Speed controllers & Accessories

Products


  • Hobbywing Platinum HV 6-14s ,130A-V4 ESC SPEED CONTROLLER BEC 10A

    Hobbywing Platinum HV 6-14s ,130A-V4 ESC SPEED CONTROLLER BEC 10A

    Platinum V4 serial products allows the motor to start extremely smooth and avoids tail-drift
    issues that helicopters experience. The start-up time is adjustable from 8 to 25 seconds,
    this will definitely create a perfect starting point for every flight.

    Excellent Motor Speed Governing
    High-performance 32-bit processor with a running frequency of 72MHz combined with
    advanced algorithm optimizes the speed governing. Together with the adjustable
    governor parameters guarantee every pilot a precise control experience.

    High Voltage Built-in BEC
    The built-in switch mode BEC with an adjustable voltage range from 5V to 8V, a continuous current of
    over 10A and peak current of 25A can supply enough power for your servos to operate efficiently.

    Specifications:

    • Product Name: Platinum HV 130A V4
      Type: Brushless, High Voltage
      Cont./Peak Current: 130A/160A
      Input: 6-14S LiPo
      BEC Output: Switch Mode:5-8V,10A
      Input Wires: Red-12AWG-150mm*1/Black-12AWG-150mm*1
      Output Wires: Black-12AWG-100mm*3
      (Note: All the wire length above is the original length not the length you see from the outside.)
      Transmitter: Not Supported
      LED Program Card: Not Supported
      LED Program Box: Not Supported
      LCD Program Box: Supported
      WiFi Module: Supported
      Program Port: Separate Program Port
      Firmware Upgrade: Supported
      Size: 101.0x45.5x27.0mm
      Weight: 169g
      Applications: 550-600 Class Heli (Main Blade: 550-690mm)
                              .90-.140 Class Fixed-wing Airplane, 2m FAIF3A & 3D
                              EDF (with Diameter≦105mm)
    SKU: HW30209200
    €299.00
    inc. VAT

     LOW STOCK
  • Hobbywing Platinum HV 6-14s LIPO 130A V4 Brushless ESC OPTO

    Hobbywing Platinum HV 6-14s LIPO 130A V4 Brushless ESC OPTO

    Excellent Motor Speed Governing

    • High-performance 32-bit processor with a running frequency of 72MHz combined with advanced algorithm optimizes the speed governing.
    • Together with the adjustable governor parameters guarantee every pilot a precise control experience.

     
    A separate program port for connecting programmer on this ESC allows user to

    • Program ESC,
    • Check flight data include minimum voltage, maximum temperature, standardized RPM and speed curve (in Heli Governing Store mode) of the flight parameters recorded by the ESC,
    • Upgrade ESC firmware with a mutifunction LCD program box or a WiFi Module & our Apple/Android phone App.

    DEO Technology

    • The DEO (Driving Efficiency Optimization or so-called “Active Freewheeling”)
    • technology implemented in the ESC has multiple advantages.
    • Rapider response to throttle change.
    • Higher driving efficiency, longer flight time.
    • Lower ESC temperature and a more reliable operation.

    Specifications:

    • Type: Brushless, High Voltage
    • Cont./Peak Current: 130A/160A
    • Input: 6-14S LiPo
    • BEC Output: No
    • Input Wires: Red-12AWG-150mm*1/Black-12AWG-150mm*1
    • Output Wires: Black-12AWG-100mm*3
    • Input Connectors: No
    • Output Connecotors: No
    • (Note: All the wire length above is the original length not the length you see from the outside.)
    • Transmitter: Not Supported
    • LED Program Card: Not Supported
    • LED Program Box: Not Supported
    • LCD Program Box: Supported
    • WiFi Module: Supported
    • Program Port: Separate Program Port
    • Firmware Upgrade: Supported
    • Size: 101.0x45.5x27.0mm
    • Weight: 154g
    • Applications:
      • 550-600 Class Heli (Main Blade: 550-690mm)
      • .90-.140 Class Fixed-wing Airplane, 2m FAIF3A & 3D
      • EDF (with Diameter≦105mm)
    SKU: HW30209201
    €229.00
    inc. VAT

     LOW STOCK
  • Hobbywing Platinum PRO 100A HV 5-12S OPTO

    Hobbywing Platinum PRO 100A HV 5-12S OPTO

    Hobbywing Platinum PRO 100A OPTO HV 5-12S (no BEC)

    High-performance microprocessor with the operating frequency up to 50MHz brings excellent compatibility
    (with most motors in the market) and high driving efficiency.
    Multiple flight modes: Fixed Wing Airplane/ Heli with Governor Off/ Heli with Governor (Elf) / Heli with Governor Store.
    The Hobbywing Platinum V3 100A-HV is a 100 Amp ESC with a high performance microprocessor. This ESC is a great choice for fixed wing aircraft, and 550 to 600 class helicopter applications running between 5 and 12S (16.8-50.4V).

    Features:
    High-performance microprocessor with the operating frequency up to 50MHz brings excellent compatibility (with most motors in the market) and high driving efficiency.
    The maximum motor speed can reach 210000 RPM (for 2-pole), 70000 RPM (for 6-pole) and 35000 RPM (for 12-pole).
    Multiple flight modes: Airplane Fixed Wing / Heli Governor Off / Heli Governor (Elf) / Heli Governor Store.
    Adjustable throttle range, compatible with various transmitters.
    Microprocessor powered by independent DC regulator has better anti-interference performance, which greatly reduces the risk of losing control.
    Brand new governor program brings excellent speed-governing effect.
    ”Restart in auto rotation" can manually interrupt the auto rotation and quickly restart the motor to avoid crashes caused by incorrect operations.
    Independent output port for RPM (that is: motor speed) signals.
    Compatible LCD program box (optional accessory), its simple and visual interface allows users to set/revise all the ESC parameters easily.
        (For detailed information, please refer to User Manual of LCD Program Box.)
    Upgradeable firmware, you can upgrade the ESC after connecting it to a PC via the USB cable on the program box.
    The independent port, for connecting the program box and setting parameters, can also be the output port of the running status data of the ESC. When coordinating with the data transmission module, it can make the real-time data monitoring and logging possible.
    Low-voltage cutoff protection / Throttle signal loss protection effectively prolong the service life of the ESC.
    The anti-spark circuit on the input wires eliminates the electro spark created when connecting the battery pack to the ESC.

    Specifications:

    • Model: Platinum-100A-HV-V3
    • Main Application: 550-600 classes helicopter (600-620mm blade)
    • Input: 5-12S LiPo, 16.8-50.4V
    • Cont. / Burst Current     Cont. 100A / Burst 140A (in 10 sec)
    • BEC: Without built-in BEC
    • Programming Port: The programming port can provide 5.5V/100mA power supply to the program box or the external cooling fan
    • Throttle Signal and RPM signal     Signal transferred via optoelectronic coupler
    • Input / output Wires: Input:12AWG / Output:12AWG
    • Weight/Size: 104g / 77x35x21mm(without cooling fan),
    • 110g / 77x35x32mm (with cooling)
    SKU: HW30203600
    €139.90
    inc. VAT

     IN STOCK
  • Hobbywing Platinum PRO V3 50A 2-6S BEC 7A for 450 3D Heli size

    Hobbywing Platinum PRO V3 50A 2-6S BEC 7A for 450 3D Heli size

    Hobbywing Platinum PRO V3 50A 2-6S BEC 7A for 450 3D Heli size

    The Hobbywing Platinum V3 50A is a 50 Amp ESC with a high performance microprocessor.
    This ESC is a great choice for fixed wing aircraft, and 480 to 550 class helicopter applications running between 2 to 6S Lipo (5.2V-25.2V).

    Features:

    High-performance microprocessor with the operating frequency up to 50MHz brings excellent compatibility (with most motors in the market) and high driving efficiency.
    The maximum motor speed can reach 210000 RPM (for 2-poles), 70000 RPM (for 6-poles) and 35000 RPM (for 12-poles).
    Multiple flight modes: Fixed Wing Airplane/ Heli with Governor Off/ Heli with Governor (Elf) / Heli with Governor Store.  
    Adjustable throttle range, compatible with various transmitters. It brings smooth, soft & linear speed adjustment and rapid throttle response.
    Microprocessor powered by independent DC regulator has better anti-interference performance, which greatly reduces the risk of losing control.
    Built-in high-efficient & high-power (switch mode) BEC can make the output voltage switched among 5.2V / 6.0V / 7.4V / 8.4V. (*For the specific output voltage, please refer to the parameter list below.)
    Brand new governor program, easy to operate; and its excellent speed-governing effect can make big rotor blades more stable even under rapid load change.
    ”Restart in auto rotation" can manually interrupt the auto rotation and quickly restart the motor to avoid crashes caused by incorrect operations.
    Independent output port for RPM (that is: motor speed) signals.
    Compatible LCD program box (*optional accessory), its simple and visual interface allows users to set/revise all the ESC parameters easily. (For detailed information, please refer to User Manual of LCD Program Box.)
    Upgradeable firmware, you can upgrade the ESC after connected it to a PC via the USB cable on the program box.
    The independent port, for connecting the program box and setting parameters, can also be the output port of the running status data of the ESC. When coordinating with the data transmission module, it can make the real-time data monitoring and logging possible.
    Multiple protection features including input voltage abnormality protection/ low-voltage cutoff protection/ throttle signal loss protection effectively prolong the service life of the ESC.

    Specifications:

    • Model: Platinum-50A-V3
    • Main Application: 480-550 class (helis)
    • Battery Count: 2-6S Lipo, 5.2V-25.2V
    • Cont./Burst Current: 100A/150A (burst in 10 sec)
    • BEC Output
    • Switch Mode BEC, 6.0V/7.4V/8.4V; Cont.: 10A, Burst: 25A
    • BEC has the cut-through protection (which means the battery voltage won’t get through to the receiver if the BEC is accidentally damaged)
    • Switch Mode BEC, 5.2V/6.0V/7.4V
    • Cont.: 7A, Burst: 15A
    • Input: 12AWG / Output:12AWG
    • Input: 14AWG / Output: 14AWG
    • Weight/Size:
    • 104g / 70mm*35mm*21mm(W/O fan)
    • 110g / 70mm*35mm*32mm(W/ fan)
    • 49g / 48mm*30mm*15.5mm
    SKU: HW30215101
    €59.90
    inc. VAT

     LOW STOCK
  • Hobbywing Platinum PRO V4 120A ESC (3S-6S) BEC 25A

    Hobbywing Platinum PRO V4 120A ESC (3S-6S) BEC 25A

    Hobbywing Platinum PRO V4 120A ESC SPEED controller for RC models (3S-6S) BEC 25A

    Super Soft Start-up

    • Platinum V4 serial products allows the motor to start extremely smooth and avoids tail-drift issues that helicopters experience.
    • The start-up time is adjustable from 8 to 25 seconds, this will definitely create a perfect starting point for every flight.

    Excellent Motor Speed Governing

    • High-performance 32-bit processor with a prossesing frequency of 72MHz combined with advanced algorithm optimizes the speed governing.
    • Together with the adjustable governor parameters it will guarantee every pilot a precise and efficient control experience.

    High Voltage Built-in BEC

    • The built-in switch mode BEC with an adjustable voltage range from 5V to 8V, a continuous current of over 10A and peak current of 25A can supply enough power for your HV servos to operate at their peak.

    DEO Technology

    • The DEO (Driving Efficiency Optimization or so-called “Active Freewheeling”)
    • technology implemented in the ESC has multiple advantages.
    • A very Rapid response to throttle change.
    • Higher driving efficiency, longer flight time.
    • Lower ESC temperature and a much more reliable operation during flight.

    Other Features

    • A separate program port for connecting programmer on this ESC allows user to
    • Program ESC,
    • Check flight data include minimum voltage, maximum temperature, standardized RPM and
    • speed curve (in Heli Governing Store mode) of the flight parameters recorded by the ESC,
    • Upgrade ESC firmware with a mutifunction LCD program box or a WiFi Module & our
    • Apple/Android phone App.

    Four Brake Modes

    • This Platinum 80A V4 ESC has “Brake Disabled, Normal Brake, Proportional
    • Brake and Reverse Brake” four brake modes. The brake amount is adjustable in normal brake mode; in proportional brake mode, the brake force will be automatically selected based on the position of radio throttle stick; in reverse brake mode, the motor rotation can be changed via a spare transmitter channel.

    Multiple Protections

    • Multiple protection features include ESC thermal, capacitor thermal (HOBBYWING-patented technology), ESC overload, throttle signal loss(or Fail Safe), and low voltage cutoff effectively prolongs the service life of the ESC.

    Specifications:

    • Product Name: Platinum 120A V4
    • Type: Brushless, Regular
    • Specifications
    • Cont./Peak Current: 120A/150A
    • Input: 3-6S LiPo
    • BEC Output: Switch Mode:5-8V,10A
    • Input Wires: Red-12AWG-150mm*1/Black-12AWG-150mm*1
    • Output Wires: Black-12AWG-100mm*3
    • Input Connectors: No
    • Output Connecotors: 4.0mm Gold Connectors (Female)
    • (Note: All the wire length above is the original length not the length you see from the outside.)
    • ESC Programing via:
    • Transmitter: Not Supported
    • LED Program Card: Not Supported
    • LED Program Box: Not Supported
    • LCD Program Box: Supported
    • WiFi Module: Supported
    • Program Port: Separate Program Port
    • Firmware Upgrade: Supported
    • Size: 84.3x38.2x20.4mm
    • Weight: 107g
    • Applications:
      • 500-550 Class Heli (Main Blade: 470-575mm)
      • .70-.90 Class Fixed-wing Airplane 3D, Light Weight FAIF3A
      • EDF (with Diameter≦90mm)
    SKU: HW30203401
    €189.00
    inc. VAT

     LOW STOCK
  • Hobbywing Platinum PRO V4 160A-HV 14S ESC SPEED controller BEC 25A

    Hobbywing Platinum PRO V4 160A-HV 14S ESC SPEED controller BEC 25A

    This is the Hobbywing Platinum Pro V4 160HV ESC, for use with 700-800 sized Helicopters.  

    One of a Kind Design
    The elegant case is made from aluminum alloy material. Each cooling slot and its fin were carefully designed and arranged, and the case has gone through oxidation, coloring and edge-highlighting.

    Innovative Heat Dissipation Structure
    The innovative "duo" stacking structure allows all components on both sides of the printed circuit boards to quickly conduct heat to the aluminum case.

    Excellent Motor Speed Governing
    The high performance 32-bit processor, combined with advanced algorithm, makes the motor speed-governing excellent for different conditions. With the adjustable sensitivity of speed-governing, every pilot can find the most suitable settings for his helicopter.

    Super Soft Start-Up
    The Platinum-HV-160A makes the motor start extremely soft and avoids tail-drift issues. The start-up time is adjustable within 8 to 25 seconds. This will definitely create a perfect starting point for every flight.

    Super BEC
    The built-in switch mode BEC with a continuously adjustable output voltage, range from 5V to 8V (steps: 0.1V). It is certain to put out the power you need for rapid, precise steering servo operation.

    Great Current Endurance
    A high-quality and high-voltage MOSFET with a great current endurance guarantees the ESC's safety especially in a extremely high power demanding situation.

    Built-in Sparkproof Circuit
    Built-in sparkproof circuit effectively eliminates sparks produced at the "powering-on" moment and prolongs the connectors lifespan.

    Specifications:

    • Main Applications: 700-800 Class Helis
    • Governor: Internal
    • Built-in BEC: Yes, Adjustable; 5-8V (10A continuous; 25A burst current)
    • Continuous Current: 160A
    • Cell Count: 6-14S
    • Case: Aluminum Alloy Shell
    • Programming:
    • Peak Current: 200A
    • Weight: 282g
    • Dimensions: 106x50x34mm
    • DEO Technology: Yes
    • Spark-Proof: Yes
    • Programming: Separate port for ESC programming (this port is also the FAN port)
    SKU: HW30203700
    €499.90
    inc. VAT

     LOW STOCK
  • Hobbywing Platinum PRO V4 200A HV 14S ESC SPEED CONTROLLER OPTO

    Hobbywing Platinum PRO V4 200A HV 14S ESC SPEED CONTROLLER OPTO

    The Platinium series are the Professional Series for the RC model flying field. Perfect tunable control panel for airplains and heli's. They are the most powerful BEC systems used as high-voltage controller without BEC system.

    Features:

    • Current 200 A, max. briefly: 250 A
    • Input: 6-14S LiPo 22.2 V 58.8 V
    • BEC Output: No
    • Input / output cable: Input: 10AWG / output: 10AWG
    • Scope: 700-800 Heli classes, large aircraft
    • Dimensions: 106x50x40
    • Weight: 305 g (with input & output cable on the ESC soldered)

    Specfication:

    • Cells:6-14 LiPo
    • Normal: A200
    • Max A 250
    • BEC:no BEC-OPTO
    • Size: 106/50/40 mm
    • Weight: 305 g
    • Type: Brushless
    SKU: HW30209100
    €509.90
    inc. VAT

     72HR STOCK
  • Hobbywing Platinum PRO V4-60A 3-6S LIPO, BEC 18A

    Hobbywing Platinum PRO V4-60A 3-6S LIPO, BEC 18A

    Hobbywing Platinum PRO V4-60A 3-6S LIPO, BEC 18A

    Specifications:

    • Type: Brushless
    • Cont./Peak Current: 60A/80A
    • Input: 3-6S Lipo
    • BEC Output: Switch Mode: 5-8V, 7A
    • Wires&Connectors:
    • Input Wires: Red-14AWG-100mm*1/Black-14AWG-100MM*1
    • Output Wires: Black-14AWG-75mm*3
    • Input Connectors: No
    • Output Connectors: 3.5mm Gold Connectors (Female)

    (Note: All the wire length above is the original length not the length you see from the outside.)

    • ESC Programing via: Trasmitter: Not Supported
    • ESC Programing via LED Program Card: Not Supported
    • ESC Programing via LED Program Box: Not Supported
    • ESC Programing via LCD Program Card: Supported
    • WIFI Module: Supported
    • Program Port: Program/Throttle Wire
    • Firmware: Firmware Upgrade: Supported
    • Size: 48.0x30.0x15.5mm
    • Weight: 49g
    • Application: 450-480 Class Heli(Propeller: 325-326mm)
    SKU: HW30215100
    €69.00
    inc. VAT

     LOW STOCK
  • Hobbywing WiFi Express Smartphone ESC Module

    Hobbywing WiFi Express Smartphone ESC Module

    Hobbywing WiFi Express Smartphone ESC Module    

    The WiFi Module builds wireless connection between ESC and smartphone or computer. Then the user can set the ESC parameters, upgrade the the ESC Firmware, real time monitor the motor RPM and the Battery voltage etc. through the application program in the smartphone or computer.

    Features:

    • Connecting the ESC via WiFi with the smartphone or PC / Laptop
    • ESC programming without complicated wiring
    • Firmware update
    • Motor Data monitoring like RPM in real time
    • Battery voltage monitoring in real time

    Technical Data:

    • Size (LxWxH): 28,7 x 25,7 x 8,8mm
    • Input Voltage: 5 - 12.6V
    • Wireless Protocol: IEEE802.11 b/g/n
    • Reach: 0-10m (without obstacles)

    The WiFi Express Module is suitable for these ESC:

    • XERUN Series v2.0 and v3.0
    • EZRUN Series v2.0
    • Platinum Series

     

    SKU: HW3050300
    €54.90
    inc. VAT

     IN STOCK
  • Jive 100+ LV Kontronik Speed controller

    Jive 100+ LV Kontronik Speed controller

    The JIVE follows a concept that will convince you. Its functionality exceeds all you have ever heard about ESCs.

    High-tech unit
    It's integrated shock-resistant housing, made from a specific polyamide, protects the JIVE ESCs from mechanical damage and makes it waterproof. The plastic material has been developed especially for injection moulding of electronic parts.

    Power by coolness
    Noticeable is the huge cooling plate. It is perfectly connected with the power parts, provides good heat transfer and enables additional cooling to be realized. It is possible to raise the performance enormously by installing an additional air or water cooler system. The naming 80+ means: minimum 80 A. With a good extra cooler it is possible to increase to double power

    BEC records
    Further highlights are waiting inside, for example the strong BEC which is adjustable between 5 V and 6 V with PROGCARD II. It offers 5 A continuous BEC current with 15 A in peak.

     

    Special Features :

    • 6-25 V
    • 100 A continuous current 130 A Surge.
    • BEC 5A continuous current
    • 92g with cabels
    SKU: KON-4604
    €279.00
    inc. VAT

  • Kontronic ProgUNIT for Kontronik Kosmik and Jive Pro ESC

    Kontronic ProgUNIT for Kontronik Kosmik and Jive Pro ESC

    ProgUNIT for Kontronik Kosmik and Jive Pro ESC

    Easy Update & Programming your Kontronik ESC with USB ProgUnit
    For KOSMIK & JIVE PRO ESC
     

    • USB for PC / Laptop
    • Easy Update of Firmare
    • ESC Programming with PC Software (release End of October 2014)
    • PC Software available for Donwload at Kontronik website (free of costs)
    SKU: KON-9311
    €59.00
    inc. VAT

     LOW STOCK
  • Kontronic TelMe module interface for FUTABA RX Telemetry

    Kontronic TelMe module interface for FUTABA RX Telemetry

    Kontronic TelMe module interface for FUTABA RX Telemetry

    The TelMe module is the interface between a KOTRONIK ESC with module port and a receiver prepared for telemetry.
    TelMe is recognized automatically by the ESC and the correct data stream is started.

    Both modules can be run with telemetry-ready ESCs from KONTRONIK (KOSMIK and JIVE Pro) and appropriate radio controls from MIKADO (V-Bar) and Ex-Bus-prepared radio controls from JETI (DS-14 / -16, DC-14 / -16).

    With many major radio manufacturer offering telemetry systems, KONTRONIK DRIVES is now connected. ESCs having a modul port are designed with an integrated  interface for telemetry. Simply connect the TelMe interface into one of the module ports on the ESC and you will automatically receive important logging data on your transmitter.

    TelMe allows the interference-free transportation of telemery signals from the ESC to the transmitter. The ESC recognizes automatically which module is connected.

    Datas generated:

    • Motor current
    • Battery voltage
    • Used capacity of the battery
    • Temperature of the power board
    • BEC current (when ESC has an internal  BEC current mesurement)
    • BEC temperature
    • PWM %
    • Motor RPM, eg. rotor RPM

    The following alarms are shown:

    • amplifier temperature
    • motor current
    • BEC temperature

    Furthermore the TelMe Mikado shows the following limits:

    • min voltage
    • max current (mean and peak)
    • BEC min voltage
    • BEC max temperature
    • amplifier max temperature

    Make sure to have installed the latest software version on your radio control and ESC. KONTRONIK provides a particular software update on the homepage.

    SKU: KON-9740
    €89.90
    inc. VAT

     72HR STOCK
  • Kontronic TelMe module interface for JETI RX Telemetry

    Kontronic TelMe module interface for JETI RX Telemetry

    Kontronic TelMe module interface for JETI RX Telemetry

    The TelMe module is the interface between a KOTRONIK ESC with module port and a receiver prepared for telemetry.
    TelMe is recognized automatically by the ESC and the correct data stream is started.

    Both modules can be run with telemetry-ready ESCs from KONTRONIK (KOSMIK and JIVE Pro) and appropriate radio controls from MIKADO (V-Bar) and Ex-Bus-prepared radio controls from JETI (DS-14 / -16, DC-14 / -16).

    With many major radio manufacturer offering telemetry systems, KONTRONIK DRIVES is now connected. ESCs having a modul port are designed with an integrated  interface for telemetry. Simply connect the TelMe interface into one of the module ports on the ESC and you will automatically receive important logging data on your transmitter.

    TelMe allows the interference-free transportation of telemery signals from the ESC to the transmitter. The ESC recognizes automatically which module is connected.

    Datas generated:

    • Motor current
    • Battery voltage
    • Used capacity of the battery
    • Temperature of the power board
    • BEC current (when ESC has an internal  BEC current mesurement)
    • BEC temperature
    • PWM %
    • Motor RPM, eg. rotor RPM

    The following alarms are shown:

    • amplifier temperature
    • motor current
    • BEC temperature

    Furthermore the TelMe Mikado shows the following limits:

    • min voltage
    • max current (mean and peak)
    • BEC min voltage
    • BEC max temperature
    • amplifier max temperature

    Make sure to have installed the latest software version on your radio control and ESC. KONTRONIK provides a particular software update on the homepage.

    SKU: KON-9770
    €89.90
    inc. VAT

     LOW STOCK
  • Kontronic TelMe module interface for MIKADO RX Telemetry

    Kontronic TelMe module interface for MIKADO RX Telemetry

    Kontronic TelMe module interface for MIKADO RX Telemetry

    The TelMe module is the interface between a KOTRONIK ESC with module port and a receiver prepared for telemetry.
    TelMe is recognized automatically by the ESC and the correct data stream is started.

    Both modules can be run with telemetry-ready ESCs from KONTRONIK (KOSMIK and JIVE Pro) and appropriate radio controls from MIKADO (V-Bar) and Ex-Bus-prepared radio controls from JETI (DS-14 / -16, DC-14 / -16).

    With many major radio manufacturer offering telemetry systems, KONTRONIK DRIVES is now connected. ESCs having a modul port are designed with an integrated  interface for telemetry. Simply connect the TelMe interface into one of the module ports on the ESC and you will automatically receive important logging data on your transmitter.

    TelMe allows the interference-free transportation of telemery signals from the ESC to the transmitter. The ESC recognizes automatically which module is connected.

    Datas generated:

    • Motor current
    • Battery voltage
    • Used capacity of the battery
    • Temperature of the power board
    • BEC current (when ESC has an internal  BEC current mesurement)
    • BEC temperature
    • PWM %
    • Motor RPM, eg. rotor RPM

    The following alarms are shown:

    • amplifier temperature
    • motor current
    • BEC temperature

    Furthermore the TelMe Mikado shows the following limits:

    • min voltage
    • max current (mean and peak)
    • BEC min voltage
    • BEC max temperature
    • amplifier max temperature

    Make sure to have installed the latest software version on your radio control and ESC. KONTRONIK provides a particular software update on the homepage.

    SKU: KON-9775
    €89.90
    inc. VAT

  • Kontronik Cool Kosmik 200 HV ESC

    Kontronik Cool Kosmik 200 HV ESC

    This is the Cool Kosmik 200+ HV which has an integrated heat sink
    If you love style and function, the Cool KOSMIK is made just for you. With an integrated fan combined with an active heat sink, you will find no better cooling solution available. You will immediately notice the stylish design of the integrated cooling plate, and will appreciate the active cooling fan in low airflow situations.

    COOL KOSMIK, a design that is made for the most demanding situations. COOL KOSMIK ESCs will have their own designated order numbers.

    • 5-14 Lipo, 20-59 V
    • 200 A continuous current
    • BEC 10 A continuous current
    • BEC 30A peak current
    • 108 x 53 x 44.5 mm
    • 250 g without cable

    SKU: KON-48201
    €739.00
    inc. VAT

     72HR STOCK
  • Kontronik Fan for Kosmik 09477

    Kontronik Fan for Kosmik 09477

    Kontronik Fan for Kosmik 09477

    SKU: KON-9477
    €42.99
    inc. VAT

     72HR STOCK
  • Kontronik JIVE PRO 120+ HV 120A 5-12S speed controller

    Kontronik JIVE PRO 120+ HV 120A 5-12S speed controller

    Kontronik JIVE PRO 120+ HV 120A 5-12S. At first glance, the new JIVE Pro looks characteristically like the JIVEs you know and trust. As we all know, looks can be deceiving. The JIVE Pro is based upon the KOSMIK processor with many new features, and a brand new chipset that will power you into the future.

    The new BEC of the JIVE Pro can provide power to some of the most demanding servos available when running 8 V and up to 12 S batteries. An exciting feature of the JIVE Pro is the addition of a module port that will allow it to accept and use all KOSMIK modules. For a logging function, the new LogTel module was develloped. It allows to have both functions, logging and telemetry, in one device.

    For Scale Helicopter Pilots, imagine being able to spool up to takeoff head speed over a full minute. Creating a new world of opportunity for scale pilots, the JIVE Pro will allow you to program your startup rate to a full 60 seconds. As the JIVE Pro will provide all helicopter features, there will be no continued need for a helicopter specific ESC such as the HELI JIVE. The JIVE Pro will meet the demands of all types of aircraft, by simply activating the desired features and will become the new leader in the 80-120 A ESC market.

    Off course the new JIVE Pro ESCs include an integrated anti spark function.

    Features:

    • 5-12 Lipo, Imput voltage 16-50 V
    • 120 A continuous current
    • BEC 5-8 V
    • BEC 8 A continuous
    • BEC 20A peak
    • 140g with cable
    • New gas mode/manual throttle mode
    • Combination Mode (Gas mode/governor)
    • FBL-Mode
    • Increased cut-off voltage
    • Increased BEC voltage
    • Continuous governor
    • Extremely low RPM possible
    SKU: KON-4635
    €479.00
    inc. VAT

     72HR STOCK
  • Kontronik Jive PRO 80+HV 80A ESC 16-50V

    Kontronik Jive PRO 80+HV 80A ESC 16-50V

    At first glance, the new JIVE Pro looks characteristically like the JIVEs you know and trust. As we all know, looks can be deceiving. The JIVE Pro is based upon the KOSMIK processor with many new features, and a brand new chipset that will power you into the future.
    The new BEC of the JIVE Pro can provide power to some of the most demanding servos available when running 8 V and up to 12 S batteries.
    Available in both 80 A and 120 A versions, the JIVE Pro offers programming for all types of models including airplanes, helicopters, boats and RC cars.
    An exciting feature of the JIVE Pro is the addition of a module port that will allow it to accept and use all KOSMIK modules. For a logging function, the new LogTel module was develloped. It allows to have both functions, logging and telemetry, in one device.
    The original JIVE set industry standards with its outstanding RPM control and reliable performance. Building upon this heritage, the JIVE Pro is the next evolution of perfection. With the ability to supply power at a speed that surpasses even the original JIVE, the RPM control provided by the new JIVE Pro will astound you. The JIVE Pro is equipped with a new chipset, which provides a greater sensitivity to power demands and removes any noticeable head speed variability. With a new chipset, advanced algorithms, and the flexibility of the sensor port, the JIVE Pro becomes the new standard for all 80-120 A electronic speed controllers.
    For Scale Helicopter Pilots, imagine being able to spool up to takeoff head speed over a full minute. Creating a new world of opportunity for scale pilots, the JIVE Pro will allow you to program your startup rate to a full 60 seconds.
    As the JIVE Pro will provide all helicopter features, there will be no continued need for a helicopter specific ESC such as the HELI JIVE. The JIVE Pro will meet the demands of all types of aircraft, by simply activating the desired features and will become the new leader in the 80-120 A ESC market.
    Off course the new JIVE Pro ESCs include an integrated anti spark function.

     Features:

    • # Expert class performance.
    • # Programmable modes: different default settings for different model types including glider, airplane, heli, car and boat, reversable rotation and competition.
    • # Ultra-low noise suppression circuitry for super-clean BEC power control to the Rx.
    • # Measures motor inductance and winding resistance and matches power accordingly.
    • # Adjustable soft-start timing.
    • # Custom "partial load capability" design allows for very high efficiency when operating at less than full power (brushless systems are most inefficient when operated at less than full power, which can cause overheating and lower flight times).
    • # Adjustable frequency from 8kHz to ultra-high 32kHz for super smooth control and high effiency operation.
    • # EMF brake with 10 brake strength settings.
    • # Capable of much higher RPMs.
    • # Variable current limiting.
    • # Audible tones and LED for easy setup.
    • Cells Input: - 5-12 LiPo
    • Operating Voltage - 16-50 (V)
    • BEC - Yes
    • BEC Voltage - 5.5 (V) Adjustable with ProgCARD II from 5-6 (V)
    • BEC Cont. Amps - 5
    • Constant Current - 80A
    • Max. Surge Current - 100A
    • Dimension - 62Lx32Wx15H mm
    • Weight (w/wires) - 84grams
    SKU: KON-4630
    €339.00
    inc. VAT

     72HR STOCK
  • KONTRONIK KOBY 55 LV 55A 6-25V brushless speed controller

    KONTRONIK KOBY 55 LV 55A 6-25V brushless speed controller

    KONTRONIK KOBY 55 LV 55A 6-25V brushless speed controller

        2-6 Lipo, 6-25 V
        55 A continuous current
        65 A peak current
        BEC 3 A continuous current
        BEC 10 A peak current
        40 g without cable
        55 g with cable

    SKU: KON-4510
    €159.00
    inc. VAT

     72HR STOCK
  • Kontronik KOLIBRI 140 LV

    Kontronik KOLIBRI 140 LV

    Specifications:

    • Voltage: 2-6 S, 6-25V
    • Current: 140 A
    • BEC: 9 V, 10A Current, 30A Peak
    • Weight 160 g
    • Size: 77x23x36 mm

    Kontronik Kolibri LV Series:

    • All versions have a high and stable performance.
    • The KOLIBRI also provides the well-known safety functions of KONTRONIK products.
    • As the software is based on our premium ESC KOSMIK, the KOLIBRI provides an optimal governor for your flight.
    • It also features the well-known soft start-up and the flexible modus programming of the premium segment.
    • In addition, all versions have a very strong BEC with up to 9 V and 10 A continuous current.
    • As a further highlight, we integrated the telemetry functions. So the KOLIBRI provides telemetric data for Futaba,
    • Multiplex, Graupner, Mikado and Jeti without an additional TelMe module.
    • Of course, all versions are prepared for Bluetooth communication and online updates.
    SKU: KON-4340
    €279.00
    inc. VAT

     72HR STOCK
    NEW
  • Kontronik Kosmik 160 HV brushless ESC

    Kontronik Kosmik 160 HV brushless ESC

    4816 Kontronik Kosmik 160 HV ESC

    The KOSMIK delivers sufficient power for the ambitious pilot at the established KONTRONIK reliability. With continuous current of 200A at 5 S to 14 S LiPo brings every model powerfully in motion. The continuous current is defined for a battery capacity of 10,000 mAh.

    With its integrated and adjustable BEC, the KOSMIK even supports HV servos. Different modes for sailplanes, motorplanes, helicopters, boats and RC cars (including back and forth drive) make the KOSMIK flexible for many applications. Apart from a second helicopter mode with fixed RPM a spool up optimized for scale helicopters is implemented. The scope of delivery includes tailor made motor and battery cables as well as one BEC cable. Optionally available are special KOSMIK heat sinks which guarantee the maximum power of this ESC.

    BEC
    One important feature of the KOSMIK is the strongest BEC KONTRONIK has ever developed. With a voltage from 5 V up to 8 V and a current capacity of 7 A continuous and up to 20 A peak the KOSMIK is the ESC for the most demanding tasks. Two BEC ports allow for using full current when using the second BEC cable.

    Screwed instead of soldered
    No wires. This is maybe the first thing you notice looking at the new KOSMIK. In order to handle the enormous power the KOSMIK is provided with gold tabs instead of the familiar soldered cables. Before usage cables and tabs are connected via screws and cable shoes. This concept makes exchanging cables easy and forms a reliable high current connection.

    Data interfaces
    Therefore the KOSMIK, in addition to three connectors for sensors and telemetry, provides a fast micro USB port in order to give out and process operation data.

    Mode-Programming
    The well-known and proven KONTRONIK Mode-Programming is also implemented in the KOSMIK. Thus, the ESC is rapidly deploy-able and can be customized for different applications within the shortest possible time.

    PROGDISC Compatible
    The KOSMIK can be parametrized using the KONTRONIK PROGDISC. This allows to change individual parameters and helps to adjust the KOSMIK to your personal preferences.

    Online Updatable
    Of course, the KOSMIK is also up-datable online. This allows software updates easily set at home. Long downtime caused by sending and waiting are a thing of the past.

    LED
    Equipped with two bi-colored LEDs the KOSMIK offers a wide range of signal outputs. These can be used for both diagnostic purposes, as well as for programming support.

    Logger
    As the first KONTRONIK ESC the KOSMIK offers the possibility of recording operating parameters internally. Internal recording delivers more detailed data than an external system could ever supply. With the high recording capacity and speed KONTRONIK delivers state-of-the-art technology.

    MicroSD Card
    All recorded data are written on a MicroSD card. This enables a flexible analysis of a great data volume.

    Specifications:

    • Cell count (LiPo): 5-14
    • Operating voltage [V]: 20-58
    • Continuous current [A]: 160
    • Maximum RPM with 2-pole-motor: 250,000
    • Size [mm] (without capacitor): 90x54x29
    • Weight [g] without cables: 200
    • BEC current continuous [A]: 7
    • BEC current maximum [A]: 20
    • BEC voltage adjustable [V]: 5-8
    • PWM frequency [kHz]: 8-32
    • Sensor ports: 3


    Features:

    • BEC short circuit protection
    • Auto Programming Mode
    • Stick positions programmable
    • Mode programming
    • PROGDISC ability
    • Online update ability (OUF)
    • RPM control
    • Auto-rotation mode
    • EMF brake can be adjusted*
    • Proportional brake
    • Short circuit protection
    • False start protection
    • Polarity protection
    • Current limiting
    • Over-temperature protection
    • Under-voltage cutoff
    • Can be disabled
    • with automatic adjustment for cell count: Li-Ion / LiPo / NiCd / NiMh /LiFePo
    • Variable cutoff voltage per cell *
    • Slow down instead of cutoff *
    • Active freewheeling circuit
    • LED status display
    • Overload alarm
    • Reversible rotation direction
    • Data logging
    • Anti spark
    • USB port
    SKU: KON-4816
    €599.00
    inc. VAT

     72HR STOCK
  • Kontronik Kosmik 200HV Brushless ESC

    Kontronik Kosmik 200HV Brushless ESC

    This is the Kontronik Kosmik 200 HV Brushless ESC. The KOSMIK delivers incredible power for ambitious pilots with the KONTRONIK reliability you have come to trust. With the ability to deliver 200A of continuous current with 5S to 14S LiPo setups, the KOSMIK can easily push any high power model into motion. With its integrated and adjustable BEC, the KOSMIK even supports HV servos! Different modes for sailplanes, airplanes, helicopters, boats and RC cars (including forward and reverse drive) make the KOSMIK flexible for a variety of applications. Two helicopter modes include a fixed RPM function, as well as a spool up optimized for scale helicopters and tailor made motor and battery cables as well as one BEC cable round out the package. The continuous current is setup for a maximum battery capacity of 10,000mAh, and optional special KOSMIK heat sinks are available to help guarantee the maximum power and reliability of this ESC.

    >BEC: The strongest BEC KONTRONIK has ever developed. With a voltage from 5V up to 8V and a current capacity of 7A continuous and up to 20A peak the KOSMIK is the ESC for the most demanding tasks. Two BEC ports allow for using full current when using the second BEC cable.
    >Screwed instead of soldered: No wires. This is the first thing you notice looking at the KOSMIK. In order to handle the enormous power, the KOSMIK is provided with gold tabs instead of the familiar soldered cables. Before usage cables and tabs are connected via screws and cable shoes. This concept makes exchanging cables easy and provides a reliable high current connection.
    >Data interfaces: In addition to three connectors for sensors and telemetry, the KOSMIK features a micro USB port to quickly deliver and process operation data.
    Mode-Programming: The well-known and proven KONTRONIK Mode-Programming is also implemented in the KOSMIK. The ESC is can be customized for different applications in a short amount of time.
    >PROGDISC Compatible: The KOSMIK can be parameterized using the KONTRONIK PROGDISC. This allows the user to change individual parameters and helps to adjust the KOSMIK to your personal preferences.
    Online Updatable: The KOSMIK can be updated online. This allows software updates to be done easily at home. Long downtimes caused by sending and waiting are a thing of the past.
    >LED: Equipped with two bi-colored LEDs the KOSMIK offers a wide range of signal outputs. These can be used for both diagnostic purposes, as well as for programming support.
    >Logger: The KOSMIK offers the ability to record operating parameters internally. Internal recording delivers more detailed data than an external system could ever supply. With the high recording capacity and speed KONTRONIK delivers state-of-the-art technology.
    >MicroSD Card: All recorded data is written on a MicroSD card. This enables a flexible analysis of data.

    Features:

    •   BEC short circuit protection
    •   Auto Programming Mode
    •   Stick positions programmable
    •   Mode programming
    •   PROGDISC ability
    •   Online update ability (OUF)
    •   RPM control
    •   Autorotation mode
    •   EMF brake can be adjusted*
    •   Proportional brake
    •   Short circuit protection
    •   False start protection
    •   Polarity protection
    •   Current limiting
    •   Over temperature protection
    •   Under voltage cutoff
    •   Can be disabled
    •   with automatic adjustment for cell count: Li-Ion / LiPo / NiCd / NiMh /LiFePo
    •   Variable cutoff voltage per cell *
    •   Slow down instead of cutoff *
    •   Active freewheeling circuit
    •   LED status display
    •   Overload alarm
    •   Reversible rotation direction
    •   Data logging
    •   Anti spark
    •   USB port

    Specifications:

    • Cell count (LiPo): 5-14
    • Operating voltage [V]: 20-58
    • Continuous current [A]: 200
    • Maximum RPM with 2-pole-motor: 250,000
    • Size [mm] (without capacitor): 90x54x29
    • Weight [g] without cables: 200
    • BEC current continuous [A]: 7
    • BEC current maximum [A]: 20
    • BEC voltage adjustable [V]: 5-8
    • PWM frequency [kHz]: 8-32
    • Sensor ports: 3
    SKU: KON-4820
    €699.00
    inc. VAT

     72HR STOCK
  • KOSMIK Bluetooth Module

    KOSMIK Bluetooth Module

    Communicator App

    The KONTRONIK Communicator App will allow you to wirelessly program your  KOSMIK via your phone or tablet. In addition  to programming, the Communicator App will allow you view live stream data from your KOSMIK as long as you remain in  Bluetooth range.

    The Bluetooth module is available, and  must be used if you wish to create a wireless  connection with the KOSMIK.

    KONTRONIK now offers a KOSMIK Bluetooth Module. This allows the KOSMIK to communicate with your smart phone or tablet computer.

    SKU: KON-9730
    €79.00
    inc. VAT

     72HR STOCK
  • Low Voltage Display LED Board

    Low Voltage Display LED Board

    Optional part for GVR-7020 Gryphon Extreme-Heli Voltage Regulator. Plugs into the AUX position on the regulator.

    Red LED's illuminate when a low-voltage condition is met. Low-voltage condition is user-selectable for LiFe or LiPo at the Voltage Regulator.

    SKU: GDB-1010
    €7.90
    inc. VAT

     IN STOCK

Manufacturers

Back