Transport Vbar control case is the perfect addition to flightline equipment. Vbar Control Transmitter fits into the case like a hand into a custom made glove, with room for charge wart, accessory cords, neck strap, and wind meter. Black finish with VBar Logo.
Made from the same low friction polymer resin as our regular "Rocket" ball links but now in high visibility neon orange, green and yellow.
Suitable for use on 2.0 & 3 mm pushrods but EASILY can be re-drilled to suit up to a 3mm thread if required.
Norlam Standard length shank measuring 22mm from ball centre to the end and are suitable for fitting to 3/16" (4.76mm) control balls.
Shorter are 14mm* good for Servos for tail and other short applications
All-purpose grease supplied in practical jet-applicator; ideal for the modeller.
- friction and wear reduced five-fold
- extra safety margin
- suitable for plastic and metal
- useful life of parts extended up to 200%
- resistant to fuel and ageing
- temperature range -15°C to + 250°C
- Plastic and metal differentials
- wheel bearings
- needle roller bearings
The new Scorpion Lock Straps feature a revolutionary non-slip coating on the inside surface that securely locks your battery in place and prevents them from shifting, even during the most radical 3D aerobatic maneuvers. These large size straps are perfect for 500 to 700 class electric helicopters or larger RC Aircraft. The large size strap measures 1 inch wide by 12.5 inches long (25mm x 315mm), so they will fit around a 6-cell 5000mah battery pack. The straps feature a tough plastic buckle and a strong Velcro closure for maximum holding power and security. Each package contains 3 Scorpion Lock Straps.
a MUST, Peace-of-mind for pilots With 7 LEDs providing instant, accurate receiver battery voltage status, the VoltWatch is a super accessory for any modeler. Pilots simply mount the VoltWatch anywhere the 7 tiny status lights can be seen Selectable switch to choose 4.8 or 6.0v. Very lightweight unit can be mounted on the side of the fuselage Draws amazingly low current less than 10mA Plugs into any open receiver channel
Don't have the battery slip out while flying out of the switch or just lock in the servo extensions securely Clip for servo connector or extension lead joint, to prevent the connection breaking under outside force.
4 PCS in set
Don't have the battery slip out while flying out of the switch or just lock in the servo extensions securely
Clip for servo connector or extension lead joint, to prevent the connection breaking under outside force.
4 PCS in set
The robbe Sound module reproduces the distinctive sound of a multi-cylinder radial engine. This makes it suitable for use in electric-powered model aircraft such as the Air Beaver (robbe No. 2569), Fokker DR 1 (robbe No. 2572) and any other model of an aircraft powered by a radial engine. The sound generated by the module varies according to the motor speed. Motor speed information is fed to the module via the speed controller to which it is connected.
Installing the module and the loudspeaker calls for substantial manual modelling skills, as modifications may be required to the model's fuselage in order to install the loudspeaker correctly.
Input voltage: min. 8 - max. 18 V
Idle current: ≤ 10 mA
Operating current: 480 – 520 mA
Weight: approx. 170 g (loudspeaker, module, cable set)
Dimensions, module case: approx. 74.5 x 34.5 x 22 mm
Dimensions, loudspeaker: approx. 65 Ø x 28 mm.
65 mm wide-band loudspeaker with connecting leads and connector
Cable set with connectors for flight battery and receiver
Y-lead for receiver - speed controller or receiver - sound module connection
SPARTAN Gyro Metal plate
Gyros are sensitive to high frequency vibrations. The metal plate helps isolate these vibrations and not allow these vibrations to be transmitted to the Gyro. If your gyro was working fine and then suddenly started to drift try to find the source of this possible vibration.
We recommend to use the metal plate between the gyro pads.