Accessories

Accessories

Accessories for Canopies and Fuselages

Products


  • Agile  5.5 /7.2 Quick Release Canopy Mounts

    Agile 5.5 /7.2 Quick Release Canopy Mounts

    Quick Release Canopy Mounts for the Agile  5.5 /7.2

    Includes:

    4-Quick Release Pins
    4-Quick Release Standoffs
    4-Grommets
    Front Standoff length 27.18mm/1.070 in w/ M3 mounting thread
    Rear Standoff Length 11mm/.433in w/ M3 mounting thread

    SKU: A72QRCM
    €43.99
    inc. VAT

  • BELL 222 retracts

    BELL 222 retracts

    This retractable undercarriage kit has been developed specifically for the Bell 222 and Airwolf fuselage kit.
    The tricycle undercarriage is operated by a single or double central servo, and the retract units lock mechanically at both end-points.

    This set fit 30-60 size fuselages, Rubber Wheels Not included ( Original from the kit should be used)

    SKU: SKU9107
    €79.00
    inc. VAT

     LOW STOCK
  • Booya Tuff Canopy Grommets

    Booya Tuff Canopy Grommets

    Picture
    Designed for the serious 3D pilot who demands a failproof grommet system that can withstand hundreds of flights without having to worry about canopy grommet failure.

    This 3pc system is made to work with on any Nitro Helicopter that uses the RCBooya Quick Release Canopy Mount and has a option to enlarge the canopy holes to 7/16 diameter.
    IMPORTANT
    Made for use with canopies that measure 1mm in thickness

    Kit Includes

    4- Booya Tuff ™ Snap Grommets
    4- Fuel Proof VITON ™ O-Rings

    Installation Instructions

    Enlarge the canopy grommet holes to 7/16 diameter
    Take apart the two halves of the grommet
    Place CA onto the grommet area that comes into contact with the canopy
    Install into canopy,white recess on the outside of the canopy,0-ring to the inside of the canopy
    Snap the two halves togather and allow CA to setup
    Install Quick Release Pin into Booya Tuff ™ Grommet
    ENJOY !
    SKU: BTCG
    €7.99
    inc. VAT

     IN STOCK
  • Canopy Clips (10pcs)

    Canopy Clips (10pcs)

    Canopy Clips 10pcs

    SKU: MIK-5116
    €6.90
    inc. VAT

     LOW STOCK
  • Canopy Egde protection U channerl Rubber strip, 1m

    Canopy Egde protection U channerl Rubber strip, 1m

    Protect your canopy edges, or use it as wire protection against carbon frames, use it combined with fuel tanks.. and much more.
    this Strip including U shape EPDM. the profile is U shape and its 1.2mm wall thick, fits perfectly 1-2 mm frames.
    See images for exact dimensions and sizes.

     

    SKU: Urub
    €3.00
    inc. VAT

     IN STOCK
  • Canopy Egde protection U channerl Rubber strip,Round 1m

    Canopy Egde protection U channerl Rubber strip,Round 1m

    Protect your canopy edges, or use it as wire protection against carbon frames, use it combined with fuel tanks.. and much more.
    this Strip including round U shape EPDM. the profile is U shape and its 5.5mm diameter, with cut to fit perfectly 1-2 mm frames.
    See images for exact dimensions and sizes.

     

    SKU: Urub1
    €3.00
    inc. VAT

     IN STOCK
  • Compass 3D Plus Canopy Mounts

    Compass 3D Plus Canopy Mounts

    Compass 3D Plus Quick Release Canopy mount features a custom locking push/pull pin design made to fit the rear 2 mounts on your Compass 3D Plus or 6HV Helicopter. Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy. Standoff is made from 6061-T6 aluminum Hardcoat Surface Treatment Dyed Black M3 Install Hole Standoff Length 1.270in/32.25mm Kit is designed for use with the stock Compass 3D Plus canopy Use of any other canopy may affect the intended performance of this kit Kit includes: 2-Quick Release Pins 2-Quick Release Standoffs 2-Viton Fuel Resistant O-Rings 2-Fuel Resistant Anti Vibration Pads w/ 3M™ Adhesive (peel and stick)

    SKU: C3DPQRCM
    €18.99
    inc. VAT

  • Compass 6HV Canopy Mounts

    Compass 6HV Canopy Mounts

    Compass 3D Plus Quick Release Canopy mount features a custom locking push/pull pin design made to fit the rear 2 mounts on your Compass 3D Plus or 6HV Helicopter.

    Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy.

    Standoff is made from 6061-T6 aluminum
    Hardcoat Surface Treatment
    Dyed Black
    M3 Install Hole
    Standoff Length 1.270in/32.25mm

    Kit is designed for use with the stock Compass 3D Plus canopy
    Use of any other canopy may affect the intended performance of this kit

    Kit includes:

    2-Quick Release Pins
    2-Quick Release Standoffs
    2-Viton Fuel Resistant O-Rings
    2-Fuel Resistant Anti Vibration Pads w/ 3M™ Adhesive (peel and stick)
    SKU: C6HVQRCM
    €18.99
    inc. VAT

     LOW STOCK
  • Compass 7HV Canopy Mounts

    Compass 7HV Canopy Mounts

    Compass 7HV Quick Release Canopy mounts features a custom locking push/pull pin design made to fit the Compass 7HV helicopter.

    Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy.

    • Standoff is made from 6061-T6 aluminum
    • Hardcoat Surface Treatment
    • Dyed Black
    • Standoff Length: 33.78 mm w/M3 thread

    Kit is designed for use with the stock Compass 7HV  Canopy.
    Use of any other canopy may affect the intended performance of this kit.

    Kit includes:

    • 2-Quick Release Pins
    • 2-Quick Release Standoffs
    • 4-Grommets
    SKU: C7HVQRCM
    €18.99
    inc. VAT

  • Compass Atom 500 R Canopy Mounts

    Compass Atom 500 R Canopy Mounts

    RCBooya Atom 500/500R Quick Release Canopy mount features a custom locking push/pull pin design made to fit the rear 2 mounts on your Compass Atom Electric Helicopter.

    Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy.

    Standoff is made from 6061-T6 aluminum
    Hardcoat Surface Treatment
    Dyed Black
    M3 install thread
    Standoff Length .840in/21.336mm

    Kit is designed for use with the stock Compass Atom 500/500R canopy
    Use of any other canopy may affect the intended performance of this kit

    Kit includes:

    2-Quick Release Pins
    2-Quick Release Standoffs
    4-Fuel Resistant Viton™ O-Rings
    SKU: CA5RQRCM
    €18.99
    inc. VAT

  • Edge 'U' Protector Transparent Rubber (1m)

    Edge 'U' Protector Transparent Rubber (1m)

    Edge 'U' protector transparent rubber (1 M)

    For carbon sheets from 1.0mm - 2.0mm.

    SKU: MIK-04900
    €5.50
    inc. VAT

     72HR STOCK
  • Edge protector, 1 Meter

    Edge protector, 1 Meter

    Edge protector for carbon sheets from 1.0mm - 2.0mm.

    SKU: MIK-4594
    €4.50
    inc. VAT

     72HR STOCK
  • Gaui X7 Quick Release Canopy Mounts

    Gaui X7 Quick Release Canopy Mounts

    Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy.

    • Standoffs are made from 6061-T6 aluminum
    • Hardcoat Surface Treatment
    • Dyed Black
    • M3 mounting thread
    • Standoff Length 2.050 in/52.07mm   

    Kit is designed for use with the stock Gaui canopy.
    Use of any other canopy may affect the intended performance of this kit

     Kit includes:

    • 4-Quick Release Pins
    • 4-Quick Release Standoffs
    • 4-M3x.05x10 set screws
    • 4-Grommets.
    SKU: GX7QRCM
    €44.00
    inc. VAT

     LOW STOCK
  • Goblin 380/420 MAGNETIC QUICK RELEASE CANOPY SET

    Goblin 380/420 MAGNETIC QUICK RELEASE CANOPY SET

    Goblin 380/420 MAGNETIC QUICK RELEASE CANOPY SET

    Expedites the installation and removal of the canopy

    Includes:
     

    • Canopy possition x 2pcs
    • Magnet Canopy Pin x 2pcs

    Use for:

    Goblin 380/420
     

    SKU: H0562-S
    €21.00
    inc. VAT

     LOW STOCK
  • Logo 700 Quick Release Canopy Mounts

    Logo 700 Quick Release Canopy Mounts

    RCBooya Mikado Logo 700 XXtreme Quick Release Release Canopy mount features a
    custom locking push/pull pin design made to fit the Logo 700
    Helicopter.

    -Quick Release pin is made from all stainless steel components
    -Standoff is made from 6061-T6 aluminum
    -Hardcoat Surface Treatment
    -Dyed  Black
    -Standoff
    -Length 1.270in/ 32.26mm w/M3  mounting thread


    Kit is
    designed for use with the stock Logo canopy.
    Use of any other canopy may affect the intended performance of this kit
     
    Kit includes:
    2-Quick Release Pins
    2-Quick Release Standoffs
    4-Grommets

    *NOTE: Use of this kit requires you to  increase the canopy mounting holes on your canopy  to 11/32 diameter
      to install the supplied canopy grommets.

    SKU: L7XQRCM
    €22.99
    inc. VAT

  • Magnetic Canopy Mount Black

    Magnetic Canopy Mount Black

    Magnetic Canopy Mount in Black

    SKU: TXF061-BK
    €6.00
    inc. VAT

  • O-Rings For Quick Release

    O-Rings For Quick Release

    8x Viton O-Rings For Quick Release Pin
    SKU: ROR
    €3.99
    inc. VAT

  • Raptor E700 Quick Release Canopy Mount

    Raptor E700 Quick Release Canopy Mount

    RC Booya Raptor E700 Quick Release Canopy Mount RE74QRCM

    Quick Release Canopy mount features a custom locking push/pull pin design

    made to fit your Raptor E700 helicopter.

    -Quick Release pin is made from all stainless steel components -Standoff is made from 6061-T6 aluminum
    -Hardcoat Surface Treatment
    -Dyed Black
    -Standoff Length 22.6mm/.89 in w/M3 thread

    Kit is designed for use with the stock Raptor E 700 Canopy

    Use of any other canopy may affect the intended performance of this kit

    SKU: RE74QRCM
    €39.99
    inc. VAT

     LOW STOCK
  • RCBooya Replacement Grommets

    RCBooya Replacement Grommets

    RCBooya Replacement Grommets

    4- Fuel Resistant Grommets
    SKU: RG
    €3.99
    inc. VAT

  • Replacement Anti Vibration Pads

    Replacement Anti Vibration Pads

    4- Fuel Resistant Anti Vibration Pads w/3M™ Adhesive Heli Team Tip: To protect the adhesive from fuel add a band of CA around the outside of the anti vibration pad. WORKS GREAT !

    SKU: RAVP
    €3.99
    inc. VAT

     IN STOCK
  • T-Rex 500 Quick Release Canopy Mount

    T-Rex 500 Quick Release Canopy Mount

    RCBooya 500 Electric Quick Release Canopy mount features a custom locking push/pull pin design made to fit the Align 500 Electric Helicopter. Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy. Standoff is made from 6061-T6 aluminum -Hardcoat surface treatment -Dyed Black Kit is designed for use with the stock Align V1 style canopy. Use of any other canopy may affect the intended performance of this kit Kit includes: 2-Quick Release Pins 2-Quick Release Standoffs .84in/21.34mm length w/M2.5 thread 4-Grommets *NOTE: Use of this kit requires you to increase the canopy mounting holes on your canopy to 11/32 diameter to install the grommets.

    SKU: 5QRCM
    €18.99
    inc. VAT

  • T-Rex 550 Quick Release Canopy Mount

    T-Rex 550 Quick Release Canopy Mount

    RCBooya 550 Electric Quick Release Canopy mount features a custom locking push/pull pin design made to fit the Align 550 Electric Helicopter.
    Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy.
    Standoff is made from 6061-T6 aluminum Hardcoat Surface Treatment Dyed Black Standoff Length 1.068in/27.12mm w/M3 thread Kit is designed for use with the stock Align V1 style canopy.
    Use of any other canopy may affect the intended performance of this kit Kit includes:
    2-Quick Release Pins 2-Quick Release Standoffs 4-Grommets *NOTE: Use of this kit requires you to increase the canopy mounting holes on your canopy to 11/32 diameter to install the grommets.

    SKU: 55QRCM
    €18.99
    inc. VAT

  • T-Rex 600 E PRO Quick Release Canopy Mounts

    T-Rex 600 E PRO Quick Release Canopy Mounts

    RCBooya 600 E PRO Quick Release Canopy mount features a custom locking push/pull pin design made to fit the Align 600 E PRO Helicopter.

    Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy.

    Standoff is made from 6061-T6 aluminum
    Hardcoat Surface Treatment
    Dyed Black
    Standoff Length .700in/17.78mm w/M3 thread

    Kit includes:

    4-Quick Release Pins
    4-Quick Release Standoffs
    4-Grommets
    4-M3x12 Set Screws

    SKU: 6EP4QRCM
    €37.99
    inc. VAT

  • T-Rex 600 Quick Release Canopy Mount

    T-Rex 600 Quick Release Canopy Mount

    RCBooya 600 Electric Quick Release Canopy mount features a custom locking push/pull pin design made to fit the Align 600 Electric and ESP Helicopters. Quick Release pin is made from carbon steel, bright zinc plated with stainless steel components and is designed to stay connected to the canopy. Standoff is made from 6061-T6 aluminum Hardcoat Surface Treatment Dyed Black Standoff Length 1.270in/32.25mm w/M3 thread Kit is designed for use with the stock Align V1 style canopy. Use of any other canopy may affect the intended performance of the kit. Kit includes: 2-Quick Release Pins 2-Quick Release Standoffs 4-Grommets *NOTE: Use of this kit requires you to increase the canopy mounting holes on your canopy to 11/32 diameter to install the grommets.

    SKU: 6EQRCM
    €18.99
    inc. VAT


Manufacturers

Back