AVIZAR

AVIZAR

Producer of Motors, ESC, Accessories , all in High European quality.

Products


  • Micro Parallel Board - mCPX & nCPX

    Micro Parallel Board - mCPX & nCPX

    Micro Parallel Charging Board - Unlimited Flight at Your Fingertips. Safe Parallel Charge Board for mCPX & Pico

    One of the best ways to extend your day of flying is multiple batteries, and with this Micro Parallel Charging Board, you can now charge up to (6) Ultra Micro Batteries, and (6) Nano CPX style batteries, allowing you to take flight times to new limits.

    Compatible with UMX style batteries found in aircraft like the Blade mSR, and NCPX batteries found in aircraft like the Blade nCPX, this parallel board can charge up to (12) batteries at once, allowing you to spend more time flying, and far less time waiting for your batteries to charge. Further, this micro parallel board is protected by self resettable fuses to prevent shorts when charging batteries in parallel.

    Specifications

    • Input Charge Connector: Male 4mm Banana Plug
    • Output Connector: 6x 1S Female JST-PH; 6x Female Pico
    • Wire Type: 18 AWG Silicone Charge Lead
    • Max Charge Rating: 1.5A per battery
    • Fuse Rating: 1.5A
    • Wire Length: 8"


    When charging in parallel, it is best to be sure that the batteries being charged are close in overall voltage. Charging multiple batteries that are far out of balance with each other can limit the batteries potential and shorten battery life.

    SKU: PH2-UMXNCP
    €7.00
    inc. VAT

     IN STOCK
  • Micro switch for leds, Multicopters

    Micro switch for leds, Multicopters

    This is a micro switch, to be glued or soldered on small FPV racer. you can use it as a switch for Leds.

    Very small size, however not recommended to be used as main switch.

    Check drawing for details

    General size 6.6x2.7mm, thick is 1mm.  weight 0.1gr.

    SKU: Switch-sm
    €1.50
    inc. VAT

     IN STOCK
  • Mini Brushless gimbal for Gopro 2-3-4 models, 2 axis

    Mini Brushless gimbal for Gopro 2-3-4 models, 2 axis

    Mini Brushless Gimbal  for Gopro 2-3-4 models, 2 axis
    This gimbal is designed and produced in EU
    Very easy to mount with 2 plates, to be mounted in front as FPV or Photo gimbal.
    Controller not included.
    SKU: MINIGIMBAL
    €99.00
    inc. VAT

     LOW STOCK
  • Mini Camera Board-LED Board for FPV Racers

    Mini Camera Board-LED Board for FPV Racers

    Mini Camera Board-LED Board designed especially for FPV Racers, quadcopters

    • Specially designed for mini multirotors
    • Suitable for camera fixing and light DIY on mutirotor, airplane, helicopter, RC etc.
    • Board Only - Camera is not included

    Specifications:

    • Input voltage :3S LiPo Battery
    • Size: approx. 38.5 x 38.5mm
    • Net Weight: 5g
    • Quantity : 1 PC
    SKU: CAMBOARD
    €7.00
    inc. VAT

     IN STOCK
  • Motor Shaft for Avizar motor 28XX

    Motor Shaft for Avizar motor 28XX

    Motor Shaft for Avizar motors

    SKU: AVIZ2822
    €2.00
    inc. VAT

     IN STOCK
  • MT2206-2000KV Self-locking CW+CCW Multi-Rotor Motors

    MT2206-2000KV Self-locking CW+CCW Multi-Rotor Motors

    This is a set of Multicopter Motors, perfect for 250 size model FPV racers. Set including CW and CCW self locking adaptor motors.

    • The magnet  is 40 uh.
    • Long life Japanese NMB bearings
    • 0.20mm laminations, maximum efficiency and minimum losses.
    • Ultra-flexible motor leads with high-temp 220 °silicone rubber.
    • 2.0mm bullet connectors already installed.
    • With rotor dynamic balance process.
    • The prop adapters in CW/CCW rotation

    Specifications:

    • KV: 2000
    • Configuration: 12N14P
    • Stator Diameter: 22mm
    • Stator Length: 6mm
    • Shaft Diameter: 3.0mm, OD:2.0mm
    • Motor Dimensions(Dia.*Len): 28×18mm
    • Weight (g): 30g
    • No.of Cells(Lipo): 2-3S
    • Max Continuous current(A): 14.7A
    • Max Continuous Power(W): 163.2W
    • Internal resistance: 0.098Ω

    Package includes:

    1x 2206-2000KV CW motor
    1x 2206-2000KV CCW motor

    SKU: MT2206-2000
    €28.00
    inc. VAT

     IN STOCK
  • Multi All-in-One Balance Board TP Hyperion JST-XH EH

    Multi All-in-One Balance Board TP Hyperion JST-XH EH

    Description:

    Multi All-in-One Balance Board TP Hyperion JST-XH EH

    SKU: Q-B-0034
    €5.50
    inc. VAT

     LOW STOCK
  • Multi Function Motor Grip Plier

    Multi Function Motor Grip Plier

    Multi Function Motor Grip Plier  For RC Models

    Designed to grip the can of your electric motor without Scratching it.
    Silicon inserts help prevent scratching and allow you to get a better grip of your prop nut/spinner making removal of your propeller far easier.
    Can be used on any round object that needs gripping such as print heads on 3D printers, carbon fiber or aluminium tubes or even hold the handle of a driver to get more leverage.

     

    SKU: TOOL004
    €18.00
    inc. VAT

     IN STOCK
  • Multi harness cable 15cm for receiver and flybarless system or multicopters FC

    Multi harness cable 15cm for receiver and flybarless system or multicopters FC

    Multi harness cable 15cm for receiver and flybarless system or multicopters Flight controllers


    Package includes:

    • 1 multi harness cable lead 15cm.
    SKU: MU58139
    €4.90
    inc. VAT

     IN STOCK
  • Multi-Port Safe Parallel Adapter for EC5 XH/EH/HR

    Multi-Port Safe Parallel Adapter for EC5 XH/EH/HR

    Working with big 6S packs? Cut the clutter and get the one board that's designed specifically for your application.

    Designed from the ground-up with one purpose, this board is as straightforward as we could make it, with EC5 and 6S JST-XH connectors for up to four packs in parallel. With fuse protection on both the main and balance connections, you can rest easy knowing that all your gear is protected from any short circuits. 40A blade fuses on the main circuits are easily replaceable if needed, while the balance circuits have self-resetting poly-fuses built into the board.

    With both main and balance cables included to connect to whatever charger you're using, this is a true plug-and-play solution.

    SKU: MPL-EC5
    €55.00
    inc. VAT

     IN STOCK
  • Multi-Rotor Motor MC3510-360KV

    Multi-Rotor Motor MC3510-360KV

     MC3510 size motor especially developed for the Multi-rotors platforms. Fits props with 6mm hole and Flat props

    • Motor diameter: 42.5mm
    • Configuration : 12N14P
    • Length: 31.5mm
    • Stator Diameter:35mm
    • Shaft : m5
    • Weight: 97 Grm
    • Input voltage: 3-6S, 11-22V
    • No load current: 0.7A
    • Max load current: 25A
    • Internal resistance: 0.062 Ohm
    • Top mounting holes: 12/17mm, M3
    • Bottom mounting: 25/25, M3
    • Recommended esc: 30Amp

    Wire length : 50cm

    Delivered with prop adaptor 6mm and Flat prop adaptor

    SKU: MC3510-360KV
    €45.00
    inc. VAT

     IN STOCK
  • Multi-Rotor Motor MC3536-380KV 6S

    Multi-Rotor Motor MC3536-380KV 6S

    MC3536-380kv , made for 6S setups, and is a high torque motor especially developed for the Multi-rotors platforms .

    This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

    So what is so special in this motor:

    1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

    2- Heat, 25% lower heat generation thanks to ceramic bearings.

    3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

    4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

    5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

    Specifications:

    •     No-load speed: 380kv
    •     Load current: 19Amp
    •     Burst Amps : 30 Amps
    •     Power: 430 W
    •     Short shaft
    •     Propeller mount diameter: 6mm
    •     Long cables (60cm)
    •     3 x Ceramic Hybrid bearings
    •     Weight: 104gr
    •     Size : 35 x 36 mm
    •     Poles: 14
    •     Recommended Battery: 6S, 14.8V
    •     Resistance 44 mOhm
    •     Idle current @ 10v :0.7 Amps
    •     Propellers to use: from 12" to 14"

        Included:

        MC3536-380KV motor
        Propeller mount with screws, Nut and Cup provided for choice.


    See the movie showing Sky hero setting a speed record using the MC3536 motor

    SKU: MC3536-380KV
    €69.00
    inc. VAT

     IN STOCK
  • Multi-Rotor Motor MC3536-710KV

    Multi-Rotor Motor MC3536-710KV

    MC3536 is a high torque motor especially developed for the Multi-rotors platforms . made for 4-6S setups.

    This motor has been custom designed and tested during 2 years, and found to be the most efficient for most multi-copters from 500cm and up, due its features.

    So what is so special in this motor:

    1- Dynamic balance, very few motors are really dynamically balanced. the equipment is very unique, and we do insist on the fact and also costs involved that the motor should be balanced, otherwise the fatal vibration will kill the machine sooner or later

    2- Heat, 25% lower heat generation thanks to ceramic bearings.

    3- Ceramic hybrid bearings, and the motor has 3 of them: Radial forces of motor taken away with the help of those special bearings, which also self lubricated,the smoothness of the motor felt directly with the throttle reaction.

    4- 60cm cables, will allow direct connection to most size frames, up to 1.2 meters.

    5- Special size of cage and motor shaft will allow perfect setup and perfect performance on any setup, single or coaxial.

    Specifications:
     

    •   No-load speed: 710kv
    •   Load current: 23Amp
    •   Burst Amps : 32 Amps
    •   Power: 340 W
    •   Short shaft
    •   Propeller mount diameter: 6mm
    •   Long cables (60cm)
    •   3 x Ceramic Hybrid bearings
    •   Weight: 104gr
    •   Size : 35 x 36 mm
    •   Poles: 14
    •   Recommended Battery: 4S, 6S for Speedy machines!
    •   Resistance 44 mOhm
    •   Idle current @ 10v :1.7 Amps
    •   Propellers to use: from 11" to 13"


      Included:

      MC3536-710KV motor
      Propeller mount with screws, Nut and Cup provided for choice.

     

     

     

     

    Movie shows the Sky hero setting a record using this motor

    SKU: MC3536-710KV
    €69.00
    inc. VAT

     IN STOCK
  • Multi-Rotor Motor MC4008-390KV

    Multi-Rotor Motor MC4008-390KV

     MC4008 size motor especially developed for the Multi-rotors platforms. Fits props with 6mm hole and Flat props

    • Motor diameter: 46mm
    • Configuration : 24N22P
    • Length: 27.5mm
    • Stator Diameter:40mm
    • Shaft : m5
    • Weight: 95Grm
    • Input voltage: 14.8-29.6V
    • No load current: 0.8A
    • Max load current: 22A
    • Internal resistance: 0.055 Ohm
    • Top mounting holes: 12/17mm, M3
    • Bottom mounting: 25/25, M3
    • Recommended esc: 30Amp

    Wire length : 50cm

    Delivered with prop adaptor 6mm and Flat prop adaptors

    SKU: MC4008-390KV
    €49.00
    inc. VAT

     IN STOCK
  • Multicopter 5010-360KV

    Multicopter 5010-360KV

    Multicopter Quadrotor 5010-14 360KV Brushless Motor

    1.Machined aluminum front housing with four fan-style cooling holes that pump air through the motor while it runs.

    2.Rear threaded mounting holes with both 16 mm and 19mm hole spacing fit a variety of applications.

    3.Specially designed NdFeB magnets with high temperature rating for trouble-free operation.

    4.High Temperature 140 C (356 F) rated wire is used for winding the motors to minimize the risk of burning up the motor.

    5.High quality stator plates are epoxy coated on the inner surface to prevent winding shorts. 0.20mm stator plate id used .

    6.High quality shielded and permanently lubricated ball bearings are used to support the motor shaft in all our motors.

    7.High temperature adhesives are used to secure the stator windings and prevent them from shifting and getting pinched or shorting out .

    • Model: D5010-14
    • Motor size: 50*10mm
    • Shaft size: 3.17mm
    • Weight: 80g
    • KV(rpm/v): 360
    • Battery: 2-6Li-Po
    • ESC: 10A
    • Cable 40cm
    • Best working with props of 14-16"

    SKU: BC5010/14-360KV
    €46.00
    inc. VAT

     IN STOCK
  • Multicopter 85A Brushless Speed Controller ESC

    Multicopter 85A Brushless Speed Controller ESC

     85A Programmable Brushless Speed Controller ESC

    Specifications

    85A ESC
    Output: Continuous 85A, Burst 100A up to 10 Secs.
    Input Voltage: 2-6S Lipo
    sBEC: 4A/5.5V

    Dimensions W*L*H:33 x 60x 17(mm)
    Weight: 60g

    SKU: XH85ASBEC
    €39.00
    inc. VAT

     IN STOCK
  • Multicopter APC MR type 9x4.5 Carbon/Nylon Props

    Multicopter APC MR type 9x4.5 Carbon/Nylon Props

    These are all new props on the market. They are built to a higher standard than the normal prop manufactures and will require little to no balancing.

    Set of 4 props 9x4.5, 2cw+2ccw

    2 sets of Adaptor Rings.

    SKU: HQ945SET
    €10.00
    inc. VAT

     LOW STOCK
  • Multicopter CARBON Propeller set 12X4.5 L/R

    Multicopter CARBON Propeller set 12X4.5 L/R

     1 Pairs 12X4.5 Carbon Fiber Propellers CW/CCW for multicopter

    Specifications:

    • Material:Japan made carbon fiber
    • Epoxy resin cover
    • Size:12X4.5 cw, 12x4.5ccw
    • High gloss 3K finish
    • Very strong and light weight
    Included : Pair: 1 CW, 1 CCW
    SKU: CFMP1245
    €19.50
    inc. VAT

     IN STOCK
  • Multicopter CARBON Propeller set 13X4 L/R

    Multicopter CARBON Propeller set 13X4 L/R

    1 Pair of 13x4 Carbon Fiber Propellers CW/CCW for multicopter

    Specifications:

      Material:Japan made carbon fiber
      Epoxy resin cover
      Size:13x4 cw, 13x4ccw
      High gloss 3K finish
      Very strong and light weight

    Included : Pair: 1 CW, 1 CCW

    SKU: CFMP1340
    €21.00
    inc. VAT

     LOW STOCK
  • Multicopter CARBON Propeller set 14X4.7 L/R

    Multicopter CARBON Propeller set 14X4.7 L/R

    1 Pair of 14x4.7 Carbon Fiber Propellers CW/CCW for multicopter

    Specifications:

      Material:Japan made carbon fiber
      Epoxy resin cover
      Size:14x4.7 cw, 14x4.7ccw
      Hole 6mm
      High gloss 3K finish
      Very strong and light weight

    Included : Pair: 1 CW, 1 CCW

    SKU: CFMP1447
    €22.00
    inc. VAT

     IN STOCK
  • Multicopter CARBON Propeller set 15X4 L/R

    Multicopter CARBON Propeller set 15X4 L/R

    1 Pair of 15X4 Carbon Fiber Propellers CW/CCW for multicopter

    Specifications:

      Material:Japan made carbon fiber
      Epoxy resin cover
      Size:15X4 cw, 15X4ccw
      High gloss 3K finish
      Very strong and light weight

    Included : Pair: 1 CW, 1 CCW

    SKU: CFMP1540
    €25.00
    inc. VAT

     IN STOCK
  • Multicopter CARBON Propeller set 16X5 L/R

    Multicopter CARBON Propeller set 16X5 L/R

    1 Pair of 16X5 Carbon Fiber Propellers CW/CCW for multicopter

    Specifications:

      Material:Japan made carbon fiber
      Epoxy resin cover
      Size:16X5 cw, 16X5ccw
      High gloss 3K finish
      Very strong and light weight

    Included : Pair: 1 CW, 1 CCW

    SKU: CFMP1650
    €29.00
    inc. VAT

     IN STOCK
  • Multicopter Collapsible GPS Antenna stand Mount

    Multicopter Collapsible GPS Antenna stand Mount

     Multicopter Collapsible GPS Antenna Mount

    •   Collapsible design
    •   Full set include GPS antenna mount, 4mm carbon fiber stick and base.
    •   Material: Aluminum
    •   High: 160mm
    •   Weight 19g
    SKU: 64012131
    €13.00
    inc. VAT

     IN STOCK
  • Multicopter led Light 50mm Yellow

    Multicopter led Light 50mm Yellow

    Multicopter led Light 50mm, available in yellow
    , size is 50mm long, 12m wide.
    This light has 4 strong SMD led chips, gives you perfect visibility in day time, or during the race. Operating voltage- 5V DC

    SKU: LED50
    €5.50
    inc. VAT

     LOW STOCK

Manufacturers