MC3525-950KV is a high torque motor especially developed for the 450-500 CLASS Multi-rotors platforms THIS Motor is a tuning V2 version for the older motor 3525-930kv
Fits Spyder Little, F550, and many others.
As advantage that it can be used with 9-11" props and with 4-6 S lipo, allowing you best flexible fit to multiple power combinations.
So what is so special in this motor:
- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later
- Heat, 25% lower heat generation thanks to Japanese NMB bearings, resistant to vibrations.
Avizar MC4014 Brushless MultiRotor Motor 330kv, Specially made for Monster quads, for 6S setups.
Very high quality super smooth running motors, designed specifically for multirotor use. You can feel the difference just by turning them, and hear the difference on the run!
This motor has been custom designed in Europe, and tested during 2 years, and found to be the most efficient for most multi-copters from 700cm and up, due its features.
So what is so special in this motor:
1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later
2- Heat, 25% lower heat generation thanks to ceramic bearings.
3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.
4- Special size and low profile of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.
Features:
Sealed Japanese Ceramic Hybrid bearings
Short, hardened Japanese steel shaft
0.2mm NdFeB stator plates
Includes 6mm, prop adapter, and mounting plate
Oversized motor wires 3.3mm, silicone, for long and safe mounting.
Multirotors are used in many projects. because of High demands, longer flying times, heaver loads and Extreme climate conditions, there is a growing demand for Higher quality motors.
Delivering best demands, designed for Water proof and dust resistance, X3 motors give you more value.
X3 motor delivered in Black coating Matt finish, it fits 35mm motor mounts.
Delivered with original Japanese bearings, Dynamically balanced for Zero vibrations.
Fits 4-8S lipos, tested with props 12-14"( see table below)
Delivered with Standard shaft adapter for Conventional props and Flat adapter for Flat props.
Special design, XXL Aftermarket Inertic bottom plate for Spyder.
This inertic mount was created after research and opportunity to improve and ease of use for Mounting, allow easier adjustment CG of Sky hero Spyder
Made from 3.0mm Carbon reinforced FRP material, make this mount plate resistant to Shocks, and very rigid.
Wider : Allows mounting of 2x 6s 5000-6000 Lipos side by side without touching the screws.
Longer plate : 37 CM - allows perfect CG with or without gimbal, use with 1 or 2 lipo packs
Forward Side mounting holes: For easy gimbal mounting direct, or on tubes of Xaircraft type
Back Holes for GPS mounting, or FPV TX.
To use this plate in current Spyder you will need to make some 4mm holes in the bottom plate of Spyder.
Those motors produced OEM by strict requierments: Extra Low Vibrations, Balanced core and outside corps, Thicker Wire- are just part of the features those motors comes with.
They made especially for FPV/Multirotors products, however they can be used on other products as well. Benefit from Highest quality at the low price due the mass production.
Model: 2204-14 Motor size: Ф28*12mm Shaft size: Ф3.175mm Weight: 22g KV(rpm/v): 1400 Max Power: 97W Battery: 2-3Li-Po Test Prop: 6030/7040 Ri(M Ω): 0.270 ESC(A): 10A
3mm Thick Black Double Sided Foam Tape 20mm x 1 Meter.
Excellent vibrations absorber. Glue on gyros, FBL units, and more.
This is a strong, general purpose foam tape coated on both sides with an adhesive that will perform in both internal & external applications.
The foam is a high quality polyolefin coated with a high tack acrylic adhesive.
This tape has been designed as an economic solution for your adhesive foam tape requirements.
This HEXAcopter frame is the part of our new super professional range,which was developed over 2 years of research.
It`s made from extra strong patented technology carbon fiber plates and tubes, using our own technologies and equipment. It`s build to provide very smooth and stable flight with extra-heavy up 5kg payloads .
This frame is foldable - it`s very comfortable for transport . You`ll be need to release 12pcs of wingnuts to fold the motor arms and landing gears to put your copter into the storage place.
Two big li-po shelves allow the use of two-four LiPos to increase flying time and make their replacement easy and in correct CG.
The protection cage will keep the copter`s electronic equipment in cases of over flips, protecting expensive electronics.
Ultimate camera mount adaptor plate is specially designed to reduce vibration on camera . It`s compatible with all camera mounts .
The Frame made to mount Allstandard controllers as the ones necessary for the distribution board with the speed controllers.
This machine including a large foldable landing gear (350-500 mm of clearance).
The frame is delivered partially assembled, so building is faster and easier.
Diameter of the frame +- 1100mm.
Weight of the frame with landing gears, protection cage and camera mount adaptor plate – 1950 gr
This co-axial quad/octocopter frame is the part of our new super professional range,which was developed over 2 years of research.
It`s made from extra strong patented technology carbon fiber plates and tubes, using our own technologies and equipment. It`s build to provide very smooth and stable flight with extra-heavy up 5kg payloads .
This frame is foldable - it`s very comfortable for transport . You`ll be need to release 12pcs of wing nuts to fold the motor arms and landing gears to put your copter into the storage place.
Two big li-po shelves allow the use of two-four LiPos to increase flying time and make their replacement easy and in correct CG.
The protection cage will keep the copter`s electronic equipment in cases of overflips, protecting expensive electronics.
Ultimate camera mount adaptor plate is specialy designed to reduce vibration on camera . It`s compatible with all camera mounts .
The holes to mount standard controllers and also the MikroKopter electronics are already foreseen on the centerplate, as the ones necessary for the distribution board with the speed controllers.
This machine including a large foldable landing gear (350mm of clearance).
The frame is delivered partially assembled, so building is faster and easier.
Diameter of the frame +- 1100mm.
Weight of the frame with landing gears, protection cage and camera mount adaptor plate – 2011gr
This is a Bubbleless Fuel Pick-Up (clunk) Weight for Aircraft and Heli Fuel Tanks. The weight attaches to fuel tubing and is put into an aircraft's fuel tank.
FEATURES: Plated throughout to prevent corrosion Mesh design prevents bubbles from entering the fuel line and causing damage to the engine. Fuel fitting barb and weight are positively joined together to eliminate risk of coming apart Silicone-rubber O-ring prevents internal damage to fuel tank Used for glow fuel only.
INCLUDES: One Bubbleless Fuel Pick-Up Weight One Rubber O-Ring
Mounting Plastic Clamps, special size for servo cables, antennas, silicone Lines, and more.
Arrange your cabling nicely across the helicopter
Including a Pack of 10
Brushless Gimbal is a midi size, designed for Camcorder, and size of NEX5/7 compact SLR , similar or smaller cameras. It features zero noise, easy adjustment and nearly full range of camera compatibility.
Gimbals 100% produced in Europe, with locally re-winded BL-motors, and with Alex mos type controller.
This gimbal delivered PRE-installed, and as "ready to fly". must be tuned for device
Weight is 250 gr- VERY lightweight gimbal compared to rest of market.
Included:
Camera Gimbal
Gimbal Motors
Connection cables
To be completed: Alex Mos controller (Optional)
Please note the gimbal can be different from the image, we can optimise the gimbal per customer need, e.g to fit it 100% for camera,or camcorder.
Carbon Fiber 3k tube in Camouflage finish Size : 20 mm OD, 18mm ID, Length of 1 meter. Can be used as replacement for Boom, Sky hero tubes and more.
Specifications:
Size:20mm out diameter 18mm inner diameter
Length: 1000mm
100% Carbon Fiber
Quantity: 1pc
Shipping limitations( because of some shippers can not ship 1m long packages, we propose to cut the tubes- if possible!please advise +- the size how you want them cut, example 50/50cm, 30-70...
Protect your canopy edges, or use it as wire protection against carbon frames, use it combined with fuel tanks.. and much more.
this Strip including U shape EPDM. the profile is U shape and its 1.2mm wall thick, fits perfectly 1-2 mm frames.
See images for exact dimensions and sizes.