Other Motors

 800MX features high efficiency, superior power, excellent torque, low current draw and low temperature; it’s capable of maintaining consistent torque and head speed through continuous 3D maneuvers.
Due to the 800MX’s high efficiency and low current draw, the standard equipment 120A electronic speed controller are sufficient to experience the power of this motor, and extend battery longevity.
800MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.
The 800MX motor armature are dynamically balanced to eliminate typical imbalance found in other outrunner motors.
Maintenance free、high torque、high efficiency、stable, and low noise.
High-speed ball bearings, powerful magnetic outrunner rotor.
Suitable for T-REX 700E 、T-REX800E helicopters.

SPECIFICATIONS

• Input Voltage: DC11.1V-50.4V
• Max Continuous Current: 115A/250A(2sec)
• Max Output Power: 5100W/11000W(2sec)
• KV Value: 520KV
• Stator Arms: 12
• Magnet Poles: 10
• Shaft: 6x56.7x93.5mm
• Weight: 508g

The 250MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.

• Input voltage:2S~3S 2-3cell Li-Po
• Max continuous current:16/24A(5sec)
• Max output power:Approx. 170w/250W(5sec)
• KV value:3600KV
• Dimension:spindle 2.5xΦ25.5x22.4mm
• Weight:Approx. 33.5g

Align 470MX Brushless Motor(1800KV/2818)

Based on 6s voltage, the 470MX (1800KV) motor is tailor made for the T-Rex 470L DOMINATOR, featuring superior efficiency, high power output, extreme torque, and low current, low temperature.
As a totem to the 850MX Dominator motor, The 470MX shares the same extraordinary pedigree.
Even for the none 3D pilots, 470MX 6S motor utilizes less than 5 amps at hover. Not only does this require smaller C-rating packs, the lower temperature extends the battery life at the same time. Charging time basically is cut in half. These advantages makes this an ideal motor for just about everyone.
The 470MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.
The 470MX motor armature had a special balance adjust to improve the serious shaking problem that other tiny motors have.
Maintenance free, high torque, high efficiency, low temperature variant, stable and quiet.
Japanese made high-speed ball bearings, powerful magnetic outrunner rotor.
Suitable for T-REX 470L series,Must with 50A Brushless ESC(Governer Mode)(HES50X01).

Specification:

• Input voltage:6S
• Max continuous current:40A/60A(2sec)
• Max output power:Approx. 890w/1300W(2sec)
• KV value:1800KV
• Stator Dimension:2818
• Stator Arms:12
• Magnet Poles:8
• Dimension:spindle 3.5x36.4x51.7mm
• Weight:Approx. 120g

Accessories:

• Socket button head screw(M2.5X6mm) x 2
• Washer(F2.6XF5.8X0.6mm) x 2
• ALIGN standard 3mm gilt terminal x 3set

 

Align 460MX Brushless Motor 3200KV

1.Continuation of Align over 25 years motor core technical knowledge and craft, based on 3s voltage, the 460MX (1800KV) motor is tailor made for the T-Rex 450L DOMINATOR, featuring superior efficiency, high power output, extreme torque, and low current, low temperature. As a totem to the 850MX Dominator motor
2.As a totem to the 850MX Dominator motor, The 460MX shares the same extraordinary pedigree.
3.The 460MX motor incorporates radial fan in its end bell, creating powerful airflow to dissipate heat. Tweaks to motor design and reduction in weight not only contributes to dramatic power increase, the high efficiency cooling system enables cooler operating temperature during and after flights when compared to motor of previous generation.
4.The 460MX motor armature had a special balance adjust to improve the serious shaking problem that other tiny motors have.
5.Maintenance free, high torque, high efficiency, low temperature variant, stable and quiet.
6.Japanese made high-speed ball bearings, powerful magnetic outrunner rotor.
7.Suitable for T-REX 450E series.

Specification:

• Input voltage:3S
• Max continuous current:46A/68A(5sec)
• Max output power:Approx. 500w/730W(5sec)
• KV value:3200KV
• Dimension:spindle 3.5x29.2x38mm
• Weight:Approx. 87g

Accessories:

• Socket button head screw(M2.5X6mm) x 2
• Washer(Φ2.6XΦ5.8X0.6mm) x 2
• ALIGN standard 3mm gilt terminal x 3set

MC2834-1100kv is a high torque motor especially developed for the 450 CLASS  Multi-rotors platforms 

Note- for those who want to fly Acrobatic Quads, or Speed model: 6S configuration with  7-9" prop, you will get a LOT of speed, up to 140 km/h. we recommend it only for those who experienced in FPV or Quads flying.

Fits Spyder Little, F550, and many others.

The big advantage that it can be used with 8-10" props and with 4-6 S lipo, allowing you best flexible fit to multiple power combinations.

So what is so special in this motor:

1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

2- Heat, 25% lower heat generation thanks to ceramic bearings.

3- Japanese NMB bearings, highest resistance to vibrations.

4- 40cm cables, will allow direct connection to esc, wherever located.

Specifications:

•   No-load speed: 1100KV
•   Load current: 22 Amps
•   No load current: 0.8 Amps
•   Long cables (40cm)
•   Japan NMB bearings
•   Weight: 81gr
•   Motor Diameter :28.5 mm
•   Recommended Battery: 4-6S
•   Propellers to use: from 8-10"

  Included:

  MC2834 motor, 40cm wires
  Propeller mount with screws, Nut and Cup.

Example test data

Voltage (V)	Prop (inch)	Load current(A)	Power(W)	Thrust(G)	Efficiency (G/W)
11.1V	10*6	19,8	219,78	1000	4,55

 

Beam Brushless motor 4026-530KV, designed for most 550-600 models with up to 12s Lipos.Those motors are produced in Korea, make this product high quality motor.

Specifications:

• Motor KV - 530KV RPM/Volt
• Stator Arms - 12
• Magnet Poles - 10
• Motor Timing - 5deg
• Drive Frequency - 8kHz
• Input Voltage : 3-12s
• Max Continuous Current - 65A
• Max Continuous Power - 2850W
• Weight (g/oz) - 631g / 12.734oz
• Shaft size : 6mm

 

 

Solid aluminum construction.

Suitable for the Formula-1 and other medium-sized and large racing and recreational craft..
The shaft is adjustable tilt angle + 5 °, the height is about 12 mm. The electric motor is built using a water cooling.

Specifications

Length. 140 mm
Width . 65 mm
Height. 190 mm
Weight. 600 g

Description:

Lynx EOX brushless motors a new generation of high power, high efficiency helicopter motors.

Our new EOX motors will open your eyes to performance.

Developed by Lynx, these motors are perhaps the ultimate helicopter upgrade.

Featuring a single wire coil assembly for the best in efficiency, power and cool running.

High temperature rating Neodymium magnet and high quality material and component graduate EOX motor by Lynx a Limit Edition.

The EOX-2222 motor is the ultimate powerhouse for 450 class heli. The 6S-1970KV edition is designed to increase the Max Output Power and work with 6S.

The high quality of all components and material used, as the choice of a special single wire rewind system grade this motor as a Limited Edition

We introduce 3 Radial Bearign shaft supportand 100% Factory fine motor balancing for the ultimate motor consistency and vibe free.

Overall dimension was designed to fit in the standard frame without touch battery or servo.

EOX 2222 is sale with standard cable connector plugs.

So the next time you want to upgrade your helicopter – think Lynx EOX!

Technical Specifications:

• Motor Kv     1970KV
• Max Lipo Cell     6s  (22.2 MAX INPUT VOLT)
• Stator Diameter     22 mm
• Stator Length     22 mm
• No. of Stator Arms     9
• No. Magnet Poles     6
• Single Wire Diam.     0.40 mm
• Max Continuous Current     40A
• Max Continuous Power     870W
• Weight     81g - with wire and pin
• Outside Diameter     28 mm
• Body Length     30.3 mm
• Shaft Diameter     4mm - 3 Bearign Support
• Pinion Shaft Diameter     3,17 mm - With Lock Surface
• Overall Shaft Length     55 mm
• Motor Timing     5deg
• Drive Frequency     8kHz

Packing List:

• 1 x EOX 2222-6S-1970KV Motor with preinstalled conector plug
• 4 x Hex Cup Screw M3x5
• 4 x Hex Cup Screw M3x8

MC3536-380kv , made for 6S setups, and is a high torque motor especially developed for the Multi-rotors platforms .

This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

So what is so special in this motor:

1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

2- Heat, 25% lower heat generation thanks to ceramic bearings.

3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

Specifications:

•     No-load speed: 380kv
•     Load current: 19Amp
•     Burst Amps : 30 Amps
•     Power: 430 W
•     Short shaft
•     Propeller mount diameter: 6mm
•     Long cables (60cm)
•     3 x Ceramic Hybrid bearings
•     Weight: 104gr
•     Size : 35 x 36 mm
•     Poles: 14
•     Recommended Battery: 6S, 22.2V
•     Resistance 44 mOhm
•     Idle current @ 10v :0.7 Amps
•     Propellers to use: from 12" to 14"

    Included:

    MC3536-380KV motor
    Propeller mount with screws, Nut and Cup provided for choice.

See the movie showing Sky hero setting a speed record using the MC3536 motor

Multicopter Quadrotor 5010-14 360KV Brushless Motor

1.Machined aluminum front housing with four fan-style cooling holes that pump air through the motor while it runs.

2.Rear threaded mounting holes with both 16 mm and 19mm hole spacing fit a variety of applications.

3.Specially designed NdFeB magnets with high temperature rating for trouble-free operation.

4.High Temperature 140 C (356 F) rated wire is used for winding the motors to minimize the risk of burning up the motor.

5.High quality stator plates are epoxy coated on the inner surface to prevent winding shorts. 0.20mm stator plate id used .

6.High quality shielded and permanently lubricated ball bearings are used to support the motor shaft in all our motors.

7.High temperature adhesives are used to secure the stator windings and prevent them from shifting and getting pinched or shorting out .

• Model: D5010-14
• Motor size: 50*10mm
• Shaft size: 3.17mm
• Weight: 80g
• KV(rpm/v): 360
• Battery: 2-6Li-Po
• ESC: 10A
• Cable 40cm
• Best working with props of 14-16"

T-Motor U5 KV400 Motor U-Power Series: Stable, Durable, Powerful.

U-Power Technologies for AUW 8-12KG Multi-copter. Industrial grade, dust proof, water proof.

Unique Side Hole Design ensures swift airflow. Motor cools 2.5 times faster than others. Six holes beveling upward sparkles motor with waterproof and sand-resistant features.

Abnormal Shaft – a special screw is used for stator and rotor installation, avoiding loosiness of circlip.

High-Quality Varnished Wired – imported, oxygen-free copper coil which can tolerate temperature of 180C is employed to enhance short circuit resistance.

High-Standard Silicon Steel Sheet Precision Winding – the precision winding ensures the tightness of coil and slot. It helps reduce the copper lose while improving the utilization. Advanced 0.2mm silicon steel sheet reduces heat and eddy, thus improving efficiency.

Larger Bearing – Lower Noise: Adoption of imported German bearing prolongs the service life to over 1600 hours under trouble-free operation. German bearing enables motor run more smoothly and longer with lower noise.

Propeller Installation (Two Options, Patent Design) – Prop Installation and Traditional Installation.

Recommendation:

Voltage: 6S
Recommended prop: T-Motor CF15*5 / CF16*5.4 prop
AUW: Hexacopter, 9KG; Octocopter, 12KG.