PDB -Filters-OSD

Products


  • CC3D Flight Controller Mini Power Distribution Board PCB

    CC3D Flight Controller Mini Power Distribution Board PCB

    Power Distribution  Board for CC3D flight controller

    Features:

    • Mini size,Light weight.(only 3.5g)
    • The same size  and hole location as CC3D
    • Integrated 2 switch to control LED and FPV equipments

    Package included:

    1 x CC3D flight controller  Distribution Power Board

    SKU: SKY2015
    €6.00
    inc. VAT

     IN STOCK
  • DJI IOSD (ON SCREEN DISPLAY) MARK II

    DJI IOSD (ON SCREEN DISPLAY) MARK II

    The iOSD Mark II On Screen Display is for the DJI Wookong M AutoPilot and Ace One series AutoPilots. The iOSD On Screen Display enables the pilot to monitor the real-time flight data from the Wookong M WKM or Ace One Autopilot systems while in flight using First Person View (FPV).

    The DJI iOSD MARK II can record the flight log, which will help you to record the input and output information of every channel, GPS signal, power voltage, home distance and height, etc. (The current iOSD on the market will have flight log function after firmware upgrade.)

    The DJI iOSD will allow you to view the following information:

    • Voltage
    • Vertical velocity
    • Horizontal velocity
    • Height
    • Distance from home point
    • Horizontal Altitude
    • GPS satellite number

    The iOSD is a multifunctional integrated on screen display module which also has a built-in BEC module that supports 3s-6s LiPo batteries (11-26 volts), when used with the Wookong M or Ace One professional autopilot systems, it delivers a total solution for aerial photography with key information clearly displayed around the outside of the screen.

    The DJI Innovations iOSD only supports the Wookong M AutoPilot and Ace One systems at this time. The iOSD supports two video input sources, one of which can be selected by the R/C transmitter and switched remotely. It can also change the wireless the transmission channel using the wireless video transmission module by DJI. The iOSD can be upgrade in the future by firmware updates.

    SKU: DJI_IOSD_MKII
    €195.00
    inc. VAT

     LOW STOCK
  • DJI iOSD Mini DJI

    DJI iOSD Mini DJI

    The Naza-M now supports iOSD Mini. This will undoubtedly give you a fantastic FPV flight performance. Depending upon DJI’s accumulation of historic and reliable information integration technology, the iOSD Mini can grab the most accurate first-hand flight data information in the shortest possible time.

    Technical Specs:

    • Voltage: 6V
    • Working Temperature: -20℃~+60℃
    • Video Input/Output Mode: PAL/NTSC (automatically recognize)
    • Weight: 14g
    • Working Current (Typical Value): 180mA@6V
    SKU: DJI_IOSD_MINI
    €64.99
    inc. VAT

     LOW STOCK
  • Drone multicopter RTF LC-FILTER 3A, 2-4S

    Drone multicopter RTF LC-FILTER 3A, 2-4S

    Base off the  " "L-C Power Filter-1.7A"  this filter will Clean up and dirty power supply. This is a compact and effective LC filter designed to clean a noisy DC power supply. Perfect for sensitive FPV- and RC-components in a single battery setup. The filter has properties to reduce the effects of interference radiated through the air and noise conducted via the power wires. One advantage of this filter is that both the negative and positive leads are filtered (common mode).


    Suitable for setups up to 16V and maximum 3A  load. Problems often occur on sensitive FPV video systems when long power leads (7cm+) are used, limited space for wiring, improperly filtered transmitters, noise from speed controller or switch mode DC-DC voltage converter, or most commonly a shared battery is used to minimize weight. The interference can result in video lines, banding, random drop-outs, and reduced transmission range. A low-pass LC-filter will help attenuation most of the high frequency power supply noise and interference.

    SKU: LCFILTER
    €7.00
    inc. VAT

     IN STOCK
  • Dual BEC Output 5V 12V Adjustable Voltage Distribution Board

    Dual BEC Output 5V 12V Adjustable Voltage Distribution Board

    Dual BEC Output 5V 12V Adjustable Voltage Distribution Board

    • 5V 12V Adjustable Voltage Dual BEC Output Board ESC Distribution Connection Board for FPV
    • Distribution board with two-way BEC output is made of thickened copper foil and turmeric processed on the surface and supporting 100A current.
    • Directly poweing a Brushless Gimbal, 5.8G TX & RX system or FPV camera from  12V BEC, while 5V BEC can provide power for Flight control
    • 1CH 12V output, 1CH adjustable, support 3-20V adjustable
    • Each BEC support 2A stabilized output

    Note: Before use BEC output port, please measure the real output voltage first, make sure it meet your requirements. Delivered as 5V output as default

    SKU: D-BEC-PDB
    €7.00
    inc. VAT

     IN STOCK
  • FOXEER PDB POWER BOARD 12V/5V DUAL UBEC 12V

    FOXEER PDB POWER BOARD 12V/5V DUAL UBEC 12V

    This power distribution board is specially designed for multirotors, It makes the wiring of your multirotor ESC's neater and more secure.
    This is the very latest version with a 2 BEC's fitted, one is a 12V the other is a variable 5v which is very handy.
    The latest CC3D power distribution board with dual BEC output 3A 5V and 12V
    The hole and size is same as CC3D flight control board Control switch with LED

    Input voltage 2-6S weight:5.1G
    Size:36*36 Pitch :30.5*30.5
    Only work with above 4S battery
    Package Include: 1 x power board

    SKU: MR1178
    €8.00
    inc. VAT

     IN STOCK
  • HUBOSD Eco X Type, w/STOSD8, Current Module, Dual BEC & XT60

    HUBOSD Eco X Type, w/STOSD8, Current Module, Dual BEC & XT60

    Matek HUBOSD Eco X Type with STOSD8 Current Module 5/12V Dual BEC and XT60 Plug

    The HUBOSD8 has been designed to provide the highest possible performance and reliability in a 46*36mm & 4 layers PCB. It is a multifunctional HUB with PDB, BEC 5V/2A &12V/500mA, Current sensor 140A, STOSD8. Especially made for the mini FPV Quad. The BEC 12V is linear regulator, no LC Filter needed. Built-in STOSD8 can support Plug & Play, no complicated settings needed.

    Specifications:

    • Input: 8~ 21V (3-5S LiPo)
    • PDB: 4x30A (Max.4x35A)
    • Regulated 5V and 12V outputs
    • Current Sensor 140A
    • Built-in STOSD8
    SKU: HUBOSD8-X
    €19.90
    inc. VAT

     IN STOCK
  • Linear Regulator 4S LiPo to 12V 300mA

    Linear Regulator 4S LiPo to 12V 300mA

    Linear Regulator 4S LiPo to 12V 300mA (1pc)

    • Suitable for FPV Camera
    • Compared with BEC12V, linear voltage regulator with low-ripple, does't interfere the image signal
    • Temp. 25℃, 16V input, 12V output 300mA, 5min, the highest measured temperature is 58℃
    • Can be connected with extra only one 12V 1.5W LED light.
    • If the 3S and 4S mixed, it support 3S battery too. Output voltage=3S voltage-1V, eg. the battery voltage is 12V, actual output is 11V, and the camera can work normally.

    Description:

    • Item Name: Linear Voltage Regulator
    • Input Voltage:13~17V, 4S LiPo
    • Output Voltage: 12V,  accuracy 2.5%
    • Output Current: Continuous 300mA
    • Size: 25*10*3mm
    • Weight: 1g
    SKU: LDO12
    €3.50
    inc. VAT

     IN STOCK
  • Matek Micro Power Distribution Board PDB w/ BEC 5V/12V 32X22mm

    Matek Micro Power Distribution Board PDB w/ BEC 5V/12V 32X22mm

    The Micro PDB has been engineered to provide the highest possible performance and reliability in a 32*22mm & 4 layers PCB. It distributes power from a battery pack to 4 ESCs, as well as providing dual synchronised & regulated DC outputs for powering Cameras, Servos, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc.

    It offers a very compact solution to achieve 2A continuous output current over a wide input supply range(3S to 5S LiPo).

    Features :

    • 2oz copper & 4-layers PCB
    • ESC & Battery solder tabs in pairs
    • 5V & 12V Output LED indicators & Short circuit tolerant
    • Micro size & lightweight

    Specification :

    • Input voltage range (3S-5S operation): 7 - 21V DC
    • Regulated 5V and 12V outputs
    • LED power indicators ( 5V & 12V outputs )
    • 4 ESC outputs

    ESC outputs :

    • Continuous current: 20A per output
    • Peak current (10 seconds/minute): 25A per output
    • BEC 5V output :
    • Designed for RC Receivers, Flight controllers, OSD, and Servos
    • DC/DC synchronous buck regulator
    • Voltage: 5.0 +/- 0.1VDC
    • Continuous current: 2 Amps (Max.2.5A 5s/minute)
    • Output Ripple: 40mV (VIn=16V, VOut=5V@2A load)
    • Short-circuit tolerant (5 seconds/minute)
    • BEC 12V output :
    • The battery should be 4S~5S LiPo (12.8~21V DC)
    • Standard output designed to power cameras and video transmitters,etc
    • DC/DC synchronous buck regulator, Efficiency is up to 96%
    • Voltage: 12.0 +/- 0.2VDC
    • Output Ripple: 20mV (VIn=16V, VOut=12V@2A Load)
    • Continuous current: 2 Amps (Max.2.5A 5s/minute)
    • Short-circuit tolerant (5 seconds/minute)

    BEC 12V @ 3S LiPo :

    • Output voltage= 3S LiPo voltage x 95% Physical:
    • Dimensions: 32 x 22 x 3 mm
    • Weight: 3.5g
    SKU: MPDB5V12V
    €8.90
    inc. VAT

     IN STOCK
  • Matek Mini Power Hub 5V/12V BEC Distribution Board PDB for FPV

    Matek Mini Power Hub 5V/12V BEC Distribution Board PDB for FPV

    The Mini Power Hub is engineered to provide the highest possible performance and reliability in 1 36*36mm & 4 layers PCB. The hub distributes power from a battery package to 4 ESCs, as well as providing two synchronised & regulated DC outputs for powering cameras, servos, video transmitters, LEDs etc. Batteries may range from 3S to 6S LiPo, and the BEC input is TVS protected
    The hub also features convenient solder bridge of various voltage for camera & video TX.

    Features :

    • 2oz copper & 4-layers PCB.
    • ESC & Battery solder tabs in pairs
    • Solder Bridges of various voltage for Camera & VTX.
    • 5V & 12V Output LED indicators & Short circuit tolerant

    Specification :

    • Input voltage range (3S-6S operation): 9 26VDC
    • Regulated 5V and 12V outputs
    • LED power indicators ( 5V & 12V outputs )
    • 4 ESC outputs
    • ESC outputs :
    • Continuous current: 20A per output
    • Peak current (10 seconds/minute): 25A per output

    BEC 5V output :

    • Designed for RC Receivers, Flight controllers, OSD, and Servos.
    • DC/DC synchronous buck regulator, Efficiency is up to 95%.
    • Voltage: 5.0 +/0.1VDC
    • Continuous current: 3 Amps
    • Short-circuit tolerant (10 seconds/minute)
    • LED (indicates voltage is in regulation)

    BEC 12V output :

    • The battery should be 4S~6S LiPo
    • Standard output designed to power cameras and video transmitters,etc.
    • Voltage: 12.0 +/0.2VDC
    • Continuous current: 2 Amps (Max.3A 10s/minute)
    • Short-circuit tolerant (10 seconds/minute)
    • LED (indicates voltage is in regulation)
    • CAM & VTX voltage bridge
    • 3S operation. choose “VCC” for 12V camera & 12V VTX, VCC=Battery Voltage.
    • 4~6S operation, choose “12” for 12V camera & 12V VTX
    • 3~6S operation, choose “5” for 5V camera
    • Video pass through from the “CAM” pad to the “VTX” pad

    Physical :

    • Dimensions: 36 x 36mm
    • Weight: 6g
    • Mounting holes 30.5mm square spacing
    SKU: HUB5V12V
    €7.90
    inc. VAT

     IN STOCK
  • Matek PDB Mini 12V Power Distribution Board uBEC BEC FPV

    Matek PDB Mini 12V Power Distribution Board uBEC BEC FPV

    This PDB is special used on the FPV Quad copter with 3~4S LiPo.A small PDB board to connect your battery to your esc’s with a built in low drop regulator 12V for your FPV camera. Small and Light. Can power the 12V camera & 12V LED without ripple & noise.

    Generally the input voltage of FPV camera is 7~13V,When 4S LiPo is mounted, the linear regulator can power the 12V camera & 12V LED without ripple & noise.

    •     Size: 40*22mm PDB, 3g, Small & Light.
    •     Inbuilt 12V Linear regulator, Cont.500mA
    •     Mounting: 24mm /3mm

     

    SKU: PDB-LDO
    €4.00
    inc. VAT

     IN STOCK
  • MAVLink-OSD V1.1 On-Screen Display MinimOSD for AIOP APM Telemetry

    MAVLink-OSD V1.1 On-Screen Display MinimOSD for AIOP APM Telemetry

    This is a mini Arduino based on-screen display board. It’s tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as small as possible.

    It’s main components are an ATmega328P 8 bit microcontroller with an Arduino bootloader, and a MAX7456 monochrome on-screen display. Programming is done through an FTDI-compatible 6-pin cable.

    MinimOSD is companion On Screed Display (OSD) Board for APM. It reads all the MAVLink data in the APM telemetry stream and overlays it on the video stream if you’re using an on-board camera and wireless video transmitter. This is useful if you’re flying in First Person View (FPV) mode or don’t want to use a laptop at the field to see your telemetry data in the Mission Planner.ee your telemetry data in the Mission Planner.

    Features

        Two independent power and ground sections to isolate the OSD’s analog stage:
        A +5V section for the ATmega and the OSD’s digital stage, powered through the FTDI cable or other +5V source
        A regulated +5V section for the OSD’s analog stage, powered through the video in/out header and capable of handling up to +12V input.
        Solder jumpers are available to combine the two power and ground sections if desired.
        Supports APM2, APM2.5, APM2.6

    Technical Specifications

        ATmega328P with Arduino bootloader
        MAX7456 monochrome on-screen display chip.
        FTDI cable compatible pinout
        Standard 6-pin ISP header (Not Populated)
        Two independent power sections with an LED indicator on each
        Solder jumpers for combining the power sections
        +5V 500mA regulator for up to +12V supply input
        Solder jumper for PAL video option
        Exposed test points for HSYNC and LOS

    Package Includes

        1x Minim OSD v1.1 module with plastic casing
        A set of female to female cables

     

    SKU: MAVLink-OSD
    €18.00
    inc. VAT

     IN STOCK
  • Micro MinimOSD with MultiWii OSD

    Micro MinimOSD with MultiWii OSD

    The MinimOSD was engineered to bring users a very powerfull OSD. With all the features of the very popuar minimosd modded OSD but in a tiny 15x15MM size.

    Apart from the size, the only differenece is that it does NOT have the DC/DC converter this means less heat when powered off a flight controller. The micro MinimOSD is the same as the older MinimOSD hardware but has been modified to take advantage of custom firmware options. You can flash firmware that is MAVLink compatible for ArduCopter, or MultiWii Serial compatible for MultiWii and Baseflight/Cleanflight control boards. You can connect two batteries up to 4S so you can see the main flight battery voltage.  The second port will allow a separate FPV battery voltage on the display as well. There is also a pin for analog or digital PWM RSSI and a connection where you can attach a current sensor.

    Features:

    • All the same features as the original, around 1/3 of the size.
    • NO DC/DC converter. Power board via 5V DC.
    • FTDI cable compatible pinout
    • Two LED indicators
    • ATmega328P with Arduino bootloader
    • MAX7456 monochrome on-screen display
    • 15x15MM size!
    • Modifications for direct connection of two batteries (up to 4S)
    • Pad for an Analog or Digital PWM RSSI signal
    • Pad for the connection of a Current Sensor
    • ATmega328P with Arduino bootloader

     

    SKU: MICROMOSD
    €12.00
    inc. VAT

  • Mini PDB sky hero

    Mini PDB sky hero

    Mini PDB sky hero, Connector XT60 comes not soldered, for the option to have it on the pdb or connected with the wire

    SKU: SKH04-OB1
    €6.50
    inc. VAT

     IN STOCK
  • Multicopter Power Distribution Board PDB (With OnBoard 3-12V Adjustable BEC)

    Multicopter Power Distribution Board PDB (With OnBoard 3-12V Adjustable BEC)

    5V-12V Adjustable Voltage BEC Output ESC Distribution Connection Board

    This board is designed with dual channel BEC output distribution, with turmeric processing in surface, can support max. 100A current. The high effeciency dual channel BEC circuit structure can support 6S Lipo battery input. One channel is 12V output, while another channel is adjustable, support 3-12V. Each BEC supports 2A stable output (can also reach 3A stable output with another heat sink)!

    What are you waiting for? 12V BEC + 5V BEC + ESC distribution board, wherein the 12V BEC can directly offer power to brushless gimbal, 5.8G graphic transmission or FPV cameras and 5V BEC can offer power to open source brushless controller and Gopro, etc.

    *Note: Before use the BEC output, please measure the real output voltage to make sure it meets your requirment. The default BEC output is 5V.

    Max current:up to 100A
    Standard 50mm * 50mm board size
    Weight : 9gr

    SKU: PCD-5252125
    €9.00
    inc. VAT

     IN STOCK
  • Multicopter Power distribution Board PDB 100Amp

    Multicopter Power distribution Board PDB 100Amp

    Multicopter Power distribution Board PDB 100Amp

    Allows connection up to 16 ESC to this Board

    SKU: TRIT8
    €9.00
    inc. VAT

     IN STOCK
  • OSD board with cable for FPV-700 camera

    OSD board with cable for FPV-700 camera

    OSD board with cable for FPV-700 camera, This board allow you to connect to the camera and set up basic settings.

    SKU: CM001-1
    €9.90
    inc. VAT

     IN STOCK
  • PDB for Race quads, Nighthawk X-Series

    PDB for Race quads, Nighthawk X-Series

    Built-In 5V and 12V regulators supply ample amount of clean, filtered power to the electronics.
    ESC Signal pads allow clean and efficient builds with less wire.
    Programmable RGB LEDs let user play with endless colours and features through the flight controller using Cleanflight-Configurator.
    XT60 connector is directly mounted onto the PDB (further reducing weight by eliminating heavy wires as well as risk of cutting power leads).
    Dedicated signal pads are aligned with the flight controller to allow clean connections.

    SKU: PDBNH
    €5.90
    inc. VAT

     IN STOCK
  • Power 5 in 1 V3 Distribution Board PDB LED Control 5V BEC, Voltage Alarm Tracker for FPV Multicopter

    Power 5 in 1 V3 Distribution Board PDB LED Control 5V BEC, Voltage Alarm Tracker for FPV Multicopter

    Matek Power 5 in 1 V3 Distribution Board PDB LED Control 5V BEC, Voltage Alarm Tracker for FPV Multicopter

    The 5in1V3 has been engineered to provide the highest possible performance and reliability in a 46*36mm & 4 layers PCB.
    It is a 5in1 HUB with Power Distribution Board, BEC 5V/3A &12V/500mA, LED Light Controller, Lost Plane Finder & Low Voltage Alarm functions.
    It is specially made for the Multi-Rotors, mini FPV Quad. Built-in 5V BEC can be connected to receiver or flight controller with Aux pins directly.
    simplify wiring. The BEC 12V can be used to power the Camera, Video Transmitters,ect. Inbuilt 5V LED light controller, three flash modes can be choosed with the toggle switch of transmiter.
    And the buzzer can also be triggered with the toggle switch, which can help you find the models in tall grass or trees.
    The 5in1 also acts as a battery voltage monitor.
    Once voltage gets below the threshold you set, the buzzer & LED light will remind you.

    Specifications:

    • Input voltage range (3S-6S operation): 9 – 26VDC
    • 1 Battery input & 4 ESC outputs
    • Regulated 5V and 12V outputs
    • LED power indicators ( 5V & 12V outputs )
    • 4 pairs 5V LED light pads
    • Low voltage setting value indicators

    Includes:

    • 1 x Matek LED & POWER HUB 5in1 V3 Board
    • 1 x cable (100mm)
    • 4 x stand-off (10mm)
    • 4 x stand-off (5mm)
    • 4 x nut
    • 4 x screw
    • Dimensions:46x36x6mm,
    • Weight: 9g
    • Mounting holes 30.5mm square spacing

    Features:

    • Built-in 5 functions, small size & light weight
    • 2oz copper & 4-layers PCB.
    • ESC & Battery solder tabs in pairs
    • BEC 5V & 12V Output LED indicators
    • TVS input protection
    SKU: PDB5IN1-V3
    €13.90
    inc. VAT

     IN STOCK
  • Power Distribution Board 12ESC (PDB) with LED 100A

    Power Distribution Board 12ESC (PDB) with LED 100A

    This power distribution board is used to make your multicopter installation neater and safer.  With support for up to 100A, and 8 ESC this PDB can be used on almost any multicopter. In addition to providing simple power distribution for up to 8 ESC's this board also includes two built in voltage regulators (5V output and 12V output) that you can use to power your electronics/, LED's or FPV gear on your multicopter. Other great features include LED's built onto the board.

    Please note that this PDB does not come with any cables, you will need to solder your ESC, and battery connector to this board.
    PDB Specification

    •   Max ESC number - 12
    •   Working Current - 100A Max
    •   Outer Diameter - 77mm
    •   Inner Diameter - 40mm
    •   Max input voltage - 6S
    •   5V Regulated output (built in voltage regulator)
    •   12V Regulated output (built in voltage regulator)
    SKU: SKU48602
    €18.00
    inc. VAT

  • Power Distribution Board 320 amps

    Power Distribution Board 320 amps

    Power Distribution Board 320 amps, with 8 connections, for any model/quad copter.

    SPECIFICATIONS

    • Allows Up to 8 ESC/Motor connections
    • Current : 260A (Continuous), 320A (Peak)
    • 2 Stage layout with 2oz (70um) Copper Dual PCB.
    • Body Mounting 64mm

     

    Included:

    • 1 Black PDB plate, 1 White PDB
    • Bullet connectors x 16
    • Plastic supports/Mounting spacers x 4
    • Weight : 53g
    • Size : 100mm x 100mm
    SKU: PDB320
    €28.00
    inc. VAT

  • Power Distribution Board and Dual UBEC 10-20V, 120 AMPS

    Power Distribution Board and Dual UBEC 10-20V, 120 AMPS

    Power distribution board (PDB) is a 3-in-1 device that simplifies even the most complicated multirotor builds.

    The PDB has two built in UBEC’s; one set at 5 volts, handy for a flight controller or receiver and the other adjustable from 10-20 volts, perfect for powering lighting, servos and other gear. The board even features integrated LED’s that illuminate when you plug a battery in.

    With this board, even if you’re building an octocopter you won't be stuck for connections. There are 12 positive/negative pads (8 large, 4 small) for power distribution and also four outputs for each UBEC. Best still, unlike many inferior boards this PDB can handle high Amps thanks to its 4oz copper construction, up to 120A to be precise. The UBEC's are just as impressive being rated for 6s high voltage setups. Finally when it comes to mounting the board, the standard M3 45mm spaced holes make it easy to mount to most multirotor frames.

    Please note that basic soldering skills are required to construct this board - see the assembly instructions for further information and the required equipment.

    SKU: DY-PDB
    €19.90
    inc. VAT

     IN STOCK
  • Power Distribution Board PDB PCB 5V & 12V BEC 3A

    Power Distribution Board PDB PCB 5V & 12V BEC 3A

    Power Distribution Board PDB, integrated 5V & 12V BEC 3A for FPV racers. Fit same size as CC3D dimensions support

    • Using ehhanced over-current design, max. current 100A.
    • Using imported step-down power switch IC design, efficiency of BEC is higher than 92%.
    • Low noise design, closed magnetic high power inductance to reduce electromagnetic interference.
    • BEC has over-heat protection and output short-circuit protection functions.

    Specifications:

    • Input Voltage: 2-6S (7.4-26V)
    • Output Current: Max. 100A
    • BEC1 Output: 5V/3A
    • BEC2 Output: 12V/2.5A, Max. 3A
    • Quiescent Current: <10mA
    • Dimensions: 36*36mm
    • Installation Dimensions: 30.5*30.5mm
    • Weight: Approx. 6.5g

     

    SKU: PDB-BEC
    €7.00
    inc. VAT

     IN STOCK
  • RadioLink OSD telemetry sensor PRM-02

    RadioLink OSD telemetry sensor PRM-02

    OSD Telemetry module transmits the data from the flight controller and shows the data of SPEED, RISE, THRO, VOLT, LATI, LONG, ALT, GPS, RSSI, MODE, YAW, ROLL, PITC, DIST in the display screen of AT9 or AT10.

    Introduction:
    1. Please upgrade your AT9 firmware to V1.2.6(OSD).(1)AT10 firmware to V1.0.6(OSD).
    2. So far, this OSD telemetry module is compatible with PIX and APM.
    3. OSD telemetry module can work with both R9D and R10D.

    Attention :

    1.No output if USB connect flight-controller and computer.

    2.No VOLT information if use UBEC, have to offer electricity for flight-controller by volt ammeter.

    3.Have to short-circuit the MUX-TXO/OSD of APM when connect PRM-02(OSD) to APM.

    Size: 33*15mm

    Weight: 6g (including connector)

    SKU: PRM-02
    €18.00
    inc. VAT

     IN STOCK

Manufacturers

Back