Mikado Logo 800 XXTREME

Products


  • SAVÖX HIGH VOLTAGE BRUSHLESS DIGITAL TAIL SERVO 0.048/138.9 @7.4V

    SAVÖX HIGH VOLTAGE BRUSHLESS DIGITAL TAIL SERVO 0.048/138.9 @7.4V

    SAVÖX HIGH VOLTAGE BRUSHLESS DIGITAL TAIL SERVO 0.048/138.9 @7.4V

    The SB2283MG is an ultra high speed servo running at .048sec transit @ 7.4V.
    This servo is a great choice for your heli gyro.
    Combines leading edge technology with super high 12 bit (4096) resolution and titanium gears.
    Super light-weight.
    Brushless motor provides longer life and cooler operating temps.
    The aluminum case design not only looks good but also allows for cooler and smoother operating temps.
    Our servos are totally green - from materials to production, these servos are environmentally friendly.
    Intended for use in heli rudder applications only.

    Specification:

    • Dimensions(mm)     40.3 x 20.2 x 38.7
    • Weight(g):     69.0
    • Speed @6.0V:     .06sec
    • Torque@6.0V:     69.4 oz-in
    • Speed @ 7.4V:     .048sec
    • Torque @ 7.4V:     138.9 oz-in.
    • Gear Type:     Metal
    • Bearings:     2 BB
    • Frequency:     250-333Hz
    • Pulse Width Frequency:     1520>
    SKU: SB-2283MG
    €159.90
    inc. VAT

     72HR STOCK
  • SAVÖX SB-2271SG BRUSHLESS

    SAVÖX SB-2271SG BRUSHLESS

    SAVÖX SB-2271SG DIGITAL SERVO BRUSHLESS MOTOR HIGH VOLTAGE STEEL GEARS (STANDARD SIZE)

    Specifications Dimension :

    • Height: 38,5 mm Dimension :
    • Length: 40,3 mm Dimension :
    • Weight: 69 gr Dimension :
    • width: 20,2 mm
    • Speed: 0.085 sec / 60° @ 6,0v
    • Torque: 15.0 kg- cm @ 6,0v
    • Type of case: Aluminium + plastic
    • Type of gears: Steel gears
    • Type of motor: Brushless motor
    • Type of servo: Digital servo
    • Type of spine: 25 tooth spine
    SKU: SB-2271SG
    €119.00
    inc. VAT

     72HR STOCK
  • SAVÖX SB-2272MG BRUSHLESS

    SAVÖX SB-2272MG BRUSHLESS

    SAVÖX SB-2270SG DIGITAL SERVO BRUSHLESS MOTOR HIGH VOLTAGE METAL GEARS (STANDARD SIZE)

    Features:

    Combines leading edge technology with super high 12 bit (4096) resolution and unique steel gears.
    Super light-weight.
    Brushless motor provides extremely high speed, incredible efficiency, and amazingly low power consumption.
    The full aluminum case design not only looks good but also allows for cooler and smoother operating temps.
    Our servos are totally green – from materials to production, these servos are environmentally friendly.
    Ideal for Gyro and rudder servo only.

    Specifications:

    • Dimensions(mm): 40.3x20.2x38.5
    • Weight(g): 66.0
    • Speed(@4.8V sec/60): .055
    • Torque(@4.8V oz-in): 41.7
    • Speed(@6.0V sec/60): .045
    • Torque(@6.0V oz-in): 69.4
    • Speed(@7.4V sec/60): .032
    • Torque(@7.4V oz-in): 97.2
    • Gear: Metal
    • Bearing: 2BB
    • Case: Full Aluminum
    • 25 Tooth Spline
    • Frequency: 250-333hz
    SKU: SB-2272MG
    €119.00
    inc. VAT

     72HR STOCK
  • Savox SB-2282SG Digital High Voltage Brushless Motor Servo, Steel Gear

    Savox SB-2282SG Digital High Voltage Brushless Motor Servo, Steel Gear

    Savox SB-2282SG Digital High Voltage Brushless Motor Servo, Steel Gear

    Features:

    • Leading edge digital servo technology
    • High efficiency Brushless motor
    • Accurate and fast response
    • Super high resolution
    • Aluminium case for improved motor cooling and total strength
    • Ball beared
    • Precision Steel gears

    Technical specifications:

    • Servo Technology: Digital High Voltage
    • Input Voltage (V): 6.0V 7.4V
    • Servo Type / Size: Standard
    • Motor Type: Brushless Motor
    • Gear Material: Steel Gears
    • Ball Beared: Ball Beared
    • Servo Case: Aluminium
    • Speed 60°/Sec @ 7.4V: 0.075 Sec/60°
    • Torque kg/cm @ 7.4V: 23.0 Kg/cm
    • Length (mm): 40.3 mm
    • Width (mm): 20.2 mm
    • Height (mm): 38.7 mm
    • Weight (g): 81 g
    • Connector type: JR
    • Spline size: 25T Spline
    SKU: SB-2282SG
    €159.90
    inc. VAT

     72HR STOCK
  • Scorpion Motor HK-5035-380 (XXtreme Edition)

    Scorpion Motor HK-5035-380 (XXtreme Edition)

    Scorpion Motor HK-5035-380 (XXtreme Edition)

    The Scorpion HKIII-5035-380 motor will provide all the power you need for the larger 800 class electric helicopters, those massive electric powered scale projects or for your workhorse camera platform helicopters that need to be able to lift heavy weights reliably.

    Scorpion HK Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold anodized to provide a beautiful, long-lasting finish. The stators are made with high quality laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

    Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

    For the best overall combination of quality, performance, and value, use Scorpion Motors in your helicopter!

    Specifications:

    • Stator Diameter 50 mm (1.56 in)
    • Stator Thickness 35 mm (1.37 in)
    • No. of Stator Arms 12
    • Magnet Poles10
    • Motor Wind 10
    • Motor Kv 380 KV RPM / Volt
    • No-Load Current (IO/8.4v) 1.75 Amps
    • Max Continuous Current 100 Amps
    • Max Continuous Power 4800 Watts
    • Weight 697 Grams
    • Outside Diameter 61 mm (2.4 in)
    • Shaft Diameter 7.98 mm (0.31 in)
    • Body Length 66 mm (2.59 in)
    • Overall Shaft Length 122 mm (4.80 in)
    • Max Lipo Cell 14s
    SKU: MIK-4590
    €379.00
    inc. VAT

     LOW STOCK
  • Screw Set Chassis, LOGO 700 & 800 XXtreme

    Screw Set Chassis, LOGO 700 & 800 XXtreme

    Screw Set Chassis, LOGO 700 & 800 XXtreme
    SKU: MIK-4551
    €9.90
    inc. VAT

     72HR STOCK
  • Servo Mounting for Savöx LOGO XXtreme 700 & 800

    Servo Mounting for Savöx LOGO XXtreme 700 & 800

    Servo Mounting for Savöx LOGO XXtreme 700 & 800

    SKU: MIK-4587
    €19.90
    inc. VAT

     72HR STOCK
  • Servo Mounting Frame LOGO XXtreme 700 & 800

    Servo Mounting Frame LOGO XXtreme 700 & 800

    Servo Mounting Frame, LOGO XXtreme 700 & 800
    SKU: MIK-4547
    €29.90
    inc. VAT

     72HR STOCK
  • Servo mounting set JR/Futaba HV, LOGO XXtreme 700 & 800

    Servo mounting set JR/Futaba HV, LOGO XXtreme 700 & 800

    Servo mounting set JR/Futaba HV, LOGO XXtreme 700 & 800

    SKU: MIK-4588
    €19.90
    inc. VAT

     LOW STOCK
  • Servo Wire Braided Sleeving Wrap, 1 Meter - LOGO XXtreme 700 & 800

    Servo Wire Braided Sleeving Wrap, 1 Meter - LOGO XXtreme 700 & 800

    Servo Wire Braided Sleeving Wrap, 1 Meter - LOGO XXtreme 700 & 800

    SKU: MIK-4593
    €4.50
    inc. VAT

     IN STOCK
  • Sideframe Left, LOGO XXtreme 800

    Sideframe Left, LOGO XXtreme 800

    Sideframe left, LOGO XXtreme 800
    SKU: MIK-4533
    €69.00
    inc. VAT

     72HR STOCK
  • Sideframe right, LOGO XXtreme 800

    Sideframe right, LOGO XXtreme 800

    Sideframe right, LOGO XXtreme 800
    SKU: MIK-4532
    €69.00
    inc. VAT

     72HR STOCK
  • Socket Head Cap M3x22 Screw (4 pcs)

    Socket Head Cap M3x22 Screw (4 pcs)

    Socket head cap screw M3x22 (4 pieces)

    SKU: MIK-1916
    €2.40
    inc. VAT

     72HR STOCK
  • Socket Head Cap Screw M3 x 8 (10 pcs)

    Socket Head Cap Screw M3 x 8 (10 pcs)

    Socket head cap screw M3x8

    SKU: MIK-1952
    €3.00
    inc. VAT

     IN STOCK
  • Socket Head Cap Screw M3x10 (10 pcs)

    Socket Head Cap Screw M3x10 (10 pcs)

    Socket head cap screw M3x10

    SKU: MIK-1953
    €3.00
    inc. VAT

     LOW STOCK
  • Spacer for bevel pinion, LOGO XXtreme 700 & 800

    Spacer for bevel pinion, LOGO XXtreme 700 & 800

    Spacer for bevel pinion, LOGO XXtreme 700 & 800
    SKU: MIK-4525
    €7.50
    inc. VAT

     72HR STOCK
  • Spacer for blade holder 12mm, LOGO 700 & 800 XXtreme

    Spacer for blade holder 12mm, LOGO 700 & 800 XXtreme

    Spacer for blade holder 12mm, LOGO 700 & 800 XXtreme

    SKU: MIK-4792
    €18.00
    inc. VAT

     72HR STOCK
  • Spacer for blade holder 14mm, LOGO 700 & 800 XXtreme

    Spacer for blade holder 14mm, LOGO 700 & 800 XXtreme

     Spacer for blade holder for 14mm blade grip (EDGE 753), LOGO 700 & 800 XXtreme

    SKU: MIK-4758
    €17.90
    inc. VAT

     72HR STOCK
  • Spacer for blade holder LOGO XXtreme 700 & 800

    Spacer for blade holder LOGO XXtreme 700 & 800

    Spacer for blade holder, LOGO XXtreme 700 & 800
    SKU: MIK-4592
    €18.00
    inc. VAT

     72HR STOCK
  • Spindle Shaft For Tail Rotor Hub, LOGO XXtreme 700 & 800

    Spindle Shaft For Tail Rotor Hub, LOGO XXtreme 700 & 800

    Spindle Shaft For Tail Rotor Hub, LOGO XXtreme 700 & 800
    SKU: MIK-4571
    €7.90
    inc. VAT

     72HR STOCK
  • Spindle shaft rotor head, LOGO 700

    Spindle shaft rotor head, LOGO 700

     Spindle shaft rotor head, LOGO 700

    SKU: MIK-4703
    €12.90
    inc. VAT

     LOW STOCK
  • Spindle shaft rotor head, LOGO XXTreme 800

    Spindle shaft rotor head, LOGO XXTreme 800

    Spindle shaft rotor head, LOGO XXTreme 800



    SKU: MIK-4503
    €12.90
    inc. VAT

     72HR STOCK
  • Steel Balls with 3mm Hole (4pcs)

    Steel Balls with 3mm Hole (4pcs)

    Steel balls with 3mm hole (4pcs)

    For all LOGO

    SKU: MIK-1574
    €5.60
    inc. VAT

     72HR STOCK
  • Stiffening Frame For Motorplate LOGO XXtreme 700 & 800

    Stiffening Frame For Motorplate LOGO XXtreme 700 & 800

    Stiffening Frame For Motorplate, LOGO XXtreme 700 & 800
    SKU: MIK-4546
    €26.50
    inc. VAT

     72HR STOCK

Manufacturers

Back