Receivers

Receivers

 Receivers for Radios , Spektrum, Futaba, Hitec, Webra

Products


  • Jeti Duplex 2.4EX R18 Receiver

    Jeti Duplex 2.4EX R18 Receiver

     Jeti Duplex 2.4EX R18 receiver including RSat2 satellite receiver.

    Power can be supplied via the built-in MPX connector, which is compatible with the Jeti Max BEC 2, or via JR/UNI connectors. The power supply voltage required is 3.2-8.4V, but please note that this voltage is not regulated, so please ensure the input voltage is regulated appropriately according to your servo specification.

    The R18 includes a single RSAT2 satellite receiver with dual antennae, which should be operated in clone mode with the PPM output mode of the satellite set to 'DIRECT' and the PPM input mode of the R18 set to PPM Input on your chosen satellite channel.

    As with all Jeti Duplex 2.4GHz receivers, an audible alert can be configured so that the Duplex transmitter module emits an alarm, should the receiver supply voltage drop below a preset level. This is configurable by connecting the Jeti Box to the Tx module and this particular feature requires no additional sensors.

    Complete with bind-plug and MPX plug with two pieces of heatshrink.
    For a stable and reliable power source, we recommend the Max BEC range of voltage regulators. Alternatively you may wish to use two A123 LiFePO4 batteries, depending on your power requirements.

    Technical Details for Jeti Duplex 2.4EX R18 Receiver

    • Dimensions (mm)    62x38x16
    • Antennae Count    2
    • Antennae Length    400.00mm (15.75")
    • Channel Outputs    18
    • Temperature Range min. (°C)    -10
    • Jeti Box Compatible (JBC)    Yes
    • Temperature Range max. (°C)    85
    • Supply Voltage min.    3.2V
    • Supply Voltage max.    8.4V
    • Average Current (mA)    40
    • Transmission of Telemetric Data    Yes
    • Satellite receiver support    Yes
    • Power output (dBm)    20
    • Receiver Sensitivity (dBm)    -106
    • Weight    34.0g (1.2oz.)
    SKU: JDEX-R18
    €194.90
    inc. VAT

     LOW STOCK
  • Jeti Duplex 2.4EX R9 channel full-range receiver

    Jeti Duplex 2.4EX R9 channel full-range receiver

    9 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    Specification

    • Weight [g]:  13
    • Dimensions [mm]: 48 x 23 x 10
    • Number of channels: 9
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 200
    • Supply Voltage [V]: 3,2 - 8,4
    • Average Current [mA]: 30
    • Satellite receiver support: Yes
    • Output Power [dBm]: 15
    • Receiver Sensitivity [dBm]: -106
    SKU: JDEX-R9
    €95.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex 2.4EX R9 channel full-range receiver W/antenna 40cm

    Jeti Duplex 2.4EX R9 channel full-range receiver W/antenna 40cm

    Jeti Duplex 2.4EX R9 channel full-range receiver W/antenna 40cm

    Programmable duplex 2.4EX 9 channel receiver 2.4GHz:

    Bi-directional communication with the transmitter
    Transfer of the telemetry data to the transmitter (read out via the JETIBOX)
    Receiver supply voltage indication at the transmitter, and adjustable value for triggering an alarm
    A plurality of receivers to a transmitter possible receivable up to a total of 16 channels
    Adjustable Failsafe
    Servo channels freely assignable
    Servo lanes, center position and duration adjustable
    free mixers allocation of channels
    Expo the channels can be set
    Activation within a quarter second after switching
    Connection for sensors (8 channel expander bix to 8 sensors)
    Programmable with the JETI Box directly or wireless via transmitter

    DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and compatible, of course, full of the previous components .
    The EX Series provides a significant extension of the possibilities for the transmission of telemetry data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor receive user-friendly design a better overview of the operational status of your model, facilitating the setting of the system components and the way an easier processing, imaging and analysis capability of the (recorded) flight data

    Specifications:

    • Dimensions 23x48x9,5mm
    • Weight     13g
    • Antenna length     2x 400mm
    • Outputs 9
    • Temperature range -10 to 85 ° C
    • Input voltage     3.2 - 8.4V
    • Average power consumption 40 mA
    • Real-time telemetry transmission Yes
    • Programming JETIBOX
    • Satellite receiver Yes
    • Transmission power 20 dBm
    • Receiver Sensitivity -106 dBm

    Alarm settings:
    With the JETI Box alarm signals can be activated at (beeps by duplex RF module in the transmitter):
    Alarm waste Receiver supply below a set voltage value


    By connecting a current and voltage sensor to the receiver alarm can be triggered by:

    • Exceed a current value
    • Undershooting of a voltage value
    • Exceed a capacitance value
    SKU: JDEX-R9-A40
    €96.90
    inc. VAT

     72HR STOCK
  • Jeti DUPLEX 2.4EX RC Switch

    Jeti DUPLEX 2.4EX RC Switch

    JETI DUPLEX 2.4EX RC Switch

    RCSW - RC Switch is a wireless switch designed especially for JETI model products (BEC stabilizers, Central Box and other accessories) that increase the comfort of model control. RC Switch can be easily controlled using DC/DS transmitters and it can be simply used as a replacement of the magnetic key.

    Compatible devices: SBEC 40, DPS 40, SPS 20, DSM 10, Central Box 200, Central Box 400, Master Switch etc.

    Switching is indicated by a green LED that is visible through the opening on the side of the RC Switch.

    Setting the polarity of the switch is specific for each JETI model product, in the chart below there is a list of several supported devices and their RC Switch settings for DC and DS transmitters.

    SKU: JDEX-RCSW
    €72.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex R6 EPC A40 Receiver

    Jeti Duplex R6 EPC A40 Receiver

    6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors or by the external MPX connector.

    Antenna length: 40cm

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

    • Weight [g]: 11
    • Dimensions [mm]: 45 x 24 x 12
    • Number of channels:6
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 400
    • Supply Voltage [V]: 3,2 - 8,4
    • Average Current [mA]:40
    • Satellite receiver support: No
    • Output Power: 15 dBm
    • Receiver Sensitivity: -106 dBm
    SKU: JDEX-R6EPCA40
    €77.90
    inc. VAT

     LOW STOCK
  • Jeti Duplex R7 Nano Receiver

    Jeti Duplex R7 Nano Receiver

    JETI Duplex R7 Nano Receiver Weight [g] 1 (2) Dimensions [mm] 30 x 18 x 5 Number of channels 7 Telemetry Yes Operational temperature [°C] -10 ... 85 Compatible protocols DUPLEX 2.4GHz EX, EX Bus Antenna Length [mm] 1 x 32 Supply Voltage [V] 3,2 - 8,4 Average Current [mA] 30 Satellite receiver support No Output Power [dBm] 6 Receiver Sensitivity [dBm] -98

    SKU: JDEX-R7N
    €62.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex receiver 2.4EX R18 2.4GHz + DRsat2 EX

    Jeti Duplex receiver 2.4EX R18 2.4GHz + DRsat2 EX

    Jeti Duplex receiver 2.4EX R18 2.4GHz + DRsat2 EX

    18 channel full-range receiver compatible with Jeti EX & EX bus protocols. Support telemetry functions. Power supply is provided by MPX connector or standard JR connectors.

    Additional features:
    PPM input (Sat1)
    PPM input or output (Sat2)
    Jeti Duplex Rsat2 is included in the package

    The DUPLEX EX line of receivers is Intended for surgery with DUPLEX Tx transmitter modules in the 2,4GHz band-and are fully compatible with the previous version of the DUPLEX.
    Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely Call new aspects in the model remote control branch.
    One of the most important advantages is the operational without crystal, more over the low susceptibility towards interference, the high range up to the limit of visibility and the Possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system.
    Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only.
    This PPM signal is ford heron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment Which requires a PPM signal at the input.

    DUPLEX EX system is fully compatible with the previous version of the DUPLEX.

    Specification:

    • Manufacturer: Jeti
    • Quiescent current [mA]: 40
    • Receive Sensitivity [dBm]: -106
    • Antenna number: 2    2
    • Antenna length [mm]: 400
    • channels: 18
    • Satellite receiver possible
    • Real-time telemetry
    • Transmission power [dBm]: 20
    • Type:     duplex EX
    • Rated voltage up to [V]: 8.4
    • Rated voltage [V]: 3.2
    • Weight [g]: 30
    • Height [mm]: 16
    • Width [mm]: 38
    • Length [mm]: 62
    SKU: JETI-DR18
    €189.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex receiver 2.4EX REX3 20cm antenna

    Jeti Duplex receiver 2.4EX REX3 20cm antenna

    Jeti Duplex receiver 2.4EX REX3 with 20cm antenna

    DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and , of course, fully compatible with the existing components .
    The EX Series provides a significant expansion of the possibilities of transmission of telemetric data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor software user-friendly way a better overview of the operational status of your model, a facilitated setting the system components and the way a facilitated processing, imaging and analysis possibility of (recorded) flight information.

    Programmable Duplex 2.4EX REX3 receiver 2.4GHz:

    • bi-directional communication with the transmitter
    • Transfer of telemetry data to the transmitter
    • Voltage indicator Receiver supply at the transmitter and adjustable value for triggering an alarm
    • multiple recipients possible at a transmitter, be received up to 16 channels
    • Adjustable Failsafe
    • Servo channels freely assignable
    • Servo travel center position and duration adjustable
    • free mixer channels are assigned
    • Expo of the channels can be set  
    • internal memory for data logging and
    • control signals
    • integrated expander for up to 3 sensors
    • Supported protocols: PPM
    • , EXBUS, EX, ..
    • programmable features of the slots
    • support the direct entries
    • compact dimensions
    • 32 bit processor
    • full coverage
    • programmable via the JETIBOX and wirelessly
    • via the duplex DC / DS transmitter


    Specifications:

    • Dimensions: 40x22x7mm
    • Weight:  7.5g
    • Antenna length: 2x 400mm
    • Outputs: 3
    • Temperature range: -10 To 85 ° C
    • Input voltage: 3.2 - 8.4V
    • Average current consumption:  mA
    • Real-time telemetry: Yes
    • Programming: JETIBOX
    • Satellite receiver: Yes
    • Transmission power: 15 dBm
    • Receive Sensitivity: -106 dBm
    SKU: JDEX-RR3-A20
    €69.90
    inc. VAT

     IN STOCK
  • Jeti Duplex receiver 2.4EX REX3 with 40cm antenna

    Jeti Duplex receiver 2.4EX REX3 with 40cm antenna

    Jeti Duplex receiver 2.4EX REX3 with 40cm antenna

    DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and , of course, fully compatible with the existing components .
    The EX Series provides a significant expansion of the possibilities of transmission of telemetric data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor software user-friendly way a better overview of the operational status of your model, a facilitated setting the system components and the way a facilitated processing, imaging and analysis possibility of (recorded) flight information.

    Programmable Duplex 2.4EX REX3 receiver 2.4GHz:

    • bi-directional communication with the transmitter
    • Transfer of telemetry data to the transmitter
    • Voltage indicator Receiver supply at the transmitter and adjustable value for triggering an alarm
    • multiple recipients possible at a transmitter, be received up to 16 channels
    • Adjustable Failsafe
    • Servo channels freely assignable
    • Servo travel center position and duration adjustable
    • free mixer channels are assigned
    • Expo of the channels can be set  
    • internal memory for data logging and
    • control signals
    • integrated expander for up to 3 sensors
    • Supported protocols: PPM
    • , EXBUS, EX, ..
    • programmable features of the slots
    • support the direct entries
    • compact dimensions
    • 32 bit processor
    • full coverage
    • programmable via the JETIBOX and wirelessly
    • via the duplex DC / DS transmitter


    Specifications:

    • Dimensions: 40x22x7mm
    • Weight:  7.5g
    • Antenna length: 2x 400mm
    • Outputs: 3
    • Temperature range: -10 To 85 ° C
    • Input voltage: 3.2 - 8.4V
    • Average current consumption:  mA
    • Real-time telemetry: Yes
    • Programming: JETIBOX
    • Satellite receiver: Yes
    • Transmission power: 15 dBm
    • Receive Sensitivity: -106 dBm
    SKU: JDEX-RR3-A40
    €73.90
    inc. VAT

  • Jeti Duplex Satellite for 2.4EX Type2

    Jeti Duplex Satellite for 2.4EX Type2

    Jeti Duplex Satellite for 2.4EX Type2

    Satellite receiver for Duplex R9, R10, R11EPC, R12EPC, R14 and Duplex R18 (connection by cable).
    PPM output is available on a single line.

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    DUPLEX  EX System is fully compatible with the previous version of the DUPLEX.

    Specification:
     

    • Manufacturer: Jeti
    • Quiescent current [mA]: 35
    • Receiving Sensitivity [dBm]: -106
    • Antenna number:
    • Antenna length [mm]: 200
    • Channels: 16
    • Transmission power [dBm]: 20
    • Type:    Duplex EX
    • Rated voltage up to [V]: 8.4
    • Rated voltage [V]: 3.2
    • Weight [g]: 10
    • Height [mm]: 6
    • Width [mm]: 23
    • Length [mm]: 35
    SKU: JDEX-RS2
    €64.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex Satellite for Type R.sub.sat 900

    Jeti Duplex Satellite for Type R.sub.sat 900

    Jeti Duplex Satellite for Type R.sub.sat 900

    Only the DC 24 transmitter have a backup transmission system for the highest data transfer security and reliability.
    It therefore represents the first dual-band radio system RC new generation.

    Specification:

    • Weight (g): 11
    • Dimensions (mm): 0x22x7
    • Temperature range (° C): -10 - 85
    • Voltage range (V): 3.2 to 8.4
    • Current consumption (mA): 30
    • Frequency range (MHz):     863-870
    • Logs:     EX-bus, PPM, UDI
    SKU: JDEX-RS-900
    €71.90
    inc. VAT

     72HR STOCK
  • Jeti Enlink 2RS

    Jeti Enlink 2RS

    Jeti Enlink 2RS

    EnLink 2RS is a device for increasing safety and reliability of radio controled models to the highest level. Parallel connection of systems that are detached maximally leads to the significant increase in reliability.
    EnLink2RS is constructed especially for installing to systems with parallel sorting of two receivers in the model.


    SKU: J-ENLINK-2RS
    €37.90
    inc. VAT

     LOW STOCK
  • Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

    Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

    Jeti Receiver Duplex 2.4EX R11EPC 2,4GHz

    11 channel full-range receiver compatible with JETI EX & EX Bus
    protocols. Supports telemetry functions and contains a separate battery power connector.

    Additional features:

    • PPM
    • input (Sat1)

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM
    signal only. This PPM
    signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM
    signal at the input.

    DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

    Manuals - Duplex EX

    • JETI Duplex EX Receiver Manual V3.22 [EN, DE] - English & German user manual for the receivers version 3.22 (6/2014)
    • Declaration of Conformity CZ+EN - Standards compliance
    • JETI Duplex EX Manual V3.0 EN+DE - English & German user manual for Tx modules and receivers (6/2011)Rx + RSat Jetibox Schema V3.0 CZ - Jetibox screen schemes of the receivers and satellites
    • Rx + Rsat Jetibox Schema V3.0 EN+DE - Jetibox screen schemes of the receivers and satellites

    Update - Receivers

    • Duplex EX - Rx V3.22 - Rx Firmware Update (4/2014) - EX Bus
    • , Log. inputs/outputs, UDI. RSAT2[3.21]: By default, PPM
    • fail-safe is set to "Off". [3.22] Telemetry logical inputs improved.
    • Duplex EX - Rx & Tx V3.04 - Rx & Tx Compatibility Firmware Update (3/2012)
    • Duplex EX - Rx V3.11 - Rx Firmware Update (5/2013) - EX Bus
    • JETI Duplex EX Manual V3.11 EN - English user manual for receivers (4/2013)
    SKU: JDEX-R11EPC
    €107.90
    inc. VAT

     LOW STOCK
  • Jeti Receiver Duplex 2.4EX R5L 2,4GHz

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz

    5 channel full-range receiver compatible with JETI EX & EX Bus protocols. This receiver is designed for operation in small and medium models. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.
    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    DUPLEX  EX System is fully compatible with the previous version of the DUPLEX.

    Specification:
     

    • Quiescent current [mA]:    30
    • Receive Sensitivity [dBm]:    -106
    • Antenna number:    2
    • Antenna length [mm]:    100
    • Channels:    5
    • Satellite receiver possible:    
    • Real-time telemetry:    
    • Transmission power [dBm]:    15    
    • Type:    Duplex EX
    • Rated voltage up to [V]:    8.4
    • Rated voltage [V]:    3.2
    • Weight [g]:    5.4
    • Height [mm]:    7
    • Width [mm]:    20
    • Length [mm]:    47
    •  
    SKU: JDEX-R5L
    €63.90
    inc. VAT

     IN STOCK
  • Jeti Receiver Duplex 2.4EX R5L 2,4GHz W/antenna 20cm

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz W/antenna 20cm

    Jeti Receiver Duplex 2.4EX R5L 2,4GHz W/antenna 20cm

    Programmable duplex 2.4EX 9 channel receiver 2.4GHz:

    • bi-directional communication with the transmitter
    • Transfer of the telemetry data to the transmitter (read out via the JETIBOX)
    • Receiver supply voltage indication at the transmitter, and adjustable value for triggering an alarm
    • a plurality of receivers to a transmitter possible receivable up to a total of 16 channels
    • adjustable Failsafe
    • Servo channels freely assignable
    • Servo travels, center position and duration adjustable
    • free mixers allocation of channels
    • Expo the channels can be set
    • Activation within a quarter second after switching
    • Connection for sensors (8 channel expander bix to 8 sensors)
    • programmable with the JETI Box directly or wireless via transmitter
    • light version for indoor models

    DUPLEX EX is the successor of the well known and proven Jeti DUPLEX system and compatible, of course, full of the previous components .
    The EX Series provides a significant extension of the possibilities for the transmission of telemetry data, in conjunction with the PROFI BOX or the Jeti transmitters in conjunction with the program package Flight Monitor receive user-friendly design a better overview of the operational status of your model, facilitating the setting of the system components and the way an easier processing, imaging and analysis capability of the (recorded) flight data

    Specifications:

    • Dimensions 47x20x7mm
    • Weight     5.4 g
    • Antenna length     2x 200mm
    • Outputs 5
    • Temperature range -10 to + 85 ° C
    • Input voltage 3.2 - 8.4V
    • Average Power Consumption 30 mA
    • Real-time telemetry transmission Yes
    • Programming JETIBOX
    • Satellite receiver No
    • Transmission power 15 dBm
    • Receive Sensitivity -106 dBm

    Alarm settings:
    With the JETI Box alarm signals can be activated at (beeps by duplex RF module in the transmitter):
    Alarm waste Receiver supply below a set voltage value
    By connecting a current and voltage sensor to the receiver alarm can be triggered by:

    • Exceed a current value
    • Undershooting of a voltage value
    • Exceed a capacitance value

     

    SKU: JDEX-R5L-A20
    €65.90
    inc. VAT

     IN STOCK
  • Jeti Receiver Duplex 2.4EX REX10

    Jeti Receiver Duplex 2.4EX REX10

    JETI Receiver Duplex 2.4EX REX10

    10 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

    Additional features:

    • PPM input
    • PPM output
    • Integrated expander for EX & EX Bus devices
    • UDI digital output

    JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
    The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
    The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers.
    For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
    The REX receivers are fully compatible with the previous generation of the Duplex equipment.

    Specification.

    • Weight [g] 16
    • Dimensions [mm] 51 x 28 x 11
    • Number of channels 10
    • Telemetry Yes
    • Operational temperature [°C]     -10 ... 85
    • Compatible protocols DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm] 2 x 200
    • Supply Voltage [V] 3,5 - 8,4
    • Average Current [mA] 75
    • Satellite receiver support Yes
    • Output Power [dBm] 15
    • Receiver Sensitivity [dBm] -106
    SKU: JDEX-RR10
    €103.90
    inc. VAT

     72HR STOCK
  • Jeti Receiver Duplex 2.4EX REX12

    Jeti Receiver Duplex 2.4EX REX12

    JETI Receiver Duplex 2.4EX REX12

    12 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

    Additional features:

    • PPM input
    • PPM output
    • Integrated expander for EX & EX Bus devices
    • UDI digital output

    JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
    The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
    The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers.
    For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
    The REX receivers are fully compatible with the previous generation of the Duplex equipment.

    Specification.

    • Weight [g] 24
    • Dimensions [mm] 51 x 28 x 11
    • Number of channels 12
    • Telemetry Yes
    • Operational temperature [°C]     -10 ... 85
    • Compatible protocols DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm] 2 x 400
    • Supply Voltage [V] 3,5 - 8,4
    • Average Current [mA] 75
    • Satellite receiver support Yes
    • Output Power [dBm] 15
    • Receiver Sensitivity [dBm] -106
    SKU: JDEX-RR12
    €124.90
    inc. VAT

     LOW STOCK
  • JETI Receiver Duplex 2.4EX REX6 Assist

    JETI Receiver Duplex 2.4EX REX6 Assist

    6 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

    The REX A receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multicopters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.


    Features:

    • Up to 16 stabilized airplane channels.
    • Support for different multicopter types – from tricopters to octocopters.
    • Up to 3 adjustable flight modes, options for stabilizing the horizon and altitude.
    • In-flight gain tuning using free channels.
    • Using the latest 3-axis gyroscope, 3-axis accelerometer and barometric altimeter.
    • Support for LED strip consisting of WS2812 chips.
    • Support for external camera gimbal driven by servos.
    • Intelligent fail-safe.
    • Vibration analysis.
    • Full set-up options with DC/DS transmitters or via PC.
    • Available telemetry: Receiver voltage, signal quality, G-force, attitude orientation.
    • Support of telemetry and up to 3 sensors connected directly.

    Specifications:

    • Weight [g]: 11
    • Dimensions [mm]: 38 x 25 x 11
    • Number of channels: 6
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 100
    • Supply Voltage [V]: 3,5 - 8,4
    • Average Current [mA]: 75
    • Satellite receiver support: Yes
    • Output Power [dBm]: 15
    • Receiver Sensitivity [dBm]: -106
    • Assist stabilization: Yes
    SKU: JDEX-RR6A
    €129.90
    inc. VAT

     72HR STOCK
  • JETI Receiver Duplex 2.4EX Rex7 Assist

    JETI Receiver Duplex 2.4EX Rex7 Assist

    7 channel full-range receiver with integrated Assist stabilization, compatible with JETI EX & EX Bus protocols. Supports telemetry functions and stabilization for airplane and multicopter models.

    The REX A receivers enhance the REX series of receivers and extend it with the intelligent flight stabilization feature, which is designed for airplane models and multicopters. This stabilization works in all three axes of the model and facilitates flying in windy or otherwise challenging conditions. Aerobatic maneuvers will be more accurate and smoother. With the help of several flight modes, which are also suitable for beginner pilots, flying practice will be really easy.


    Features:

    • Up to 16 stabilized airplane channels.
    • Support for different multicopter types – from tricopters to octocopters.
    • Up to 3 adjustable flight modes, options for stabilizing the horizon and altitude.
    • In-flight gain tuning using free channels.
    • Using the latest 3-axis gyroscope, 3-axis accelerometer and barometric altimeter.
    • Support for LED strip consisting of WS2812 chips.
    • Support for external camera gimbal driven by servos.
    • Intelligent fail-safe.
    • Vibration analysis.
    • Full set-up options with DC/DS transmitters or via PC.
    • Available telemetry: Receiver voltage, signal quality, G-force, attitude orientation.
    • Support of telemetry and up to 3 sensors connected directly.

    Specifications:

    • Weight [g]:13
    • Dimensions [mm]: 42 x 28 x 11
    • Number of channels: 7
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 200
    • Supply Voltage [V]: 3,5 - 8,4
    • Average Current [mA]: 75
    • Satellite receiver support: Yes
    • Output Power [dBm]: 15
    • Receiver Sensitivity [dBm]: -106
    • Assist stabilization: Yes
    SKU: JDEX-RR7A
    €144.90
    inc. VAT

     72HR STOCK
  • Jeti Universal Switch 6A opto

    Jeti Universal Switch 6A opto

    Jeti Universal Switch 6A opto

    The switch SP 06 opto has been specifically designed for switching purposes of auxiliary functions, such as on board glow plug heating systems and miscellaneous lighting systems etc. in model airplanes, model ships, and model cars. The switched loads can be of ohmic, inductive or capacitive character. The switching moment is signalled by  a LED.

    Specification:
     

    • Weight [g]: 9
    • Dimensions [mm]: 27 x 15 x 5
    • Sustained current [A]:   6
    • Peak current (max 30s) [A]: 10
    • Telemetry: No
    • Operational temperature [°C]: -10 ... 70
    • Recommended input voltage [V]: 3,5 ... 16
    • Input voltage max. [V]:   16
    SKU: J-SP06-OPTO
    €24.90
    inc. VAT

     LOW STOCK
  • Jumper SF410-Mini 4CH Full Range S-FHSS Receiver w/ SBUS PWM Output

    Jumper SF410-Mini 4CH Full Range S-FHSS Receiver w/ SBUS PWM Output

    The Jumper SF series of receivers offer a high quality yet affordable S-FHSS solution for RC pilots. The SF410-Mini is ideal for ultralight flight systems that need a tiny receiver solution.

    Specification:

    • Specs
      Working voltage: 3.6~7.5V
      Working current: 20~30mA
      Working temperature: 0-70 °C
      Delay: Normal Mode 13.6mS / Special Mode 20.4mS
      Effective distance: >300km
      Weight: 1.9g
      SBUS: Yes
    SKU: JU-SF410
    €16.90
    inc. VAT

     LOW STOCK
  • Jumper SF610 6CH Full Range S-FHSS Receiver SBUS PWM Output

    Jumper SF610 6CH Full Range S-FHSS Receiver SBUS PWM Output

    The Jumper SF series of receivers offer a high quality yet affordable S-FHSS solution for modelers.

    The SF Series can be used as a standard PWM receiver or in S.Bus mode for drones
    or fixed wing craft, robotics, boat or anything that uses an advance control system requiring S.Bus input.

    The SF series are a full range receiver featuring dual antennas for diversity reception.
    When reliable quality receivers can be had at this price why risk any alternative!

    Specification:

    • Brand Name: Jumper
    • Item Name: 2.4G 6CH Full Range Compaitble S-FHSS Receiver
    • Model: SF610
    • Working Voltage: 3.6~7.5V
    • Working Vurrent: 45~60mA
    • Working Temperature: 0-70 °C
    • Delay: Normal Mode 13.6mS
    •             Special Mode 20.4mS
    • Effective Distance: >1.8km
    • Weight: 6.8g
    • SBUS: Yes
    • Full Range: Yes
    • Dual Diversity Antenna: Yes

    Application: Compatble with Jumper T8SG/T8SG v2/T8SG v2 Plus/T8SG Lite/T12
                                                        Futaba T4YF/T6J/T6K/ T8J/T10J/T14SG/T18MZ/T18SZ
                                                       Ground System 3PL/ T3PRKA/ 4PLS/ T4PX/ T4GRS.

    SKU: JU-SF610
    €17.90
    inc. VAT

  • Jumper SF810 SFHSS/FHSS Compatible 2.4GHz 8CH Receiver w/S.BUS

    Jumper SF810 SFHSS/FHSS Compatible 2.4GHz 8CH Receiver w/S.BUS

    The Jumper SF810 has 8 PWM channels in Normal mode. In special mode, the 8th channel outputs Sbus while the remaining 7 channels output PWM.

    Features:
    Compatible with FUTABA SFHSS/FHSS 2.4GHz Transmitters
    Air systems T4YF, T6J, T6K, T6K, T8J, T10J, T14SG, T18MZ, T18SZ
    Ground system 3PL, T3PRKA, 4PLS, T4PX, T4GRS
    Two modes, Normal (all PWM) and Special (PWM and S.Buss)
    Two antennas

    Specs:

    • Working voltage: 3.6~8.5V
    • Working current: 45~60mA
    • Working temperature: 0-70 °C
    • Delay: Normal Mode 13.6mS
    •            Special Mode 20.4mS
    • Effective distance: >1.8km
    • Weight: 7.9g

    Note:
    In normal mode, the signal delay is 20.4mS, suitable for Analog servos.
    In the special mode, the delay is 13.6mS suitable for Digital servos.

    SKU: JU-SF810
    €19.90
    inc. VAT

     72HR STOCK
  • Mikado VBar Control RX-Satellite

    Mikado VBar Control RX-Satellite

    Mikado VBar Control RX-Satellite

    SKU: MIK-4882
    €59.90
    inc. VAT

     LOW STOCK

Manufacturers

Back