TX Modules

TX Modules

Futaba TM-14 2.4 GHz FASST Module

Futaba TM-14 2.4 GHz FASST Module

12 / 14-channel RF module for converting robbe/Futaba transmitters fitted with the MZ-FM RF module, such as the T12Z, T12FG and T14MZ.

This module was Installed on radio, but very low time of work

The latest practical tests confirm the long range of the Futaba FASST system:
Ground – ground: more than 2000 meters range ! (receiver at 1.5 meters above ground, visual contact)
Ground – air: more than 3000 meters range ! (with visual contact to receiver)

This product is suitable for European region

  • 2.4GHz Spread Spectrum radio communication system
  • Exclusive ID code to avoid interference from other FASST systems
  • Fail Safe (F/S) function, Battery F/S

Specification:

  • Communication system: one-way communication
  • Antenna: 1/2 wavelength di-pole
  • Current consumption: 150mA maximum
  • LED (light emitting diodes) indicate the operational status

€268.00

Inc. VAT
Jeti Duplex 2.4EX Transmitter module TU2 EX

Jeti Duplex 2.4EX Transmitter module TU2 EX

Jeti Duplex 2.4EX Transmitter module TU2 EX

DUPLEX TU2 EX module is suitable for all transmitters, especially for those with non-exchangeable HF plug-in modules. Installation is possible into almost all types of transmitters. There are only two main requirements: A transmitter with the possibility of operation in PPM
mode and space for the module in the transmitter. If needed, Duplex TU2 EX is also possible to put in the box and fit to the transmitter.

DUPLEX TU2 EX module is an enhanced version DUPLEX TU2. Along with the mounting kit it simplifies mounting SWTU2 to the transmitters. An assembly set VOICE-1 may be better adapted to the acoustic properties after incorporation into the transmitter.

Futaba:
FC-16, FC-18 JUNIOR, T6EXH
P, 12FG, 12Z, 14MZ, FX-18, FX-14, FX-30

Hitec:  
Laser 4, Laser 6, Flash 5, Optic 6 sport

Graupner:
MC-10, MC-12, MC-14, MC-15, MC-16, MC-19, MC-22, MC-16-20,
MX-12, MX-16s

Multiplex:
Cockpit SX
Profi 3000, 4000

€129.00

Inc. VAT
Quantity
Jumper  JP4-in-1 Multi-protocol RF Module for Frsky JR Flysky DEVO Esky WLtoys Hubsan

Jumper JP4-in-1 Multi-protocol RF Module for Frsky JR Flysky DEVO Esky WLtoys Hubsan

The JP4IN1 tuner module integrates the CC2500, NRF24L01, A7105, and CYRF6936 RF chips on a single board. The module itself is an openTX native accessory that can communicate serially with the frsky series of remote controls, as well as the PPM signal from the remote control output, and then convert to a corresponding remote control protocol for control of the receiver or aircraft. Currently supported agreements include: Walkera DEVO, Specturm DSM2, Flysky, Esky, Frsky, Weili, Hubsan, Chiyuan, Futaba SFHSS Assan and other agreements.
 
This tuner allows for more flexible and convenient control of four different drones, helicopters and fixed wings. Thanks to the continual use of the remote control you are familiar with, the operating feel and flight experience are also better.

JP4-in-1 Multi-protocol RF Module
Working voltage: 6-9v
Working current: <=100ma
Operating frequency: 2.4G ISM band
RF power: +22DBM
Main control chip: STM32F103CBT6 (128K ROM, 20K RAM)
Module bay compatibility: FRSky, Jr and other dimensions: 64*49*33 (without antenna)
Net Weight: 42g (including antenna)
Software Compatibility: Suitable for radios using OpenTX or er9x/ersky9x
Firmware updatable: Yes, via USB.
 
RF Chip Data   
 
Cypress Semiconductor CYRF6936: DSM/DSMX, Walkera Devo
Texas Instruments CC2500: FrSky, Futaba SFHSS
Amiccom A7105: FlySky, FlySky AFHDS2A, Hubsan
Nordic Semiconductor NRF24L01: HiSky, Syma, ASSAN and most other Chinese models
 
 RF Module Features:
 
The CC2500, NRF24L01, A7105 and CYRF6936 RF Chip modules all integrated on one board.
Convert standard PPM signals form module equipped radios in to the RF protocols
This module is plug and play with module equipped radios in the FrSKY series and requires
  no complex wiring or “hacking” to get running.
The Jumper JP4IN1 module is also upgradable via USB input
 
  Package Included:
 
1pcs* JP4-in-1 Multi-protocol RF Module

€59.00

Inc. VAT
RadioMaster - Ranger 2.4GHz ELRS Module LONG RANGE system

RadioMaster - Ranger 2.4GHz ELRS Module LONG RANGE system

Featuring an OLED display, a directional menu key, and two assignable shortcut keys the Ranger can be adjusted on the fly and personalized to your needs.

  • The Ranger includes a T Antenna for general use and a RadioMaster Moxon antenna for long-range directional applications. A micro module and nano module adapter are included to ensure the Ranger is compatible with most radios on the market today. A cable has also been included for use with Futaba radios that are CRSF capable.
  • Built-in Accelerometer;Packet rates up to F-1000Hz
  • Up to 1 Watt Power output;Wifi and Bluetooth support;High-efficiency cooling system

Features

  • OLED Display
  • Rugged CNC Case
  • Built-in Accelerometer
  • Packet rates up to F-1000Hz
  • Wifi and Bluetooth support
  • High-efficiency cooling system
  • 5 Direction Nav key and customizable shortcut buttons
  • Micro and Nano adapters included
  • Moxon and T-antenna included
  • CRSF cable for compatible Futaba radios included

    Specification
  • Item: Ranger 2.4GHz ELRS Module
  • Regulatory Domain: ISM2400
  • MCU: ESP32(main), ESP8285(aux, as ESP backpack)
  • RF chip: SX1281IMLTRT
  • Frequency Range: 2400 MHz - 2480 MHz
  • Maximum packet rate: 500Hz/F-1000Hz (F-1000Hz mode requires EgdeTX 2.7.1 or later)
  • Minimum receiver refresh rate: 25Hz
  • RF Output Power: Default 100mW
  • Module bay adapters: JR standard 5pin socket & Nano standard 8pin socket
  • Futaba CRSF socket cable: Included
  • OLED screen: 64x128px
  • Wifi Support: Yes
  • Bluetooth support: Yes
  • 3-Axis Accelerometer: Yes (STK8BA58 MEMS Accelerometer)
  • Built-in RGB light strip
  • XT30 Power supply voltage: DC 6V - 16.8V
  • Weight: 138g (with Moxon antenna) / 135g (with T antenna) / 126g (without antenna)
  • Dimension: 95*51*25mm (without antenna)

Please check local regulations for rules and permissions

Package including:

  • 1 * RANGER Module
  • 1 * Futaba CRSF socket cable
  • 1 * JR Adapter
  • 1 * Nano Adapter
  • 1 * T Antenna
  • 1 * Moxon Antenna
  • 1 * Hexagon socket screwdriver
  • 3 * M2*5 Screws
  • 1 * Assembly Manual

€109.00

Inc. VAT
Quantity
RadioMaster - TX16s Empty Module - Project box

RadioMaster - TX16s Empty Module - Project box

RadioMaster - TX16s Empty Module - Project box THIS box is made to add DIY module and Antenna. its an Optional part for Radiomaster TX16S

€3.99

Inc. VAT
Quantity
RadioMaster CNC Metal Upgrade Set Replacement Parts for TX16S Transmitter Red, Blue, Purple, Silver

RadioMaster CNC Metal Upgrade Set Replacement Parts for TX16S Transmitter Red, Blue, Purple, Silver

This is a kit of CNC parts to let you customize your TX16S to give it a unique look and premium feel.

An optional CNC, anodized metal parts set to upgrade your RADIOMASTER TX16S transmitter. Includes a folding carry handle, gimbal fascia's, roller wheel, stick knobs, rotary knobs, screws, washers, and much much more. Make your transmitter stand out from the crowd with one of these upgrade sets.

Description:

Brand Name: RadioMaster

Item Name: Upgrade Set

Material: CNC Metal

Color: Silver/Red/Blue/Purple

Weight: 134g

Compatible: for TX16S Transmitter

€69.90

Inc. VAT
Quantity
TBS Crossfire TX lite-Long range R/C TX module

TBS Crossfire TX lite-Long range R/C TX module

The TBS CROSSFIRE is a long range R/C link based on the newest RF technology, capable of self-healing two-way communications and range beyond comprehension. With a sensitivity of -130dB, full RF-side diveristy, tiny receivers for FPV quads, the TBS CROSSFIRE contains the most modern technology to provide a superior long range control link.

Remote control links, however, are tasked with much more than range. Latency, telemetry, robustness against interference, connectivity with smart devices, ease of use and the overall finish are too often sacrificed for that last bit of range. The Crossfire comes with plenty of range, and uses that margin for additional functionality and reliability. A bright future for FPV lies ahead :)

As a modern R/C link, it has telemetry built in. Two-way communication opens up new possibilities. From updating your firmware, setting your video transmitter channel to adjusting flight control parameters such as PIDs. Adaptive bandwidth controls the speed of transmission or optimizes for ultimate range. CRSF is a proprietary TBS communication protocol between the Crossfire and R/C and Flight Control. It provides ultra-low latency with incredible bandwidth (3x faster, 6x more data than any comparable protocol!). With such tight integration, the TBS Crossfire is the logical choice for anyone flying Betaflight, KiSS or ArduPilot/Pixhawk platforms.

Features:

    • Long range, adaptive and robust remote control system for your aircraft
    • Immune to on-board noise
    • Two-way communication link with real-time link vitals and telemetry
    • Self-healing & frequency hopping (DSSS, FHSS)
    • Adaptive bandwidth control and range optimization
    • Serial Modem capable of transmitting serial protocols (up & downlink)
    • RX beacon mode to recover your downed aircraft
    • Super easy binding and configuration via built-in display
    • Low latency, 150Hz update rate (3x faster than typical RC links) control for perfect immersive feeling
    • Two receiver models: 8ch Diversity Rx, 4ch PPM/SBUS Mini-receiver (4g weight!)
    • 8 or 12ch output via PPM/SBUS/CRSF on both receivers
    • Ability to fly with multiple friends at the same time (10 or more)
    • Selectable RF power from 10mW to 2W (local restrictions apply)
    • Dedicated head-tracking input option for full FPV immersion
    • Transmitter LED shows link health, OLED display for built in configuration
    • Short-Range mobile connectivity telemetry output for smartphone apps
    • Fully configurable by OpenTX and TBS TANGO remote using CRSF protocol
    • CRSF protocol interface to Betaflight, Kiss and Raceflight FCs ( lower latency, higher update rate, telemetry support )
    • Expansion port for future feature support
    • Micro-receiver for smaller drones. Smaller than you think!
    • Software updates via RF Link

Technical specifications:

  •     Frequency Band: 868MHz
  •     Input Voltage: 3.5 - 13V
  •     Power consumption: 1.1W (@10mW) - 3.2W (@2000mW)
  •     Dimensions: 55 x 89 x 15 mm
  •     Weight: 76g

Package includes:

  •     TBS Crossfire Transmitter
  •     TBS Crossfire JR Adapter
  •     TBS Crossfire Stock Tx Antenna V2
  •     Crossfire Futaba cable
  •     Crossfire Graupner  cable
  •     Crossfire PWM Pigtail
  •     Crossfire JST to XT30 cable

€189.00

Inc. VAT
Quantity