AlignRc

AlignRc

producer of famous T-Rex helicopters

Products


  • G800 Aerial Gimbal System

    G800 Aerial Gimbal System

    Align G800 gimbal is an upgrade product catered specifically for the needs of aerial photography. The included GS800 gimbal controller features high power computing capability, and various control modes to precisely lock into the shooting object, as well as meet the needs of various other aerial photography needs, allowing optimal imagery to be obtained easily.

    This system recommended to be used in conjunction with Align's APS, 3GX and T-Rex 800E. 3k carbon composite material matched with high strength aluminum alloy to form the gimbal backbone, featuring high precision, high stability, capable of high payload, and is able to sustain hard landing of helicopter. When paired with 540 degrees DS815 servo and belt transmission design, the gimbal is capable of wider turning angles with higher precision.

    • Unique gimbal support assembly design, with aesthetic pleasing clean look, featuring high precision and slop free and makes the camera lens maintain at the same angle in flight.
    • Shock absorbing dampners designed specifically for Align GS800 gimbal system, posses superior vibration dampening effect, and various spring tensions can be used according to payload.
    • Gimbal features 3k carbon composite material matched with high strength aluminum alloy to form the backbone, featuring high precision, high stability, high payload capability, and is able to sustain hard landing of helicopter. 
    • Utilizes 540 degrees DS815 high voltage robotic servos, supporting 2s 7.4v input voltage. Special slow start feature to avoid jerky start-ups.
    • Unique gimbal support assembly design, with aesthetic pleasing clean look, featuring high precision and slop free and makes the camera lens maintain at the same angle in flight.
    • Shock absorbing dampners designed specifically for Align GS800 gimbal system, posses superior vibration dampening effect, and various spring tensions can be used according to payload.
    • GS800 gimbal controller is a highly stable, highly precise 3-axis gimbal control system. Featuring 5 control modes: mode 1 -three axis auto compensation; mode 2 - two axis auto compensation; mode 3 -three axis return to neutral; mode 4 - manual; mode 5 - rescue mode. These various modes will meet the variety needs of aerial photography.
    • Simple to setup. Complete setup can be done with two steps.
    • Unique rescue mode, to minimize photography equipment damage during a crash.
    • Supports lens zoom in and zoom out feature.
    • Supports shutter activation. Follow the instruction to connect shutter with GS800 controller, shutter can be activated via transmitter stick through GS800.
    • Supports Spektrum/JR satellite receivers and Futaba S.BUS architecture.
    • Upgradeable firmwareinterface, allowing firmware updates through interface cable.
    • Must be used in conjunction with Align APS gyro and 3GX flybarless system, enabling gimbal control system to achieve high stability and excellent controllability.
    • Users must have a certain concept of security to operate the R/C helicopters. 
    • Be sure to read and comply with related safety notes of instruction manual before flying.
    Specification :
    • Characteris Tic: Soft Start
    • Rating Voltage:DC4.8~7.4V
    • Temperature Range:-20℃~60℃(-20°~140℉)
    • Operating Range:540°(1000~2000us)
    • Broadband Systems:1500μs
    • Stall Torque:15kg.cm(4.8V)
    • 18kg.cm(6V)
    • 20kg.cm(7.4V)
    • Motion Speed:0.15sec/60°(4.8V)
    • 0. 13sec/60°(6V)
    • 0.11sec/60°(7.4V)
    • Dimension:40.1x20.1x20.7mm
    • Weight:66g
    Specification(GS800 CONTROLLER) :
    • Rating Voltage:DC4.8~8.4V
    • Temperature Range:-20℃~60℃(-20°~140℉)
    • Operating Current Consumption:
    • 55mA@ 6V(ROLL)
    • 40mA@ 6V(PAN)
    • Maximum Control range:
    • (ROLL) ±30°
    • (PAN) ±90°
    • (TILT) ±90°
    • Maximum Control rotation Speed:
    • (ROLL) 60°/ s
    • (PAN) 150°/ s
    • (TILT) 150°/ s
    • Dimension:42.7x 30 x 14.2mm
    • Weight:11g
    Accessories:
    • G800 GIMBAL x 1 set
    • Gimbal accessories x 1 set
    • Gimbal Support Assembly x 1 set
    • Gimbal Shock Absorbers Assembly x 1 set
    • Gimbal shock absorber accessories x 1 set
    • Gimbal camera pad x 2 pcs
    • ESC mount x 1 pcs
    • DS815 HV Robor Srevo x 3 set
    • GS800 Controller x 1 set

     

    SKU: H80B001X
    €899.00 €1599.00
    inc. VAT

     72HR STOCK
  • GP900 Head Lock Gyro

    GP900 Head Lock Gyro

    Features: A new generation, multi-purpose gyroscope is born! The Align GP900 is the most feature rich, highest performance gyro on the market. In addition to supporting Spektrum/JR satellites so traditional receivers can be omitted, it is also compatible with Futaba’s S-BUS system. A throttle governor for gas/glow helicopters is built in, plus PC interface for custom parameter tweaking and firmware updates. A high processing cycle CPU is used to achieve more precise rudder compensation calculations quickly, providing the optimal rudder control for the modern high powered helicopters. Rudder pirouetting optimization allows for consistent pirouettes no matter what maneuver or speed. The multi-purpose Align GP900 is the ideal gyro system for flybar helis as well as F3C contestants. Upgrade now and experience the dramatic difference this gyro provides! Instruction: 1.Utilizes MEMS(Micro Electro Mechanical Systems) micro electronic sensors which are small, highly reliable, and highly stable. 2.16bit high processing speed CPU is used for ultra high resolution, resulting in higher rudder precision than previously possible, even on modern high powered helicopters. 3.Supports Spektrum and JR satellites, traditional receiver not needed. 4.Support Futabs S-BUS system. 5.Support both digital and analog servos. 6.Support both wide and narrow band receivers. 7.Integrated RCE-G600 speed governor function, thus GP900 can provide speed governor function without additional electronics. 8.Suitable for all 200 to 700 size glow engine or electric helicopters, with higher vibration resistance than any other systems. Superior performance is achievable even with harder mounting foam tapes. 9.Support parameter setting through PC interface, as well as firmware updates. 10.Anti-torque compensation. Optimal tail locking achievable no matter if gyro is mounted upright or inverted. Specification: Operating Voltage:DC 3.5~8.4V Current Consumption:<80mA @ 4.8V Angular Detection Speed:600 degrees/sec Operating Humidity:-20℃~65℃ RoHS certification. Operating Humidity:0%~95% Size:36.5x25.2x15.6mm Weight:11g
    SKU: HEG90001
    €99.90
    inc. VAT

     72HR STOCK
  • Gpro Flybarless System

    Gpro Flybarless System

    New multifunctional Gpro flybarless system with active CPU, processing 20 times faster than previous generation. The freshly new software structure improves system compensation, bring GPro up with precise and agile response, and also keep up-to-date flying performance than ever.The most important is that utilizes with latest iOS and Android APP can be easily and directly adjusted through mobile phone while at the field. New human oriented interface allows convenient and rapid setup and installation.

    Brand new CPU, processing 20 times faster than previous generation, bring GPro up with precise and agile response.
    Freshly new software process structure improves system compensation and keep up-to-date flying performance.
    Utilizes with latest iOS and Android APP that GPro can be easily and directly adjusted through mobile phone while flying outdoors.
    New human oriented interface allows convenient and rapid setup and installation.
    Superior flying characteristic remain the same flying control among T-REX 250-800 helicopters.
    Full support receivers and satellites currently on the market, including S.BUS/X.BUS and DSM2/DSMX/DSMJ/DMSS.

    Specifications:

    • Operating voltage range:DC 3.5V-8.4V.
    • Operating current consumption:<100mA  4.8V.
    • X and Y axis Operating Angle Range:-300/+300 degree
    • Z axis Operating Angle Range:-600/+600 degree
    • Sensor resolution: 12bit
    • Supports 90/120/135/140 CCPM swashplates
    • Spektrum and JR Satellite antennas support (Replaces original factory receiver)
    • Futaba S.BUS/JR X.BUS system support
    • Rudder support 760 narrow band servos
    • Supports multi-blade rotor heads
    • Engine speed governor range:10500-21000 RPM
    • Operating Temperature:-20/65 degree
    • Operating Humidity:0%95%
    • RoHs cerification stamp
    • Size:36.5x25.2x15.6 mm
    • Weight:11.5g

    Includes:

    • USB Link cable set x 1
    • Signal wire x 3
    • Gpro Sticker x 1
    • Gpro Double Sided Tape x 2
    SKU: HEGPRO01
    €199.90
    inc. VAT

     72HR STOCK
  • H Servo Horn Set

    H Servo Horn Set

    Use for Hitec Servo

    ●Quantity: 3 pcs

    SKU: HN6049
    €3.90
    inc. VAT

     LOW STOCK
  • H50G004XX Motor Slant Thread Pinion Gear 12T T-REX 500L

    H50G004XX Motor Slant Thread Pinion Gear 12T T-REX 500L

    Use for T-REX 500L.
    Highly enhance structural strength, effectively increase the torsional capability.
    Motor Slant Thread pinion gear 12T x 1
    M4 set screw x 2(M3x3mm)

    SKU: H50G004
    €7.80
    inc. VAT

     72HR STOCK
  • H70H012XXT

    H70H012XXT

    Use for 700 / 760 / 800 with Three-Blade Rotorhead

    Content

    • 6x 700E Tri-Blades Head Damper
    SKU: SKU54486
    €6.90
    inc. VAT

     72HR STOCK
  • Hardware Bag

    Hardware Bag

    Use for T-REX 250.

    Specification:

    Hexagonal screw hole 1.3mm
    Socket screw x 2(M2x5mm)
    Stainless steel socket screw x 2(M2x8mm)
    Socket button head screw x 23(0#x3mm)
    Socket button head screw x 13(0#x4mm)
    Socket button head screw x 9(0#x5mm)
    Socket button head screw x 3(0#x6mm)
    Socket button head screw x 4(0#x8mm)
    Socket button head screw x 2(0#x10mm)
    M2 set screw x 4(M2x2mm)
    M2 set screw x 2(M2x6mm)
    Socket button head collar screw x 2(0#x4mm)
    Socket button head self tapping screw x 16(T1.5x3mm)
    Socket button head self tapping screw x 2(T1.5x4mm)
    Socket button head self tapping screw x 4(T1.5x5mm)
    Socket button head self tapping screw x 6(T1.5x6mm)
    Countersunk philips self tapping screw x 3(T1.5x4mm)
    Screw x 1(M1.2x3mm)
    M1.5 special washer(Φ1.5xΦ2.7xΦ3.6x1.2mm) x 34

    SKU: H25033A
    €10.00
    inc. VAT

     72HR STOCK
  • Hardware Bag

    Hardware Bag

    Specification:

    ●Self tapping screw x 4(T1.4x7mm)

    ●Self tapping screw x 2(T2x6mm)

    ●Self tapping screw x 6(T2x8mm)

    ●Self tapping screw x 2(T2x10mm)

    ●Self tapping screw x 1(T2x16mm)

    ●Collar screw x 2(M2x8mm)

    ●Collar screw x 1(M2x9mm)

    ●Collar screw x 1(M2x12mm)

    ●Collar screw x 2(Φ4.5x7mm)

    ●Socket screw x 1(M2x12mm)

    ●Set screw x 2(M3x3mm)

    ●M2 nut x 1

    ●Washer x 4(Φ2xΦ3.6x0.2mm)

    ●Washer screw x 6(T2x5mm)

    ●Collar x 1(Φ3x2.15mm)

    ●Lever collar x 1(Φ3xΦ2x3mm)

    ●Ball link(long) x 2

    ●Ball link(short) x 1

    ●Linkage rod(A) x 1(Φ1.3x9mm)

    ●Linkage rod(B) x 1(Φ1.3x12.5mm)

    ●Linkage ball A (M2x2.5mm)x 2(Φ4.75x7.18mm)

    ●Main shaft lock ring x 1

    ●Aluminum collar x 2(Φ5xΦ3x1.5mm)

    ●O-ring x 2(Φ3xΦ6.5x2mm)

    ●Socket screw x 1(M2x5mm)

    ●Collar screw x 1(M2x5)

    ●Socket screw x 1(M2x12mm)

    SKU: HZ027
    €4.90
    inc. VAT

     LOW STOCK
  • Head Linkage Ball Assembly

    Head Linkage Ball Assembly

    Use for T-REX 600E PRO
    Steel ball parts is made of rigid stainless steel, features wear-resisting, and anti-oxidization. Therefore this refitting component is absolutely helpful for the accuracy of flying movement control and the stable of the flight.

    Specification:

    Linkage ball C(M3x3) x 4(Φ4.75x8.5mm)
    Linkage ball B(M3x3) x 5(Φ4.75x9.77mm)
    Linkage ball C(M3x3) x 4(Φ4.75x11.76mm)

    SKU: H60224
    €10.00
    inc. VAT

     LOW STOCK
  • Helicopter T-REX 760X 3D DOMINATOR TOP Combo

    Helicopter T-REX 760X 3D DOMINATOR TOP Combo

    T-REX 760X 3D DOMINATOR TOP Combo Align RC Helicopter

    The new models include all the current design updates from their previous releases that brings the whole T-REX family together.

    • New 700EFL Rotor Head, Super low CG
    • New 760 Main Blades & 105 Tri-Tail Blades
    • Narrow Body Design / Split-type of Main Frame
    • DS820M/DS825M High Voltage Brushless Servo
    • Powerful 850MX 490KV Motor
    • Brand New Platinum HV 160A V4 ESC

    Specifications

    • Length: 1390mm
    • Height: 360mm
    • Width: 195mm
    • Main Blade Length: 760mm
    • Main Rotor Diameter: 1702mm
    • Tail Rotor Diameter: 287mm
    • Motor Drive Gear: 12T
    • Main Drive Gear: 112T
    • Autorotation Tail Drive Gear: 102T
    • Tail Drive Gear: 23T
    • Drive Gear Ratio: 9.33:1:4.43
    • Weight (w/o Battery): Approx. 3750g

    Package Includes

    • 1x T-REX 760X 3D Dominator Kit
    • 2x 760 Carbon Fiber Blade
    • 2x 105mm 3K Carbon Fiber Tail Blade
    • 1x 850MX Brushless Motor (490KV)
    • 3x DS820M HV Brushless Servo
    • 1x DS825M HV Brushless Servo
    • 1x Platinum HV 160A V4 Brushless ESC

    Required for Assembly (NOT INCLUDED !)

    • 1x Transmitter (7-channel or more, helicopter system)
    • 1x Receiver (7-channel or more)
    • 2x 6S Li-Po 4500 ~ 5200mAh
    • 1x Digital Pitch Gauge
    • 1x Flybarless System

    Click here to see our Lipo Batteries

    Click here to see our Transmitters and Receivers

    SKU: RH76E01X-C
    €1899.99
    inc. VAT

     72HR STOCK
  • Hexagon Screw Driver 1.3mm

    Hexagon Screw Driver 1.3mm

    Super hard screwdriver head mady by HSS high alloy steel,wear and distortion resisting!

    Purifier handle made by aluminum alloy CNC.
    Specification:1.3mm Hexagon screw driver x1
    Weight:14.7g

    SKU: HOT00007
    €6.00
    inc. VAT

     72HR STOCK
  • Hexagon Screw Driver Set

    Hexagon Screw Driver Set

     
    Super hard screwdriver head made by HSS high alloy steel,wear and distortion resisting!

    Purifier handle made by aluminum alloy CNC , inside can place components and screws!

    Using on heli's M2 socket screw and M3 socket screw!
     

    SKU: HZ024
    €22.00
    inc. VAT

     LOW STOCK
  • High Carbon Steel Main Shaft- REPLACED BY H45022

    High Carbon Steel Main Shaft- REPLACED BY H45022

    High Carbon Steel Main Shaft- REPLACED BY H45022

    SKU: HS1217
    €11.00
    inc. VAT

  • High Strength Engine Fan

    High Strength Engine Fan

    ●Features high strength and straight rotation.
    ●Use for T-REX 600N / 600NP.

    SKU: HN6072
    €8.00
    inc. VAT

     LOW STOCK
  • HN7063 Align Main Blade Linkage Rod- Trex700N

    HN7063 Align Main Blade Linkage Rod- Trex700N

    Linkage rod(A) x 2(1.96x14mm)
    Linkage rod(B) x 2(1.96x22mm)
    Linkage rod(C) x 2(1.96x56mm)
    Linkage rod(D) x 2(1.96x44mm)
    SKU: HN7063
    €6.50
    inc. VAT

     LOW STOCK
  • Hook & Loop Fastening Tape

    Hook & Loop Fastening Tape

    Hook & Loop fastening tape x 2

    SKU: H60054
    €4.80
    inc. VAT

     72HR STOCK
  • HS1003 Feathering Shaft

    HS1003 Feathering Shaft

    Feathering Shaft x4

    SKU: HS1003
    €5.90 €5.95
    inc. VAT

  • HS1014 Landing Skid Set

    HS1014 Landing Skid Set

    Landing Skid Set :Landing skid x 2Skid pipe x 2 (Aluminum)Skid pipe end cap x 4Self tapping screw x 4 (M2 x 6)

    SKU: HS1014
    €9.00
    inc. VAT

     72HR STOCK
  • HS1028T Bearings (685ZZ) 5x11x5mm (4 pcs)

    HS1028T Bearings (685ZZ) 5x11x5mm (4 pcs)

    Bearings (685ZZ) 5x11x5mm (4 pcs)

    SKU: HS1028T
    €4.50 €4.95
    inc. VAT

     IN STOCK
  • HS1029T Bearings(693ZZ)

    HS1029T Bearings(693ZZ)

    Bearings(693ZZ)

    SKU: HS1029T
    €4.50 €4.95
    inc. VAT

     72HR STOCK
  • HS1030T Bearings(MR63ZZ) 4pcs

    HS1030T Bearings(MR63ZZ) 4pcs

    Bearing MR63ZZ x 4pcs (3x6x2.5mm)
    SKU: HS1030T
    €5.00
    inc. VAT

     LOW STOCK
  • HS1031T Bearings (3x8x3mm) x 4pcs

    HS1031T Bearings (3x8x3mm) x 4pcs

    Bearings (3x8x3mm) x 4 pcs

    SKU: HS1031T
    €4.50 €4.95
    inc. VAT

     IN STOCK
  • HS1032T Bearings(MR84ZZ) 

    HS1032T Bearings(MR84ZZ) 

    Bearings(MR84ZZ)

    Bearing MR84ZZ x 4 (Φ4xΦ8x3mm)

    SKU: HS1032T
    €4.50 €4.95
    inc. VAT

     IN STOCK
  • HS1033T Bearing  (MR52ZZ) 

    HS1033T Bearing (MR52ZZ) 

    Bearing (MR52ZZ)

    SKU: HS1033T
    €4.50 €4.95
    inc. VAT

     72HR STOCK

Manufacturers