
    Color LED lamp;
    Multi tone buzzer interface;
    Micro SD to record flight data;

    Package included:

    • 1 x 2.4.8 Pixhawk main control  
    • 1 x Safety switch  
    • 1 x Flight control shell
    • 1 x Buzzer
    • 1 x 6pin to 6pin line  
    • 1 x 4Pin to  4Pin line
    • 1 x 3pin DuPont line
    SKU: Pixhawk-MN8
    €169.00
    inc. VAT

     IN STOCK
  • Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters

    Pixhawk PX4 2.4.8 Flight Controller 32 Bit ARM PX4FMU PX4IO Combo for Multicopters- NO GPS

    The board integrates with PX4FMU+PX4IO
    Pixhawk is with new 32 bit chip and sensor technology

    Processor:
    32 bit 2M flash memory STM32F427  Cortex M4, with hardware floating point processing unit
    Main frequency: 256K, 168MHZ RAM
    32 bit STM32F103 backup co processor

    Sensor:
    L3GD20 3 axis digital 16 bit gyroscope
    LSM303D 3 axis  14 bit accelerometer /magnetometer
    MPU6000 6 axis accelerometer / magnetometer
    MS5611 high precision barometer

    Interface:
    5* UART, 1*compatible high voltage, 2*hardware flow control
    2*CAN
    Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
    Futaba SBUS compatible input and output
    PPM signal input
    RSSI (PWM or voltage) input
    I2C
    SPI
    3.3 and 6.6VADC input
    External USB MICRO interface

    Features:
    Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
    Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
    Provide redundant power input and fault transfer function;
    14* PWM/ actuator output;
    Bus interface (UART, I2C, SPI, CAN);
    Provide automatic and manual mode;
    Color LED lamp;
    Multi tone buzzer interface;
    Micro SD to record flight data;

    Package included:

    • 1 x 2.4.8 Pixhawk main control  
    • 1 x Safety switch  
    • 1 x Flight control shell
    • 1 x Buzzer
    • 1 x 6pin to 6pin line  
    • 1 x 4Pin to  4Pin line
    • 1 x 3pin DuPont line
    SKU: Pixhawk
    €129.00
    inc. VAT

     IN STOCK
  • Power Module for APM- Pixhawk XT60 connectors

    Power Module for APM- Pixhawk XT60 connectors

    Pixhawk- APM Power Module is a simple way of providing your APM/Arduflyer with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6P cable. The on-board switching regulator outputs 5.3V and a maximum of 3A from up to a 6S LiPo battery.

    Features:

    •     Max input voltage: 2~6 LIPO
    •     Max current sensing: 90A
    •     Voltage and current measurement configured for 5V ADC
    •     Switching regulator outputs 5.3V and 3A max
    •     6P molex cable plugs directly to APM/Arduflyer 2.5's 'PM' connector

    Specifications:

    •     Dimension(mm): 25 x 21 x 9
    •     Weight(g): 17(include all wire)
    SKU: PowerModule
    €13.00
    inc. VAT

     IN STOCK
  • QQ SUPER Multi-rotor Flight Control

    QQ SUPER Multi-rotor Flight Control

    QQ SUPER Multi-rotor Flight Control Built-in 3-axis Gyroscope for 4 axis 6 axis KK Upgrade

    Built-in three-axis gyroscope and three-axis acceleration sensor, support for self-stabilizing, super stable flight performance

    Support the general receiver, FUTABA S.BUS receiver, DSM2, DSMX 11MS, DSMX 22MS receiver, simplifying connection installation more convenient, ultra-bright LED

    Product Specifications:

    • Processor:32BIT ARM
    • Voltage:3.6V-8.4V
    • Current:60mA*
    • Output rate:360Hz
    • Dimension(L-W-H):43X29X13MM
    • Weight:13g

    Not include receiver and satelite

    Package includes:

    • 1xQQ super multi-rotor flight controller
    • 1x Chinese Manual
    • 1xEnglish Manual

    SKU: QQ-super
    €23.99
    inc. VAT

     IN STOCK
  • Radiolink AT9 2,4Ghz 9ch with Pixhawk combo, GPS, R9D

    Radiolink AT9 2,4Ghz 9ch with Pixhawk combo, GPS, R9D

    Combo including the following, Save $$$ when buying this perfect combo

    • Radio link AT9 radio with R9D telemetry receiver
    • Pixhawk Radiolink
    • M8N GPS
    • Pixhawk accessories as delivered with the Pixhawk
    SKU: AT9PIXCOMBO
    €259.00
    inc. VAT

     LOW STOCK
  • Radiolink Pixhawk PIX Flight Controller With M8N GPS, Buzzer Combo

    Radiolink Pixhawk PIX Flight Controller With M8N GPS, Buzzer Combo

    Perfect combination of AT9/AT10 and PIX. Super-excellence for ground adjustable parameter.

    The  menu of AT9/AT10 settings was customized for parameter settings of PIX, one to one correspondence, even beginners can set easily!
    Real-time displays attitude, exempt the security risks that caused by forgetting parameter settings.
    Radiolink OSD telemetry module PRM-02 with combinations of AT9/AT10 and PIX, provides the real-time flight information of climbing speed, voltage, GPS information, YAW, RSSI etc and keep track of the flight status. Personal setting of low RSSI alarming.
     
    Customized services, comprehensive technical support, realize RTF(Read to Fly), perfect-experience PIX for powerful function and flying fun.
    Complete installation course, exempted the failure of ground station installation.
    The original parameter setting of PIX with AT9/AT10 if default for quadrocopter, without Mission Planner installation and remote control setting, which simplify the procedure to all-in-one unit and fully enjoy the fun of DIY.
    All-round technical guidance for ESC and motor installation and calibration.
    PIX, with the same components as 3DR and the newest circuit design, more better design to achieve more safer and quieter.  

    On the basis of 3DR PIX function, Radiolink developed optimized circuit design and creative design automation software QA system which help us to decrease the production cost and guarantee the quality and the quantity of the product, after repeatedly over one year test, we achieved less interference of inner components, less noise, more accurate compass and safety while flying, it has a humanized design with a right price.
     
    Comprehensive fine detection for every port of PIX, a new and better experience.
    Each port of every PIX by automated software system comprehensive fine tested, avoiding wrong installation. Never regret.
     
    Easily control any airplanes, switch the Flight Mode as you like. PIXHAWK -- the real king of the open source flight controller made by Radiolink.
    Helicopter, fixed wing, multi-rotor and RC car can be arbitrary collocation.
    Supporting various flight modes, including Acro, Altitude Hold, Auto, Circle, Drift, Guided, PosHold, RTL, Stabilize, Land, Loiter, Sport, Simple and Super Simple Modes.

    Processor

    • 32bit STM32F427 Cortex M4 core with FPU
    • 168 MHz
    • 256 KB RAM
    • Radiolink Pixhawk APM Flight Controller With M8N GPS Buzzer

    Sensors

    • ST Micro L3GD20H 16 bit gyroscope
    • ST Micro LSM303D 14 bit accelerometer / magnetometer
    • Invensense MPU 6000 3-axis accelerometer/gyroscope
    • MEAS MS5611 barometer

    M8N GPS Features:

    1.Top Configuration
    1) GPS decoder chip: Radiolink M8N GPS, with u-blox UBX-M8030(M8), 72-channel, MMIC BGA715L7 from Infineon and 13 years of RF experiences, is much better than single GNSS 7N.
       A.Concurrent reception of GPS/QZSS L1 C/A,GLONASS L10F, BeiDou B1
       B.SBASL1 C/A:WAAS, EGNOS, MSAS
    2) Antenna : 2.5dbI high gain and selectivity ceramic antenna
    3) Power amplify IC: MMIC BGA715L7 from Infineon
    4) Filter: SAWF(Surface acoustic wave filter) form Murata
    5) Geomagnetic: HMC5983 from Honeywell

     Parameter:
    1) Positional Accuracy: 1m precision when working with concurrent GNSS, 2.5m precision when working with single GNSS.
    2) Velocity precision: 0.1m/s
    3) Max height: 50000m
    4) Max speed: 515m/s
    5) Max acceleration: 4G
    6) Max update rate: up to 18Hz
    7) Sensitivity
    Tracking & Nav.: -167dBm; Reacquisition:-163dBm; Cold start:-151dBm; Hot start:-159dBm.
    8)Time to first fix: Cold start: 26s, Hot start:1s.
    9)Connect ports
       Power supply: voltage 3.3VDC+-5%, current 50~55mA
       Ports  
      A.GPS UART interface, baud rate: 1.2K/4.8K/9.6K/19.2K/38.4K/57.6K/112.5K
      B.Geomagnetic I2C interface

    Package Included:
     

    • 1x PIX Flight board
    • 1x Safety switch
    • 1x Buzzer
    • 1x TF card 8G
    • 1x M8N GPS
    • 1x Voltage Current Module
    SKU: RLPIXHAWK
    €169.00
    inc. VAT

     LOW STOCK
  • RJX Brushed F3 EVO Flight Control Board

    RJX Brushed F3 EVO Flight Control Board

    RJX Brushed F3 EVO Flight Control Board Support PPM SBUS receiver Hexacopter LED function 1s 2s battery for Tiny Whoop Mini Micro Nano quad FPV Racing.

    This 32 bit brushed flight control is based on SP RACING F3 EVO firmware.
    Specailly designed circuit ensure 5V output for UART1/2/3 despite 1S or 2S input,receiver output at 3.3V.
    Features STM32F303CCT6 + MPU6500, advanced hardware guarantee more stable flight.
    Support battery voltage monitor, buzzer and led function.
    Support basically all coreless motors available, including 1020 motor.
    Large current NMOS transistors enable the board to sustain up to 10A operating current per channel. Each channel is equipped with a freewheeling diode.
    Go to UART3 in cleanflight to configurate.
    PPM and SBUS receiver soldered to the UART2, Go to UART2 for SBUS configuration.
    Dimensions:22MM * 32.5MM, thickness: 1.2MM.
    Note: The propeller must be removed during configuration F3 EVO 1.13.0 firmware by default, if you need to reflash, please input "set motor_pwm_rate = 1000" in the Cleanflight configuration software and save!

    Specification:

    • Micro size 22mm*32.5mm,weight 3g.In support of the world almost all hollow cup motor,including 1020 coreless motor.
    • Based on F3 flight controller , Specially designed and built for quads around 100mm and sub 100mm class. Support Quadcopter and Hexacopter, LED function.
    • Features STM32F303CCT6 + MPU6500, advanced hardware guarantee more stable flight.
    • Support for PPM, SBUS, DSM receiver, Support battery voltage monitor and buzzer function.
    • Support 1S (3.7--4.2V) and 2S (7.4--8.4V) lipo battery,with 2s, you could get even more fierce racing experience than 1s. Note: the minimum voltage power that supports the borad to work normally is more than 4.8V.

    Note: 1s battery can only offer 3.7V power, the minimum voltage power that supports the borad to work normally is more than 4.2V.

     

    SKU: RJX1309
    €22.90
    inc. VAT

     IN STOCK
  • Seriously Dodo Flight Controller board

    Seriously Dodo Flight Controller board

    DO DO Flight controller Board: Seriously, do you want more from your flight controller? The DoDO is your answer!

    Features:

    •     8 input channels
    •     8 output channels
    •     3 UARTs (GPS, Telemetry, S.bus)
    •     2-6s input power
    •     5v output - 0.5A Max (No more external regulators to get in your way!)
    •     stm32 f303 **NEW STM32F3 CPU WILL SUPPORT LOWER LOOPTIMES**
    •     16mbit dataflash  **2 MEGABYTES OF STORAGE FOR DATA LOGGING**
    •     Barometer
    •     Spektrum satellite port (Connector not included)
    •     MPU6050 accelerometer/gyro
    •     36x36mm board with 30.5mm mounting holes (Same as CC3D, Naze32)
    •     5.4g
    •     MicroUSB socket
    •     Dedicated connector for WS2811-style LEDs
    •     Operates on Cleanflight
    •     Will accept S.BUS connection directly with no inversion or hacks.

     

    SKU: DODOFC
    €55.00
    inc. VAT

  • SP Racing F3 Flight Controller Acro version for racing/acro flying 6 DOF

    SP Racing F3 Flight Controller Acro version for racing/acro flying 6 DOF

    The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you're into FPV racing, acrobatic flying or aerial photography it's perfect. Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.

    Acro Version have 6 DOF while Deluxe version has 10 DOF, including Barometer and Compass: Additional sensors for altitude and direction

    The SPRacingF3 runs the open-source Cleanflight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.

    Cleanflight comes with a detailed manual that is reviewed and maintained by the Cleanflight developers and community. No more out-of-date wiki pages and second-hand information.

    Features

    •     Practical - Easy to access connectors and solder pads.
    •     Configurable - Choose to use connectors, solder pads or pins.
    •     Stackable - Mount to your PDB or OSD.
    •     Compact - Only 36x36mm.
    •     Professional - Symmetrical, Neat and Tidy.
    •     8 Dedicated PWM outputs
    •     8 PWM Inputs
    •     36 I/O Connections
    •     72Mhz Clock Speed
    •     3 Hardware Serial Ports
    •     64Mb Flash Storage

    Specifications (Acro Version)

    The hardware was designed by the lead developer of Cleanflight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the Cleanflight users, contributors and top-pilots.

        36x36mm board with 30.5mm mounting holes
        Weight ~6 grams
        Acro version is without Compass and Barometer Sensors
        STM32F303 CPU, 72Mhz inc FPU
        High-Capacity Flash (Acro and Deluxe)
        MPU6050 accelerometer/gyro
        MicroUSB socket
        2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
        8x 3pin though-holes for pin headers for ESC/Servo connections
        2x 4pin though-holes for pin headers for 2x serial ports
        1x 2pin though-holes for pin headers for battery voltage
        1x 2pin though-holes for pin headers for buzzer
        1x 4pin JST-SH socket for I2C
        1x 4pin JST-SH socket for SWD debugging

    Flight Performance

        The SPRacingF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails.

    No-Compromise I/O

        Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!

    Configurable

        The SPRacingF3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).

    Tiny and lightweight

        The SPRacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

    Flight Logging

        On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

    Next-Generation CPU

        The SPRacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time.
        Loop times up to ~2x as fast as previous-generation STM32F1 based boards.

    Developer Friendly

        Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

    OneShot ESC

        Full support for OneShot ESCs for easy PID tuning and a sharper response.

    Broad RC receiver Support

        Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).

    Programmable LED

        Dedicated output for programmable LEDs - great for orientation, racing and night flying.

    Battery Monitoring

        Battery monitoring ports for voltage and current.

    Sonar

        Sonar support for precision low-altitude hold.

    I2C Port

        I2C port always powered, perfect for external sensors or always-on OLED Screen.

    Buzzer

        Buzzer port for audible warnings and notifications.

     

    SKU: SPRF3ACR
    €44.00
    inc. VAT

     IN STOCK
  • SP Racing F3 Flight Controller Deluxe version 10 DOF for Multicopter, Compass, Barometer

    SP Racing F3 Flight Controller Deluxe version 10 DOF for Multicopter, Compass, Barometer

    SPRacing F3 Flight Controller Deluxe Version runs Cleanflight and suits the Drone Racers who need all the features that have been specially designed for racing.

    SP Racing F3 Flight Controller (SPRacingF3) has been designed to deliver incredible flight performance based on proven and tested sensors while additionally providing unparalleled and I/O capabilities in a small and extremely lightweight form-factor using a next-generation CPU.

    Acro Version have 6 DOF while Deluxe version has 10 DOF, including Barometer and Compass: Additional sensors for altitude and direction

    The SP3 Controller is favoured amongst some of the top pilots for its performance , reliability and black box recordings .

    Flight Performance - The SPRacingF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails.

    Flight Logging - On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

    Developer Friendly - Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader.

    No-Compromise I/O - Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time!

    Tiny and Lightweight - The SPRacingF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

    Next Gen CPU - Full support for OneShot ESCs for easy PID tuning and a sharper response.

    Broad RC Receiver Support - Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).

    Battery Monitoring - Ports to enable monitoring of voltage and current.

    12C Port - I2C port always powered, perfect for external sensors or always-on OLED Screen.

    Programmable LED - Dedicated output for programmable LEDs - great for orientation, racing and night flying.

    Buzzer - Buzzer port for audible warnings and notifications.

    Specifications of the Flight Controller.

    •     36x36mm board with 30.5mm mounting holes
    •     Weight ~6 grams
    •     STM32F303 CPU, 72Mhz inc FPU
    •     High-Capacity Flash (Acro and Deluxe)
    •     MPU6050 accelerometer/gyro
    •     MS5611 barometer (Deluxe only)
    •     HMC5883 compass (Deluxe only)
    •     MicroUSB socket
    •     2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
    •     8x 3pin though-holes for pin headers for ESC/Servo connections
    •     2x 4pin though-holes for pin headers for 2x serial ports
    •     1x 2pin though-holes for pin headers for battery voltage
    •     1x 2pin though-holes for pin headers for buzzer
    •     1x 4pin JST-SH socket for I2C
    •     1x 4pin JST-SH socket for SWD debugging

    Package including Case, Pins, Cables for connections

    SKU: SPRF3DL
    €49.90
    inc. VAT

     IN STOCK
  • SP Racing F3 Flight Controller Integrate OSD with Protective Case for FPV Multicopter

    SP Racing F3 Flight Controller Integrate OSD with Protective Case for FPV Multicopter

    The SPRacingF3 gives you all the features you need for the heart of your aircraft, whether you're into FPV racing, acrobatic flying or aerial photography it's perfect. Supports a variety of aircraft, tricopters, quadcopters, hexacopters, octocopters, planes and more.

    This version is Acro Version, the pinS ARE NOT soldered

    Specification:     

    - 36x36mm board with 30.5mm mounting holes
    - STM32F303 CPU, 72Mhz inc FPU
    - High-Capacity Flash (Acro and Deluxe)
    - MPU6050 accelerometer/gyro

    - 2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
    - 1x 4pin JST-SH socket for SWD debugging
    - 1x 5pin JST-SH socket for Flash firmware and Configuration (Connect to the CP2104 uart to usb tool)
    - 8x 3pin though-holes for pin headers for ESC/Servo connections
    - 4x 2pin though-holes for pin headers for 1x serial port and i2c port
    - 8x 1pin though-holes for pin headers for battery voltage/buzzer/Video in/Video out

    Package included:
    - 1 x SP Racing Acro Version flight controller integrate OSD
    - 1 x Protective case
    - 1 x Programmer
    - 4 x Connection cable
    - Pins

    SKU: SPRF3OSD
    €42.00
    inc. VAT

     IN STOCK
  • Spedix CC3D Flight Controller

    Spedix CC3D Flight Controller

    Features:

    • One of the most popular open source multirotor flight controller developed by Open Pilot team
    • Redesigned and manufactured by Spedix to improve connectivity. No adapter is required to setup DSM2/DSMX satellites and S.Bus receivers
    • Optimized ESC pins directions to make wiring in a neat way. No ESC wires come from the two sides of a multirotor frame
    • Assembled in the factory with protection case

    Specifications:

    • Input Voltage: 4.8-6.0V
    • Dimensions:39x39x12mm
    • Weight: 14g
    • Firmware Version:15.02

    Contents:

    • CC3D controller with case (1x)
    • Cable set (1x)
    SKU: SPX71004
    €19.90
    inc. VAT

     LOW STOCK

Manufacturers

Back