Receivers

Receivers

 Receivers for Radios , Spektrum, Futaba, Hitec, Webra

Products


  • Futaba R6303SB FASST S.Bus receiver

    Futaba R6303SB FASST S.Bus receiver

    This is the Futaba R6303SB 3-Channel 2.4Ghz FASST Micro S.Bus Receiver. Stop cable clutter with the innovative S.Bus system. It uses digital serial data communication technology to transmit control signals between your receiver and servos. A single S.Bus cable can carry signals to as many channels as your transmitter can handle. You no longer have to worry about plugging in the wrong servo to the wrong channel, because each servo knows what channel it is dedicated to in advance.

    S.Bus receivers are limited only by the number of channels your transmitter will handle. Don’t have S.Bus servos? No problem. SBD-1 S.Bus Decoder Cables let you use existing analog and digital servos, too. The Futaba S.Bus system is nothing short of revolutionary – and the revolution’s just beginning.

    Features:

    •   S.Bus system output and three conventional system channel outputs allows usage with conventional servos as well as S.Bus system compatible servos.
    •   When linking procedure is performed, receiver recognizes the signal mode (FASST 2.4GHz 7ch mode or 8ch/10ch/Multi Channel Mode) automatically
    •   High-speed or normal operating mode
    •   PWM 3CH (CH 1,2,3)
    •   S.BUS 16+2CH
    •   Small and light
    •   Dual antenna diversity (coaxial antenna)
    •   Full range
    •   Operating Voltage 3.5 – 8.4V’s

    Specifications:

    • Power Requirement: 3.7 – 7.4V
    • Power Voltage: 3.5 – 8.4V
    • Dimensions: 0.89 x 1.47 x 0.37" (22.5 x 37.4 x 9.3mm)
    • Weight: 0.25oz (7.2g)

     

    SKU: F1014
    €79.90
    inc. VAT

     72HR STOCK
  • Futaba R6308SBT FASST Telemetry receiver

    Futaba R6308SBT FASST Telemetry receiver

    Compact, lightweight R6308SBT 2.4 GHz FASST receiver with integral FASSTest® telemetry transmitter, for "transmitting model data back to the ground".

    In spite of its small size, the R6308SBT receiver features an integral FASSTest® telemetry transmitter, and can transmit a maximum of 32 telemetry data sets to the ground over a range of > 1000 m .
    Any existing FASST system can be converted to telemetry operation at any time by using an R6308SBT 2.4 GHz FASST telemetry receiver.
    Naturally the receiver is fitted with eight PWM outputs for normal servos. The PWM outputs are switchable, i.e. you can make use of either PWM channels 1...8 or 9...16. Two receivers can be operated in parallel to provide sixteen PWM channels.

    Channel 8 can be switched to S.BUS mode, in which case up to eighteen S-BUS servos or other devices can be connected to this output.
    Devices or sensors can be connected via the S.BUS2 socket, and up to 32 telemetry data sets can be transmitted. If two receivers are employed, the number of telemetry channels rises to 64.
    The receiver's integral transmitter sends telemetry data present at the S.BUS2 socket to the Telemetry-Box by radio; the data are then displayed on the screen, or generated in the form of audible or speech output.

    If a separate Wi-Fi-Box, No. F1667 with integral FASSTest receiver module is used, the telemetry data can also or alternatively be transmitted to a smart-phone (Android, Apple), netbook, laptop, etc., and any monitor connected to that device.

    When the receiver is connected, data such as receiver battery voltage, external voltage (max. 70 V DC) and aerial signal strength, i.e. the essential telemetry data, are automatically transmitted to the ground.
    The outstanding features of the receiver are its small size of just 47.3 x 24.9 x 14.3 mm and weight of only 13 g you could ever need.


    SKU: F1002
    €120.00
    inc. VAT

     LOW STOCK
  • Futaba R7003SB FASSTest HV receiver

    Futaba R7003SB FASSTest HV receiver

    Compact, lightweight R7003SB 2.4 GHz FASSTest receiver with integral telemetry transmitter.

    • Smaller, only 7g, lighter 3 /18 - channel 2.4GHz FASSTest S.BUS-Receiver with full range and integrated Telemetry transmitter.
    • Ultra-slim for models with narrow fuselages.
    • With the S-BUS system for up to 18 channels, making it suitable for all models from mini-helicopters to large-scale aircraft.
    • Normal PWM-output
    • The 3 PWM-Servo channels outputs are divided in 7 groups of outputs Port 1 and 2, whereby the output allocation may be freely selected.
    • S.BUS output Up to 18 of the new, programmable S-BUS servos or peripheral devices such as gyros,
    • Flybarless systems or speed controllers can be attached in series directly to this output.
    • One feed cable for all channels.
    • No cable „spaghetti“, and reduced weight.
    • All standard servos can be connected to receivers with an S.BUS PWM adapter.
    • It does not get any simpler.
    • High Response
    • Switchable output speed of the control pulse for digital servos, 6.3 ms instead of 16 ms,
    • which leads to a still shorter reaction time.
    • Aerial Diversity
    • The 2 Aerial Diversity system continuously checks the signal level at both aerial inputs and switches over in a split second to the stronger signal with no transition period.

    Telemetry

    • S.BUS2 devices or sensors can be connected via the S.BUS2 socket, and up to 32 telemetry data sets can be transmitted.
    • The receiver‘s integral transmitter sends the telemetry data present at the S.BUS2 socket to the FASSTest transmitter, where the data are displayed on-screen or generated in audible form.
    • Alternatively, the data can be transmitted to a separate Telemetry-Box.
    • When the receiver is connected, data such as receiver battery voltage, external voltage (max. 70 V DC) and aerial signal strength, i.e. the essential telemetry data, are automatically transmitted to the ground.

    Power

    • A further voltage range from 3.7…7.4 V nominal voltage, when using 7.4 LiPo-Batteries for receiver power, all connected servos must possess the appropriate voltage capability.
    • The receiver does not feature an internal servo voltage limiter for the high voltage servo voltage.

    Recommended accessory:

    • F1001100 „Extra Voltage“ connecting lead with fuse.

    Specification:

    • Frequency band 2.4 – 2.4835 GHz
    • Spot frequencies 36
    • Channel count 18
    • Channel spacing 2048 kHz
    • Transmission system FASSTest
    • Voltage 3.7...7.4 Volt (4 - 5 Nx, 2 LiFe, 1 - 2 LiPo)
    • Current 50 mA
    • Dimensions 37.4 x 22.5 x 9.3 mm
    • Aerial length 14 cm
    • Weight approx. 7,2 g


    Set contents
    Including adapter for the „Extra Voltage“ connecting lead at Port 2.
     

    SKU: F1004
    €99.00
    inc. VAT

  • Futaba R7006SB Receiver 6/18ch 2.5 GHz FASST/FASSTest

    Futaba R7006SB Receiver 6/18ch 2.5 GHz FASST/FASSTest

    Futaba’s new full range R7006SB receiver is capable of operating with either FASST or FASSTest transmission modes, and offers 6 conventional and 18 S-Bus channel outputs yet is exceptionally compact and light.

    Specifications:

    • Range: Full
    • Modulation: FASSTest & FASST
    • S.BUS / S.Bus: S.Bus & S.Bus2
    • Weight / Gewicht: 8.5g
    • Dimensions: 22.5 x 38.1 x 12.2mm
    • Voltage: 3.7 - 7.4V
    • Channels: 7 PWM or 18 S-Bus
    SKU: F-R7006SB
    €89.90
    inc. VAT

     LOW STOCK
  • Futaba R7008SB S.Bus2 2.4GHz FASSTest Receiver

    Futaba R7008SB S.Bus2 2.4GHz FASSTest Receiver

    Compact, lightweight R7008SB 2.4 GHz FASSTest receiver with integral telemetry transmitter.

    In spite of its small size of only 47.3 x 24.9 x 14.3 mm and a weight of just 13 g the R7008SB receiver is a multi-talented device. It features an integral telemetry transmitter, and can send up to 32 telemetry data sets to the ground over a range of > 1000 m.
    Naturally the receiver is fitted with eight PWM outputs for normal servos. The PWM outputs are switchable, i.e. you can make use of either PWM channels 1...8 or 9...16. Two receivers can be operated in parallel to provide sixteen PWM channels.

    Channel 8 can be switched to S.BUS mode, in which case up to eighteen S-BUS servos or other devices can be connected to this output.
    Devices or sensors can be connected via the S.BUS2 socket, and up to 32 telemetry data sets can be transmitted. If two receivers are employed, the number of telemetry channels rises to 64.

    The receiver's integral transmitter sends the telemetry data present at the S.BUS2 socket to the FASSTest transmitter, where the data are displayed on-screen or generated in audible form. If a separate Wi-Fi-Box is used, the telemetry data can also be sent by radio to a smart-phone (Android, Apple), netbook, laptop, etc., and any monitor connected to that device.

    When the receiver is connected, data such as receiver battery voltage, external voltage (max. 70 V DC) and aerial signal strength, i.e. the essential telemetry data, are automatically transmitted to the ground.

    This receiver "only" works in conjunction with the new telemetry-capable FASSTest transmitters. If you wish to use the receiver with a FASST or RASST transmitter, you need to use R6308SBT 2.4 GHz.

    SKU: F1001
    €135.00
    inc. VAT

  • Futaba R7014SB FASST/FASSTest Receiver 2.4GHz

    Futaba R7014SB FASST/FASSTest Receiver 2.4GHz

    Futaba R7014SB FASST/FASSTest Receiver 2.4GHz

    The R7014SB is Futaba's new receiver for high end models. Featuring S.Bus technology, 14 PWM channels and it is also capable of operating with FASST or FASSTest systems.

    Specifications:

    • Modulation: FASST, FASSTest
    • S.BUS: S.BUS2
    • Weight: 20.8g (0.7oz.)
    • Dimensions: 37 x 50.2 x 15.9mm (1.5 x 2.0 x 0.6")
    • Power Output: 3.7V to 7.4V
    • Voltage Range: 3.5V to 8.4V

     

     

    SKU: FUT-R7014SB
    €199.90
    inc. VAT

  • Futaba R7018SB S.Bus/2 18Ch FASSTest Telemetry Receiver

    Futaba R7018SB S.Bus/2 18Ch FASSTest Telemetry Receiver

    This is the Futaba 2.4GHz (18ch/12ch mode) R7018SB 2.4GHz FASSTest
    Bidirectional Communication Receiver.

    FEATURES: Full range up to 18-channels PWM or SBus/SBus-2 set up for all types and sizes of aircraft models including airplanes, gliders and multi-rotor aircraft that are gasoline, electric or glow powered.
    Dual antenna diversity
    SBus/SBus-2 compatible ports
    Battery failsafe
    One year limiterd warranty through Hobby Services beginning at date of purchase

    INCLUDES: R7018SB Receiver
    On/Off Switch Harness
    Two Female Ultra T-Plugs
    Heat Shrink Tubing
    Screwdriver

    SPECS:    Power Requirements: 6.0V to 7.4V (Voltage Range: 4.8 to 8.4V)
    Extra Voltage Port: 0~70V DC
    Resolution: 2,048steps
    Size: 2.15x1.59x0.64in (54.6x40.4x16.3mm)
    Weight: 1.48oz (42g)
    Speed (Frame Rate): 6.3ms / 15ms FASSTest (12ch/18ch)
    7ms / 14ms FASST (High Speed/Normal)

     

    SKU: R7018SB
    €239.00
    inc. VAT

     72HR STOCK
  • Futaba receiver R617FS 2,4 GHz FASST

    Futaba receiver R617FS 2,4 GHz FASST

    Ultra-small, lightweight seven-channel 2.4 GHz FASST receiver with full range.

    Diversity system constantly checks the signal level of both aerial inputs, and instantly switches to the stronger signal, with no interruption.

    "Pre-Vision": FASST receivers constantly scan the input signal, while special software technology automatically corrects any data errors which occur.
    Easy Link - simple "binding"
    The transmitter sends an identification code with more than 130 million possible combinations; this is stored in the receiver. The receiver only accepts signals from this one transmitter, regardless of other transmitters which log onto the 2.4 GHz band.

    Voltage: 4,8-6 Volts
    Channel spacing: 2048 kHz
    Weight: 9 g

    SKU: F0967
    €78.00
    inc. VAT

     72HR STOCK
  • Futaba RX R6106HF 2.4 GHz

    Futaba RX R6106HF 2.4 GHz

    6 Channel FASST-receiver 2.4 GHz with High Speed output for digital servos.

    A small, lightweight six-channel FASST receiver with end-mounted servo sockets. Switchable for analogue or digital servos, although the signal sent for digital servos is faster, giving a shorter reaction time. With just a 3 cm antenna, can be used for any type of model where there is no hull or chassis made from fibreglass reinforced plastic or metal to affect reception conditions.

     

    Not recommended for large-scale models and jets. Range: approx. 1000 m

     

    SKU: RobbeF0999
    €57.00
    inc. VAT

     72HR STOCK
  • Futaba RX R6106HFC 2.4 GHz

    Futaba RX R6106HFC 2.4 GHz

    6 Channel FASST-receiver 2.4 GHz with High Speed output for digital servos.

    A small, lightweight six-channel FASST receiver with end-mounted servo sockets. Switchable for analogue or digital servos, although the signal sent for digital servos is faster, giving a shorter reaction time. Usable in all sectors of modelling, the 14 cm antenna for this antenna can be positioned on the outside of hulls or chassis made of carbon-fibre reinforced plastic or metal. Not recommended for large-scale models and jets. Range: approx. 1000 m

    SKU: RobbeF1000
    €67.00
    inc. VAT

     72HR STOCK
  • Futaba S-Bus Receiver HV R6208SB

    Futaba S-Bus Receiver HV R6208SB

    The R6208SB for aircraft models is a new version 2.4Ghz S.Bus 8-channel Receiver from Futaba.

    Features:

    • Utilizes digital serial data communication technology to transmit control signals between the receiver and servos using S.Bus hubs and cables (available separately)
    • Easy programming with the SBC-1 Channel Setting Tool (FUTM4190), S-Bus receivers or PCLink software
    • SBD-1 decoder cables (not included) allow the use of existing analog and digital servos
    • Handles eight channels without S.Bus usage or as many as the available number of channels on transmitter with S.Bus use
    • Prevents mismatched servo/channel connections Full-range receiver with DAD (Dual Antenna Diversity) that can be used in any flight application

    Specification:

    • Power Requirement: 3.7V or 7.4V battery or regulated output from ESC (output capacity must meet usage condition)
    • Voltage Range: 3.5 8.4V
    • Dimensions: 0.98 x 1.86 x 0.56" (24.9 x 47.3 x 14.3mm)
    • Weight: 0.49oz (13.8g)

    Suitable for:

    • Futaba Transmitter with FASST Protocol, e.g. 8FG, 10CG, 12Z, 14MZ, 14SG, 18MZ
    SKU: F-R6208SB
    €170.90
    inc. VAT

     LOW STOCK
  • Graupner GR-16 Hott Receiver

    Graupner GR-16 Hott Receiver

       
    Graupner GR-16 Hott Receiver

    The GR-16 receiver can control up to 8 servos

    With the GRAUPNER HoTT 2.4 GHz technology, the receiver has a new hopping telemetry transmission high-frequency unit with state-of-the-art components and the latest software. A hardware antenna diversity system always switches to the better antenna signal and for transmission always uses the antenna that was last used for receiving. This ensures that the back channel data are always sent via the better-positioned antenna. Without additional sensor systems, the parameters receiver voltage and temperature, as well as signal strength are transmitted.

    The use of up to 75 channels ensures extreme operating reliability and immunity to external interference.
    The broad reception voltage range of 3.6 V - 8.4 V (functional to 2.5 V) ensures full functionality even when voltage fluctuates.
    Two LEDs signal operating status.
    The sizes and weights have been reduced.
    Receiver input sensitivity and thus the range have been increased further.
    Servo connections in the front panel.
    Failsafe, hold, OFF, and standard (channel 1 failsafe; all others hold) programmable.

    Functions with SMART-BOX

    • 3 mixers programmable
    • Linear, degressive, and exponential programming of servo curves
    • Sum signal programmable on channel 12 output
    • Limitation and reversal of servo travels also possible in receiver
    • Failsafe, hold, and OFF programmable individually for the servo channels
    • Warning thresholds programmable for undervoltage, excess temperature, and low temperature
    • Servo test function

    Specification

    • Dimensions (LxWxH) 46 x 21 x 14 mm
    • Frequency 2400 ... 2483.5 MHz
    • Modulation 2.4 GHz FHSS
    • All-up weight, approx. 12 g
    • Range approx. 4000 m
    • Temperature range - 15...+70 °C
    • Aerial length 2 x Draht 145 (Antenne 30) mm
    • Operating voltage (2,5) 3,6 ... 8,4 V
    • Charging rate 70 mA
    SKU: GR-33508
    €76.90
    inc. VAT

  • Jeti Central Box 200 Power Distribution Unit with Magnetic Switch

    Jeti Central Box 200 Power Distribution Unit with Magnetic Switch

    The Central Box 200 is a switchboard designed for the complete management of servos in a model with an emphasis on safety. The Central Box has a unique design that provides overload protection at each servo output. The Central Box can manage up to two batteries and fully supports the Jeti EX telemetry system. Up to two receivers with serial (PPM, EX Bus) output as well as two power batteries can be connected at the same time to the Central Box for complete Power & RF signal redundancy.

    With Jeti Duplex 2.4GHz DC/DS transmitters, the full potential of the Central Box can be used, such as an easy way to wirelessly configure the Servo Outputs, EX Telemetry, Fail-Safe Setting or Fast Servo Response.

    Included:

    • Jeti Central Box 200
    • Magnetic Switch
    • Magnetic Key

    JetiBox Configuration
    The JetiBox monitor/programmer can be used for parameter setting and retrieving data. After connecting to the Central Box (Ext1), a startup screen appears that contains identification of the device in the first line of the JetiBox display.

    Power Supply
    The power batteries are connected to the Central Box using MPX connectors. The Central Box allows two batteries to be connected. During use, the power is actually supplied from the battery with the higher voltage. If the voltage is the same, the power can be used from both batteries at the same time. When the voltage of the batteries is different, the power is not shared and each pack is isolated from the other. This allows you to use batteries of different capacity, number of cells and chemistry type. If the power for the Central Box is provided only from one battery, it can be connected via battery (BATT1) Input.

    Magnetic Switch (Included)
    The magnetic switch is used to turn the Central Box ON/OFF and is connected to a separate slot labeled "Switch". To turn on the Central Box using the magnetic switch it is necessary to hold the supplied magnet (key) to the target so that the key and the target on the magnetic switch are properly oriented.


    Features:

    • Control Management with Configurable Servo Output
    • Power Distribution with Two Independent Inputs
    • Firmware Updatable via Jeti USB Adapter
    • Jeti Duplex EX Bus or PPM Compatible
    • Wirelessly Programmable Using DC/DS Tx Device Explorer
    • Independent Receiver Signal Inputs (SAT1, SAT2)
    • Up to 15x Servo Outputs with Overload Protection
    • Up to 3x Telemetry Sensors Inputs (Ext1, Ext/14, Ext/15)
    • Input for Included Magnetic or Optional Wireless Switch
    • Input Voltage: 3.5-15V
    • Output Current: 2x 10A Continues/90A Peak
    • Dimensions/Weight: 62mm x 38mm x 16mm/30g
    SKU: J-CB-200
    €189.90
    inc. VAT

     72HR STOCK
  • Jeti Central Box 400 with magnetic key

    Jeti Central Box 400 with magnetic key

    Jeti Central Box 400 with magnetic key

    The Central Box 400 is a switchboard designed for the complete management of servos in large to giant models with an emphasis on safety. The Central Box 400 has a unique design that provides overload protection at each servo output. An independent, very powerful BEC (battery eliminator circuit) for each battery input makes the Central Box an optimal solution to connect up to 24 servos. The Central Box 400 can manage the batteries and fully supports the JETI EX telemetry system. Up to two receivers with serial (PPM, EX Bus, UDI) output can be connected to the Central Box 400. With a JETI DC/DS transmitter, the full potential of the Central Box can be used, such as easy configuration of the Central Box, EX telemetry, and very fast servo response.

    Central Box 400 supports up to 24 protected servo outputs, two battery inputs with voltage regulators and incorporates  possibility to connect an RC or magnetic switch.

    Attributes:

    • Two independent high-powered BEC´s for voltage stabilization of servos
    • Overload protection on each channel
    • Overload protection on Rx, Ext, and Switch outputs
    • Possibility to connect up to 2 receivers with serial interface (PPM, EX Bus, UDI)
    • Built-in Expander function for up to 4 sensors
    • Input for magnetic switch or RC switch
    • MPX battery input connectors: 2x
    • Stabilized voltage output via a pair of MPX connectors
    • 100Hz mode of servo outputs (10ms period)
    • Supports EX telemetry (voltage, current, capacity, and temperature measurement, overload indication, ...)
    • Easy settings changes via DC/DS transmitter
    • Internal memory for storage of telemetry data
    • USB connectivity for connection to PC
    • Easy settings changes via DC/DS transmitter
    • Firmware updatable
    • Suitable for use with high voltage (HV) servos
    • Robust metal construction with mounting holes
    • LED status indication
    • Each output is individually configurable (channel assignment, trim, reverse, ATV)

    Specication:

    • Weight [g]     270
    • Dimensions [mm]     131 x 88 x 19
    • Sustained current [A]     30
    • Number of channels     32
    • Telemetry     Yes
    • Operational temperature [°C]     -20 ... 75
    • Compatible protocols     EX Bus, PPM
    • Supply Voltage [V]     6 ... 17
    • Satellite receiver support     Yes
    • Batteries NiXX     6 ... 12
    • Batteries LiXX     2 ... 4
    • Voltage BEC [V]     5 ... 8
    • Idle current [µA]     60
    • Number of battery inputs     2
    • Voltage stabilization     Yes
    • Peak current (2s) [A]     230
    SKU: J-CB-400
    €599.00
    inc. VAT

     72HR STOCK
  • Jeti Central Box 400 with two satellite receivers Rsat 2 and with RC Switch

    Jeti Central Box 400 with two satellite receivers Rsat 2 and with RC Switch

    Jeti Central Box 400 with two satellite receivers Rsat 2 and with RC Switch

    The Central Box 400 is a switchboard designed for the complete management of servos in large to giant models with an emphasis on safety. The Central Box 400 has a unique design that provides overload protection at each servo output. An independent, very powerful BEC (battery eliminator circuit) for each battery input makes the Central Box an optimal solution to connect up to 24 servos. The Central Box 400 can manage the batteries and fully supports the JETI EX telemetry system. Up to two receivers with serial (PPM, EX Bus, UDI) output can be connected to the Central Box 400. With a JETI DC/DS transmitter, the full potential of the Central Box can be used, such as easy configuration of the Central Box, EX telemetry, and very fast servo response.

    Central Box 400 supports up to 24 protected servo outputs, two battery inputs with voltage regulators and incorporates  possibility to connect an RC or magnetic switch.

    Attributes:

    • Two independent high-powered BEC´s for voltage stabilization of servos
    • Overload protection on each channel
    • Overload protection on Rx, Ext, and Switch outputs
    • Possibility to connect up to 2 receivers with serial interface (PPM, EX Bus, UDI)
    • Built-in Expander function for up to 4 sensors
    • Input for magnetic switch or RC switch
    • MPX battery input connectors: 2x
    • Stabilized voltage output via a pair of MPX connectors
    • 100Hz mode of servo outputs (10ms period)
    • Supports EX telemetry (voltage, current, capacity, and temperature measurement, overload indication, ...)
    • Easy settings changes via DC/DS transmitter
    • Internal memory for storage of telemetry data
    • USB connectivity for connection to PC
    • Easy settings changes via DC/DS transmitter
    • Firmware updatable
    • Suitable for use with high voltage (HV) servos
    • Robust metal construction with mounting holes
    • LED status indication
    • Each output is individually configurable (channel assignment, trim, reverse, ATV)

    Specication:

    • Weight [g]     270
    • Dimensions [mm]     131 x 88 x 19
    • Sustained current [A]     30
    • Number of channels     32
    • Telemetry     Yes
    • Operational temperature [°C]     -20 ... 75
    • Compatible protocols     EX Bus, PPM
    • Supply Voltage [V]     6 ... 17
    • Satellite receiver support     Yes
    • Batteries NiXX     6 ... 12
    • Batteries LiXX     2 ... 4
    • Voltage BEC [V]     5 ... 8
    • Idle current [µA]     60
    • Number of battery inputs     2
    • Voltage stabilization     Yes
    • Peak current (2s) [A]     230
    SKU: J-CB-400-RS-RCSW
    €699.00
    inc. VAT

     72HR STOCK
  • Jeti Central Box CB100

    Jeti Central Box CB100

    JETI Central Box CB100

    The Central Box 100 is a switchboard designed for the complete management of servos in a model with on emphasis on safety.
    The Central Box has a unique design did Provides overload protection at each servo output.
    The Central Box can manage a single battery and fully supports the Jeti EX telemetry system. Up to two receivers with serial (PPM, EX Bus) output can be connected to the Central Box. With JETI DC / DS transmitter, the full potential of the Central Box kann used, examined as an easy way to configure the Central Box, EX telemetry, and very fast servo response.
    Central Box 100 supports up to 8 protected servo outputs and a single battery input.

    Attributes:

    • Overload protection on each channel
    • Possibility to connect up to 2 receivers with serial interface (PPM, EX bus)
    • Built-in expander function for up to 3 sensors
    • MPX battery input connectors: 1x
    • 100Hz mode of servo outputs (10ms period)
    • Supports EX telemetry (voltage, current, capacity, and temperature measurement, overload indication, ...)
    • Easy settings changes via DC / DS transmitter
    • Firmware updates by user
    • Suitable for use with high voltage (HV) servos
    • Compact size for easy installation
    • Each output is Individually configurable (channel assignment, trim, reverse, A TV)

     

    SKU: J-CB-100
    €119.90
    inc. VAT

     72HR STOCK
  • Jeti Central Box CB200 + 2 DR Sat2

    Jeti Central Box CB200 + 2 DR Sat2

    JETI Central Box CB200 + 2 DR Sat2

    The Central Box 200 is a switchboard designed for the complete management of servos in a model with on emphasis on safety.
    The Central Box has a unique design did Provides overload protection at each servo output.
    The Central Box can manage two batteries and fully supports the Jeti EX telemetry system. Up to two receivers with serial (PPM, EX Bus) output can be connected to the Central Box. With JETI DC / DS transmitter, the full potential of the Central Box kann used, examined as an easy way to configure the Central Box, EX telemetry, and very fast servo response.

    Central Box 200 supports up to 15 protected power outputs, two battery inputs and Incorporates Possibility to connect to RC or magnetic switch.

    Details:

    • Overload protection on each channel
    • Possibility to connect up to 2 receivers with serial interface (PPM, EX bus)
    • Built-in expander function for up to 3 sensors
    • Input for magnetic switch or RC switch
    • MPX battery input connectors: 2x
    • 100Hz mode of servo outputs (10ms period)
    • Supports EX telemetry (voltage, current, capacity, and temperature measurement, overload indication, ...)
    • Easy settings changes via DC / DS transmitter
    • Firmware updates by user
    • Suitable for use with high voltage (HV) servos
    • Compact size for easy installation
    • Each output is Individually configurable (channel assignment, trim, reverse, ATV)
    SKU: J-CB-200-RS
    €259.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex 2,4 GHz Receiver REX6

    Jeti Duplex 2,4 GHz Receiver REX6

    Jeti 6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

    Additional features:

    • PPM input
    • PPM output
    • Integrated expander for EX & EX Bus devices
    • UDI digital output

    JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
    The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
    The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers. For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
    The REX receivers are fully compatible with the previous generation of the Duplex equipment.

    Specification:

    • Weight [g] 11
    • Dimensions [mm]    38 x 25 x 11
    • Number of channels 6
    • Telemetry Yes
    • Operational temperature [°C]     -10 ... 85
    • Compatible protocols     DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm] 2 x 100
    • Supply Voltage [V] 3,5 - 8,4
    • Average Current [mA] 75
    • Satellite receiver support Yes
    • Output Power [dBm] 15
    • Receiver Sensitivity [dBm] -106
       
    SKU: JDEX-RR6
    €72.90
    inc. VAT

     LOW STOCK
  • Jeti Duplex 2,4 GHz Receiver REX7

    Jeti Duplex 2,4 GHz Receiver REX7

    Jeti 7 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions.

    Additional features:

    • PPM input
    • PPM output
    • Integrated expander for EX & EX Bus devices
    • UDI digital output

    JETI Duplex receivers are designated for use with the DC/DS transmitters or the JETI transmitter modules in the 2.4 GHz frequency band.
    The receivers support online updates so that everyone is able to install the latest software versions. From the very beginning bidirectional transmission has been a distinctive feature of the Duplex system, this not only handles telemetry data, but it also helps to ensure secure primarily transmission safety between the transmitter and receiver.
    The Duplex EX telemetry system uses an open protocol. This gives the advantage of compatibility with a large number of telemetry sensors from both JETI model and third party producers. For the display of telemetry data you can use purposely designed equipment like the JETIBOX profi and DC/DS transmitters or you can display the data on PCs.
    The REX receivers are fully compatible with the previous generation of the Duplex equipment.

    Specification:

    • Weight [g] 13
    • Dimensions [mm]    42 x 28 x 11
    • Number of channels 7
    • Telemetry Yes
    • Operational temperature [°C]     -10 ... 85
    • Compatible protocols     DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm] 2 x 100
    • Supply Voltage [V] 3,5 - 8,4
    • Average Current [mA] 75
    • Satellite receiver support Yes
    • Output Power [dBm] 15
    • Receiver Sensitivity [dBm] -106
    SKU: JDEX-RR7
    €79.90
    inc. VAT

     LOW STOCK
  • Jeti Duplex 2.4EX R18 Receiver

    Jeti Duplex 2.4EX R18 Receiver

     Jeti Duplex 2.4EX R18 receiver including RSat2 satellite receiver.

    Power can be supplied via the built-in MPX connector, which is compatible with the Jeti Max BEC 2, or via JR/UNI connectors. The power supply voltage required is 3.2-8.4V, but please note that this voltage is not regulated, so please ensure the input voltage is regulated appropriately according to your servo specification.

    The R18 includes a single RSAT2 satellite receiver with dual antennae, which should be operated in clone mode with the PPM output mode of the satellite set to 'DIRECT' and the PPM input mode of the R18 set to PPM Input on your chosen satellite channel.

    As with all Jeti Duplex 2.4GHz receivers, an audible alert can be configured so that the Duplex transmitter module emits an alarm, should the receiver supply voltage drop below a preset level. This is configurable by connecting the Jeti Box to the Tx module and this particular feature requires no additional sensors.

    Complete with bind-plug and MPX plug with two pieces of heatshrink.
    For a stable and reliable power source, we recommend the Max BEC range of voltage regulators. Alternatively you may wish to use two A123 LiFePO4 batteries, depending on your power requirements.

    Technical Details for Jeti Duplex 2.4EX R18 Receiver

    • Dimensions (mm)    62x38x16
    • Antennae Count    2
    • Antennae Length    400.00mm (15.75")
    • Channel Outputs    18
    • Temperature Range min. (°C)    -10
    • Jeti Box Compatible (JBC)    Yes
    • Temperature Range max. (°C)    85
    • Supply Voltage min.    3.2V
    • Supply Voltage max.    8.4V
    • Average Current (mA)    40
    • Transmission of Telemetric Data    Yes
    • Satellite receiver support    Yes
    • Power output (dBm)    20
    • Receiver Sensitivity (dBm)    -106
    • Weight    34.0g (1.2oz.)
    SKU: JDEX-R18
    €194.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex 2.4EX R9 channel full-range receiver

    Jeti Duplex 2.4EX R9 channel full-range receiver

    9 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors.

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    Specification

    • Weight [g]:  13
    • Dimensions [mm]: 48 x 23 x 10
    • Number of channels: 9
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 200
    • Supply Voltage [V]: 3,2 - 8,4
    • Average Current [mA]: 30
    • Satellite receiver support: Yes
    • Output Power [dBm]: 15
    • Receiver Sensitivity [dBm]: -106
    SKU: JDEX-R9
    €95.90
    inc. VAT

     LOW STOCK
  • Jeti DUPLEX 2.4EX RC Switch

    Jeti DUPLEX 2.4EX RC Switch

    JETI DUPLEX 2.4EX RC Switch

    RCSW - RC Switch is a wireless switch designed especially for JETI model products (BEC stabilizers, Central Box and other accessories) that increase the comfort of model control. RC Switch can be easily controlled using DC/DS transmitters and it can be simply used as a replacement of the magnetic key.

    Compatible devices: SBEC 40, DPS 40, SPS 20, DSM 10, Central Box 200, Central Box 400, Master Switch etc.

    Switching is indicated by a green LED that is visible through the opening on the side of the RC Switch.

    Setting the polarity of the switch is specific for each JETI model product, in the chart below there is a list of several supported devices and their RC Switch settings for DC and DS transmitters.

    SKU: JDEX-RCSW
    €72.90
    inc. VAT

     72HR STOCK
  • Jeti Duplex R6 EPC A40 Receiver

    Jeti Duplex R6 EPC A40 Receiver

    6 channel full-range receiver compatible with JETI EX & EX Bus protocols. Supports telemetry functions. Power supply can be provided by any of the servo JR connectors or by the external MPX connector.

    Antenna length: 40cm

    The DUPLEX EX line of receivers is intended for operation with DUPLEX Tx transmitter modules in the 2,4GHz band and are fully compatible with the previous version of the DUPLEX. Thanks to the fully digital and bidirectional communication between transmitter and receiver there arise completely new aspects in the model remote control branch. One of the most important advantages is the operation without crystal, moreover the low susceptibility towards interference, the high range up to the limit of visibility and the possibility to follow anytime the onboard state of the model and its functional parts.
    An additional satellite receiver RSat2 complements the receivers R9, R10, R11, R12, R14 and R18. This receiver is a full DUPLEX system receiver offering the complete functional spectrum of the system. Instead of classical servo pulses the output of the RSat2 receiver offers a PPM signal only. This PPM signal is furtheron processed by the receivers R9, R10, R11, R12, R14, R18 or by compatible RC equipment which requires a PPM signal at the input.

    DUPLEX System EX is fully compatible with the previous version of the DUPLEX.

    • Weight [g]: 11
    • Dimensions [mm]: 45 x 24 x 12
    • Number of channels:6
    • Telemetry: Yes
    • Operational temperature [°C]: -10 ... 85
    • Compatible protocols: DUPLEX 2.4GHz EX, EX Bus
    • Antenna Length [mm]: 2 x 400
    • Supply Voltage [V]: 3,2 - 8,4
    • Average Current [mA]:40
    • Satellite receiver support: No
    • Output Power: 15 dBm
    • Receiver Sensitivity: -106 dBm
    SKU: JDEX-R6EPCA40
    €77.90
    inc. VAT

     LOW STOCK
  • Jeti Duplex R7 Nano Receiver

    Jeti Duplex R7 Nano Receiver

    JETI Duplex R7 Nano Receiver Weight [g] 1 (2) Dimensions [mm] 30 x 18 x 5 Number of channels 7 Telemetry Yes Operational temperature [°C] -10 ... 85 Compatible protocols DUPLEX 2.4GHz EX, EX Bus Antenna Length [mm] 1 x 32 Supply Voltage [V] 3,2 - 8,4 Average Current [mA] 30 Satellite receiver support No Output Power [dBm] 6 Receiver Sensitivity [dBm] -98

    SKU: JDEX-R7N
    €62.90
    inc. VAT

     IN STOCK

Manufacturers

Back