Flybarless controllers

Flybarless controllers

Flybarless combos and controllers

Products


  • VBar NEO 6.1 Express- Only with Heli kit

    VBar NEO 6.1 Express- Only with Heli kit

    Save money on VBar NEO 6.1 Express, purchased only together with kit

    this item doesn't qualify for any double discounts

    SKU: MIK-49451
    €175.00
    inc. VAT

     72HR STOCK
    SALE
  •  Governor Sensor MICROBEAST Plus

    Governor Sensor MICROBEAST Plus

    • Suitable for T-REX 600N / T-REX 700N
    • Must use with:
    - BEASTX MICROBEAST Plus Flybarless System

    Content
    • 1x Beastx Governor Sensor (255mm/6pin connector)
    • 2x RPM Magnet (4x1.6mm)

    SKU: HEGBP001
    €9.99
    inc. VAT

     LOW STOCK
  • Align MiniGRS Flybarless System

    Align MiniGRS Flybarless System

    Align MiniGRS Flybarless System

    Special design for ALIGN small helicopters. It's light and simple.
    Support the latest new ALIGN A10 Radio (10-channel/A.BUS system) for the best working operation.
    Support T-REX 250/450/470/500 models, no need to setup, outstanding flight performance for the beginner or 3D pilot.
    Support JR DSM2 and Spektrum DSM2/DSMX satellite. Built-in Futaba S-FHSS 2.4GHz support for Futaba S-FHSS transmitter.

    Specification:

    • Operating voltage range: DC 3.5~8.4V
    • Operating current consumption: <100mA @ 4.8V
    • Rotational detection rate: ±300°/sec
    • Rudder yaw detection rate: ±600°/sec
    • Sensor resolution: 12 BIT
    • Swashplate Support: 120° CCPM Swashplate
    • Mode Support: T-REX250, T-REX450, T-REX470, T-REX500
    • Receiver Support: ALIGN A10(A.BUS), Futaba S-FHSS, DSM2/DSMX
    • Operating temperature: -20° ~ 65°
    • Operating humidity: 0% ~ 95%
    • Comply with RoHS
    • Size: 37.6x22.4x13mm

    Accessories:

    • MiniGRS electronics board set x 1
    • MiniGRS Signal Wire x 1
    • MiniGRS Binding Plus x 1
    • Plastic flat screwdriver black x 1
    • Double Sided Tape x 1

     

    SKU: HEGGRS01
    €87.00
    inc. VAT

  • BavarianDemon 3SX, 3X & Cortex Cable loom L150

    BavarianDemon 3SX, 3X & Cortex Cable loom L150

    BavarianDemon 3SX, 3X & Cortex Cable loom L150

    1 pcs. cable loom, 150mm
    Suitable for 3SX, 3X and CORTEX

    (1 pc. included in the delivery of the systems. Only as an accessory if the original is not suitable.)

    SKU: BD-CABLE-LOOML150
    €18.90
    inc. VAT

     72HR STOCK
  • BavarianDEMON 3X Flybarless system for Helicopters

    BavarianDEMON 3X Flybarless system for Helicopters

    3X: The worlds best 3-axis flybarless system
    Ideal for demonic 3D maneuvers
    Absolute stability, also in large scale helicopters

    FACTS & FEATURES:

    • Symmetric torque control
    • Usable in all types of flybarless RC helicopters
    • Supports all current servo and swashplate types as well as virtual swashplate rotation
    • CNC- milled aluminum housing
    • Various installation options, horizontal or vertical
    • Intelligent setup wizard
    • Real Time-Tuning for optimization of parameters in flight
    • Online up-datable
    • Internal swashplate mixer
    • Ultra-fast tail rotor gyro

    PRODUCT DESCRIPTION:

    The bavarianDEMON 3X is especially aimed at extreme 3D pilots, but also works X-extremely well for all other flybarless helis. Latest software algorithms, intelligent sensor technology combined with an unprecedented power, all this fitting the entire range of flybarless helicopters, electric, nitro, gaser and turbine powered. Because they are lighter, helicopter models without flybar are much more agile and maneuverable, and are approx. 15% more powerful. In combination with the bavarianDEMON 3X , huge performance is delivered, without the need to adjust the fragile flybar mechanism.

    Included

    • Main sensor unit including mounting pads
    • Cable loom for receiver connection
    • USB lead for direct connection to PC / Notebook
    • Firmware update via web

     

    SKU: BD8590
    €195.00
    inc. VAT

     LOW STOCK
  • BavarianDEMON AXON Bluetooth Flybarless controller

    BavarianDEMON AXON Bluetooth Flybarless controller

    Especially developed for all kind of RC helicopter, the AXON combines all State-of-the-Art features, without leaving a simple handling behind – primarily including the soon available Android- & iOS-Apps via Bluetooth. As one of the most important details when out at the flying field is the intuitive and easy handling and tuning of all parameter without the need of a PC or separate programming unit.

    •     Ultra-precise flight control
    •     Latest 32-bit technology
    •     Multiple Horizon- and Rescue modes
    •     3 bank sets
    •     Integrated governor (electric and gaser/nitro)
    •     Intelligent vibration analysis
    •     Android & iOS App Multi protocol input
    •     Future-proof via online update
    •     Prepared with sensor bus

    WHAT'S IN THE BOX

    •     AXON main unit
    •     Double-sided mounting tape, one each of ‚Acro‘ ACP and ‚Soft‘ ACP
    •     Cable loom to receiver (150mm)
    •     Mini USB cable Product information
    SKU: AXON
    €349.00
    inc. VAT

     LOW STOCK
  • BavarianDEMON CORTEX controller for Airplanes

    BavarianDEMON CORTEX controller for Airplanes

    New 3-axis stabilization system for fix wing model aircraft
    Extremely smooth flight characteristics - even in strong, gusty wind
    Faster training - Adjustable gyro assistance – Precise flight

    FACTS & FEATURES:

    • Easy to Run: simply read in your current control signals – ready
    • No PC necessary

    Supports:

    • 2 ailerons
    • 2 elevators
    • 1 rudder
    • Supports various receiver systems:
    • S.Bus (receipt)
    • Spektrum/JR satellites (up to 2 sats)
    • Jeti-/PWM-/PPM sum signal
    • Conventional receivers
    • Software and firmware updates via web


    The bavarianDEMON CORTEX is a stabilization system for fix wing model aircraft. And hence an absolute world first in this form.  The new brain and heart of your high-quality aircraft – immediately ready to run.  The CORTEX does not require any PC or additional software settings - unless it is desired. The CORTEX comes with a sensor unit, connection cable harness, adhesive pads, USB connection cable and exclusive design and information material from your favourite demon. There are software and firmware updates conveniently on the web. But the most important thing is the demon inside. Since it means pure flight fun with the greatest possible carelessness. No or hardly any more additional spending due to crashes. You will train faster with the CORTEX whereby the adjustable stop level helps. However and primarily for experienced pilots or demons among you, the CORTEX is indispensable from now on.

    Included

    • Main sensor unit including mounting pads
    • Cable loom for receiver connection (90mm)

    Optional accessory :USB lead for direct connection to PC / Notebook

    SKU: BD8593
    €259.00
    inc. VAT

     IN STOCK
  • BavarianDEMON Cortex PRO 3-axis Gyro for RC Planes

    BavarianDEMON Cortex PRO 3-axis Gyro for RC Planes

    BavarianDEMON Cortex PRO 3-axis Gyro for RC Planes

    The CORTEXpro opens up the next generation gate with even more demonic features and fun factors. Based on the latest 32-bit CPU technology and in addition to all state-of-the-art features, the brand new CORTEXpro offers a bunch of great news for more comfort in flight and setup. The combination of easy programming and basic setup without software, automatic signal type detection, compatibility with invariably all common analog and digital serial protocols, as well as the dual and redundant serial input and output option, is absolutely unique.

    Let the DEMON take control over your cockpit and test the new CORTEXpro now! More fun, more safety, more comfort – presumably only your breath will backpedal…

     
    Features:

    • Multi protocol input and output
    • Latest 32-bit technology
    • Up to 24 channels, 16 stabilized
    • Receiver redundancy for 2 inputs
    • iOS & Android App for fine tuning
    • Easy teach-in via Tx
    • No software needed

     

    SKU: CORTEXPRO
    €299.00
    inc. VAT

     LOW STOCK
  • BavarianDEMON USB PC connection lead for setting up

    BavarianDEMON USB PC connection lead for setting up

    BavarianDEMON USB PC connection lead for setting up and storing all parameters and options.

    Also provides a possibility of transfering complete (pre-programmed) settings into and from the bavarian DEMON.

    The required USB cable is already part of the scope of supply. The PC ... Only connect the PC adapter the PC after the setup software has been installed

    SKU: BD92774
    €25.90
    inc. VAT

     IN STOCK
  • BEASTX 8cm Receiver Adapter- BX76002

    BEASTX 8cm Receiver Adapter- BX76002

    BEASTX Receiver Adapter Cable 8cm-BX76002

    SKU: BTXA76002
    €9.90
    inc. VAT

     IN STOCK
  • BEASTX MICROBEAST PLUS HD Pro Edition

    BEASTX MICROBEAST PLUS HD Pro Edition

    MICROBEAST PLUS HD Pro Edition is a 3-axis control system for flybarless RC model helicopters. MEMS sensors of the latest generation measure the aircraft′s rotational movement with unprecedented precision and transmit the data digitally and in real time to the system.
    The housing made of plastic composite material keeps the weight of MICROBEAST PLUS sensationally low.

    The sophisticated setup can quickly be done everywhere and no expensive programming box or computer is needed. So many settings can also be changed simply and easily at the flying field.
    Further options are available with the optional USB2SYS interface and the StudioX software package. MICROBEAST PLUS can be kept up to date by using the update functionality and advanced pilot can thus customize the unit specifically to their needs.

    The device comes with Firmware ProEdition: Additional to basic functionality as flybarless and tail gyro system, an internal RPM Governor function for helicopters with electric or combustion drive is included as well as the AttidudeControl function which can level the helicopter automatically. This allows to activate different training aids like bail out rescue mode, 3D-Mode or flight trainer mode.

    This version is designed as "Heavy Duty" version of MICROBEAST PLUS Pro Edition with an additional switchable high power input. It is particularly suitable for helicopters with standard sized servos and it reflects today‘s requirements for power supply like never before. The power supply port is realized by a well proven, high-quality connector. By using the included switch, the system can be activated electronically and remains operational even if the switch is disconnected by accident. Due to this fact the high power connection may be used without the switch at all. MICROBEAST PLUS HD has a housing in aluminum composite construction.

    Governor mode :

    The RPM Governor can be used for electric and nitro helicopters. It has built in soft start and autorotation bail out function. The control it quite similar to electric speed controllers with governor function, so you simply set your throttle curves as switches for "motor off", "headspeed 1", "headspeed 2" and "autorotation bailout".
    Adjusting complex throttle curves is not necessary anymore and the helicopter will maintain the specified rotor head speed over the whole flight. Optional the nitro governor can be also used in classic style with throttle curves and a separate switch for governor/rpm control.

    Attitude Control :

    "Attitude Control" offers different modes of self leveling. These are "Bailout rescue mode", "3D-Mode" and "Flighttrainer mode" with angular limitation. Basically when you activate the Attitude Control it will turn your helicopter back to level position when you release the sticks.
    Some modes additionaly apply collective pitch input and lock your thrust stick in the ground direction. So the unit will turn your helicopter and keep it leveled in hovering flight regardless of how the pilot moves the stick.

    Try everything and improve your skill with Microbeast Plus HD Pro Edition !

    Specifications:
    Input voltage : 3,5 V - 8,5 V DC (Operation with 2 cell LiPo possible)
    Processor : 32 Bit ARM
    Sensor : 6-Axis MEMS (Gyro + Accelerometer)
    Dimensions : 36 x 25 x 21mm
    Weight (w/o wiring) : 19g

    Servo center pulses:
    Swashplate: 1520µs
    Rudder: 1520µs, 960µs, 760µs

    Servo pulse rates:
    Swashplate: 50 - 200Hz
    Rudder: 50 - 560Hz

    Swashplate mixing:
    mCCPM, eCCPM: 90, 120, 135, 140
    Swash phasing (by using StudioX)

    Input signals:
    Single channels
    PPM serial pulse
    SRXL (JR XBus, SUMD, M-Link...)
    Futaba S.Bus/S.Bus2
    Spektrum Remote Receiver* (DSM2/DSMX) * with Spektrum Remote Receiver adapter

    In the box :

    MICROBEAST PLUS HD Pro Edition
    Switch harness
    Power cable
    Receiver connection cables
    3M adhesive pads
    Adjustment tool
    Printed instruction manual

    Accessories:
    USB2SYS Interface
    Spektrum Remote Receiver adapter

    SKU: BXM76500PE
    €249.00
    inc. VAT

     72HR STOCK
    NEW
  • BeastX Microbeast Receiver Adapter Cable 15cm

    BeastX Microbeast Receiver Adapter Cable 15cm

    Set of long receiver wiring leads for the MICROBEAST flybarless system.

    Length of 15cm and intended to be used to connect the MICROBEAST to your receiver.

    Package includes:

    • 3 multi conductor receiver leads, each 15cm in length.
    SKU: BTXA76006
    €9.90
    inc. VAT

     IN STOCK
  • BeastX Spektrum Satellite Adaptor

    BeastX Spektrum Satellite Adaptor

    BeastX Spektrum Satellite Adaptor BXA76009

    SKU: BXA76009
    €18.50
    inc. VAT

  • BLE2SYS Microbeast Bluetooth Interface

    BLE2SYS Microbeast Bluetooth Interface

    BLE2SYS Microbeast Bluetooth Interface

    Simply set your Microbeast parameters with your smartphone through BLE2SYS Bluetooth Smart Interface.

    Specifications:

    • Weight: 2,9g
    • Dimensions: 42,5x16x4,5mm

    In the box:

    • BLE2SYS Bluetooth Interface x1
    • 10cm wire (JR connector) x1
    SKU: BXA76015
    €69.00
    inc. VAT

     LOW STOCK
  • Futaba GYA460 Gyro - 6-Axis Flight Control (Aero)

    Futaba GYA460 Gyro - 6-Axis Flight Control (Aero)

    The new Futaba GYA460 is a 6 axis aircraft gyro which includes automatic flight attitude control and stabilisation. As well as having 3 independent gyros the GYA460 also features 3 acceleration sensors for attitude correction. With the GYA460 in operation the aircraft will maintain a stable attitude, whatever the wind conditions, enabling the pilot to enjoy flying the model instead of fighting the conditions.

    In beginner mode the maximum roll, pitch or yaw angle is limited to about 80°, and in the event of loss of control, the pilot can simply release the transmitter stick and the model will automatically recover into level flight. When the unit is in gyro mode, this recovery feature is disabled, allowing the model to carry out the full range of aerobatic manoeuvres, whilst gaining the stability and smoothness the 3 gyros bring

    With the gyro switch off model relies entirely on the skill of the pilot.

    The GYA460 is suitable for models with 2 aileron servos as well as Deltas or other models with elevons.

    Specifications:

    • 6-axis Flight Stabilisation
    • HV compatible
    • S-Bus or PWM connection options
    • 3 Flight modes
    • Beginner mode with emergency function
    • Elevon compatible

    Content:

    • GYA460
    • Connection lead PWM
    • Mounting pad
    • Mini screwdriver
    SKU: P-GYA460
    €99.00
    inc. VAT

     72HR STOCK
  • Gyroscope VBar Blueline

    Gyroscope VBar Blueline

    Gyroscope VBar blueline

    SKU: MIK-04157
    €165.00
    inc. VAT

     72HR STOCK
  • IKON FLYBARLESS SYSTEM

    IKON FLYBARLESS SYSTEM

    Ikon system- if not availiable, we will deliver the MSH brain instead.
    SKU: IKN1001
    €230.00
    inc. VAT

     72HR STOCK
  • MICROBEAST PLUS Flybarless Stabilization controller

    MICROBEAST PLUS Flybarless Stabilization controller

    MICROBEAST PLUS is based on the popular MICROBEAST and starts the next level of the BEASTX flybarless revolution. MEMS sensors of the latest generation measure the aircraft‘s rotational movement with unprecedented precision and transmit the data digitally and in real time to the control system. These new sensors are insensitive to typical vibrations of a model helicopter. The housing made of plastic composite material keeps the weight of MICROBEAST PLUS sensationally low.

    Box contents (MICROBEAST PLUS):

    MICROBEAST PLUS
    Receiver connection cables
    3M adhesive pads
    Adjustment tool
    Printed instruction manual

    MICROBEASTPLUS and MICROBEASTPLUSHD work with the world‘s proven EasySetup of BEASTX. The sophisticated setup can quickly be done everywhere and no expensive programming box or computer is needed. So many settings can be changed simply and easily at the flying field.

    Further options are available with the optional USB2SYS in­ter­face and the StudioX software package. MICROBEAST PLUS can be kept up to date by using the update functionality and advanced pilot can thus customize the unit specifically to their needs.

    Specifications:

    • Input voltage  :3,5 V - 8,5 V DC (Operation with 2 cell LiPo possible)
    • Processor: 32 Bit ARM
    • Sensor :6-Axis MEMS (Gyro + Accelerometer)
    • Dimensions :36 x 25 x 14 mm
    • Weight (w/o wiring) : Approx 11g

    Features:

    • Servo center pulses:
    • Swashplate: 1520µs
    • Rudder: 1520µs, 960µs, 760µs

    Servo pulse rates:

    • Swashplate: 50 - 200Hz
    • Rudder: 50 - 560Hz

    Swashplate mixing:

    • mCCPM, eCCPM: 90, 120, 135, 140
    • Swash phasing (by using StudioX)

    Input signals:

    • Single channels
    • PPM serial pulse
    • SRXL (JR XBus, SUMD, M-Link...)
    • Futaba S.Bus/S.Bus2
    • Spektrum Remote Receiver* (DSM2/DSMX)
    • * with Spektrum Remote Receiver adapter
    SKU: BXM76400
    €139.90
    inc. VAT

     LOW STOCK
  • MICROBEAST PLUS HD Flybarless Controller

    MICROBEAST PLUS HD Flybarless Controller

    MICROBEAST PLUS HD is designed as „Heavy Duty“ version of MICROBEAST PLUS with an additional switchable high power input. It is particularly suitable for helicopters with standard sized servos and it reflects today‘s requirements for power supply like never before. The power supply port is realized by a well proven, high-quality connector. By using the included switch, the system can be activated electronically and remains operational even if the switch is disconnected by accident. Due to this fact the high power connection may be used without the switch at all. MICROBEAST PLUS HD has a housing in aluminum composite construction.

    MICROBEAST PLUS HD

    • Input voltage: 3,5 V - 8,5 V DC (Operation with 2 cell LiPo possible)
    • Processor: 32 Bit ARM
    • Sensor: 6-Axis MEMS (Gyro + Accelerometer)
    • Dimensions: 36 x 25 x 21mm
    • Weight (w/o wiring): ca. 19g

    Features:

    • Servo center pulses:
    • Swashplate: 1520µs
    • Rudder: 1520µs, 960µs, 760µs

    Servo pulse rates:

    • Swashplate: 50 - 200Hz
    • Rudder: 50 - 560Hz

    Swashplate mixing:

    • mCCPM, eCCPM: 90, 120, 135, 140
    • Swash phasing (by using StudioX)

    Input signals:

    • Single channels
    • PPM serial pulse
    • SRXL (JR XBus, SUMD, M-Link...)
    • Futaba S.Bus/S.Bus2
    • Spektrum Remote Receiver* (DSM2/DSMX)
    • * with Spektrum Remote Receiver adapter


    Box contents:

    • MICROBEAST PLUS HD
    • Switch harness
    • Power cable
    • Receiver connection cables
    • 3M adhesive pads
    • Adjustment tool
    • Printed instruction manual
    SKU: BXM76500
    €159.90
    inc. VAT

     LOW STOCK
  • MICROBEAST PLUS PRO-EDITION Flybarless controller

    MICROBEAST PLUS PRO-EDITION Flybarless controller

    MICROBEAST PLUS is based on the popular MICROBEAST and starts the next level of the BEASTX flybarless revolution. MEMS sensors of the latest generation measure the aircraft′s rotational movement with unprecedented precision and transmit the data digitally and in real time to the control system.
    These new sensors are insensitive to typical vibrations of a model helicopter. The housing made of plastic composite material keeps the weight of MICROBEAST PLUS sensationally low.

    MICROBEAST PLUS and MICROBEAST PLUS HD work with the world′s proven EasySetup of BEASTX. The sophisticated setup can quickly be done everywhere and no expensive programming box or computer is needed. So many settings can be changed simply and easily at the flying field.

    Further options are available with the optional USB2SYS in-ter-face and the StudioX software package. MICROBEAST PLUS can be kept up to date by using the update functionality and advanced pilot can customize the unit specifically to their needs. StudioX for Windows & Mac is available for download at www.beastx.com.


    Additional features of PRO EDITION
    Governor
    AttitudeControl*

    *) AttitudeControl contains following functions:

    • Rescue mode (with/without extra pitch)
    • 3D-mode (with/without extra pitch)
    • Hover trainer

    Specifications

    • Input voltage: 3,5 V - 8,5 V DC (Operation with 2 cell LiPo possible)
    • Processor: 32 Bit ARM
    • Sensor: 6-Axis MEMS (Gyro + Accelerometer)
    • Dimensions: 36 x 25 x 14 mm
    • Weight (w/o wiring): ca. 11g

    Features

    • Servo center pulses:
    • Swashplate: 1520µs
    • Rudder: 1520µs, 960µs, 760µs

    Servo pulse rates:

    • Swashplate: 50 - 200Hz
    • Rudder: 50 - 560Hz

    Swashplate mixing:

    • mCCPM, eCCPM: 90, 120, 135, 140
    • Swash phasing (by using StudioX)

    Input signals:

    • Single channels
    • PPM serial pulse
    • SRXL (JR XBus, SUMD, M-Link...)
    • Futaba S.Bus/S.Bus2
    • Spektrum Remote Receiver* (DSM2/DSMX)  * with Spektrum Remote Receiver adapter

    Content

    • MICROBEAST PLUS PRO-EDITION
    • Receiver connection cables
    • 3M adhesive pads
    • Adjustment tool
    • Printed instruction manual


    Optional Accessories:

    • USB2SYS Interface
    • Spektrum Remote Receiver adapter
    SKU: BXM76400PE
    €249.00
    inc. VAT

     72HR STOCK
  • MICROBEAST Special adhesive foam tape (4pcs)

    MICROBEAST Special adhesive foam tape (4pcs)

    MICROBEAST Special adhesive foam tape, 4 pcs in pack

    SKU: BXA76008
    €3.50
    inc. VAT

     IN STOCK
  • MICROBEAST Tail Gyro Adapter Cable

    MICROBEAST Tail Gyro Adapter Cable

    MICROBEAST Tail Gyro Adapter Cable

    SKU: BXA76001
    €9.50
    inc. VAT

     IN STOCK
  • Mikado Current/Voltage/Capacitysensor for VBar Control

    Mikado Current/Voltage/Capacitysensor for VBar Control

    Mikado Current/Voltage/Capacitysensor for VBar Control

    Hardware Features of the Current/Voltage/Capacity Sensor for flight packs:

    • Individually precision calibrated
    • Optocoupler
    • Reverse battery protection
    • No influence from motor or current carrying wires

    Software Features:

    • Direct displaying from voltage and capacity
    • Max. current and min. voltage storage
    • Logfile data from the flight
    • Battery Logbook with names
    • Adjustable capacity, residual capacity and voltage for each battery
    • Residual capacity is shown as bar in the radio display
    • Overdischarge Warning
    • Warning at use of not fully charged batteries
    • Loud speaker announcement for reducing battery capacity

    Notes:
    Requires a VBar with Spektrum Satellite connectors (telemetry bus for VBar Control)
    Not suitable for measuring receiver packs only (e.g. on a nitro heli)
    extracted capacities are not added up, measurement only on a per-flight basis

    Specifications:

    • Current Consumption     2.5 mA
    • Working Temperature Range     -5 to 50 °C, 23 to 122 °F
    • Dimensions     approx. 20 x 20 x 10 mm
    • Power Rating     120 A continuous, 330 A peak
    • Effective Range (current)     0.1 A to 300 A
    • Effective Range (voltage)     5 V to 100 V (2s to 16s LiPo)
    • Resolution     0.01 A / 0.01 V

    Contents:
    Device   Voltage/Current Sensor with connecting wires to battery and ESC
    Connecting Wire     Sensor wire 500 mm

    Accessories:

    • Connecting Wire 250 mm     04898
    • Connecting Wire 500 mm     04899
    • Battery ID Reader     04907
    • Battery ID Tags (10 pc.) 04908
    • Miscellaneous
    SKU: MIK-4890
    €74.90
    inc. VAT

     72HR STOCK
  • Mikado Protection Case for VBar NEO

    Mikado Protection Case for VBar NEO

    Protection Case for VBar NEO

    SKU: MIK-05005
    €13.50
    inc. VAT

     LOW STOCK

Manufacturers

Back