Europe based Mega-Store of RC Helicopters, Drones, Planes

eRCMarket is a Belgium based superstore for all your remote control helicopters, drones, cars and airplane needs. We also stock a huge range of parts, tools and accessories. With over 40 years experience in R/C, UAV and UAS, we have been serving customers all over the world for over 20 years.

New Arrivals

Cable - Fuel line Mounting Clamps pack of 10 for fuel line or wires up to 5mm

Cable - Fuel line Mounting Clamps pack of 10 for fuel line or wires up to 5mm

Cable - Fuel line Mounting Clamps pack of 10 for fuel line or wires up to 5mm
Diameter of 7mm allows to pass safely silicone line/tygon or some wiring

Arrange your cabling nicely across the helicopter
Including a Pack of 10

€6.00

Inc. VAT
Quantity
Futaba T6K Black G10 Transmitter Tray

Futaba T6K Black G10 Transmitter Tray

Futaba T6K G10 Transmitter Tray

Very stable transmitter tray in the modern carbon stainless steel design.
The transmitter tray is made ​​of high quality 2mm thick carbon material with stainless steel frames.
The transmitter tray can be transported in any commercially available aluminum case.

Specification:

    Dimensions:  Width: 295 mm
    Depth without transmitter: 150 mm
    Height with standard transmitter stand: 138 mm
    Height with folding transmitter panel bracket: 168 mm / folded: 113 mm
  • Transmitter tray without transmitter without FPV & without rubber hand rest pads.

€69.00

Inc. VAT
Quantity
Titanium Hand made Push-Rod M3, different lengths possible, Made per order

Titanium Hand made Push-Rod M3, different lengths possible, Made per order

We offer hand made pushrods from TITANIUM Grade Medical 3, this is one of the best Titanium materials (produced in europe) you can buy.
the Tread is made by Push technology and not Cut, means there is no weak point at the point where the tread is stopped (different from cut where the point becomes a breaking point)

We use Medical grade 3 Road, and we are able to produce tread per needs. you can contact us for special lengths/treads, in general we can make push-rods up to any length, and treads up to 20mm each side.
Some standard sizes are here, but for custom products- contact us

price is per set of 2 pushrods.

€12.00

Inc. VAT
Quantity
MAH UAV Large scale Helicopter Tri-pal rotor Blades 950mm-set of 3

MAH UAV Large scale Helicopter Tri-pal rotor Blades 950mm-set of 3

These are the original MAH dual taper series main rotor blade. Not only That the blade's chord gradually tapered, but the airfoil is also tapered thinner towards the blade tip. This yields a high performance blade suitable for 3D flying.

Those blades were designed for Military use, especially made to carry a heavy lift without flex.
Main fit is for 1.8+ helicopters, Jet Turbines Helicopters, and UAV applications The main blades are made from the highest quality CF and are used by pro flyers around the world.
MAH blades are balanced & shipped with proper CG for the absolute best performance.  And chosen by leading pilots worldwide, and many reputable UAV producers.

Full symmetrical Carbon main blade for helis.

MAH UAV Large scale Helicopter Tri-pal rotor Blades 950mm-set of 3

  • Length 950mm
  • Root :14mm
  • Width: 90(root)-75(tip)
  • Weight : +-360grm

€390.00

Inc. VAT
Mikado VBar EVO Aluminium-case VLink 7.x Express, See colors

Mikado VBar EVO Aluminium-case VLink 7.x Express, See colors

Mikado VBar EVO Aluminium-case VLink 7.x Express, See colors in option

New processor: 500 MHz (NEO: 98 MHz), more memory, FPU, highest available computing power on the market to this date
Innovative step-up/step-down voltage supply from 2 V up to 16 V at full power with high efficiency (less excess heat)
Full telemetry and range down to 2 V supply voltage
Improved high frequency technology for high power and sensitivity
Double sensor system using tried and tested technology and new sensors
The hardware allows for new specs:
Frame rates adjustable up to 1 kHz (1 ms) on the swash plate and 0.5 ms on the tail
ESC frame rate up to 1 KHz
Pulse width selecable between 1.5 ms down to 125 µS as well as digital high speed protocols
Improved algorithms: adjusted tot he new frame rates, new optimized digital filtering
Dynamic swash plate rotation (per bank)
New „Tail Torque Extension“ for motor driven tails, more control when the tail rotor is unloaded

€279.00

Inc. VAT
Quantity
Mikado VBar RX-Only, 7 channel receiver #5560

Mikado VBar RX-Only, 7 channel receiver #5560

VBar RX-Only, 7 channel receiver.
Not upgrade-able (can not be updated to Pro/Pro+Rescue, can not be used with gyro sensors).

€69.00

Inc. VAT
Quantity
ULTIMATE Straight Micro Hemostat Stainless steel 13cm

ULTIMATE Straight Micro Hemostat Stainless steel 13cm

Best quality hemostat with high polish finish and tough serrated jaws. Imported from Japan.

These items have many uses in a lab, a shop or at home, holding or clamping small or hot items, or reaching into tight places. They can be used for assembly and manufacturing or repair work of many kinds.

A simple tool with small needle-nose jaws that lock closed with a ratchet on the handle end. Use it to pick up and hold small items, clamp parts together for gluing, or as a handy heat sink when soldering.
Made of stainless steel with semi-polished finish, all feature box joint, serrated jaws and rachet lock to ensure a secure hold.

Lenght- approx 13cm

€6.50

Inc. VAT
Quantity
Scorpion HK-45 series Motor Bearing Kit set

Scorpion HK-45 series Motor Bearing Kit set

In order to keep your motor in top running condition, you need a good set of bearings. Occasionally, after a crash or landing in the dirt, the bearings can become damaged and need to be replaced. The Scorpion HK-45mm Motor Bearing Kit includes a pair of original equipment replacement bearings to fit the Scorpion HK-45 Series motors. (except HK-4526)

Please note, the bearings are an exact fit into the motor housings, so they do fit snugly. When removing the old bearings, you may need to gently tap them out. However, when installing the new bearings, do not tap them in with anything, as this can dent the ball races and ruin the bearings. When installing ball bearings they need to be pressed in by the outer part of the race. Never apply pressure to the inner race, as this can damage the bearing and lead to premature failure.

€10.50

Inc. VAT
Quantity

Featured Products

TBS Crossfire Micro TX V2 STARTER Set Long range,Low Latency

TBS Crossfire Micro TX V2 STARTER Set Long range,Low Latency

The TBS CROSSFIRE is a long range R/C link based on the newest RF technology, capable of self-healing two-way communications and range beyond comprehension. With a sensitivity of -130dB, full RF-side diversity, tiny receivers for FPV quads, the TBS CROSSFIRE contains the most modern technology to provide a superior long range control link

The Crossfire Micro TX borrows the core technology from its larger brother, but is a JR-module transmitter simplified to the most sought-after features, at a killer price! For people looking to do extreme long range flights beyond 15-20km, the Crossfire TX is still the way to go. For anyone looking to penetrate buildings, fly mini quads or just explore your surroundings a few kilometers away, the Micro TX is the perfect companion. It will still go out up to 40km, just like its bigger brother. But it costs less than half the price.

 Features:

  •     Long range, adaptive and robust remote control system for your aircraft
  •     Immune to on-board noise
  •     Two-way communication link with real-time link vitals and telemetry
  •     Self-healing & frequency hopping (DSSS, FHSS)
  •     Adaptive bandwidth control and range optimization
  •     RX beacon mode to recover your downed aircraft
  •     Super easy binding and configuration via built-in display of your R/C
  •     Low latency, 150Hz update rate (3x faster than typical RC links) control for perfect immersive feeling
  •     Two receiver models: 8 port Diversity Rx, 4 port Mini-receiver (4g weight!)
  •     8 or 12ch output via SBUS/PPM/CRSF on both receivers
  •     Ability to fly with multiple friends at the same time (10 or more)
  •     Selectable RF power from 25mW to 250mW (local restrictions apply)
  •     Transmitter LED shows link health
  •     Micro-receiver for smaller drones. Smaller than you think!
  •     Software updates via RF Link

 
Technical specifications:

  •     Frequency Band: 868MHz- EU
  •     Input Voltage: 6.0 - 13V
  •     Connector : USB-C
  •     Power consumption: 1.1W (@10mW) - 2W (@100mW)
  •     Dimensions: 65 x 48 x 22 mm (JR module size)
  •     Weight: 48g

Package includes

  • 1 x TBS Crossfire Micro TX V2
  • 3 x TBS Crossfire Nano RX
  • 3 x TBS Crossfire Micro Receiver Antenna
  • 3 x TBS Crossfire Immortal T V2 Antenna
  • 1 x Taranis QX7 Mod
  • 3 x Cables and Shrink Tubes set

€199.99

Inc. VAT
Quantity
UAVsystems Fireproof LiPo carry and storage Safe Bag for 12s-14s 340mm long

UAVsystems Fireproof LiPo carry and storage Safe Bag for 12s-14s 340mm long

The LiPo Safe sack/bag is a hi-tech bag made of space-age materials that has the ability to contain a lithium polymer battery fire or charging mishap. Place your lithium polymer battery inside the LiPo Safe and extend the charging wires through the top flap. Charge the lipo batteries when they’re in the LiPo Safe for peace of mind and greater safety. In the case of a lithium polymer battery charging mishap, the LiPo Safe’s fire-resistant material mitigates the ferocity of the LiPoly blaze inside and vents the smoke outside the LiPo Safe.

This is a long version of the Safe product, measuring internal dimensions of 340x70x65mm, fits long Stick Lipos 12s and even some 14S packs- verify the size of your lipo to be sure it fits inside the bag.

The LiPo Safe is sealed with a thick, industrial strength, Velcro flap. The current LiPo Safe is designed to handle a lithium polymer battery mishap

Before using the LiPo Safe you must read and understand the LiPo Safe Safety Instructions. We assume absolutely no liability for any damages of any kind - even with proper use. When using the LiPo Safe, you must always remember to abide by safe lithium polymer battery charging and safety rules and never leave charging li-polymer batteries unattended. Never leave damaged lipos unattended. Always use the LiPo Safe on a non-flammable surface and in a ventilated area. Avoid damage to the LiPo Safe and not use the LiPo Safe if it is damaged.

Instructions to use:

Ensure that charger rate is properly set and polarity is correct

  1. Attach charging leads to battery
  2. Place battery in LiPo Safe towards the bottom
  3. Place LiPo Safe on non-flammable surface
  4. Route charge leads through vent at the top seam of the LiPo Safe
  5. Close top flap of LiPo Safe and press hook and loop closure fully closed
  6. Charge battery using proper charging practices
  7. Always practice extreme caution when charging and never leave a charging battery unattended

Please check the Video showing the use of Lipo Safe

€14.99

Inc. VAT
Quantity
RCPROPLUS REB 6808 Pro D6 P8 TWIN SQUARE SUPRA-X REB6808 PRO D6 6mm Bullet Connector 8 Pairs

RCPROPLUS REB 6808 Pro D6 P8 TWIN SQUARE SUPRA-X REB6808 PRO D6 6mm Bullet Connector 8 Pairs

This is a pack of 8 RCPROPLUS SUPRA-X REB6808 PRO D6 6mm Bullet Connector

Set including 8 PAIRS.


Featuring a unique patented banana plug lock design, these Pro-D6 connectors securely lock in place handling quick movements and vibrations, commonly found during extreme 3D flights, without coming apart. The stronger jacket and snaps extends the advantages of the previous generation of Supra X Connectors and makes them better.

These connectors are a great solution for your high current and high voltage demands offering a large, low resistance surface patch for efficient power transfer. The 24K Gold Plated bullet plugs feature a recessed wire cavity and solder windows making assembly hassle free, while the sheath uses high temperature capable, impact-resistant plastic imported from Japan.

Cover material:IDEMITSU plastic
Banana connector diameter:6mm
Suggested Wires:8AWG-10AWG
Capacity (Continuous):200A
Capacity (Burst):240A
Banana connector material:Class A Cooper C54 Series
Plating:24K Gold / Flash

Features:
Connection between battery and ESC
Can be used for 4 batteries and 4 ESCs (or 4 charger cables)

Package Included:
4 x Set
8 x 6mm Female& Male Bullet Connector

€35.90

Inc. VAT
FPV x230 Racer With Gimbal ,1080P Wide Angle HD Camera RC Quadcopter RTF

FPV x230 Racer With Gimbal ,1080P Wide Angle HD Camera RC Quadcopter RTF

FPV x230 Racer With Gimble,1080P Wide Angle HD Camera RC Quadcopter RTF

  • Built-in 120° wide angle and 1920 x 1080P HD camera to get the high quality shooting;
  • Equipped with 2200mAh smart flight battery.
  • Flip 360° steadily;
  • Real-time transmission for FPV action video.

Remote control:

  • Built-in video transmitter to improve the transmission quality and reliability of communication;
  • Equipped with camera and operation button to control easily.

Package Included:

  • 1 x X230 Multicopter
  • 1 x Battery
  • 2 x ABS 5030 propeller
  • 1 x Balance charger
  • 1 x Charger cable
  • 1 x Adapter
  • 1 x 4 pins connection wire
  • 1 x Screw bag

€359.00

Inc. VAT
Quantity
ZD-937/B/ESD Digital regulated Soldering Station, pre-selection buttons

ZD-937/B/ESD Digital regulated Soldering Station, pre-selection buttons

Soldering Station ZD-937, black, 150°C - 450°C, 48W,ESD-protection, with pre-selection buttons 100, 200, 300°C.

The station is ideal for home elektronics, school, workshop, service, production and lab.

Among the easy and quick temperature adjustment with the up-/down-buttons in 1°C- and 10°C-steps, it is possible to pre-select 100°C, 200°C and 300°C with the related button.

  • Compact, solid and insulated housing.
  • Station and soldering iron pod are arrangeable seperately.
  • Complete with soldering iron pod and soldering sponge.
  • LCD display with ilumination shows must- and actual value.
  • Energy display
  • 3 pre-selectionable fixed temperatures
  • Electronical sensor
  • Temperature controll
  • Short heating-up time thanks to its generous designed power supply
  • Powerful 48W soldering iron for a wide range of application
  • Temperature adjustment with buttons from 150 to 450°C, 1°C and 10°C steps
  • Optical and accoustic error message in case of malfunction
  • ESD protection

Technical Specification:

  • Input Voltage: 230V (220-240V), 50 Hz
  • Power of soldering iron: 48W
  • Fuse: T 1A/250V
  • 150°C-450°C temperature adjustment with 1°C- and 10°C-steps
  • Display accuracy: 5%
  • LC-Display with 3 1/2 digits
  • Dimension WxHxD: 210x125x135mm
  • Weight 1,8kg

Delivery:

  • Soldering station ZD-937
  • Soldering iron pod with drawer and soldering sponge
  • Soldering iron with tip 1,6 mm
  • German and english manual

€59.90

Inc. VAT
Quantity
10 Piece Combination Spanner Set 4-11mm

10 Piece Combination Spanner Set 4-11mm

This "economy" spanner set includes just about all the sizes you will ever need on a model heli.
Ideal for you field box and building bench.

Sizes included are : 4mm, 4.5mm, 5mm, 5.5mm, 6mm, 7mm, 8mm, 9mm, 10mm, 11mm.
Set of 10 spanners

€24.00

Inc. VAT
Quantity
Custom assembled TITAN DC5 HD v1.4 Compatible with DJI Air Unit PNP

Custom assembled TITAN DC5 HD v1.4 Compatible with DJI Air Unit PNP

TITAN DC5 w/ DJI Air Unit BNF built for  the amazing new DJI FPV system, this quad makes flying FPV truly breathtaking. With the 720p video shown at 120fps through the goggles, DJI has set the bar at a new high for clarity and image quality in an FPV system. This TITAN DC5 BNF is 5 inch quad which is no prop in view, equipped SucceX-D F7(50A 4-in-1 ESC) Stack and popular XING motor, everything you just need to bind and fly!

This model can accept up to 6s, but the motors mounted are designed to be used with 4S.

    You can use Any radio you want, you will need to add your receiver and bind and calibrate it.

    If you use your own DJI Remote Controller, you need to update beta-flight to 10.6.0 to set up and bind your DJI remote controller.

    ELECTRONICS // SucceX-D F7 Stack (50A 4-in-1 ESC):

    • Universal USB Type C connector instead of micro USB
    • Plug-and-Play. No need to solder tiny wires
    • Designed to support DJI Digital FPV.

    BNF // Parts lists

    • 1x TITAN DC5 HD Frame
    • 2x TPU camera side plate soft mount
    • 1x iFlight Lipo Strap
    • 2x Nazgul 5140 Propeller (Set of 4 - Color May Vary)
    • 4x XING 2207 Motor Unibell (4S 2450KV)
    • 1x SucceX- F7 Flight Controller
    • 1x SucceX BLHeli32 50A 4-in-1 ESC 2-6S

    €330.00

    Inc. VAT
    Quantity
    Sky hero Anakin Club FPV racer 215-5’’ ARF combo w.radio

    Sky hero Anakin Club FPV racer 215-5’’ ARF combo w.radio

    Sky hero Anakin Club FPV racer 215mm -5"’’ ARF combo, Our combo delivered with Best components we beleive are on the market today. We beleive that quality assembly can be done by customer, there are a lot of advantages to do so.
    See the specs below.

    • Anakin club racer Frame kit Xnova 2204-2300Kv motors, esc, props- Included and factory preinstalled.
         Note: if you choose other motors, you will need to assemble the kit yourself, you will receive all components, but not ARF version.
    • CC3D Metal Case controller included
    • PDB-Bec
    • FPV Camera included
    • RADIO link AT9 with receiver Sky hero version (white edition )

    Not included:

    • Lipo charger
    • Battery 3s 1300-1500 mah
    • VTX - optional

    Sky hero did it again, with the latest drone technology, you have the possibility to fly the freedom of birds.
    With competition racing and performance within the DNA of SKY HERO, this machine was created as serious racer for those who want the best.
    Club-racer- inherits the amazing design of the original sky hero Anakin, with new evolved concept.
    Strengthened with flat arms.
    this was developed with the vision that FPV racers deserve a near-indestructible machine, agile racer they can trust.
    Locked in trajectories and customizable.

    General specs of Club racer versions.

    • Full carbon frame- Crash resistant.
    • Innovative abutted A frame design.
    • Minimized vibrations distribution, Optimized shock absorption
    • 3K 4mm Carbon
    • Sandwitched frame plates
    • Fully protected electronics
    • Optimized Shape, size and frame thickness, delivering outstanding strength-to weight ratio
    • Responsiveness- so rigid, that you feel "At one" with your frame.

    ESSENTIALS

    •     Entirely designed for racing
    •     Flat arms conception for highest impact resistance
    •     Simplified option for easy components replacement
    •     Low drag, for higher speeds
    •     Electronics fully protected

    KEY FACTORS

    •     Premium choice for FPV
    •     High wind resistance
    •     Super fast
    €359.00

    €229.00

    36% Off Inc. VAT
    Quantity

    10K+ Products In Stock

    Real-Time Stock Levels


    Competitive Prices

    Earn Points, Secure Payments



    Top Customer Service

    Supported by Real Enthusiasts

    We're a team of certified engineers with 40 years experience in R/C, UAV and UAS.

    Our excellence is in our customer service. Our value stands in understanding what we sell.

    We have a real store in Belgium. We are there for you and accessible.

    Give us a try, you can be confident to get a real advice from modeler to modeler.

    Beginner or Expert, B2B and B2C, we're happy to serve you. Your passion is our passion!