Radiomaster

ExpressLRS ELRS ES900TX Ultra Long Range Transmitter Module and ES900RX 0.6g Receiver

ExpressLRS ELRS ES900TX Ultra Long Range Transmitter Module and ES900RX 0.6g Receiver

Please consult Local Telecom regulations when using this item!

ES900TX and ES900RX modules are a set of Long Range 915MHz/868MHz(optional) wireless transmission equipment developed and designed based on the open source software ExpressLRS. This set of modules is characterized by an ultra-long range, stable operation and low latency. The module is compatible with most Opentx remote controls,, basically plug and play. We specially adapted a heat sink for the transmitter module and also reserved the installation position of the 2006 fan, which can help the transmitter module work stably under high power conditions.

New ES900TX module comes with a 2006 fan, it works automatically when the TX power is 250mW.

Specifications:

ES900TX:

MCU: ESP32+ESP8285

Dimension: 55mm*39mm*11mm

Weight: 9.2 grams (TX module only)

Antenna connector: SMA

VCC input: 5~13v, Recommended 5v~9v

RF frequency optional: 915 MHz or 868 MHz (EU)

Maximum output power: <33dBm (For >27dBm operation we recommend adding a fan for forced cooling)

ES900RX:

MCU: ESP8285

VCC input: 5v

Current operation: ~100Ma

Rx to FC protocol: CRSF

RF frequency optional: 915 MHz or 868 MHz (EU)

Dimension: 12mm*12mm*3mm

Weight: 0.60 grams (excluding antenna)

Antenna connector: IPEX1

Telemetry output power: <17dBm

Download RC7 Firmware for ES900RX:

ExpressLRS RC7 firmware for ES900 RX 915MHz and 868MHz [update via WiFi]

INCLUDED

       1x ES900 TX module 868MHz OR 915

  • 1x TX antenna 868MHz/915
  • 1x Molding JR Bay mounted case for TX module
  • 1x Heat sink
  • 1x Adapter wire
  • ES900 RX module x1(868MHz or 915MHz optional)
  • RX antenna x2

€59.90

Inc. VAT
Quantity
RadioMaster - Ranger 2.4GHz ELRS Module LONG RANGE system

RadioMaster - Ranger 2.4GHz ELRS Module LONG RANGE system

Featuring an OLED display, a directional menu key, and two assignable shortcut keys the Ranger can be adjusted on the fly and personalized to your needs.

  • The Ranger includes a T Antenna for general use and a RadioMaster Moxon antenna for long-range directional applications. A micro module and nano module adapter are included to ensure the Ranger is compatible with most radios on the market today. A cable has also been included for use with Futaba radios that are CRSF capable.
  • Built-in Accelerometer;Packet rates up to F-1000Hz
  • Up to 1 Watt Power output;Wifi and Bluetooth support;High-efficiency cooling system

Features

  • OLED Display
  • Rugged CNC Case
  • Built-in Accelerometer
  • Packet rates up to F-1000Hz
  • Wifi and Bluetooth support
  • High-efficiency cooling system
  • 5 Direction Nav key and customizable shortcut buttons
  • Micro and Nano adapters included
  • Moxon and T-antenna included
  • CRSF cable for compatible Futaba radios included

    Specification
  • Item: Ranger 2.4GHz ELRS Module
  • Regulatory Domain: ISM2400
  • MCU: ESP32(main), ESP8285(aux, as ESP backpack)
  • RF chip: SX1281IMLTRT
  • Frequency Range: 2400 MHz - 2480 MHz
  • Maximum packet rate: 500Hz/F-1000Hz (F-1000Hz mode requires EgdeTX 2.7.1 or later)
  • Minimum receiver refresh rate: 25Hz
  • RF Output Power: Default 100mW
  • Module bay adapters: JR standard 5pin socket & Nano standard 8pin socket
  • Futaba CRSF socket cable: Included
  • OLED screen: 64x128px
  • Wifi Support: Yes
  • Bluetooth support: Yes
  • 3-Axis Accelerometer: Yes (STK8BA58 MEMS Accelerometer)
  • Built-in RGB light strip
  • XT30 Power supply voltage: DC 6V - 16.8V
  • Weight: 138g (with Moxon antenna) / 135g (with T antenna) / 126g (without antenna)
  • Dimension: 95*51*25mm (without antenna)

Please check local regulations for rules and permissions

Package including:

  • 1 * RANGER Module
  • 1 * Futaba CRSF socket cable
  • 1 * JR Adapter
  • 1 * Nano Adapter
  • 1 * T Antenna
  • 1 * Moxon Antenna
  • 1 * Hexagon socket screwdriver
  • 3 * M2*5 Screws
  • 1 * Assembly Manual

€109.00

Inc. VAT
Quantity
RadioMaster - RP1 2.4ghz ExpressLRS ELRS Nano Receiver V2

RadioMaster - RP1 2.4ghz ExpressLRS ELRS Nano Receiver V2

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today pilots have come to expect.

Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built in FW updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.
Tiny in size yet big on features and range the RP series of receivers have you covered.

What’s new on the RP1

Improved PCB design is better for heat dissipation.
Rigid antenna with greater durability and performance.
Solder pads are improved and easier to solder to.
LED on top side of PCB.

Specifications:

  • Item Name: RP1 Nano Receiver- LBT EU protocol
  • Type: ISM
  • ESP8285 MCU
  • SX1280IMLTRT RF Module
  • Antenna: 65mm 2.4ghz T Antenna
  • Frequency Range: 2400 MHz to 2480 MHz
  • Maximum receive refresh rate: 500Hz / F1000Hz
  • Minimum receiver refresh rate: 25Hz
  • Working voltage: 5v
  • Weight: 0.53g (without antenna)
  • Dimension: 13mm*11mm*3mm
  • TCXO: Yes

€24.00

Inc. VAT
Quantity
RadioMaster - TX16s Empty Module - Project box

RadioMaster - TX16s Empty Module - Project box

RadioMaster - TX16s Empty Module - Project box THIS box is made to add DIY module and Antenna. its an Optional part for Radiomaster TX16S

€3.99

Inc. VAT
Quantity
RadioMaster 5000mah 2s Li-ion TX-RX  Battery pack for TX16s

RadioMaster 5000mah 2s Li-ion TX-RX Battery pack for TX16s

RadioMaster 5000mah 2s Li-ion pack is the perfect battery for your receiver, safer as Lipo, stronger and bigger capacity. but as well can be used for TX16s tx lipo
Offering longer run times and safer use when compared to Li-poly batteries. Li-ion batteries typically offer higher energy density and are well suited to lower current draw applications.

The RadioMaster 5000mah pack coupled with the internal charging capabilities of the TX16s offer convenience and peace of mind charging for hours of flying enjoyment.

Our battery includes an XT30 output plug that is the ideal length for use with external modules such as the TBS Crossfire.

Specifications:

  • Capacity: 5000mah
  • Watt Hours: 37wh
  • Voltage: 7.4v
  • Cells: 2 x 21700 Li-ion 3.7v 18.5Wh
  • Connector: JST-XH and XT30
  • Weight:150g
  • Size: 72mm x 42mm x 22mm
  • Charge current: Max 2amp

€22.00

Inc. VAT
Quantity
RadioMaster CNC Metal Upgrade Set Replacement Parts for TX16S Transmitter Red, Blue, Purple, Silver

RadioMaster CNC Metal Upgrade Set Replacement Parts for TX16S Transmitter Red, Blue, Purple, Silver

This is a kit of CNC parts to let you customize your TX16S to give it a unique look and premium feel.

An optional CNC, anodized metal parts set to upgrade your RADIOMASTER TX16S transmitter. Includes a folding carry handle, gimbal fascia's, roller wheel, stick knobs, rotary knobs, screws, washers, and much much more. Make your transmitter stand out from the crowd with one of these upgrade sets.

Description:

Brand Name: RadioMaster

Item Name: Upgrade Set

Material: CNC Metal

Color: Silver/Red/Blue/Purple

Weight: 134g

Compatible: for TX16S Transmitter

€69.90

Inc. VAT
Quantity
RadioMaster CNC Metal Upgrade Set Replacement Parts for TX16S Transmitter with Leather Grips

RadioMaster CNC Metal Upgrade Set Replacement Parts for TX16S Transmitter with Leather Grips

This is a kit of CNC parts to let you customize your TX16S to give it a unique look and premium feel. on top you get the real leather grips which is a nice upgrade to have.

An optional CNC, anodized metal parts set to upgrade your RADIOMASTER TX16S transmitter. Includes a folding carry handle, gimbal fascia's, roller wheel, stick knobs, rotary knobs, screws, washers, and much much more. Make your transmitter stand out from the crowd with one of these upgrade sets.

Description:

Brand Name: RadioMaster

Item Name: Upgrade Set

Material: CNC Metal+ grips made from Leather

Color: Silver/Red/Blue/Purple+ leather grips


Compatible: for TX16S Transmitter

€80.00

Inc. VAT
Quantity
RadioMaster ER6G ExpressLRS PWM receiver (6 channels)

RadioMaster ER6G ExpressLRS PWM receiver (6 channels)

Please consult Local Telecom regulations when using this item!

Features

  • Based on the Revolutionary ExpressLRS System
  • High performance, high reliability, flexible configuration, fast response speed and ultra-long range
  • Support 8 PWM Channels
  • Optimized ground up PCB design
  • Automatically voltage telemetry of external battery voltage or built-in receiver voltage
  • ER8GV receiver is built-in high-precision air pressure sensor (Vario)
  • Supports Wi-Fi updates and WEBUI configuration
  • Reserve 4pin CRSF input port
  • High quality 2.54 mm connector
  • Standard 15 cm High Sensitivity Antenna
  • For fixed-wing aircraft and gliders

Specifications:

  • Item: ER8G 2.4GHz ELRS PWM Receiver
  • Power supply: DC 3.5 - 8.4V
  • Antenna type: 15cm high sensitivity antenna
  • Wireless protocol: ExpressLRS 3.3.0 pre-installed
  • Output channel: 6CH PWM
  • Telemetry power: maximum 50mw (LUA can be set)
  • Battery voltage detection range: DC 3.0 - 26V
  • Weight: 5.0 grams
  • Dimensions:42x13x8mm
  • Firmware: Device Category: Radiomaster 2.4Ghz / Device: Radiomaster ER8G


This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

€36.90

Inc. VAT
Quantity
RadioMaster ER8G ExpressLRS PWM receiver (8 channels)

RadioMaster ER8G ExpressLRS PWM receiver (8 channels)

Please consult Local Telecom regulations when using this item!

Features

  • Based on the Revolutionary ExpressLRS System
  • High performance, high reliability, flexible configuration, fast response speed and ultra-long range
  • Support 8 PWM Channels
  • Optimized ground up PCB design
  • Automatically voltage telemetry of external battery voltage or built-in receiver voltage
  • ER8GV receiver is built-in high-precision air pressure sensor (Vario)
  • Supports Wi-Fi updates and WEBUI configuration
  • Reserve 4pin CRSF input port
  • High quality 2.54 mm connector
  • Standard 20 cm High Sensitivity Antenna
  • For fixed-wing aircraft and gliders

Specifications:

  • Item: ER8G 2.4GHz ELRS PWM Receiver
  • Power supply: DC 3.5 - 8.4V
  • Antenna type: 20cm high sensitivity antenna
  • Wireless protocol: ExpressLRS 3.3.0 pre-installed
  • Output channel: 8CH PWM
  • Telemetry power: maximum 100mw (LUA can be set)
  • Battery voltage detection range: DC 4.0 - 35V
  • Weight: 12 grams
  • Dimensions: 60*13.5*13mm
  • Firmware: Device Category: Radiomaster 2.4Ghz / Device: Radiomaster ER8G


This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

€42.90

Inc. VAT
Quantity
RadioMaster R81 2.4GHz 8CH FULL range SBUS Nano Receiver Compatible FrSky D8 RSSI for RC Drone

RadioMaster R81 2.4GHz 8CH FULL range SBUS Nano Receiver Compatible FrSky D8 RSSI for RC Drone

RadioMaster R81 2.4GHz 8CH FULL range SBUS Nano Receiver Compatible FrSky D8 RSSI for RC Drone

  • Channels: 8
  • Frequency range: 2400-2483.5Mhz
  • Power input range: 4.5-6V
  • Signal format: Frsky D8 Compatible
  • Output format: SBUS
  • RSSI: RSSI on Ch9 of Sbus Output
  • Control distance: more than 1km
  • Antenna length: Approximately 6cm
  • Size: 17x11mm
  • Weight: 2grams

€19.00

Inc. VAT
Quantity
Radiomaster R84 4CH Frsky D8 Compatible PWM Receiver

Radiomaster R84 4CH Frsky D8 Compatible PWM Receiver

This R84 PWM Receiver has 4 channels and is Frsky D8 compatible, offering a range suitable for both drone and RC modelers.

  • Signal format: Frsky D8 Compatible
  • Frequency range: 2400-2483.5Mhz
  • Power input range: 4.5-8.4V
  • Range: more than 1km
  • Antenna length: 6cm
  • Output format: PWM
  • Weight: 2 grams
  • Size: 17x11mm
  • Channels: 4

€24.90

Inc. VAT
Radiomaster R86 6CH Frsky D8 Compatible PWM Receiver

Radiomaster R86 6CH Frsky D8 Compatible PWM Receiver

This R86 PWM Receiver has 6 channels and is Frsky D8 compatible, offering a range suitable for both drone and RC modelers.

Specifications

  • Signal format: Frsky D8 Compatible
  • Frequency range: 2400-2483.5Mhz
  • Channels: 6 channels (PWM)
  • Power input range: 4.5-8.4V
  • Range: more than 1km
  • Antenna length: 15 cm
  • Size: 28x16.5x11mm
  • Output format: PWM
  • Weight: 4.8 grams

€23.00

Inc. VAT
Quantity
RadioMaster Real Leather Side Grips Brown color, Pair

RadioMaster Real Leather Side Grips Brown color, Pair

1 Pair Brown Original RadioMaster Leather Side Grips Replacement Parts for TX16S Transmitter

€14.99

Inc. VAT
Quantity
RadioMaster Real Leather Side Grips COW color, Pair

RadioMaster Real Leather Side Grips COW color, Pair

1 Pair COW Original RadioMaster Leather Side Grips Replacement Parts for TX16S Transmitter

€14.99

Inc. VAT
Quantity
RadioMaster RP2 ExpressLRS 2.4ghz Nano Receiver with onboard Ceramic SMT Antenna

RadioMaster RP2 ExpressLRS 2.4ghz Nano Receiver with onboard Ceramic SMT Antenna

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience.

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today's pilots have come to expect.

The RP1 and RP2 2.4GHz ELRS nano series receivers are open-source receivers based on ExpressLRS. The Nano receivers, first developed by Jye Smith from the ExpressLRS development team, feature ESP8285 MCU and SX1280 RF chip. The RP1 has a UFL antenna socket for full-range antenna use. The RP2 has a built-in ceramic antenna which is super light and small in size and ideal for racing.

The RP1 and RP2 feature WIFI built in so you can upgrade firmware by WIFI and configure the Receiver via the built-in WebUI with your PC or mobile phone.

Due to the low-latency and high-refresh-rate RF module, the RP1 and RP2 are ideal for FPV races or Long Range. Suitable for many models due to the ultra-light and Nano size, these receivers can fit just about anywhere!

Features

  • Optimized PCB design for better heat dissipation.
  • LNA for better receiver range.
  • PA for better telemetry range.
  • Antenna Diversity for improved signal stability and range.
  • Built-in a TCXO (temperature compensated crystal oscillator)

    Specification
Item: RP2 Nano ExpressLRS 2.4ghz Receiver
    • Type: ISM
    • MCU: EPS8285
    • RF Chip: SEMTECH SX1281
    • Telemetry RF power: 10mW
    • Antenna: On Board SMT Antenna
    • Antenna: 65mm 2.4ghz T Antenna
    • Frequency Range: 2.404 - 2.479 Ghz
    • Maximum receive refresh rate: 500Hz/F1000Hz
    • Minimum receiver refresh rate: 25Hz
    • Working voltage: 5v
    • Weight: 0.55g (On Board antenna)
    • Dimension: 13mm*11mm*7mm
    • Firmware Version: ExpressLRS v2.4 pre-installed
    • FW Target: RadioMaster RP1/2 2400 RX
    • Bus interface: CRSF

      Package Includes
      • 1 * RP2 ExpressLRS 2.4ghz Nano Receiver
      • 1 * User Manual
      • 1 * CRSF wire


This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

€19.00

Inc. VAT
Quantity
RadioMaster RP3 ExpressLRS 2.4ghz Nano Receiver

RadioMaster RP3 ExpressLRS 2.4ghz Nano Receiver

Please consult Local Telecom regulations when using this item!

The RadioMaster RP series receivers are built-in a TCXO (temperature-compensated crystal oscillator) now, which ensures reliable, stable, and accurate signal reception, allowing for superior performance in demanding environments and enhancing the flight experience.

The RadioMaster RP series of receivers are designed with size, ease of use and range in mind. Utilizing ExpressLRS 2.4ghz Open-source firmware the RP series of nano receivers deliver features and range today's pilots have come to expect.

Developed around the ESP8285 MCU and SX1280IMLTRT RF Chip the RP series offer Lora and FLRC 2.4ghz RF links offering incredible range and low latency. With Wifi built-in FW updates can be done on your craft without the need to remove the receiver. Binding can be done using a bind phrase meaning no more bind plugs or fiddly button presses while trying to plug in your battery.

The RP3 receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance and antenna switching for antenna diversity.

Features

  • Optimized PCB design for better heat dissipation.
  • LNA for better receiver range.
  • PA for better telemetry range.
  • Antenna Diversity for improved signal stability and range.
  • Built-in a TCXO (temperature compensated crystal oscillator)

    Specification
  • Item: RP3 Diversity Receiver
  • Type: ISM
  • MCU: ESP8285
  • RF Chip: SX1281
  • Telemetry RF power: Max 100mw
  • Antenna: 65mm 2.4ghz T Antenna x 2
  • Frequency Range: 2.404 - 2.479 Ghz
  • Maximum receive refresh rate: 500Hz / F1000Hz
  • Minimum receiver refresh rate: 25Hz
  • Working voltage: 5v
  • Weight: 4.6g (Including two antenna)
  • Dimension: 22mm*13mm*4mm
  • Firmware Version: ExpressLRS v3.0 pre-installed
  • FW Target: RadioMaster RP3 Diversity 2400 RX
  • Bus interface: CRSF


This receiver works with all 2.4GHz ExpressLRS transmitters on the market.

€27.00

Inc. VAT
Quantity
Radiomaster TX16S Hall sensor MAX edition Carbon face plate with Red CNC parts Leather Grips

Radiomaster TX16S Hall sensor MAX edition Carbon face plate with Red CNC parts Leather Grips

TX16S MAX edition 16CH Multi-protocol Carbon face plate with Red CNC parts and Black Leather Grips

The Radiomaster Tx16S. Equipped with large color screen, full size hall sensor gimbals, built-in USB-C charging port and multiprotocol transmitting module for all your favorite devices with FRSKY D8 and D16 (both FCC and LBT!), Spektrum DSMX, Flysky AFHDS2A and Futaba SFHSS and much more. Of course you can also place a TBS Crossfire module (not included) in the back of the transmitter. The RadiomasterRC Tx16S is officially supported by the OpenTX team

Why choose TX16S?

  •     Built in USB-C Charging
  •     Touch Panel
  •     USB-C Data/simulator port
  •     Bigger battery compartment
  •     External SD card slot
  •     2 X UART ports for updates and DIY
  •     Improved menu navigation with Page back and forward
  •     Grip Ergonomic design
  •     Better switch quality and placement design
  •     Better sliders with good center feedback
  •     Full Size (not small short throw) HALL gimbal with CNC Aluminum face
  •     Official OpenTX support
  •     Official Multi-module support
  •     Improved speaker circuit (no noise)
  •     Included EPP carry box

​Description

  1. Channel: 16CH
  2. Mode: Mode2- can be changed
  3. Size: 183*212*66 mm
  4. Weight: 736g (without battery)
  5. Voltage: DC7-8.4V
  6. Battery Compartment: 25*52*97mm
  7. 2 x18650 (tray included) , 21700 7.4v 2s Pack or 7.4v 2s Lipoly (Batteries not included)
  8. Current: 400mah (excluding external module)
  9. External Micro SD slot: Card Included
  10. 2 x External UART Expansion Ports

Features

  • STM32F429BIT6 MCU
  • Industrial grade 4.3 inch 480*272 outdoor readable color touch panel screen
  • Compatible with OpenTX
  • Wheel menu button
  • Full Size High Quality HALL sensor gimbals with CNC Aluminum Facias
  • Internal Multi-protocol RF System
  • Full Speed Native TBS Crossfire support (400K)
  • Supports Telemetry (Protocol and Receiver dependent)
  • Memory 16M (can be expanded by Micro SD card)
  • Voice function
  • Vibration reminder function
  • Improved JR module slot
  • 6-Flight Mode Buttons (Pixhawk and more!)
  • Three-color LED status display
  • USB-C Charging port.
  • USB-C Simulator and PC connection port
  • External UART ports to expand the capabilities of your radio.

Internal Multi-protocol RF System

Cypress Semiconductor CYRF6936: DSM/DSMX, Walkera Devo

Texas Instruments CC2500: FrSky, Futabas SFHSS

Amiccom A7105: FlySky, FlySky AFHDS2A, Hubsan

Nordic Semiconductor NRF24L01: HiSky, Syma, ASSAN and most other Chinese models

RF Chip Data

The TX16S internal RF system features the CC2500, NRF24L01, A7105 and CYRF6936 RF Chip modules all integrated on one board. This module most of today’s prominent RF protocols (See RF Chip data below). The RadioMaster internal RF module will support firmware updates directly from the radios Operating system. No complicated update procedures.

Package included:

  • 1 x TX16S Max edition carbon version
  • 1 x USB-C Cable
  • 1 x 18650 Tray
  • 1 x Throttle Return Springs
  • Project box cover is optional( simple cover included)

€329.00

Inc. VAT