With ergonomically-designed, comfortable pad helps to redistribute the weight of the radio load and improve body alignment thereby reducing neck an shoulder pan.
Also the pad adopts non-slip grip effectively reduce friction on the neck skin.
A quick & simply way to store your blades for transport. This universal blades caddy is made from laminated high density foam to protect your rotor tips whilst holding them securely. Will suit tailbooms ranging between 20 - 25mm
New, avaliable in 4 sizes, from Micro helis, till 90 size. The sizes are different, please choose as per your model size
Please choose from Product options
Don't have the battery slip out while flying out of the switch or just lock in the servo extensions securely
Clip for servo connector or extension lead joint, to prevent the connection breaking under outside force.
Flybar conus weight and stiffener.
Those conical adapters must be fitted on any Helicopter to balance the flybar.
The conus creates good and equal Load Sharing on the Flybar Area and will prevent the flybar to weaken and break as a result of vibrations.This is a "Must" part for any Helicopter.
Fit 4mm flybars , made from 7075 Alu , set of 2 pieces.
Connect the alarm between the servo and the receiver, i.e. act as a servo extension cord.
Turn on your TX. and you will hear 2 x beep sound.
Do not move any of the control stick on the TX or simply turn off the the TX. You will hear a continuous beep sound after 1 minute. It will stop once u turn on your TX or move the control stick.
If you ignore the continuous beep sound for around 2minutes, the beep sound will change the a louder V sound.
You need to disconnect the alarm from the receiver in order to switch of the alarm.
Specifications:
RC Radio Control Lost Finder Tracker
Suitable Controller: All PPM/FM, PCM/FM, AM Tx/Rx
Loud >85dB alarm gets your attention
Two alarm tones pattern
Works with AM/FM PPM or FM/PCM R/C systems
Plugs into any standard servo channel
Operating Voltage(v) : 4-6v
Current Drain(mA) : 1-35
Can be heard in 50 meter distance
How to set up
1. Connect the lost alarm between the servo (the one which runs when flying) and the receiver, i.e. act as a servo extension cord
2. Turn on your transmitter
3. Turn on your receiver then you will hear two beep sound
4. To test if it is functioning:
Do not move any of the control stick on the transmitter for 1 min. or simply turn it off
You will hear a continuous beep sound after 1 minute
If you ignore the continuous beep sound for around 2 minutes, the beep sound will change to a louder V sound
It will stop once you move the control stick or power off the receiver
5. If you cannot find you plane, do not move the control stick or turn off your transmitter for 1 min for the alarm sound
6. By the tracking sound, you will be able to locate your RC plane / Helicopter
7. To stop the alarm : Move the control stick or Power off the receiver
Can be connected to any kinds of servo
Should be connected to the servo that runs when flying
Made from the same low friction polymer resin as our regular "Rocket" ball links but now in high visibility neon orange, green and yellow.
Suitable for use on 2.0 & 3 mm pushrods but EASILY can be re-drilled to suit up to a 3mm thread if required.
Norlam Standard length shank measuring 22mm from ball centre to the end and are suitable for fitting to 3/16" (4.76mm) control balls.
Shorter are 14mm* good for Servos for tail and other short applications
RC ball links are made from high strength low friction "DELRIN" nylon and suitable for use on 2.0 & 2.3mmpushrods as standard but can also be drilled out to suit 2.5mm and even 3mm control rods.
Pack of 10. Avaliable in neon Green , Neon pink and Neon Yellow colors
a MUST, Peace-of-mind for pilots With 7 LEDs providing instant, accurate receiver battery voltage status, the VoltWatch is a super accessory for any modeler.
Pilots simply mount the VoltWatch anywhere the 7 tiny status lights can be seen Selectable switch to choose 4.8 or 6.0v.
Very lightweight unit can be mounted on the side of the fuselage
Draws amazingly low current less than 10mA
Plugs into any open receiver channel
